arXiv subjects
Publications and source records attributed to F. Anulli.
Timing detectors based on extruded scintillators of different dimensions with different kinds of wavelength-shifting fibers read-out through SiPMs have been extensively tested using a cosmic ray telescope. Results in terms of light-yield, time resolutions and longitudinal coordinate resolutions are presented.
We propose a high-precision, fast, robust and cost-effective muon detector concept for an FCC-ee experiment. This design combines precision drift tubes with fast plastic scintillator strips to enable both spatial and timing measurements. The drift tubes deliver two-dimensional position measurements perpendicular to the tubes with a resolution around 100~$\mu$m. Meanwhile, the scintillator strips, read out with the wavelength-shifting fibers and silicon photomultipliers, provide fast timing information with a precision of 200~ps or better and measure the third coordinate along the tubes with a resolution of about 1~mm.
The International Muon Collider Collaboration (IMCC) [1] was established in 2020 following the recommendations of the European Strategy for Particle Physics (ESPP) and the implementation of the European Strategy for Particle Physics-Accelerator R&D Roadmap by the Laboratory Directors Group [2], hereinafter referred to as the the European LDG roadmap. The Muon Collider Study (MuC) covers the accelerator complex, detectors and physics for a future muon collider. In 2023, European Commission support was obtained for a design study of a muon collider (MuCol) [3]. This project started on 1st March 2023, with work-packages aligned with the overall muon collider studies. In preparation of and during the 2021-22 U.S. Snowmass process, the muon collider project parameters, technical studies and physics performance studies were performed and presented in great detail. Recently, the P5 panel [4] in the U.S. recommended a muon collider R&D, proposed to join the IMCC and envisages that the U.S. should prepare to host a muon collider, calling this their "muon shot". In the past, the U.S. Muon Accelerator Programme (MAP) [5] has been instrumental in studies of concepts and technologies for a muon collider.
The investigation of the energy frontier in physics requires novel concepts for future colliders. The idea of a muon collider is very appealing since it would allow to study particle collisions at up to tens of TeV energy, while offering a cleaner experimental environment with respect to hadronic colliders. One key element in the muon collider design is the low-emittance muon production. Recently,the Low EMittance Muon Accelerator (LEMMA) collaboration has explored the muon pair production close to its kinematic threshold by annihilating 45 GeV positrons with electrons in a low Z material target. In this configuration, muons are emerging from the target with a naturally low-emittance. In this paper we describe the performance of a system, to study this production mechanism, that consists in several segmented absorbers with alternating active layers composed of fast Cherenkov detectors together with a muon identification technique based on this detector. Passive layers were made of tungsten. We collected data corresponding to muon and electron beams produced at the H2 line in the North Area of the European Organization for Nuclear Research (CERN) in September 2018.
The muon collider represents one of the most promising solutions for a future machine exploring the high energy frontier, but several challenges due to the 2.2 $μ$sec muon lifetime at rest have to be carefully considered. The LEMMA project is investigating the possibility of producing low emittance muon/antimuon pairs from the e$^+$e$^-$ annihilation process at threshold energy, resulting in small transverse emittance beams without any additional beam cooling. However most of the measurements available are performed at higher $\sqrt{s}$ values. It is therefore necessary to measure muons production in positron annihilation at threshold energy and compare the experimental results with the predictions in this specific energy regime. Apart from being a topic of physical interest by itself, these near to threshold measurements can have a sizeable impact on the estimation of the ultimate luminosity achievable in a muon collider with the LEMMA injection scheme.
The design of a future multi-TeV muon collider needs new ideas to overcome the technological challenges related to muon production, cooling, accumulation and acceleration. In this paper a layout of a positron driven muon source known as the Low EMittance Muon Accelerator (LEMMA) concept is presented. The positron beam, stored in a ring with high energy acceptance and low emittance, is extracted and driven to a multi-target system, to produce muon pairs at threshold. This solution alleviates the issues related to the power deposited and the integrated Peak Energy Density Deposition (PEDD) on the targets. Muons produced in the multi-target system will then be accumulated before acceleration and injection in the collider. A multi-target line lattice has been designed to cope with the focusing of both the positron and muon beams. Studies on the number, material and thickness of the targets have been carried out. A general layout of the overall scheme and a description is presented, as well as plans for future R&D.
A full-size prototype of a Micromegas precision tracking chamber for the upgrade of the ATLAS detector at the LHC Collider has been built between October 2015 and April 2016. This paper describes in detail the procedures used in constructing the single modules of the chamber in various INFN laboratories and the final assembly at the Laboratori Nazionali di Frascati (LNF). Results of the chamber exposure to the CERN SPS/H8 beam line in June 2016 are also presented. The performances achieved in the construction and the results of the test beam are compared with the requirements, which are imposed by the severe environment during the data-taking of the LHC foreseen for the next years.
