arXiv subjects
Publications and source records attributed to Etsushi Yamazaki.
We successfully transmitted a net 582-Gb/s probabilistically shaped PAM12 C-band signal over 11-km dispersion-shifted fibre and net 4$\times$526-Gb/s uniform PAM8 O-band signals over 2-km four-core fibre using a single-carrier 216-GBd IMDD system based on a 150-GHz bandwidth InP-DHBT electrical mixer and a thin-film lithium-niobate modulator.
Optical link tomography (OLT) is a rapidly evolving field that allows the multi-span, end-to-end visualization of optical power along fiber links in multiple dimensions from network endpoints, solely by processing signals received at coherent receivers. This paper has two objectives: (1) to report the first field trial of OLT, using a commercial transponder under standard DWDM transmission, and (2) to extend its capability to visualize across 4D (distance, time, frequency, and polarization), allowing for locating and measuring multiple QoT degradation causes, including time-varying power anomalies, spectral anomalies, and excessive polarization dependent loss. We also address a critical aspect of OLT, i.e., its need for high fiber launch power, by improving power profile signal-to-noise ratio through averaging across all available dimensions. Consequently, multiple loss anomalies in a field-deployed link are observed even at launch power lower than the system-optimal level. The applications and use cases of OLT from network commissioning to provisioning and operation for current and near-term network scenarios are also discussed.
Data center networks (DCNs) require a low-cost, low-power optical transceiver to handle increased traffic from generative artificial intelligence, video streaming services, and more. Improving the required signal-to-noise ratio (RSNR) by digital signal processing such as forward error correction (FEC) mitigates the requirements for electrical and optical components. The optical transceivers in DCNs exploit a low-complexity soft-decision (SD) FEC, consisting of short block-length linear error-correcting codes and a low-complexity SD decoder (SDD), such as Chase decoding and ordered statistics decoding. The low-complexity SDD efficiently approaches a maximum likelihood decoding (MLD). However, the decoding performance of MLD is limited by its finite block length. In this paper, we describe the details of our proposed channel-polarized multilevel coding with iterative decoding (CP-MLC-ID). The proposed CP-MLC-ID improves the decoding performance by extending the codeword length to weakly and indirectly connect codewords via bypassed bits. The 19.5%-OH CP-MLC-ID using 128-bit extended Bose-Chaudhuri-Hocquenghem (eBCH) and KP4 codes outperforms the concatenated eBCH and KP4 codes with a net coding gain of 0.25 and 0.40 dB for the same and double the number of SDDs, respectively. We also investigate the dependency of the decoding performance on the size of a bit interleaver. The performance degradation of CP-MLC-ID using an 8-bit interleaver is about 0.1 dB compared to using the large-bit interleaver. Our results indicate that even a weak connection by exclusive-OR between codewords improves the decoding performance, compared to simple concatenated codes in the DCNs.
In this paper, we experimentally and theoretically show the improvement in noise characteristics in a distributed Raman amplifier (DRA) system for wavelength division multiplexing (WDM) transmission, utilizing our proposed pumping technique. We show that forward (Fwd) pumping is clearly superior to backward (Bwd) pumping in terms of noise figure (NF) defined by amplified spontaneous emission (ASE) noise and gain. We also show that bi-directional pumping is a more desirable configuration for NF improvement. However, it is known that Bwd pumping is preferable to Fwd pumping in suppressing signal quality degradation caused by nonlinear optical effects, especially the interaction between signal and pump light. To compare these advantages and disadvantages of Fwd pumping, we conducted WDM transmission experiments using a recirculating loop including DRA and erbium doped fiber amplifiers. We measured the Q-factors of 9-channel 131.6-GBaud polarization division multiplexed probabilistically shaped 32-quadrature amplitude modulation signals while changing the ratio of Fwd pumping to Bwd pumping in the DRA. By introducing the previously proposed low-noise Fwd pumping technique, a higher Q-factor could be achieved with a lower signal launch power, even when the total Raman gain remained constant. A Q-factor improvement of 0.4 dB and signal launch power reduction of more than 3.4 dB were simultaneously achieved. We also show that when Fwd pumping was performed with a conventional pump light source, the disadvantage of Fwd pumping was more noticeable than its advantage.
