SearcharxivSearch

arXiv subjects

F. Nati

Publications and source records attributed to F. Nati.

At least 19 recordsLinked to original sources

Proof of concept of the COSMOCal project at the IRAM 30m telescope

This work reports on a test campaign conducted at the IRAM 30m telescope to validate the COSMOCal instrument, a novel concept for absolute calibration of polarization angle, beam properties, and instrumental efficiency. The development is motivated by the stringent calibration requirements of current and next-generation Cosmic Microwave Background (CMB) experiments, whose goal is the precise measurement of CMB polarization. Such measurements are essential to probe fundamental physics, including the possible imprint of primordial inflation. The COSMOCal concept is designed as a space-borne calibration reference intended to provide a stable and absolute polarized signal observable simultaneously by multiple large-aperture ground-based observatories. Prior to any space deployment, a terrestrial prototype was developed and characterized in the laboratory, as reported in Ritacco et al. 2024. The results presented here describe the first validation of the system coupled to an antenna, carried out at the IRAM 30m telescope in September 2024. This campaign aimed at assessing the performance of the full instrument under realistic observational conditions, including its ability to reconstruct polarization observables and interface with a state-of-the-art millimeter-wave polarimeter.

astro-ph.IM

High-accuracy polarimetry for CMB: new frontiers with the POLOCALC project

Modern telescopes observing the Cosmic Microwave Background (CMB) polarization require an exquisite control of systematics to target Inflationary Gravitational Waves (IGW), Cosmic Birefringence (CB), and Primordial Magnetic Fields (PMF). The absolute polarization angle of the detectors is a critical parameter to disentangle the $E$-modes and $B$-modes of the CMB, allowing a correct detection of primordial $B$-modes as well as testing Cosmic Birefringence theories. To this end, we discuss the current status of the POLOCALC project, an ERC Advanced Grant that aims to develop air-borne calibration sources for CMB small-aperture telescopes. The main scientific objective of POLOCALC is to enable a direct calibration of the absolute polarization angle of CMB polarimeters with an accuracy of $0.01 \degree $. We present the latest developments regarding the calibration source, the calibration strategies designed to use drone-based calibrators, and the application to modern ground-based experiments.

astro-ph.CO

Status of the COSmological Microwave Observations CALibrator

As the sensitivity of CMB telescopes increases, the need for precise calibration becomes critical. Started in 2022, the COSMOCal project aims to place an artificial polarized source in geostationary orbit, which will serve as a reference for CMB telescopes. This source will emit at 90, 150 and 270 GHz and will be linearly polarized with a highly precise orientation smaller than 0.1 deg. This proceeding presents the scientific motivations for the project, the current status of the development of the instrument and the results of a calibration campaign performed in March 2026 at the Institut d'Astrophysique Spatiale.

astro-ph.IM

The Atacama Cosmology Telescope: DR6 Sunyaev-Zel'dovich Selected Galaxy Clusters Catalog

We present the results of a search for galaxy clusters in the Atacama Cosmology Telescope (ACT) Data Release 6 (DR6) microwave sky maps covering 16293 square degrees in three frequency bands, using data obtained over the lifetime of the project (2008-2022). We report redshifts and mass estimates for 10040 clusters detected via their Sunyaev-Zel'dovich (SZ) effect with signal-to-noise greater than 4 at a 2.4 arcminute filter scale. The catalog includes 1180 clusters at redshifts greater than 1, and 124 clusters at redshifts greater than 1.5. Using a relation between cluster SZ signal and mass that is consistent with recent weak-lensing measurements, we estimate that clusters detected with signal-to-noise greater than 5 form a sample which is 90% complete for clusters with masses greater than $5 \times 10^{14}$ MSun (measured within a spherical volume with mean density 500 times the critical density). El Gordo, a cluster found in an initial ACT survey of 755 square degrees, remains the most extreme cluster in mass and redshift; we find no cluster with a mass and redshift combination high enough to falsify the standard LCDM cosmology with Gaussian initial perturbations. We make public a variety of data products, including the full cluster candidate list, noise maps, and sky masks, along with our software for cluster detection and instructions for reproducing our cluster catalogs from the public ACT maps.