We report measurements of $\sin{2β}$ and $\cos{2β}$ from a time-dependent Dalitz plot analysis of $B^{0} \to D^{(*)} h^{0}$ with $D \to K_{S}^{0} π^{+} π^{-}$ decays, where the light unflavored and neutral hadron $h^{0}$ is a $π^{0}$, $η$, or $ω$ meson. The analysis is performed with a combination of the final data sets of the \babar\ and Belle experiments containing $471 \times 10^{6}$ and $772 \times 10^{6}$ $B\bar{B}$ pairs collected at the $Υ\left(4S\right)$ resonance at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. We measure $\sin{2β} = 0.80 \pm 0.14 \,(\rm{stat.}) \pm 0.06 \,(\rm{syst.}) \pm 0.03 \,(\rm{model})$ and $\cos{2β} = 0.91 \pm 0.22 \,(\rm{stat.}) \pm 0.09 \,(\rm{syst.}) \pm 0.07 \,(\rm{model})$. The result for the direct measurement of the angle is $β= \left( 22.5 \pm 4.4 \,(\rm{stat.}) \pm 1.2 \,(\rm{syst.}) \pm 0.6 \,(\rm{model}) \right)^{\circ}$. The last quoted uncertainties are due to the composition of the $D^{0} \to K_{S}^{0} π^{+} π^{-}$ decay amplitude model, which is newly established by a Dalitz plot amplitude analysis of a high-statistics $e^{+}e^{-} \to c\bar{c}$ data sample as part of this analysis. We find the first evidence for $\cos2β>0$ at the level of $3.7$ standard deviations. The measurement excludes the trigonometric multifold solution $π/2 - β= (68.1 \pm 0.7)^{\circ}$ at the level of $7.3$ standard deviations and therefore resolves an ambiguity in the determination of the apex of the CKM Unitarity Triangle. The hypothesis of $β= 0^{\circ}$ is ruled out at the level of $5.1$ standard deviations, and thus CP violation is observed in $B^{0} \to D^{(*)} h^{0}$ decays.
We present first evidence that the cosine of the CP-violating weak phase $2β$ is positive, and hence exclude trigonometric multifold solutions of the CKM Unitarity Triangle using a time-dependent Dalitz plot analysis of $B^{0} \to D^{(*)} h^{0}$ with $D \to K_{S}^{0} π^{+} π^{-}$ decays, where $h^{0} \in \{π^{0}, η, ω\}$ denotes a light unflavored and neutral hadron. The measurement is performed combining the final data sets of the BaBar and Belle experiments collected at the $Υ(4S)$ resonance at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. The data samples contain $( 471 \pm 3 )\times 10^6\, B\bar{B}$ pairs recorded by the BaBar detector and $( 772 \pm 11 )\times 10^6\, B\bar{B}$ pairs recorded by the Belle detector. The results of the measurement are $\sin{2β} = 0.80 \pm 0.14 \,(\rm{stat.}) \pm 0.06 \,(\rm{syst.}) \pm 0.03 \,(\rm{model})$ and $\cos{2β} = 0.91 \pm 0.22 \,(\rm{stat.}) \pm 0.09 \,(\rm{syst.}) \pm 0.07 \,(\rm{model})$. The result for the direct measurement of the angle $β$ of the CKM Unitarity Triangle is $β= \left( 22.5 \pm 4.4 \,(\rm{stat.}) \pm 1.2 \,(\rm{syst.}) \pm 0.6 \,(\rm{model}) \right)^{\circ}$. The quoted model uncertainties are due to the composition of the $D^{0} \to K_{S}^{0} π^{+} π^{-}$ decay amplitude model, which is newly established by performing a Dalitz plot amplitude analysis using a high-statistics $e^{+}e^{-} \to c\bar{c}$ data sample. CP violation is observed in $B^{0} \to D^{(*)} h^{0}$ decays at the level of $5.1$ standard deviations. The significance for $\cos{2β}>0$ is $3.7$ standard deviations. The trigonometric multifold solution $π/2 - β= (68.1 \pm 0.7)^{\circ}$ is excluded at the level of $7.3$ standard deviations. The measurement resolves an ambiguity in the determination of the apex of the CKM Unitarity Triangle.
