arXiv subjects

Erik G. Larsson

Publications and source records attributed to Erik G. Larsson.

At least 37 records · Page 2Linked to original sources

arXiv2026

Experimental Study of Interference Suppression for Backscatter Communication in Distributed MIMO

Bistatic backscatter communication requires strong illumination of a backscatter device (BD), while a spatially separated reader detects the weak modulated reflection. In practice, the resulting direct link interference (DLI) at the reader can dominate the received backscattered signal and limit detection performance. This paper experimentally investigates transmit beamforming that jointly maximizes BD illumination and suppresses DLI at the reader in a distributed multiple-input multiple-output setup. We compare phase-only maximum ratio transmission (PO-MRT) with the proposed direct-link suppression (DLS) scheme, which enforces a spatial null at the reader under per-antenna power constraints. Measurements using a phase-coherent 42-element ceiling array at 920 MHz show that DLS reduces the DLI at the target reader and improves the signal-to-interference ratio by up to 31 dB compared to PO-MRT.

eess.SP↗

arXiv2026

Repeater-Aided Over-the-Air Phase Synchronization in Distributed MIMO

Phase synchronization of access points (APs) in a distributed multiple-input multiple-output (D-MIMO) system is critical to leverage the performance benefits of D-MIMO. Existing over-the-air phase synchronization methods assume that APs can communicate directly to perform necessary measurements. However, this assumption might not hold in scenarios where inter-AP signaling is too weak for effective communication. To address this, in this paper, we propose a novel over-the-air calibration scheme that uses repeater nodes to facilitate phase synchronization when direct AP signaling is infeasible. We give the steps of the algorithm for phase calibration in closed form, and show how it enables coherent joint transmission (CJT) by the APs. The framework expands the applicability of D-MIMO systems to challenging environments, where existing over-the-air synchronization techniques fall short.

cs.IT↗

arXiv2026

On the Performance of Dual-Antenna Repeater Assisted Bi-Static MIMO ISAC

This paper presents a framework for target detection and downlink data transmission in a repeater-assisted bi-static integrated sensing and communication system. A repeater is an active scatterer that retransmits incoming signals with a complex gain almost instantaneously, thereby enhancing sensing performance by amplifying the echoes reflected by the targets. The same mechanism can also improve downlink communication by mitigating coverage holes. However, the repeater introduces noise and increases interference at the sensing receiver, while also amplifying the interference from target detection signals at the downlink users. The proposed framework accounts for these sensing-communication trade-offs and demonstrates the potential benefits achievable through a carefully designed precoder at the transmitting base station. In particular, our finding is that a higher value of probability of detection can be attained with considerably lower target radar-cross-section variance by deploying repeaters in the target hot-spot areas.

eess.SP↗

arXiv2026

Reciprocity Calibration of Dual-Antenna Repeaters via MMSE Estimation

This paper proposes a novel Bayesian reciprocity calibration method that consistently ensures uplink and downlink channel reciprocity in repeater-assisted multiple-input multiple-output (MIMO) systems. The proposed algorithm is formulated under the minimum mean-square error (MMSE) criterion. Its Bayesian framework incorporates complete statistical knowledge of the signal model, noise, and prior distributions, enabling a coherent design that achieves both low computational complexity and high calibration accuracy. To further enhance phase alignment accuracy, which is critical for calibration tasks, we develop a von Mises denoiser that exploits the fact that the target parameters lie on the circle in the complex plane. Simulation results demonstrate that the proposed MMSE algorithm achieves substantially improved estimation accuracy compared with conventional deterministic non-linear least-squares (NLS) methods, while maintaining comparable computational complexity. Furthermore, the proposed method exhibits remarkably fast convergence, making it well suited for practical implementation.

eess.SP↗

arXiv2026

Hybrid Channel Estimation with Quantized Phase Feedback for Over-the-Air Computation

To reduce the signaling overhead of over-the-air computation, a hybrid channel estimation scheme is proposed, where reciprocity-based and feedback-based channel estimation are combined. In particular, the impact of quantized phase-feedback is studied while the amplitude is assumed estimated exactly. The scheme enables selecting the estimation precision of amplitude and phase separately, depending on the importance of each. Two variants of the scheme are proposed: As shown through simulations and theory, the second variant with reciprocity-based estimation of the channel phase, and optimal quantization of phase feedback, can outperform the first variant estimating the phase by feedback only.

