arXiv subjects

F. Zhang

Publications and source records attributed to F. Zhang.

At least 55 records · Page 3Linked to original sources

arXiv2019

The High Energy X-ray telescope (HE) onboard the Insight-HXMT astronomy satellite

The Insight-Hard X-ray Modulation Telescope (Insight-HXMT) is a broad band X-ray and gamma-ray (1-3000 keV) astronomy satellite. The High Energy X-ray telescope (HE) is one of its three main telescopes. The main detector plane of HE is composed of 18 NaI(Tl)/CsI(Na) phoswich detectors, where NaI(Tl) serves as primary detector to measure ~ 20-250 keV photons incident from the field of view (FOV) defined by the collimators, and CsI(Na) is used as an active shield detector to NaI(Tl) by pulse shape discrimination. CsI(Na) is also used as an omnidirectional gamma-ray monitor. The HE collimators have a diverse FOV: 1.1°x 5.7° (15 units), 5.7°x 5.7° (2 units) and blocked (1 unit), thus the combined FOV of HE is about 5.7°x 5.7°. Each HE detector has a diameter of 190 mm, resulting in the total geometrical area of about 5100 cm_2. The energy resolution is ~15% at 60 keV. The timing accuracy is better than 10 μs and dead-time for each detector is less than 10 μs. HE is devoted to observe the spectra and temporal variability of X-ray sources in the 20-250 keV band either by pointing observations for known sources or scanning observations to unveil new sources, and to monitor the gamma-ray sky in 0.2-3 MeV. This paper presents the design and performance of the HE instruments. Results of the on-ground calibration experiments are also reported.

astro-ph.IM↗

arXiv2019

The Insight-HXMT mission and its recent progresses

The Hard X-ray Modulation Telescope HXMT or also dubbed as Insight HXMT is China s first astronomical satellite . It was launched on 15 th June 2017 in JiuQuan, China and is currently in service smoothly. It was designed to perform point ing , scan ning and gamma ray burst (GRB) observations and , based on the Direct Demodulation Method (DDM), the image of the scanned sky region can be reconstructed. Here we introduce the mission and its progresses in aspects of payload, core sciences, ground calibration/facility , ground segment, data archive, software, in orbit performance, calibration, background model, observations and preliminary results .

astro-ph.HE↗

arXiv2019

Timing analysis of 2S 1417-624 observed with NICER and Insight-HXMT

We present a study of timing properties of the accreting pulsar 2S 1417-624 observed during its 2018 outburst, based on Swift/BAT, Fermi/GBM, Insight-HXMT and NICER observations. We report a dramatic change of the pulse profiles with luminosity. The morphology of the profile in the range 0.2-10.0keV switches from double to triple peaks at $\sim2.5$ $\rm \times 10^{37}{\it D}_{10}^2\ erg\ s^{-1}$ and from triple to quadruple peaks at $\sim7$ $\rm \times 10^{37}{\it D}_{10}^2\ erg\ s^{-1}$. The profile at high energies (25-100keV) shows significant evolutions as well. We explain this phenomenon according to existing theoretical models. We argue that the first change is related to the transition from the sub to the super-critical accretion regime, while the second to the transition of the accretion disc from the gas-dominated to the radiation pressure-dominated state. Considering the spin-up as well due to the accretion torque, this interpretation allows to estimate the magnetic field self-consistently at $\sim7\times 10^{12}$G.

astro-ph.HE↗

arXiv2019

Constant cyclotron line energy in Hercules X-1 -- Joint Insight-HXMT and NuSTAR observations

The long-term evolution of the centroid energy of the CRSF in Her X-1 is still a mystery. We report a new measurement from a campaign between {\sl Insight}-HXMT and {\sl NuSTAR} performed in February 2018. Generally, the two satellites show well consistent results of timing and spectral properties. The joint spectral analysis confirms that the previously observed long decay phase has ended, and that the line energy instead keeps constant around 37.5 keV after flux correction.