This document collects the proceedings of the "Parton Radiation and Fragmentation from LHC to FCC-ee" workshop (http://indico.cern.ch/e/ee\_jets16) held at CERN in Nov. 2016. The writeup reviews the latest theoretical and experimental developments on parton radiation and parton-hadron fragmentation studies --including analyses of LEP, B-factories, and LHC data-- with a focus on the future perspectives reacheable in $e^+e^-$ measurements at the Future Circular Collider (FCC-ee), with multi-ab$^{-1}$ integrated luminosities yielding 10$^{12}$ and 10$^{8}$ jets from Z and W bosons decays as well as 10$^5$ gluon jets from Higgs boson decays. The main topics discussed are: (i) parton radiation and parton-to-hadron fragmentation functions (splitting functions at NNLO, small-$z$ NNLL resummations, global FF fits including Monte Carlo (MC) and neural-network analyses of the latest Belle/BaBar high-precision data, parton shower MC generators), (ii) jet properties (quark-gluon discrimination, $e^+e^-$ event shapes and multi-jet rates at NNLO+N$^{n}$LL, jet broadening and angularities, jet substructure at small-radius, jet charge determination, $e^+e^-$ jet reconstruction algorithms), (iii) heavy-quark jets (dead cone effect, charm-bottom separation, gluon-to-$b\bar{b}$ splitting), and (iv) non-perturbative QCD phenomena (colour reconnection, baryon and strangeness production, Bose-Einstein and Fermi-Dirac final-state correlations, colour string dynamics: spin effects, helix hadronization).
This work is on the Physics of the B Factories. Part A of this book contains a brief description of the SLAC and KEK B Factories as well as their detectors, BaBar and Belle, and data taking related issues. Part B discusses tools and methods used by the experiments in order to obtain results. The results themselves can be found in Part C. Please note that version 3 on the archive is the auxiliary version of the Physics of the B Factories book. This uses the notation alpha, beta, gamma for the angles of the Unitarity Triangle. The nominal version uses the notation phi_1, phi_2 and phi_3. Please cite this work as Eur. Phys. J. C74 (2014) 3026.
We report a measurement of the time-dependent CP asymmetry of B0->D(*)CP h0 decays, where the light neutral hadron h0 is a pi0, eta or omega meson, and the neutral D meson is reconstructed in the CP eigenstates K+ K-, K0S pi0 or K0S omega. The measurement is performed combining the final data samples collected at the Y(4S) resonance by the BaBar and Belle experiments at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. The data samples contain ( 471 +/- 3 ) x 10^6 BB pairs recorded by the BaBar detector and ( 772 +/- 11 ) x 10^6, BB pairs recorded by the Belle detector. We measure the CP asymmetry parameters -eta_f S = +0.66 +/- 0.10 (stat.) +/- 0.06 (syst.) and C = -0.02 +/- 0.07 (stat.) +/- 0.03 (syst.). These results correspond to the first observation of CP violation in B0->D(*)CP h0 decays. The hypothesis of no mixing-induced CP violation is excluded in these decays at the level of 5.4 standard deviations.
We present the mini-proceedings of the workshop on ``Parton fragmentation in the vacuum and in the medium'' held at the European Centre for Theoretical Studies in Nuclear Physics and Related Areas (ECT*, Trento) in February 2008. The workshop gathered both theorists and experimentalists to discuss the current status of investigations of quark and gluon fragmentation into hadrons at different accelerator facilities (LEP, B-factories, JLab, HERA, RHIC, and Tevatron) as well as preparations for extension of these studies at the LHC. The main physics topics covered were: (i) light-quark and gluon fragmentation in the vacuum including theoretical (global fits analyses and MLLA) and experimental (data from e+e-, p-p, e-p collisions) aspects, (ii) strange and heavy-quark fragmentation, (iii) parton fragmentation in cold QCD matter (nuclear DIS), and (iv) medium-modified fragmentation in hot and dense QCD matter (high-energy nucleus-nucleus collisions). These mini-proceedings consist of an introduction and short summaries of the talks presented at the meeting.
We present a detailed study, done in the framework of the INFN 2006 Roadmap, of the prospects for e+e- physics at the Frascati National Laboratories. The physics case for an e+e- collider running at high luminosity at the phi resonance energy and also reaching a maximum center of mass energy of 2.5 GeV is discussed, together with the specific aspects of a very high luminosity tau-charm factory. Subjects connected to Kaon decay physics are not discussed here, being part of another INFN Roadmap working group. The significance of the project and the impact on INFN are also discussed. All the documentation related to the activities of the working group can be found in http://www.roma1.infn.it/people/bini/roadmap.html.
The status of analysis of processes with hard photon emitted from the initial state (ISR) at BABAR is presented. We tag events by the presence of a hard photon in the detector, then reconstruct mu+mu- and several exclusive hadronic final states. The invariant mass of the final state determines an effective collision center of mass energy at which these measurements can be compared with results from direct e+e- annihilation process. The first results on e+e- --> 2h+2h-, where h=pi,K and on e+e- --> J/psi, obtained with a sample of 89.3/fb, are presented. Measurements of inclusive eta, pi+, K+ and p/anti-p production cross sections below the Y(4S) resonance are also presented. These measurements have nearly complete momentum coverage and precision comparable to the best measurements at higher energies. They therefore allow for precise tests of QCD predictions and fragmentation models at 10.54 GeV and of their scaling properties.