astro-ph.CO

Measuring the CMB spectral distortions with COSMO: the multi-mode antenna system

In this work, we present the design and manufacturing of the two multi-mode antenna arrays of the COSMO experiment and the preliminary beam pattern measurements of their fundamental mode compared with simulations. COSMO is a cryogenic Martin-Puplett Fourier Transform Spectrometer that aims at measuring the isotropic y-type spectral distortion of the Cosmic Microwave Background from Antarctica, by performing differential measurements between the sky and an internal, cryogenic reference blackbody. To reduce the atmospheric contribution, a spinning wedge mirror performs fast sky-dips at varying elevations while fast, low-noise Kinetic Inductance detectors scan the interferogram. Two arrays of antennas couple the radiation to the detectors. Each array consists of nine smooth-walled multi-mode feed-horns, operating in the $120-180$ GHz and $210-300$ GHz range, respectively. The multi-mode propagation helps increase the instrumental sensitivity without employing large focal planes with hundreds of detectors. The two arrays have a step-linear and a linear profile, respectively, and are obtained by superimposing aluminum plates made with CNC milling. The simulated multi-mode beam pattern has a $\sim 20^{\circ} - 26^{\circ}$ FWHM for the low-frequency array and $\sim 16^{\circ}$ FWHM for the high-frequency one. The side lobes are below $-15$ dB. To characterize the antenna response, we measured the beam pattern of the fundamental mode using a Vector Network Analyzer, in far-field conditions inside an anechoic chamber at room temperature. We completed the measurements of the low-frequency array and found a good agreement with the simulations. We also identified a few non-idealities that we attribute to the measuring setup and will further investigate. A comprehensive multi-mode measurement will be feasible at cryogenic temperature once the full receiver is integrated.

astro-ph.IM

Absolute reference for microwave polarization experiments -- The COSMOCal project and its proof of concept

The cosmic microwave background (CMB), a remnant of the Big Bang, provides unparalleled insights into the primordial universe, its energy content, and the origin of cosmic structures. The success of forthcoming terrestrial and space experiments hinges on meticulously calibrated data. Specifically, the ability to achieve an absolute calibration of the polarization angles with a precision of < 0.1 deg is crucial to identify the signatures of primordial gravitational waves and cosmic birefringence within the CMB polarization. We introduce the COSMOCal project, designed to deploy a polarized source in space for calibrating microwave frequency observations. The project aims to integrate microwave polarization observations from small and large telescopes, ground-based and in space, into a unified scale, enhancing the effectiveness of each observatory and allowing robust combination of data. To demonstrate the feasibility and confirm the observational approach of our project, we developed a prototype instrument that operates in the atmospheric window centered at 260 GHz, specifically tailored for use with the NIKA2 camera at the IRAM 30 m telescope. We present the instrument components and their laboratory characterization. The results of tests performed with the fully assembled prototype using a KIDs-based instrument, similar concept of NIKA2, are also reported. This study paves the way for an observing campaign using the IRAM 30m telescope and contributes to the development of a space-based instrument.

astro-ph.CO

Polarization angle accuracy for future CMB experiments. The COSMOCal project and its prototype in the 1mm band

The Cosmic Microwave Background (CMB) radiation offers a unique window into the early Universe, facilitating precise examinations of fundamental cosmological theories. However, the quest for detecting B-modes in the CMB, predicted by theoretical models of inflation, faces substantial challenges in terms of calibration and foreground modeling. The COSMOCal (COsmic Survey of Millimeter wavelengths Objects for CMB experiments Calibration) project aims at enhancing the accuracy of the absolute calibration of the polarization angle $\psi$ of current and future CMB experiments. The concept includes the build of a very well known artificial source emitting in the frequency range [20-350] GHz that would act as an absolute calibrator for several polarization facilities on Earth. A feasibility study to place the artificial source in geostationary orbit, in the far field for all the telescopes on Earth, is ongoing. In the meanwhile ongoing hardware work is dedicated to build a prototype to test the technology, the precision and the stability of the polarization recovering in the 1 mm band (220-300 GHz). High-resolution experiments as the NIKA2 camera at the IRAM 30m telescope will be deployed for such use. Once carefully calibrated ($\Delta\psi$ < 0.1 degrees) it will be used to observe astrophysical sources such as the Crab nebula, which is the best candidate in the sky for the absolute calibration of CMB experiments.