astro-ph.HE↗

arXiv2019

Hot disk of the Swift J0243.6+6124 revealed by Insight-HXMT

We report on analysis of observations of the bright transient X-ray pulsar \src obtained during its 2017-2018 giant outburst with Insight-HXMT, \emph{NuSTAR}, and \textit{Swift} observatories. We focus on the discovery of a sharp state transition of the timing and spectral properties of the source at super-Eddington accretion rates, which we associate with the transition of the accretion disk to a radiation pressure dominated (RPD) state, the first ever directly observed for magnetized neutron star. This transition occurs at slightly higher luminosity compared to already reported transition of the source from sub- to super-critical accretion regime associate with onset of an accretion column. We argue that this scenario can only be realized for comparatively weakly magnetized neutron star, not dissimilar to other ultra-luminous X-ray pulsars (ULPs), which accrete at similar rates. Further evidence for this conclusion is provided by the non-detection of the transition to the propeller state in quiescence which strongly implies compact magnetosphere and thus rules out magnetar-like fields.

astro-ph.HE↗

arXiv2019

In-orbit demonstration of X-ray pulsar navigation with the Insight-HXMT satellite

In this work, we report the in-orbit demonstration of X-ray pulsar navigation with Insight-Hard X-ray Modulation Telescope (Insight-HXMT), which was launched on Jun. 15th, 2017. The new pulsar navigation method 'Significance Enhancement of Pulse-profile with Orbit-dynamics' (SEPO) is adopted to determine the orbit with observations of only one pulsar. In this test, the Crab pulsar is chosen and observed by Insight-HXMT from Aug. 31th to Sept. 5th in 2017. Using the 5-day-long observation data, the orbit of Insight-HXMT is determined successfully with the three telescopes onboard - High Energy X-ray Telescope (HE), Medium Energy X-ray Telescope (ME) and Low Energy X-ray Telescope (LE) - respectively. Combining all the data, the position and velocity of the Insight-HXMT are pinpointed to within 10 km (3 sigma) and 10 m/s (3 sigma), respectively.

astro-ph.IM↗

arXiv2018

Designing plateaued Boolean functions in spectral domain and their classification

The design of plateaued functions over $GF(2)^n$, also known as 3-valued Walsh spectra functions (taking the values from the set $\{0, \pm 2^{\lceil \frac{n+s}{2} \rceil}\}$), has been commonly approached by specifying a suitable algebraic normal form which then induces this particular Walsh spectral characterization. In this article, we consider the reversed design method which specifies these functions in the spectral domain by specifying a suitable allocation of the nonzero spectral values and their signs. We analyze the properties of trivial and nontrivial plateaued functions (as affine inequivalent distinct subclasses), which are distinguished by their Walsh support $S_f$ (the subset of $GF(2)^n$ having the nonzero spectral values) in terms of whether it is an affine subspace or not. The former class exactly corresponds to partially bent functions and admits linear structures, whereas the latter class may contain functions without linear structures. A simple sufficient condition on $S_f$, which ensures the nonexistence of linear structures, is derived and some generic design methods of nontrivial plateaued functions without linear structures are given. The extended affine equivalence of plateaued functions is also addressed using the concept of dual of plateaued functions. Furthermore, we solve the problem of specifying disjoint spectra (non)trivial plateaued functions of maximal cardinality whose concatenation can be used to construct bent functions in a generic manner. This approach may lead to new classes of bent functions due to large variety of possibilities to select underlying duals that define these disjoint spectra plateaued functions. An additional method of specifying affine inequivalent plateaued functions, obtained by applying a nonlinear transform to their input domain, is also given.