eess.SP↗

arXiv2026

Drone Surveillance via Coordinated Beam Sweeping in MIMO-ISAC Networks

This paper introduces a scheme for drone surveillance coordinated with the fifth generation (5G) synchronization signal block (SSB) cell-search procedure to simultaneously detect low-altitude drones within a volumetric surveillance grid. Herein, we consider a multistatic configuration where multiple access points (APs) collaboratively illuminate the volume while independently transmitting SSB broadcast signals. Both tasks are performed through a beam sweeping. In the proposed scheme, coordinated APs send sensing beams toward a grid of voxels within the volumetric surveillance region simultaneously with the 5G SSB burst. To prevent interference between communication and sensing signals, we propose a precoder design that guarantees orthogonality of the sensing beam and the SSB in order to maximize the sensing signal-to-interference-plus-noise ratio (SINR) while ensuring a specified SINR for users, as well as minimizing the impact of the direct link. The results demonstrate that the proposed precoder outperforms the non-coordinated precoder and is minimally affected by variations in drone altitude.

eess.SP↗

arXiv2026

Repeater Swarm-Assisted Cellular Systems: Interaction Stability and Performance Analysis

We consider a cellular massive MIMO system where swarms of wireless repeaters are deployed to improve coverage. These repeaters are full-duplex relays with small form factors that receive and instantaneously retransmit signals. They can be deployed in a plug-and-play manner at low cost, while being transparent to the network--conceptually they are active channel scatterers with amplification capabilities. Two fundamental questions need to be addressed in repeater deployments: (I) How can we prevent destructive effects of positive feedback caused by inter-repeater interaction (i.e., each repeater receives and amplifies signals from others)? (ii) How much performance improvement can be achieved given that repeaters also inject noise and may introduce more interference? To answer these questions, we first derive a generalized Nyquist stability criterion for the repeater swarm system, and provide an easy-to-check stability condition. Then, we study the uplink performance and develop an efficient iterative algorithm that jointly optimizes the repeater gains, user transmit powers, and receive combining weights to maximize the weighted sum rate while ensuring system stability. Numerical results corroborate our theoretical findings and show that the repeaters can significantly improve the system performance, both in sub-6 GHz and millimeter-wave bands. The results also warrant careful deployment to fully realize the benefits of repeaters, for example, by ensuring a high probability of line-of-sight links between repeaters and the base station.

cs.IT↗

arXiv2025

Radio over Fiber with Cascaded Structure: Algorithm for Uplink Positioning

Recent advancements in polymer microwave fiber (PMF) technology have created significant opportunities for robust, low-cost, and high-speed sub-terahertz (THz) radio-over-fiber communications. Recognizing these potential benefits, this paper explores a novel radio-over-fiber (RoF) structure that interconnects multiple radio units (RUs) in cascade via fiber, envisioning its application in indoor scenarios. This structure creates a number of research opportunities when considering cascaded distortion effects introduced by non-linear power amplifiers (PAs) at the RUs and the propagation channel over the fiber. We propose maximum-likelihood and non-linear least-squares algorithms to estimate the propagation distance along the RoF and the time-of-arrival between the RoF and the user equipment. For the case of linear PAs, we derive the Cramér-Rao lower bound to benchmark the performance of the estimators. Finally, we investigate the use of the system for uplink positioning. Our simulation results demonstrate that the proposed estimators perform satisfactorily even with the cascaded effects of non-linear PAs, and that the deployment of this RoF structure can enable new cost-effective opportunities for high-resolution positioning in indoor scenarios. In the numerical evaluation, we also use measured PMF characteristics for high-density polyethylene fibers.

eess.SP↗

arXiv2025

Scheduling and Aggregation Design for Asynchronous Federated Learning over Wireless Networks

Federated Learning (FL) is a collaborative machine learning (ML) framework that combines on-device training and server-based aggregation to train a common ML model among distributed agents. In this work, we propose an asynchronous FL design with periodic aggregation to tackle the straggler issue in FL systems. Considering limited wireless communication resources, we investigate the effect of different scheduling policies and aggregation designs on the convergence performance. Driven by the importance of reducing the bias and variance of the aggregated model updates, we propose a scheduling policy that jointly considers the channel quality and training data representation of user devices. The effectiveness of our channel-aware data-importance-based scheduling policy, compared with state-of-the-art methods proposed for synchronous FL, is validated through simulations. Moreover, we show that an ``age-aware'' aggregation weighting design can significantly improve the learning performance in an asynchronous FL setting.

cs.LG↗

arXiv2025

A Unified Convergence Analysis for Semi-Decentralized Learning: Sampled-to-Sampled vs. Sampled-to-All Communication