astro-ph.IM

Measuring the CMB primordial B-modes with Bolometric Interferometry

The Q&U Bolometric Interferometer for Cosmology (QUBIC) is the first bolometric interferometer designed to measure the primordial B-mode polarization of the Cosmic Microwave Background (CMB). Bolometric interferometry is a novel technique that combines the sensitivity of bolometric detectors with the control of systematic effects that is typical of interferometry, both key features in the quest for the faint signal of the primordial B-modes. A unique feature is the so-called "spectral imaging", i.e., the ability to recover the sky signal in several sub-bands within the physical band during data analysis. This feature provides an in-band spectral resolution of \Delta{\nu}/{\nu} \sim 0.04 that is unattainable by a traditional imager. This is a key tool for controlling the Galactic foregrounds contamination. In this paper, we describe the principles of bolometric interferometry, the current status of the QUBIC experiment and future prospects.

astro-ph.CO

Cosmological constraints from the tomography of DES-Y3 galaxies with CMB lensing from ACT DR4

We present a measurement of the cross-correlation between the MagLim galaxies selected from the Dark Energy Survey (DES) first three years of observations (Y3) and cosmic microwave background (CMB) lensing from the Atacama Cosmology Telescope (ACT) Data Release 4 (DR4), reconstructed over $\sim 436$ sq.deg. of the sky. Our galaxy sample, which covers $\sim 4143$ sq.deg., is divided into six redshift bins spanning the redshift range of $0.20<z<1.05$. We adopt a blinding procedure until passing all consistency and systematics tests. After imposing scale cuts for the cross-power spectrum measurement, we reject the null hypothesis of no correlation at 9.1\sigma. We constrain cosmological parameters from a joint analysis of galaxy and CMB lensing-galaxy power spectra considering a flat \LCDM model, marginalized over 23 astrophysical and systematic nuisance parameters. We find the clustering amplitude $S_8\equiv \sigma_8 (\Omega_m/0.3)^{0.5} = 0.75^{+0.04}_{-0.05}$. In addition, we constrain the linear growth of cosmic structure as a function of redshift. Our results are consistent with recent DES Y3 analyses and suggest a preference for a lower $S_8$ compared to results from measurements of CMB anisotropies by the Planck satellite, although at a mild level ($< 2 \sigma$) of statistical significance.

astro-ph.CO

Polarization fraction of Planck Galactic cold clumps and forecasts for the Simons Observatory

We measure the polarization fraction of a sample of $6282$ Galactic cold clumps at $353 \, \mathrm{GHz} $, consisting of $Planck$ Galactic cold clump (PGCC) catalogue category 1 objects (flux densities measured with signal-to-noise ratio $(\mathrm{S/N}) > 4$). We find the mean-squared polarization fraction at $353 \, \mathrm{GHz} $ to be $ \langle \Pi ^ 2 \rangle = [ 4.79 \pm 0.44 ] \times 10 ^ {-4} $ equating to an $ 11 \, \sigma $ detection of polarization. We test if the polarization fraction depends on the clumps' physical properties, including flux density, luminosity, Galactic latitude and physical distance. We see a trend towards increasing polarization fraction with increasing Galactic latitude, but find no evidence that polarization depends on the other tested properties. The Simons Observatory, with an angular resolution of order $1 \, \mathrm{arcmin } $ and noise levels between $22$ and $54$ $ \mu \mathrm{ K-arcmin } $ at high frequencies, will substantially enhance our ability to determine the magnetic field structure in Galactic cold clumps. At $\ge5\,\sigma$ significance, we predict the Simons Observatory will detect at least $\sim12,000$ cold clumps in intensity and $\sim430$ cold clumps in polarization. This number of polarization detections would represent a two orders of magnitude increase over the current $Planck$ results. We also release software that can be used to mask these Galactic cold clumps in other analyses.