cs.IT↗

arXiv2018

In-flight performance of the DAMPE silicon tracker

DAMPE (DArk Matter Particle Explorer) is a spaceborne high-energy cosmic ray and gamma-ray detector, successfully launched in December 2015. It is designed to probe astroparticle physics in the broad energy range from few GeV to 100 TeV. The scientific goals of DAMPE include the identification of possible signatures of Dark Matter annihilation or decay, the study of the origin and propagation mechanisms of cosmic-ray particles, and gamma-ray astronomy. DAMPE consists of four sub-detectors: a plastic scintillator strip detector, a Silicon-Tungsten tracKer-converter (STK), a BGO calorimeter and a neutron detector. The STK is composed of six double layers of single-sided silicon micro-strip detectors interleaved with three layers of tungsten for photon conversions into electron-positron pairs. The STK is a crucial component of DAMPE, allowing to determine the direction of incoming photons, to reconstruct tracks of cosmic rays and to estimate their absolute charge (Z). We present the in-flight performance of the STK based on two years of in-flight DAMPE data, which includes the noise behavior, signal response, thermal and mechanical stability, alignment and position resolution.

astro-ph.IM↗

arXiv2018

Internal alignment and position resolution of the silicon tracker of DAMPE determined with orbit data

The DArk Matter Particle Explorer (DAMPE) is a space-borne particle detector designed to probe electrons and gamma-rays in the few GeV to 10 TeV energy range, as well as cosmic-ray proton and nuclei components between 10 GeV and 100 TeV. The silicon-tungsten tracker-converter is a crucial component of DAMPE. It allows the direction of incoming photons converting into electron-positron pairs to be estimated, and the trajectory and charge (Z) of cosmic-ray particles to be identified. It consists of 768 silicon micro-strip sensors assembled in 6 double layers with a total active area of 6.6 m$^2$. Silicon planes are interleaved with three layers of tungsten plates, resulting in about one radiation length of material in the tracker. Internal alignment parameters of the tracker have been determined on orbit, with non-showering protons and helium nuclei. We describe the alignment procedure and present the position resolution and alignment stability measurements.

physics.ins-det↗

arXiv2017

Observation of Al41Sm5: new evidence for structural hierarchy in Al-Sm alloys

Using an effective genetic algorithm, we uncover the structure of a metastable Al41Sm5 phase that supplements its family sharing similar short-range orders. The phase evolves upon heating an amorphous Al-9.7at.%Sm ribbon, produced by melt-spinning. The dynamical phase selection is discussed with respect to the structural connections between the short-range packing motifs in the amorphous precursor and those observed in the selected phases. The phase elucidated here is one of several newly discovered large-unit-cell phases found to form during devitrification from the glass in this binary system, further illustrating the power and efficiency of our approach, the important role of structural hierarchy in phase selection, and the richness of the metastable phase landscape accessible from the glassy structure.

cond-mat.mtrl-sci↗

arXiv2017

Nucleation of stoichiometric compounds from liquid: the role of the kinetic factor

While the role of the free energy barrier during nucleation is a text-book subject the importance of the kinetic factor is frequently underestimated. We obtained both quantities from molecular dynamics (MD) simulations for the pure Ni and B2 phases in the Ni50Al50 and Cu50Zr50 alloys. The free-energy barrier was found to be higher in Ni but the nucleation rate is much lower in the Ni50Al50 alloy which was attributed to the ordered nature of the B2 phase. Since the Cu50Zr50 B2 phase can has even smaller fraction of the anti-site defects its nucleation is never observed in the MD simulation.

cond-mat.mtrl-sci↗

arXiv2014

Performance of the gas gain monitoring system of the CMS RPC muon detector

The RPC muon detector of the CMS experiment at the LHC (CERN, Geneva, Switzerland) is equipped with a Gas Gain Monitoring (GGM) system. A report on the stability of the system during the 2011-2012 data taking run is given, as well as the observation of an effect which suggests a novel method for the monitoring of gas mixture composition.

physics.ins-det↗

arXiv2014

Proton radiography of magnetic field produced by ultra-intense laser irradiating capacity-coil target

