arXiv subjects

F. Kurth

Publications and source records attributed to F. Kurth.

At least 19 recordsLinked to original sources

arXiv2021

The thermoelectric conversion efficiency problem: Insights from the electron gas thermodynamics close to a phase transition

The bottleneck in modern thermoelectric power generation and cooling is the low energy conversion efficiency of thermoelectric materials. The detrimental effects of lattice phonons on performance can be mitigated, but achieving a high thermoelectric power factor remains a major problem because the Seebeck coefficient and electrical conductivity cannot be jointly increased. The conducting electron gas in thermoelectric materials is the actual working fluid that performs the energy conversion, so its properties determine the maximum efficiency that can theoretically be achieved. By relating the thermoelastic properties of the electronic working fluid to its transport properties (considering noninteracting electron systems), we show why the performance of conventional semiconductor materials is doomed to remain low. Analyzing the temperature dependence of the power factor theoretically in 2D systems and experimentally in a thin film, we find that in the fluctuation regimes of an electronic phase transition, the thermoelectric power factor can significantly increase owing to the increased compressibility of the electron gas. We also calculate the ideal thermoelectric conversion efficiency in noninteracting electron systems across a wide temperature range neglecting phonon effects and dissipative coupling to the heat source and sink. Our results show that driving the electronic system to the vicinity of a phase transition can indeed be an innovative route to strong efficiency enhancement, but at the cost of an extremely narrow temperature range for the use of such materials, which in turn precludes potential development for the desired wide range of thermoelectric energy conversion applications.

cond-mat.mtrl-sci↗

arXiv2017

Selective mass enhancement close to the quantum critical point in BaFe$_2$(As$_{1-x}$P$_x$)$_2$

A quantum critical point (QCP) is currently being conjectured for the BaFe$_2$(As$_{1-x}$P$_x$)$_2$ system at the critical value $x_{\rm c} \approx$ 0.3. In the proximity of a QCP, all thermodynamic and transport properties are expected to scale with a single characteristic energy, given by the quantum fluctuations. Such an universal behavior has not, however, been found in the superconducting upper critical field $H_{\rm c2}$. Here we report $H_{\rm c2}$-data for epitaxial thin films extracted from the electrical resistance measured in very high magnetic fields up to 67 Tesla. Using a multi-band analysis we find that $H_{\rm c2}$ is sensitive to the QCP, implying a significant charge carrier effective mass enhancement at the doping-induced QCP that is essentially band-dependent. Our results point to two qualitatively different groups of electrons in BaFe$_2$(As$_{1-x}$P$_x$)$_2$. The first one (possibly associated to hot spots or whole Fermi sheets) has a strong mass enhancement at the QCP, and the second one is insensitive to the QCP. The observed duality could also be present in many other quantum critical systems.

cond-mat.supr-con↗

arXiv2016

Intrinsic and extrinsic pinning in NdFeAs(O,F): vortex trapping and lock-in by the layered structure

The Fe-based superconductors (FBS) present a large variety of compounds whose properties are affected to different extents by their crystal structures. Amongst them, the $\it{RE}$FeAs(O,F) ($\it{RE}$1111, where $\it{RE}$ is a rare earth element) is the family with the highest critical temperature $T_c$ but also with a large anisotropy and Josephson vortices as demonstrated in the flux-flow regime in Sm1111 ($T_c$ $\sim$ 55 K). Here we focus our attention on the pinning properties of the lower-$T_c$ Nd1111 in the flux-creep regime. We demonstrate that for H//c critical current density $J_c$ at high temperatures is dominated by point-defect pinning centres, whereas at low temperatures surface pinning by planar defects parallel to the $\it{c}$-axis and vortex shearing prevail. When the field approaches the $\it{ab}$-planes, two different regimes are observed at low temperatures as a consequence of the transition between 3D-Abrikosov and 2D-Josephson vortices: one is determined by the formation of a vortex staircase structure and one by lock-in of the vortices parallel to the layers. This is the first study on FBS showing this behaviour in a full temperature, field, and angular range and it demonstrates that, despite the lower $T_c$ and anisotropy of Nd1111 with respect to Sm1111, this compound is substantially affected by intrinsic pinning generating a strong $\it{ab}$-peak in $J_c$.

cond-mat.supr-con↗

arXiv2016

Advanced surface characterization of Ba(Fe$_{0.92}$Co$_{0.08}$)$_2$As$_2$ epitaxial thin films