astro-ph.GA

Tensor-to-scalar ratio forecasts for extended LiteBIRD frequency configurations

LiteBIRD is a planned JAXA-led CMB B-mode satellite experiment aiming for launch in the late 2020s, with a primary goal of detecting the imprint of primordial inflationary gravitational waves. Its current baseline focal-plane configuration includes 15 frequency bands between 40 and 402 GHz, fulfilling the mission requirements to detect the amplitude of gravitational waves with the total uncertainty on the tensor-to-scalar ratio, $\delta r$, down to $\delta r<0.001$. A key aspect of this performance is accurate astrophysical component separation, and the ability to remove polarized thermal dust emission is particularly important. In this paper we note that the CMB frequency spectrum falls off nearly exponentially above 300 GHz relative to the thermal dust SED, and a relatively minor high frequency extension can therefore result in even lower uncertainties and better model reconstructions. Specifically, we compare the baseline design with five extended configurations, while varying the underlying dust modeling, in each of which the HFT (High-Frequency Telescope) frequency range is shifted logarithmically towards higher frequencies, with an upper cutoff ranging between 400 and 600 GHz. In each case, we measure the tensor-to-scalar ratio $r$ uncertainty and bias using both parametric and minimum-variance component-separation algorithms. When the thermal dust sky model includes a spatially varying spectral index and temperature, we find that the statistical uncertainty on $r$ after foreground cleaning may be reduced by as much as 30--50 % by extending the upper limit of the frequency range from 400 to 600 GHz, with most of the improvement already gained at 500 GHz. We also note that a broader frequency range leads to better ability to discriminate between models through higher $\chi^2$ sensitivity. (abridged)

astro-ph.CO

The Simons Observatory: pipeline comparison and validation for large-scale B-modes

The upcoming Simons Observatory Small Aperture Telescopes aim at achieving a constraint on the primordial tensor-to-scalar ratio $r$ at the level of $\sigma(r=0)\lesssim0.003$, observing the polarized CMB in the presence of partial sky coverage, cosmic variance, inhomogeneous non-white noise, and Galactic foregrounds. We present three different analysis pipelines able to constrain $r$ given the latest available instrument performance, and compare their predictions on a set of sky simulations that allow us to explore a number of Galactic foreground models and elements of instrumental noise, relevant for the Simons Observatory. The three pipelines employ different combinations of parametric and non-parametric component separation at the map and power spectrum levels, and use B-mode purification to estimate the CMB B-mode power spectrum. We applied them to a common set of simulated realistic frequency maps, and compared and validated them with focus on their ability to extract robust constraints on the tensor-to-scalar ratio $r$. We evaluated their performance in terms of bias and statistical uncertainty on this parameter. In most of the scenarios the three methodologies achieve similar performance. Nevertheless, several simulations with complex foreground signals lead to a $>2\sigma$ bias on $r$ if analyzed with the default versions of these pipelines, highlighting the need for more sophisticated pipeline components that marginalize over foreground residuals. We show two such extensions, using power-spectrum-based and map-based methods, that are able to fully reduce the bias on $r$ below the statistical uncertainties in all foreground models explored, at a moderate cost in terms of $\sigma(r)$.

astro-ph.CO

Status of QUBIC, the Q&U Bolometer for Cosmology

The Q&U Bolometric Interferometer for Cosmology (QUBIC) is a novel kind of polarimeter optimized for the measurement of the B-mode polarization of the Cosmic Microwave Back-ground (CMB), which is one of the major challenges of observational cosmology. The signal is expected to be of the order of a few tens of nK, prone to instrumental systematic effects and polluted by various astrophysical foregrounds which can only be controlled through multichroic observations. QUBIC is designed to address these observational issues with a novel approach that combines the advantages of interferometry in terms of control of instrumental systematics with those of bolometric detectors in terms of wide-band, background-limited sensitivity.

