arXiv subjects

F. A. Volpe

Publications and source records attributed to F. A. Volpe.

At least 19 recordsLinked to original sources

arXiv2018

Feedforward and feedback control of locked mode phase and rotation in DIII-D with application to modulated ECCD experiments

The toroidal phase and rotation of otherwise locked magnetic islands of toroidal mode number n=1 are controlled in the DIII-D tokamak by means of applied magnetic perturbations of n=1. Pre-emptive perturbations were applied in feedforward to "catch" the mode as it slowed down and entrain it to the rotating field before complete locking, thus avoiding the associated major confinement degradation. Additionally, for the first time, the phase of the perturbation was optimized in real-time, in feedback with magnetic measurements, in order for the mode's phase to closely match a prescribed phase, as a function of time. Experimental results confirm the capability to hold the mode in a given fixed-phase or to rotate it at up to 20 Hz with good uniformity. The control coil currents utilized in the experiments agree with the requirements estimated by an electromechanical model. Moreover, controlled rotation at 20 Hz was combined with Electron Cyclotron Current Drive (ECCD) modulated at the same frequency. This is simpler than regulating the ECCD modulation in feedback with spontaneous mode rotation, and enables repetitive, reproducible ECCD deposition at or near the island O-point, X-point and locations in between, for careful studies of how this affects the island stability. Current drive was found to be radially misaligned relative to the island, and resulting growth and shrinkage of islands matched expectations of the Modified Rutherford Equation for some discharges presented here. Finally, simulations predict the as designed ITER 3D coils can entrain a small island at sub-10 Hz frequencies.

physics.plasm-ph↗

arXiv2017

Overdense microwave plasma heating in the CNT stellarator

Overdense plasmas have been attained with 2.45 GHz microwave heating in the low-field, low-aspect-ratio CNT stellarator. Densities higher than four times the ordinary (O) mode cutoff density were measured with 8 kW of power injected in the O-mode and, alternatively, with 6.5 kW in the extraordinary (X) mode. The temperature profiles peak at the plasma edge. This was ascribed to collisional damping of the X-mode at the upper hybrid resonant layer. The X-mode reaches that location by tunneling, mode-conversions or after polarization-scrambling reflections off the wall and in-vessel coils, regardless of the initial launch being in O- or X-mode. This interpretation was confirmed by full-wave numerical simulations. Also, as the CNT plasma is not completely ionized at these low microwave power levels, electron density was shown to increase with power. A dependence on magnetic field strength was also observed (for O-mode launch) and discussed.

physics.plasm-ph↗

arXiv2017

High-$β$ equilibrium and ballooning stability of the low aspect ratio CNT stellarator

The existence and ballooning-stability of low aspect ratio stellarator equilibria is predicted for CNT with the aid of 3D numerical tools. In addition to having a low aspect ratio, CNT is characterized by a low magnetic field and small plasma volume. Also, highly overdense plasmas were recently heated in CNT by means of microwaves. These characteristics suggest that CNT might attain relatively high values of plasma $β$ and thus be of use in the experimental study of stellarator stability to high-$β$ instabilities such as ballooning modes. As a first step in that direction, here the ballooning stability limit is found numerically. Depending on the particular magnetic configuration we expect volume-averaged $β$ limits in the range 0.9-3.0%, and possibly higher, and observe indications of a second region of ballooning stability. As the aspect ratio is reduced, stability is found to increase in some configurations and decrease in others. Energy-balance estimates using stellarator scaling laws indicate that the lower $β$ limit may be attainable with overdense heating at powers of of 40 to 100 kW. The present study serves the additional purpose of testing VMEC and other stellarator codes at high values of $β$ and at low aspect ratios. For this reason, the study was carried out both for free boundary, for maximum fidelity to experiment, as well as with a fixed boundary, as a numerical test.

physics.plasm-ph↗

arXiv2017

Passive and active electromagnetic stabilization of free-surface liquid metal flows

Free-surface liquid metal flows tend to be uneven due to instabilities and other effects. Some applications, however, require constant, uniform liquid metal thickness. This is for example the case of liquid walls in nuclear fusion reactors. With this motivation, here we present experimental results on the stabilization of a free-surface flow of Galinstan. The flow was sustained by an electromagnetic induction pump featuring rotating permanent magnets. Evidence is reported of the flowing Galinstan layer becoming flatter in the presence of a sufficiently strong magnetic field, either alone (passive stabilization) or in combination with an electrical current passing through the liquid metal (active stabilization). The results are interpreted in terms of an effective viscosity and effective gravity, respectively.

physics.plasm-ph↗

arXiv2016

Statistical analysis of $m/n$ = 2/1 locked and quasi-stationary modes with rotating precursors at DIII-D