In semi-decentralized federated learning, devices primarily rely on device-to-device communication but occasionally interact with a central server. Periodically, a sampled subset of devices uploads their local models to the server, which computes an aggregate model. The server can then either (i) share this aggregate model only with the sampled clients (sampled-to-sampled, S2S) or (ii) broadcast it to all clients (sampled-to-all, S2A). Despite their practical significance, a rigorous theoretical and empirical comparison of these two strategies remains absent. We address this gap by analyzing S2S and S2A within a unified convergence framework that accounts for key system parameters: sampling rate, server aggregation frequency, and network connectivity. Our results, both analytical and experimental, reveal distinct regimes where one strategy outperforms the other, depending primarily on the degree of data heterogeneity across devices. These insights lead to concrete design guidelines for practical semi-decentralized FL deployments.

cs.LG↗

arXiv2025

Joint Access Point Selection and Beamforming Design for Bistatic Backscatter Communication

Future Internet-of-Things networks are envisioned to use small and cheap sensor nodes with extremely low power consumption to avoid the extensive use of batteries. To provide connectivity to a massive number of these nodes, backscatter communication (BC) is emerging as an energy- and cost-efficient technology exploiting the reflection of radio frequency signals. However, challenges such as round-trip path loss and direct link interference (DLI) between the carrier emitter and the reader limit its performance. To tackle these limitations, this paper proposes a joint access point role selection and a novel beamforming technique for bistatic BC in a distributed multiple-input multiple-output setup. The proposed approach boosts the received backscattered energy while effectively mitigating DLI, thereby reducing the error probability. We also propose a channel estimation method tailored to operate under DLI conditions and propose a mismatch detector using estimated channel coefficients. Furthermore, we derive a closed-form expression for the probability of error for the detectors and model the quantization noise caused by DLI. Finally, comprehensive simulation results show that the proposed method with 1-bit analog-to-digital converters (ADCs) effectively mitigates DLI, reduces the quantization noise, and enhances backscattered signal energy, achieving performance comparable to the benchmark scenario with 8-bit ADCs.

eess.SP↗

arXiv2025

Time-Varying Optimization for Streaming Data Via Temporal Weighting

Classical optimization theory deals with fixed, time-invariant objective functions. However, time-varying optimization has emerged as an important subject for decision-making in dynamic environments. In this work, we study the problem of learning from streaming data through a time-varying optimization lens. Unlike prior works that focus on generic formulations, we introduce a structured, \emph{weight-based} formulation that explicitly captures the streaming-data origin of the time-varying objective, where at each time step, an agent aims to minimize a weighted average loss over all the past data samples. We focus on two specific weighting strategies: (1) uniform weights, which treat all samples equally, and (2) discounted weights, which geometrically decay the influence of older data. For both schemes, we derive tight bounds on the ``tracking error'' (TE), defined as the deviation between the model parameter and the time-varying optimum at a given time step, under gradient descent (GD) updates. We show that under uniform weighting, the TE vanishes asymptotically with a $\mathcal{O}(1/t)$ decay rate, whereas discounted weighting incurs a nonzero error floor controlled by the discount factor and the number of gradient updates performed at each time step. Our theoretical findings are validated through numerical simulations.

cs.LG↗

arXiv2025

Propagation Distance Estimation for Radio over Fiber with Cascaded Structure

Recent developments in polymer microwave fiber (PMF) have opened great opportunities for robust, low-cost, and high-speed sub-terahertz (THz) communications. Noticing this great potential, this paper addresses the problem of estimation of the propagation distance of a sub-Thz signal along a radio over fiber structure. Particularly, this paper considers a novel cascaded structure that interconnects multiple radio units (RUs) via fiber for applications in indoor scenarios. Herein, we consider the cascaded effects of distortions introduced by non-linear power amplifiers at the RUs, and the propagation channel over the fiber is based on measurements obtained from transmissions of sub-THz signals on high-density polyethylene fibers. For the estimation of the propagation distance, non-linear least-squares algorithms are proposed, and our simulation results demonstrate that the proposed estimators present a good performance on the propagation distance estimation even in the presence of the cascaded effect of non-linear PAs.

eess.SP↗

arXiv2025

Computing frustration and near-monotonicity in deep neural networks

For the signed graph associated to a deep neural network, one can compute the frustration level, i.e., test how close or distant the graph is to structural balance. For all the pretrained deep convolutional neural networks we consider, we find that the frustration is always less than expected from null models. From a statistical physics point of view, and in particular in reference to an Ising spin glass model, the reduced frustration indicates that the amount of disorder encoded in the network is less than in the null models. From a functional point of view, low frustration (i.e., proximity to structural balance) means that the function representing the network behaves near-monotonically, i.e., more similarly to a monotone function than in the null models. Evidence of near-monotonic behavior along the partial order determined by frustration is observed for all networks we consider. This confirms that the class of deep convolutional neural networks tends to have a more ordered behavior than expected from null models, and suggests a novel form of implicit regularization.

