arXiv subjects

F. Glege

Publications and source records attributed to F. Glege.

5 recordsLinked to original sources

arXiv2010

First experience in operating the population of the condition databases for the CMS experiment

Reliable population of the condition databases is critical for the correct operation of the online selection as well as of the offline reconstruction and analysis of data. We will describe here the system put in place in the CMS experiment to populate the database and make condition data promptly available both online for the high-level trigger and offline for reconstruction. The system, designed for high flexibility to cope with very different data sources, uses POOL-ORA technology in order to store data in an object format that best matches the object oriented paradigm for \texttt{C++} programming language used in the CMS offline software. In order to ensure consistency among the various subdetectors, a dedicated package, PopCon (Populator of Condition Objects), is used to store data online. The data are then automatically streamed to the offline database hence immediately accessible offline worldwide. This mechanism was intensively used during 2008 in the test-runs with cosmic rays. The experience of this first months of operation will be discussed in detail.

physics.ins-det↗

arXiv2010

Persistent storage of non-event data in the CMS databases

In the CMS experiment, the non event data needed to set up the detector, or being produced by it, and needed to calibrate the physical responses of the detector itself are stored in ORACLE databases. The large amount of data to be stored, the number of clients involved and the performance requirements make the database system an essential service for the experiment to run. This note describes the CMS condition database architecture, the data-flow and PopCon, the tool built in order to populate the offline databases. Finally, the first experience obtained during the 2008 and 2009 cosmic data taking are presented.

physics.ins-det↗

arXiv2003

The CMS Event Builder

The data acquisition system of the CMS experiment at the Large Hadron Collider will employ an event builder which will combine data from about 500 data sources into full events at an aggregate throughput of 100 GByte/s. Several architectures and switch technologies have been evaluated for the DAQ Technical Design Report by measurements with test benches and by simulation. This paper describes studies of an EVB test-bench based on 64 PCs acting as data sources and data consumers and employing both Gigabit Ethernet and Myrinet technologies as the interconnect. In the case of Ethernet, protocols based on Layer-2 frames and on TCP/IP are evaluated. Results from ongoing studies, including measurements on throughput and scaling are presented. The architecture of the baseline CMS event builder will be outlined. The event builder is organised into two stages with intelligent buffers in between. The first stage contains 64 switches performing a first level of data concentration by building super-fragments from fragments of 8 data sources. The second stage combines the 64 super-fragments into full events. This architecture allows installation of the second stage of the event builder in steps, with the overall throughput scaling linearly with the number of switches in the second stage. Possible implementations of the components of the event builder are discussed and the expected performance of the full event builder is outlined.

physics.ins-det↗

arXiv2003

Run Control and Monitor System for the CMS Experiment

The Run Control and Monitor System (RCMS) of the CMS experiment is the set of hardware and software components responsible for controlling and monitoring the experiment during data-taking. It provides users with a "virtual counting room", enabling them to operate the experiment and to monitor detector status and data quality from any point in the world. This paper describes the architecture of the RCMS with particular emphasis on its scalability through a distributed collection of nodes arranged in a tree-based hierarchy. The current implementation of the architecture in a prototype RCMS used in test beam setups, detector validations and DAQ demonstrators is documented. A discussion of the key technologies used, including Web Services, and the results of tests performed with a 128-node system are presented.

cs.DC↗

arXiv2003

Using XDAQ in Application Scenarios of the CMS Experiment

XDAQ is a generic data acquisition software environment that emerged from a rich set of of use-cases encountered in the CMS experiment. They cover not the deployment for multiple sub-detectors and the operation of different processing and networking equipment as well as a distributed collaboration of users with different needs. The use of the software in various application scenarios demonstrated the viability of the approach. We discuss two applications, the tracker local DAQ system for front-end commissioning and the muon chamber validation system. The description is completed by a brief overview of XDAQ.

hep-ex↗