A database has been developed to study the evolution, the nonlinear effects on equilibria, and the disruptivity of locked and quasi-stationary modes with poloidal and toroidal mode numbers $m=2$ and $n=1$ at DIII-D. The analysis of 22,500 discharges shows that more than 18% of disruptions are due to locked or quasi-stationary modes with rotating precursors (not including born locked modes). A parameter formulated by the plasma internal inductance $l_i$ divided by the safety factor at 95% of the poloidal flux, $q_{95}$, is found to exhibit predictive capability over whether a locked mode will cause a disruption or not, and does so up to hundreds of milliseconds before the disruption. Within 20 ms of the disruption, the shortest distance between the island separatrix and the unperturbed last closed flux surface, referred to as $d_{edge}$, performs comparably to $l_i/q_{95}$ in its ability to discriminate disruptive locked modes. Out of all parameters considered, $d_{edge}$ also correlates best with the duration of the locked mode. Within 50 ms of a locked mode disruption, average behavior includes exponential growth of the $n=1$ perturbed field, which might be due to the 2/1 locked mode. Even assuming the aforementioned 2/1 growth, disruptivity following a locked mode shows little dependence on island width up to 20 ms before the disruption. Separately, greater deceleration of the rotating precursor is observed when the wall torque is large. At locking, modes are often observed to align with a residual error field. Timescales associated with the mode evolution are also studied and dictate the response times necessary for disruption avoidance and mitigation.

physics.plasm-ph↗

arXiv2016

Resistive sensor and electromagnetic actuator for feedback stabilization of liquid metal walls in fusion reactors

Liquid metal walls in fusion reactors will be subject to instabilities, turbulence, induced currents, error fields and temperature gradients that will make them locally bulge, thus entering in contact with the plasma, or deplete, hence exposing the underlying solid substrate. To prevent this, research has begun to actively stabilize static or flowing liquid metal layers by locally applying forces in feedback with thickness measurements. Here we present resistive sensors of liquid metal thickness and demonstrate jxB actuators, to locally control it.

physics.ins-det↗

arXiv2016

Space- and Time-resolved Resistive Measurement of Liquid Metal Wall Thickness

In a fusion reactor internally coated with liquid metal, it will be important to diagnose the thickness of the liquid at various locations in the vessel, as a function of time, and possibly respond to counteract undesired bulging or depletion. The electrical conductance between electrodes immersed in the liquid metal can be used as a simple proxy for the local thickness. Here a matrix of electrodes is shown to provide spatially resolved measurements of liquid metal thickness in the absence of plasma. First a theory is developed for mxn electrodes, and then it is experimentally demonstrated for 3x1 electrodes. The experiments were carried out with Galinstan, but are easily extended to Lithium or other liquid metals.

physics.plasm-ph↗

arXiv2016

Onion-peeling inversion of stellarator images

An onion-peeling technique is developed for inferring the emissivity profile of a stellarator plasma from a two-dimensional image acquired through a CCD or CMOS camera. Each pixel in the image is treated as an integral of emission along a particular line-of-sight. Additionally, the flux surfaces in the plasma are partitioned into discrete layers, each of which is assumed to have uniform emissivity. If the topology of the flux surfaces is known, this construction permits the development of a system of linear equations that can be solved for the emissivity of each layer. We present initial results of this method applied to wide-angle visible images of the CNT stellarator plasma.

physics.plasm-ph↗

arXiv2016

Full-Wave Feasibility Study of Anti-Radar Diagnostic of Magnetic Field Based on O-X Mode Conversion and Oblique Reflectometry Imaging

An innovative millimeter wave diagnostic is proposed to measure the local magnetic field and edge current as a function of the minor radius in the tokamak pedestal region. The idea is to identify the direction of minimum reflectivity at the O-mode cutoff layer. Correspondingly, the transmissivity due to O-X mode conversion is maximum. That direction, and the angular map of reflectivity around it, contain information on the magnetic field vector B at the cutoff layer. Probing the plasma with different wave frequencies provides the radial profile of B. Full-wave finite-element simulations are presented here in 2D slab geometry. Modeling confirms the existence of a minimum in reflectivity that depends on the magnetic field at the cutoff, as expected from mode conversion physics, giving confidence in the feasibility of the diagnostic. The proposed reflectometric approach is expected to yield superior signal-to-noise ratio and to access wider ranges of density and magnetic field, compared with related radiometric techniques that require the plasma to emit Electron Bernstein Waves. Due to computational limitations, frequencies of 10-20 GHz were considered in this initial study. Frequencies above the edge electron-cyclotron frequency (f>28 GHz here) would be preferable for the experiment, because the upper hybrid resonance and right cutoff would lie in the plasma, and would help separate the O-mode of interest from spurious X-waves.