cs.LG↗

arXiv2025

Breaking the TDD Flow for Over-the-Air Phase Synchronization in Distributed Antenna Systems

Phase synchronization between distributed antenna arrays requires measurements that break the standard time-division duplex (TDD) operation. We present a feasibility study on implementing such synchronization and analyze its impact on the quality of service. Considering two antenna arrays with independent local oscillators (LOs), we propose a modified TDD flow to accommodate the transmission of phase synchronization signals, formulate the phase estimation and compensation problem, and derive the achievable downlink spectral efficiency (SE). Numerical results show that frequent re-estimation of the interarray phase disparity is essential for maximizing SE in systems with low-quality LOs. Furthermore, applying a Kalman filter for phase tracking substantially improves the SE, especially if phase estimation errors are large compared to LOs phase drifts.

cs.IT↗

arXiv2025

Distributed Deployment and Dual-Frequency Concepts to Strengthen Sub-THz Wireless Systems

The vast bandwidth available at sub-THz frequencies holds great promise for high-speed wireless access, precise localization, and advanced sensing applications. However, fundamental physical constraints and technological limitations make the deployment of reliable sub-THz networks challenging. We propose a new paradigm for sub-THz coverage by transmitting the RF signals over polymer microwave fibers (PMFs) that interconnect low-complexity radio units (RUs) in a daisy-chain configuration. The distributed architecture ensures that user equipments (UEs) connect to RUs in their proximity, reducing path loss and mitigating blocking. The RUs leverage low-complexity, compact integrated antenna modules. Additionally, dual-frequency tandem operation is proposed, integrating the sub-THz system with a sub-10 GHz system that provides control signalling and a robust fallback solution for the sub-THz system. This proposed tandem architecture can open up the full potential of sub-THz technology and paves the way to cost- and energy-efficient, high-performance, real-time connectivity in dynamic environments.

eess.SP↗

arXiv2025

Industrial Viewpoints on RAN Technologies for 6G

6G standardization is to start imminently, with commercial deployments expected before 2030. Its technical components and performance requirements are the focus of this article. Our emphasis is on the 6G radio access, especially MIMO, AI, waveforms, coding, signal constellations and integration with non-terrestrial networks. Whilst standardization has not yet formally started, the scope of the 6G study items has been defined. Our predictions in this paper are speculative as there are no results of the study yet, but our views are guided by implementation and deployment aspects. We expect that the views here will guide researchers and industry practitioners.

cs.NI↗

arXiv2025

Joint Sensing and Bi-Directional Communication with Dynamic TDD Enabled Cell-Free MIMO

This paper studies integrated sensing and communication (ISAC) with dynamic time division duplex (DTDD) cell-free (CF) massive multiple-input multiple-output~(mMIMO) systems. DTDD enables the CF mMIMO system to concurrently serve both uplink~(UL) and downlink~(DL) users with spatially separated \emph{half-duplex~(HD)} access points~(APs) using the same time-frequency resources. Further, to facilitate ISAC, the UL APs are utilized for both UL data and target echo reception, while the DL APs jointly transmit the precoded DL data streams and target signal. In this context, we present centralized and distributed generalized likelihood-ratio tests~(GLRTs) for target detection treating UL users' signals as sensing interference. We then quantify the optimality and complexity trade-off between distributed and centralized GLRTs and benchmark the respective estimators with the Bayesian Cramér-Rao lower bound for target radar-cross section~(RCS). Then, we present a unified framework for joint UL users' data detection and RCS estimation. Next, for communication, we derive the signal-to-noise-plus-interference~(SINR) optimal combiner accounting for the cross-link and radar interference for UL data processing. In DL, we use regularized zero-forcing for the users and propose two types of precoders for the target: one ``user-centric" that nullifies the interference caused by the target signal to the DL users and one ``target-centric" based on the dominant eigenvector of the composite channel between the target and the APs. Finally, numerical studies corroborate with our theoretical findings and reveal that the \emph{GLRT is robust to inter-AP interference, and DTDD doubles the $90\%$-likely sum UL-DL SE compared to traditional TDD-based CF-mMIMO ISAC systems}; while using HD hardware.

eess.SP↗