We report on the systematic characterization of Ba(Fe$_{0.92}$Co$_{0.08}$)$_2$As$_2$ epitaxial thin films on CaF$_2$ substrate in view of their possible use for superconducting electronic applications. By using different and complementary techniques we studied the morphological characteristics of the surface, the structural properties, the magnetic response, and the superconducting properties in terms of critical temperature, critical current, and energy gaps. Particular attention was paid to the homogeneity of the films and to the comparison of their superconducting properties with those of single crystals of the same compound.

cond-mat.supr-con↗

arXiv2015

Unusually high critical current of clean P-doped BaFe2As2 single crystalline thin film

Microstructura lly clean, isov alently P-doped BaFe2As2 (Ba-122) single crystalline thin films have been prepared on MgO (001) substrates by molecular beam epitaxy. These films show a superconducting transition temperature (Tc) of over 30 K although P content is around 0.22, which is lower than the optimal one for single crystals (i.e., 0.33). The enhanced Tc at this doping level is attributed to the in-plane tensile strain. The strained film shows high transport self-field critical current densities (Jc) of over 6 MA/cm2 at 4.2 K, which are among the highest for Fe based superconductors (FeSCs). In-field Jc exceeds 0.1 MA/cm2 at m0H = 35 T for H||ab and m0H = 18 T for H||c at 4.2 K, respectively, in spite of moderate upper critical fields compared to other FeSCs with similar Tc. Structural investigations reveal no defects or misoriented grains pointing to strong pinning centers. We relate this unexpected high Jc to a strong enhancement of the vortex core energy at optimal Tc, driven by in-plane strain and doping. These unusually high Jc make P-doped Ba-122 very favorable for high-field magnet applications.

cond-mat.supr-con↗

arXiv2014

Resistivity in Co-doped Ba-122: comparison of thin films and single crystals

The temperature dependence of the resistivity of epitaxial Ba(Fe_(1-x)Co_x)2As2 thin films (with nominal doping x = 0.08, 0.10 and 0.15) has been analyzed and compared with analogous measurements on single crystals taken from literature. The rho(T) of thin films looks different from that of single crystals, even when the cobalt content is the same. All rho(T) curves can be fitted by considering an effective two-band model (with holes and electrons bands) in which the electrons are more strongly coupled with the bosons (spin fluctuations) than holes, while the effect of impurities is mainly concentrated in the hole band. Within this model the mediating boson has the same characteristic energy in single crystals and thin films, but the shape of the transport spectral function at low energy has to be very different, leading to a "hardening" of the electron-boson spectral function in thin films, associated with the strain induced by the substrate.

cond-mat.supr-con↗

arXiv2014

Investigation of TiO$_x$ barriers for their use in hybrid Josephson and tunnelling junctions based on Ba-122 thin films

We tested oxidized titanium layers as barriers for hybrid Josephson junctions with high $I_cR_n$-products and for the preparation of junctions for tunneling spectroscopy. For that we firstly prepared junctions with conventional superconductor electrodes lead and niobium, respectively. By tuning the barrier thickness we were able to change the junctions' behavior from a Josephson junction to tunnel-like behavior applicable for quasi-particle spectroscopy. Subsequently, we transferred the technology to junctions using Co-doped BaFe$_2$As$_2$ thin films prepared by pulsed laser deposition as base electrode and evaporated Pb as counter electrode. For barriers with a thickness of 1.5\,nm we observe clear Josephson effects with $I_cR_n$\,$\approx$\,90\,$μ$V at 4.2\,K. These junctions behave SNS'-like and are dominated by Andreev reflection transport mechanism. For junctions with barrier thickness of 2.0\,nm and higher no Josephson but SIS'- or SINS'-like behavior with a tunnel-like conductance spectrum was observed.

cond-mat.supr-con↗

arXiv2014

One-dimensional pinning behavior in Co-doped BaFe2As2 thin films

Angle-resolved transport measurements revealed that planar defects dominate flux pinning in the investigated Co-doped BaFe2As2 thin film. For any given field and temperature, the critical current depends only on the angle between the crystallographic c-axis and the applied magnetic field but not on the angle between the current and the field. The critical current is therefore limited only by the in-plane component of the Lorentz force but independent of the out-of-plane component, which is entirely balanced by the pinning force exerted by the planar defects. This one-dimensional pinning behavior shows similarities and differences to intrinsic pinning in layered superconductors.

cond-mat.supr-con↗

arXiv2014

Influence of the spreading resistance on the conductance spectrum of planar hybrid thin film SNS' junctions based on iron pnictides