astro-ph.IM

Polarization angle requirements for CMB B-mode experiments. Application to the LiteBIRD satellite

A methodology to provide the polarization angle requirements for different sets of detectors, at a given frequency of a CMB polarization experiment, is presented. The uncertainties in the polarization angle of each detector set are related to a given bias on the tensor-to-scalar ratio $r$ parameter. The approach is grounded in using a linear combination of the detector sets to obtain the CMB polarization signal. In addition, assuming that the uncertainties on the polarization angle are in the small angle limit (lower than a few degrees), it is possible to derive analytic expressions to establish the requirements. The methodology also accounts for possible correlations among detectors, that may originate from the optics, wafers, etc. The approach is applied to the LiteBIRD space mission. We show that, for the most restrictive case (i.e., full correlation of the polarization angle systematics among detector sets), the requirements on the polarization angle uncertainties are of around 1 arcmin at the most sensitive frequency bands (i.e., $\approx 150$ GHz) and of few tens of arcmin at the lowest (i.e., $\approx 40$ GHz) and highest (i.e., $\approx 400$ GHz) observational bands. Conversely, for the least restrictive case (i.e., no correlation of the polarization angle systematics among detector sets), the requirements are $\approx 5$ times less restrictive than for the previous scenario. At the global and the telescope levels, polarization angle knowledge of a few arcmins is sufficient for correlated global systematic errors and can be relaxed by a factor of two for fully uncorrelated errors in detector polarization angle. The reported uncertainty levels are needed in order to have the bias on $r$ due to systematics below the limit established by the LiteBIRD collaboration.

astro-ph.CO

Cross-correlation of DES Y3 lensing and ACT/${\it Planck}$ thermal Sunyaev Zel'dovich Effect I: Measurements, systematics tests, and feedback model constraints

We present a tomographic measurement of the cross-correlation between thermal Sunyaev-Zeldovich (tSZ) maps from ${\it Planck}$ and the Atacama Cosmology Telescope (ACT) and weak galaxy lensing shears measured during the first three years of observations of the Dark Energy Survey (DES Y3). This correlation is sensitive to the thermal energy in baryons over a wide redshift range, and is therefore a powerful probe of astrophysical feedback. We detect the correlation at a statistical significance of $21\sigma$, the highest significance to date. We examine the tSZ maps for potential contaminants, including cosmic infrared background (CIB) and radio sources, finding that CIB has a substantial impact on our measurements and must be taken into account in our analysis. We use the cross-correlation measurements to test different feedback models. In particular, we model the tSZ using several different pressure profile models calibrated against hydrodynamical simulations. Our analysis marginalises over redshift uncertainties, shear calibration biases, and intrinsic alignment effects. We also marginalise over $\Omega_{\rm m}$ and $\sigma_8$ using ${\it Planck}$ or DES priors. We find that the data prefers the model with a low amplitude of the pressure profile at small scales, compatible with a scenario with strong AGN feedback and ejection of gas from the inner part of the halos. When using a more flexible model for the shear profile, constraints are weaker, and the data cannot discriminate between different baryonic prescriptions.

astro-ph.CO

Cross-correlation of DES Y3 lensing and ACT/${\it Planck}$ thermal Sunyaev Zel'dovich Effect II: Modeling and constraints on halo pressure profiles