This paper presents a linear least squares method for fiber-longitudinal power profile estimation (PPE), which estimates an optical signal power distribution throughout a fiber-optic link at a coherent receiver. The method finds the global optimum in least square estimation of longitudinal power profiles, thus closely matching true optical power profiles and locating loss anomalies in a link with high spatial resolution. Experimental results show that the method achieves accurate PPE with an RMS error from OTDR of 0.18 dB. Consequently, it successfully identifies a loss anomaly as small as 0.77 dB, demonstrating the potential of a coherent receiver in locating even splice and connector losses. The method is also evaluated under a WDM condition with optimal system fiber launch power, highlighting its feasibility for use in operations. Furthermore, a fundamental limit for stable estimation and spatial resolution of least-squares-based PPE is quantitatively discussed in relation to the ill-posedness of PPE by evaluating the condition number of a nonlinear perturbation matrix.
This paper presents analytical results on longitudinal power profile estimation (PPE) methods, which visualize signal power evolution in optical fibers at a coherent receiver. The PPE can be formulated as an inverse problem of the nonlinear Schrödinger equation, where the nonlinear coefficient (and thus signal power) is reconstructed from boundary conditions, i.e., transmitted and received signals. Two types of PPE methods are reviewed and analyzed, including correlation-based methods (CMs) and minimum-mean-square-error-based methods (MMSEs). The analytical expressions for their output power profiles and spatial resolution are provided, and thus the theoretical performance limits of the two PPE methods and their differences are clarified. The derived equations indicate that the estimated power profiles of CMs can be understood as the convolution of a true power profile and a smoothing function. Consequently, the spatial resolution and measurement accuracy of CMs are limited, even under noiseless and distortionless conditions. Closed-form formulas for the spatial resolution of CMs are shown to be inversely proportional to the product of a chromatic dispersion coefficient and the square of signal bandwidth. With MMSEs, such a convolution effect is canceled out and the estimated power profiles approach a true power profile under a fine spatial step size.
In optical fiber communication, system identification (SI) for the nonlinear Schrödinger equation (NLSE) has long been studied mainly for fiber nonlinearity compensation (NLC). One recent line of inquiry to combine a behavioral-model approach like digital backpropagation (DBP) and a data-driven approach like neural network (NN). These works are aimed for more NLC gain; however, by directing our attention to the learned parameters in such a SI process, system status information, i.e., optical fiber parameters, will possibly be extracted. Here, we show that the model-based optimization and interpretable nature of the learned parameters in NN-based DBP enable transmission line monitoring, fully extracting the actual in-line NLSE parameter distributions. Specifically, we demonstrate that longitudinal loss and dispersion profiles along a multi-span link can be obtained at once, directly from data-carrying signals without any dedicated analog devices such as optical time-domain reflectometry. We apply the method to a long-haul (~2,080 km) link and various link conditions are tested, including excess loss inserted, different fiber input power, and non-uniform level diagram. The measurement performance is also investigated in terms of measurement range, accuracy, and fiber launch power. These results provide a path toward simplified and automated network management as another application of DBP.
We present a simple nonlinear digital pre-distortion (DPD) of optical transmitter components, which consists of concatenated blocks of a finite impulse response (FIR) filter, a memoryless nonlinear function and another FIR filter. The model is a Wiener-Hammerstein (WH) model and has essentially the same structure as neural networks or multilayer perceptions. This awareness enables one to achieve complexity-efficient DPD owing to the model-aware structure and exploit the well-developed optimization scheme in the machine learning field. The effectiveness of the method is assessed by electrical and optical back-to-back (B2B) experiments, and the results show that the WH DPD offers a 0.52-dB gain in signal-to-noise ratio (SNR) and 6.0-dB gain in optical modulator output power at a fixed SNR over linear-only DPD.
Nonlinearities can be introduced into communication systems by the physical components such as the power amplifier, or during signal propagation through a nonlinear channel. These nonlinearities can be compensated by a nonlinear equalizer at the receiver side. The nonlinear equalizer also operates on the additive noise, which can lead to noise enhancement. In this work we evaluate this trade-off between distortion reduction and noise-enhancement via nonlinear equalization techniques. We first, evaluate the trade-off between nonlinearity compensation and noise enhancement for the Volterra equalizer, and propose a method to determine the training SNR that optimizes this performance trade-off. We then propose a new approach for nonlinear equalization that alternates between neural networks (NNs) for nonlinearity compensation, and belief propagation (BP) for noise removal. This new approach achieves a 0.6 dB gain compared to the Volterra equalizer with the optimal training SNR, and a 1.7 dB gain compared to a system with no nonlinearity compensation.