physics.plasm-ph↗

arXiv2016

Huygens-Fresnel wavefront tracing in non-uniform media

We present preliminary results on a novel numerical method describing wave propagation in non-uniform media. Following Huygens-Fresnel' principle, we model the wavefront as an array of point sources that emit wavelets, which interfere. We then identify a set of new points where the electric field has equal phase. In fact, without losing generality, we find zeros of the electric field, by means of the bisection method. This obviously corresponds to a specific phase-advance, but is easily generalized, e.g. by phase-shifting all sources. The points found form the new wavefront. One of the advantages of the method is that it includes diffraction. Two examples provided are diffraction around an obstacle and the finite waist of a focused Gaussian beam. Refraction is also successfully modeled, both in slowly-varying media as well as in the presence of discontinuities. The calculations were performed in two dimensions, but can be easily extended to three dimensions. We also discuss the extension to anisotropic, birefringent, absorbing media.

physics.comp-ph↗

arXiv2016

Experimental and numerical study of error fields in the CNT stellarator

Sources of error fields were indirectly inferred in a stellarator by reconciling computed and numerical flux surfaces. Sources considered so far include the displacements and tilts (but not the deformations, yet) of the four circular coils featured in the simple CNT stellarator. The flux surfaces were measured by means of an electron beam and phosphor rod, and were computed by means of a Biot-Savart field-line tracing code. If the ideal coil locations and orientations are used in the computation, agreement with measurements is poor. Discrepancies are ascribed to errors in the positioning and orientation of the in-vessel interlocked coils. To that end, an iterative numerical method was developed. A Newton-Raphson algorithm searches for the coils' displacements and tilts that minimize the discrepancy between the measured and computed flux surfaces. This method was verified by misplacing and tilting the coils in a numerical model of CNT, calculating the flux surfaces that they generated, and testing the algorithm's ability to deduce the coils' displacements and tilts. Subsequently, the numerical method was applied to the experimental data, arriving at a set of coil displacements whose resulting field errors exhibited significantly improved quantitative and qualitative agreement with experimental results.

physics.plasm-ph↗

arXiv2016

Local measurement of error field using naturally rotating tearing mode dynamics in EXTRAP T2R

An error field (EF) detection technique using the amplitude modulation of a naturally rotating tearing mode (TM) is developed and validated in the EXTRAP T2R reversed field pinch. The technique was used to identify intrinsic EFs of $m/n = 1/-12$, where $m$ and $n$ are the poloidal and toroidal mode numbers. The effect of the EF and of a resonant magnetic perturbation (RMP) on the TM, in particular on amplitude modulation, is modeled with a first-order solution of the Modified Rutherford Equation. In the experiment, the TM amplitude is measured as a function of the toroidal angle as the TM rotates rapidly in the presence of an unknown EF and a known, deliberately applied RMP. The RMP amplitude is fixed while the toroidal phase is varied from one discharge to the other, completing a full toroidal scan. Using three such scans with different RMP amplitudes, the EF amplitude and phase are inferred from the phases at which the TM amplitude maximizes. The estimated EF amplitude is consistent with other estimates (e.g. based on the best EF-cancelling RMP, resulting in the fastest TM rotation). A passive variant of this technique is also presented, where no RMPs are applied, and the EF phase is deduced.

physics.plasm-ph↗

arXiv2015

Avoiding Tokamak disruptions by applying static magnetic fields that align locked modes with stabilizing wave-driven currents

Non-rotating (`locked') magnetic islands often lead to complete losses of confinement in tokamak plasmas, called major disruptions. Here locked islands were suppressed for the first time, by a combination of applied three-dimensional magnetic fields and injected millimetre waves. The applied fields were used to control the phase of locking and so align the island O-point with the region where the injected waves generated non-inductive currents. This resulted in stabilization of the locked island, disruption avoidance, recovery of high confinement and high pressure, in accordance with the expected dependencies upon wave power and relative phase between O-point and driven current.

physics.plasm-ph↗

arXiv2015

Conceptual design of first toroidal electron cyclotron resonance ion source and modeling of ion extraction from it

Electron Cyclotron Resonance Ion Sources (ECRIS) progressed to higher and higher ion currents and charge states by adopting stronger magnetic fields (beneficial for confinement) and proportionally higher ECR frequencies. Further improvements would require the attainment of "triple products" of density, temperature and confinement time comparable with major fusion experiments. For this, we propose a new, toroidal rather than linear, ECRIS geometry, which would at the same time improve confinement and make better use of the magnetic field. Ion extraction is more complicated than from a linear device, but feasible, as our modelling suggests: single-particle tracings showed successful extraction by at least two techniques, making use respectively of a magnetic extractor and of ExB drifts. Additional techniques are briefly discussed.