To investigate the superconducting properties of iron pnictides we prepared planar hybrid SNS' junctions in thin film technology with a pnictide base electrode, a gold barrier layer and a lead counter electrode. Our design allows characterization of the electrodes and the junction independently in a 4-probe method. We show how both electrodes influence the measured spectra due to their spreading resistance. While the Pb electrode has a constant resistance above its $T_c$, the contribution of the pnictide electrode is clearly current-dependent and thus it needs a more advanced method to be corrected. We present an empirical method, which is simple to apply and allows to deal with the spreading resistance in our junctions to recalculate the actual conductance and voltage of one junction at given temperature.

cond-mat.supr-con↗

arXiv2013

Strain induced superconductivity in the parent compound BaFe2As2

The discovery of superconductivity (SC) with a transition temperature, Tc, up to 65K in single-layer FeSe (bulk Tc =8K) films grown on SrTiO3 substrates has attracted special attention to Fe-based thin films. The high Tc is a consequence of the combined effect of electron transfer from the oxygen-vacant substrate to the FeSe thin film and lattice tensile strain. Here we demonstrate the realization of SC in the parent compound BaFe2As2 (no bulk Tc) just by tensile lattice strain without charge doping. We investigate the interplay between strain and SC in epitaxial BaFe2As2 thin films on Fe-buffered MgAl2O4 single crystalline substrates. The strong interfacial bonding between Fe and the FeAs sublattice increases the Fe-Fe distance due to the lattice misfit which leads to a suppression of the antiferromagnetic spin density wave and induces SC with bulk-Tc ?10K. These results highlight the role of structural changes in controlling the phase diagram of Fe-based superconductors.

cond-mat.supr-con↗

arXiv2013

The Effect of 45° Grain Boundaries and associated Fe particles on Jc and resistivity in Ba(Fe0.9Co0.1)2As2 Thin Films

The anisotropy of the critical current density Jc depends in general on both the properties of the flux lines (such as line tension, coherence length and penetration depth) and the properties of the defects (such as density, shape, orientation etc.). Whereas the Jc anisotropy in microstructurally clean films can be scaled to an effective magnetic field containing the Ginzburg-Landau anisotropy term, it is in general not possible (or only in a limited field range) for samples containing extended defects. Here, the Jc anisotropy of a Co-doped BaFe2As2 sample with 45° [001] tilt grain boundaries (GBs), i.e. grain boundaries created by 45° in-plane rotated grains, as well as extended Fe particles is investigated. This microstructure leads to c-axis correlated pinning, both due to the GBs and the Fe particles and manifests in a c-axis peak in the Jc anisotropy at low magnetic fields and a deviation from the anisotropic Ginzburg-Landau scaling at higher fields. Strong pinning at ellipsoidal extended defects, i.e. the Fe particles, is discussed, and the full Jc anisotropy is fitted successfully with the vortex path model. The results are compared to a sample without GBs and Fe particles. 45° GBs seem to be good pinning centers rather than detrimental to current flow.

cond-mat.supr-con↗

arXiv2013

Doping and critical-temperature dependence of the energy gaps in Ba(Fe_{1-x}Co_x)_2As_2 thin films

The dependence of the superconducting gaps in epitaxial Ba(Fe_{1-x}Co_{x})_2As_2 thin films on the nominal doping x (0.04 \leq x \leq 0.15) was studied by means of point-contact Andreev-reflection spectroscopy. The normalized conductance curves were well fitted by using the 2D Blonder-Tinkham-Klapwijk model with two nodeless, isotropic gaps -- although the possible presence of gap anisotropies cannot be completely excluded. The amplitudes of the two gaps Δ_{S} and Δ_{L} show similar monotonic trends as a function of the local critical temperature T_{c}^{A} (measured in the same point contacts) from 25 K down to 8 K. The dependence of the gaps on x is well correlated to the trend of the critical temperature, i.e. to the shape of the superconducting region in the phase diagram. When analyzed within a simple three-band Eliashberg model, this trend turns out to be compatible with a mechanism of superconducting coupling mediated by spin fluctuations, whose characteristic energy scales with T_{c} according to the empirical law Ω_{0}= 4.65*k_{B}*T_{c}, and with a total electron-boson coupling strength λ_{tot}= 2.22 for x \leq 0.10 (i.e. up to optimal doping) that slightly decreases to λ_{tot}= 1.82 in the overdoped samples (x = 0.15).

cond-mat.supr-con↗

arXiv2013

Surface transport properties of Fe-based superconductors: The influence of degradation and inhomogeneity