Hot, ionized gas leaves an imprint on the cosmic microwave background via the thermal Sunyaev Zel'dovich (tSZ) effect. The cross-correlation of gravitational lensing (which traces the projected mass) with the tSZ effect (which traces the projected gas pressure) is a powerful probe of the thermal state of ionized baryons throughout the Universe, and is sensitive to effects such as baryonic feedback. In a companion paper (Gatti et al. 2021), we present tomographic measurements and validation tests of the cross-correlation between galaxy shear measurements from the first three years of observations of the Dark Energy Survey, and tSZ measurements from a combination of Atacama Cosmology Telescope and ${\it Planck}$ observations. In this work, we use the same measurements to constrain models for the pressure profiles of halos across a wide range of halo mass and redshift. We find evidence for reduced pressure in low mass halos, consistent with predictions for the effects of feedback from active galactic nuclei. We infer the hydrostatic mass bias ($B \equiv M_{500c}/M_{\rm SZ}$) from our measurements, finding $B = 1.8\pm0.1$ when adopting the ${\it Planck}$-preferred cosmological parameters. We additionally find that our measurements are consistent with a non-zero redshift evolution of $B$, with the correct sign and sufficient magnitude to explain the mass bias necessary to reconcile cluster count measurements with the ${\it Planck}$-preferred cosmology. Our analysis introduces a model for the impact of intrinsic alignments (IA) of galaxy shapes on the shear-tSZ correlation. We show that IA can have a significant impact on these correlations at current noise levels.

astro-ph.CO

Superclustering with the Atacama Cosmology Telescope and Dark Energy Survey: I. Evidence for thermal energy anisotropy using oriented stacking

The cosmic web contains filamentary structure on a wide range of scales. On the largest scales, superclustering aligns multiple galaxy clusters along inter-cluster bridges, visible through their thermal Sunyaev-Zel'dovich signal in the Cosmic Microwave Background. We demonstrate a new, flexible method to analyze the hot gas signal from multi-scale extended structures. We use a Compton-$y$ map from the Atacama Cosmology Telescope (ACT) stacked on redMaPPer cluster positions from the optical Dark Energy Survey (DES). Cutout images from the $y$ map are oriented with large-scale structure information from DES galaxy data such that the superclustering signal is aligned before being overlaid. We find evidence for an extended quadrupole moment of the stacked $y$ signal at the 3.5$\sigma$ level, demonstrating that the large-scale thermal energy surrounding galaxy clusters is anisotropically distributed. We compare our ACT$\times$DES results with the Buzzard simulations, finding broad agreement. Using simulations, we highlight the promise of this novel technique for constraining the evolution of anisotropic, non-Gaussian structure using future combinations of microwave and optical surveys.

astro-ph.CO

The mass and galaxy distribution around SZ-selected clusters

We present measurements of the radial profiles of the mass and galaxy number density around Sunyaev-Zel'dovich-selected clusters using both weak lensing and galaxy counts. The clusters are selected from the Atacama Cosmology Telescope Data Release 5 and the galaxies from the Dark Energy Survey Year 3 dataset. With signal-to-noise of 62 (43) for galaxy (weak lensing) profiles over scales of about $0.2-20h^{-1}$ Mpc, these are the highest precision measurements for SZ-selected clusters to date. Because SZ selection closely approximates mass selection, these measurements enable several tests of theoretical models of the mass and light distribution around clusters. Our main findings are: 1. The splashback feature is detected at a consistent location in both the mass and galaxy profiles and its location is consistent with predictions of cold dark matter N-body simulations. 2. The full mass profile is also consistent with the simulations; hence it can constrain alternative dark matter models that modify the mass distribution of clusters. 3. The shapes of the galaxy and lensing profiles are remarkably similar for our sample over the entire range of scales, from well inside the cluster halo to the quasilinear regime. This can be used to constrain processes such as quenching and tidal disruption that alter the galaxy distribution inside the halo, and scale-dependent features in the transition regime outside the halo. We measure the dependence of the profile shapes on the galaxy sample, redshift and cluster mass. We extend the Diemer \& Kravtsov model for the cluster profiles to the linear regime using perturbation theory and show that it provides a good match to the measured profiles. We also compare the measured profiles to predictions of the standard halo model and simulations that include hydrodynamics. Applications of these results to cluster mass estimation and cosmology are discussed.

astro-ph.CO