physics.plasm-ph↗

arXiv2014

Metamaterial lens of specifiable frequency-dependent focus and adjustable aperture for electron cyclotron emission in the DIII-D tokamak

Electron Cyclotron Emission (ECE) of different frequencies originates at different locations in non-uniformly magnetized plasmas. For simultaneous observation of multiple ECE frequencies from the outside edge of a toroidal plasma confinement device (e.g. a tokamak), the focal length of the collecting optics should increase with the frequency to maximize the resolution on a line of sight along the magnetic field gradient. Here we present the design and numerical study of a zoned metamaterial lens with such characteristics, for possible deployment with the 83-130 GHz ECE radiometer in the DIII-D tokamak. The lens consists of a concentric array of miniaturized element phase-shifters. These were reverse-engineered starting from the desired Gaussian beam waist locations and further optimized to account for diffraction and finite-aperture effects that tend to displace the waist. At the same time we imposed high and uniform transmittance, averaged over all phase-shifters. The focal length is shown to increase from 1.37 m to 1.97 m over the frequency range of interest, as desired for low-field DIII-D discharges (B = -1.57 T). Retracting the lens to receded positions rigidly moves the waists accordingly, resulting in a good match -within a fraction of the Rayleigh length- of the EC-emitting layer positions at higher fields (up to B = -2.00 T). Further, it is shown how varying the lens aperture might move the waists "non-rigidly" to better match the non-rigid movement of the EC-emitting layers with the magnetic field. The numerical method presented is very general and can be used to engineer any dependence of the focal length on the frequency, including zero or minimal chromatic aberration.

physics.optics↗

arXiv2014

Proto-CIRCUS Tilted-Coil Tokamak-Torsatron Hybrid: Design and Construction

We present the field-line modeling, design and construction of a prototype circular-coil tokamak-torsatron hybrid called Proto-CIRCUS. The device has a major radius R = 16 cm and minor radius a < 5 cm. The six "toroidal field" coils are planar as in a tokamak, but they are tilted. This, combined with induced or driven plasma current, is expected to generate rotational transform, as seen in field-line tracing and equilibrium calculations. The device is expected to operate at lower plasma current than a tokamak of comparable size and magnetic field, which might have interesting implications for disruptions and steady-state operation. Additionally, the toroidal magnetic ripple is less pronounced than in an equivalent tokamak in which the coils are not tilted. The tilted coils are interlocked, resulting in a relatively low aspect ratio, and can be moved, both radially and in tilt angle, between discharges. This capability will be exploited for detailed comparisons between calculations and field-line mapping measurements. Such comparisons will reveal whether this relatively simple concept can generate the expected rotational transform.

physics.plasm-ph↗

arXiv2013

Multi-pole multi-zero frequency-independent phase-shifter

A multi-pole, multi-zero design allowed realizing a "true" phase-shifter (not time-delayer) of flat frequency-response over more than 3 decades (30Hz-100kHz), which can be extended to higher frequencies or broader bands thanks to a modular design. Frequency-dependent optimization of a single resistance made also the gain flat to within few percents. The frequency-independent phase-shifter presented can find application in any experiment in which an action needs to be taken (e.g. a measurement needs to be performed) at a fixed phase-delay relative to an event, regardless of how rapidly the system rotates or oscillates.

physics.ins-det↗

arXiv2013

Error Field Assessment from Driven Rotation of Stable External Kinks at EXTRAP-T2R Reversed Field Pinch

A new non-disruptive error field (EF) assessment technique not restricted to low density and thus low beta was demonstrated at the EXTRAP-T2R reversed field pinch. Stable and marginally stable external kink modes of toroidal mode number n=10 and n=8, respectively, were generated, and their rotation sustained, by means of rotating magnetic perturbations of the same n. Due to finite EFs, and in spite of the applied perturbations rotating uniformly and having constant amplitude, the kink modes were observed to rotate non-uniformly and be modulated in amplitude. This behavior was used to precisely infer the amplitude and approximately estimate the toroidal phase of the EF. A subsequent scan permitted to optimize the toroidal phase. The technique was tested against deliberately applied as well as intrinsic error fields of n=8 and 10. Corrections equal and opposite to the estimated error fields were applied. The efficacy of the error compensation was indicated by the increased discharge duration and more uniform mode rotation in response to a uniformly rotating perturbation. The results are in good agreement with theory, and the extension to lower n, to tearing modes and to tokamaks, including ITER, is discussed.

physics.plasm-ph↗