Surface properties of Co-doped BaFe2As2 epitaxial superconducting thin films were inspected by X-ray photoelectron spectroscopy, scanning spreading resistance microscopy (SSRM), and point contact spectroscopy (PCS). It has been shown that surface of Fe-based superconductors degrades rapidly if being exposed to air, what results in suppression of gap-like structure on PCS spectra. Moreover, SSRM measurements revealed inhomogeneous surface conductivity, what is consistent with strong dependence of PCS spectra on contact position. Presented results suggest that fresh surface and small probing area should be assured for surface sensitive measurements like PCS to obtain intrinsic properties of Fe-based superconductors.

cond-mat.supr-con↗

arXiv2012

Electronic phase diagram of disordered Co doped BaFe2As2

Superconducting and normal state transport properties in iron pnictides are sensitive to disorder and impurity scattering. By investigation of Ba(Fe1-xCox)2As2 thin films with varying Co concentration, we demonstrate that in the dirty limit the superconducting dome in the electronic phase diagram of Ba(Fe1-xCox)2As2 shifts towards lower doping concentrations, which differs significantly from observations in single crystals. We show that especially in the underdoped regime superconducting transition temperatures higher than 27 K are possible.

cond-mat.supr-con↗

arXiv2012

Observation of Multiple Superconducting Gaps in the Infrared Reflectivity Spectra of Ba(Fe0.9Co0.1)2As2

The results of infrared reflectivity measurements for the iron-based high-temperature superconductor Ba(Fe0.9Co0.1)2As2 are reported. The reflectivity is found to be close to unity at frequencies w lower than 2Delta/h (2Delta is the superconducting gap and h is Planck's constant). This is evidence for the s+/- or s+/+ symmetry of the superconducting order parameter in the studied compound. The infrared reflectivity spectra of Ba(Fe0.9Co0.1)2As2 manifest opening of several superconducting gaps at temperatures lower than critical Tc.

cond-mat.supr-con↗

arXiv2011

Planar hybrid superconductor-normal metal-superconductor thin film junctions based on BaFe1.8Co0.2As2

To investigate the transport properties of iron based superconductors, we prepared planar hybrid superconductor-normal metal-superconductor (SNS') thin film junctions with BaFe1.8Co0.2As2 as base electrode. As counter electrode we used a lead indium alloy, while the normal metal layer was formed by thin gold films. Temperature dependent measurements of the electrical conductivity were strongly influenced by the properties of the electrodes. We developed a junction structure that allows us to characterize the electrodes, too, including the behavior of their normal state resistance in order to correct their influences on the conduction spectra. The corrected conductivity of the junction was described within an extended BTK-model and shows a behavior dominated by Andreev reflexion.

cond-mat.supr-con↗

arXiv2010

Influenced of Fe buffer thickness on the crystalline quality and the transport properties of Fe/Ba(Fe1-xCox)2As2 bilayers

The implementation of an Fe buffer layer is a promising way to obtain epitaxial growth of Co-doped BaFe2As2 (Ba-122). However, the crystalline quality and the superconducting properties of Co-doped Ba-122 are influenced by the Fe buffer layer thickness, dFe. The well-textured growth of the Fe/Ba-122 bilayer with dFe = 15 nm results in a high Jc of 0.45 MAcm$^{-2}$ at 12 K in self-field, whereas a low Jc value of 61000 Acm$^{-2}$ is recorded for the bilayer with dFe = 4 nm at the corresponding reduced temperature due to the presence of grain boundaries.

cond-mat.supr-con↗

arXiv2010

Highly anisotropic energy gap in superconducting Ba(Fe$_{0.9}$Co$_{0.1}$)$_{2}$As$_{2}$ from optical conductivity measurements

We have measured the complex dynamical conductivity, $σ= σ_{1} + iσ_{2}$, of superconducting Ba(Fe$_{0.9}$Co$_{0.1}$)$_{2}$As$_{2}$ ($T_{c} = 22$ K) at terahertz frequencies and temperatures 2 - 30 K. In the frequency dependence of $σ_{1}$ below $T_{c}$, we observe clear signatures of the superconducting energy gap opening. The temperature dependence of $σ_{1}$ demonstrates a pronounced coherence peak at frequencies below 15 cm$^{-1}$ (1.8 meV). The temperature dependence of the penetration depth, calculated from $σ_{2}$, shows power-law behavior at the lowest temperatures. Analysis of the conductivity data with a two-gap model, gives the smaller isotropic s-wave gap of $Δ_{A} = 3$ meV, while the larger gap is highly anisotropic with possible nodes and its rms amplitude is $Δ_{0} = 8$ meV. Overall, our results are consistent with a two-band superconductor with an $s_{\pm}$ gap symmetry.

cond-mat.supr-con↗