Ultra-intense ultra-short laser is firstly used to irradiate the capacity-coil target to generate magnetic field. The spatial structure and temporal evolution of huge magnetic fields were studied with time-gated proton radiography method. A magnetic flux density of 40T was measured by comparing the proton deflection and particle track simulations. Although the laser pulse duration is only 30fs, the generated magnetic field can last for over 100 picoseconds. The energy conversion efficiency from laser to magnetic field can reach as high as ~20%. The results indicate that tens of tesla (T) magnetic field could be produced in many ultra intense laser facilities around the world, and higher magnetic field could be produced by picosecond lasers.

physics.plasm-ph↗

arXiv2014

Radiation fields by intermediate-age stellar populations with binaries as ionizing sources of H II regions

Radiation fields emitted by O, B-type stars or young stellar populations (SPs) are generally considered as significant central ionizing sources (CISs) of classic H II regions. In our previous studies, we show that the inclusion of binary interactions in stellar population synthesis models can significantly increase the ultraviolet spectrum hardness and the number of ionizing photons of intermediate-age (IA, 7<~log(t/yr)<~8) SPs. In this work, we present photoionization models of H II regions ionized by radiation fields emitted by IA SPs, and show that radiation fields of IA SPs, including binary systems, are in theory possible candidates of significant CISs of classic H II regions. When radiation fields of IA SPs comprising binary systems are used as the CISs of classic H II regions, the theoretical strengths of a number of lines (such as [O III]4959', [S II]6716', etc.), weaker than observations, are raised; the border /selection-criterion lines, between star-forming galaxies and AGNs in the diagnostic diagrams (for example, [N II]6583/Ha~[O III]5007/Hb), move into the region occupied originally by AGNs; and He II 1640 line, observed in Lyman break and high-redshift gravitationally lensed galaxies, also can be produced.

astro-ph.SR↗

arXiv2014

Controllable high-quality electron beam generation by phase slippage effect in layered targets

The bubble structure generated by laser and plasma interactions changes in size depending on the local plasma density. The self injection electrons position with respect to wakefield can be controlled by tailoring the longitudinal plasma density. A regime to enhance the energy of the wakefield accelerated electrons and improve the beam quality is proposed and achieved using layered plasmas with increasing densities. Both the wakefield size and the electron bunch duration are significantly contracted in this regime. The electrons remain in the strong acceleration phase of the wakefield while their energy spread decreases because of their tight spatial distribution. An electron beam of 0.5GeV with less than 0.01 energy spread is obtained through 2.5D PIC simulations.

physics.plasm-ph↗

arXiv2014

The silicon matrix for the prototype for the Dark Matter Particle Explorer

A new generation detector for the high energy cosmic ray - the DAMPE(DArk Matter Particle Explorer) is a satellite based project. Its main object is the measurement of energy spectrum of cosmic ray nuclei from 100GeV to 100TeV, the high energy electrons and gamma ray from 5GeV to 10TeV. A silicon matrix detector described in this paper, is employed for the sea level cosmic ray energy and position detection while the prototype testing of the DAMPE. This matrix is composed by the 180 silicon PIN detectors, which covers an area of 32*20 cm2. The primary testing results are shown including MIPs energy spectrum and the position sensitive map.

physics.ins-det↗

arXiv2013

The impact of binary stars on the colors of high-redshift galaxies

Evolutionary population synthesis (EPS) models play an important role in many studies on the formation and evolution of galaxies. Most EPS models are still poorly calibrated for certain stellar evolution stages, especially for the treatment of binary stars, which are very different from single stars. We aim to present color-magnitude (C-M) and color-color (C-C) relations for passive model galaxies in the redshift z$\sim0.0-3.0$ and to study the effect of binary interactions on these relations for high-redshift passive galaxies. Assuming exponentially declining star formation rate, we used a set of theoretical galaxy templates obtained from Yunnan EPS models (with and without binary interactions) to present the C-M and C-C relations for passive galaxies via Monte Carlo simulation. In Yunnan EPS models with binary interactions, various processes are included, such as mass transfer, mass accretion, common-envelope evolution, collisions, supernova kicks, tidal evolution, and all angular momentum loss mechanisms. In these models, approximately 50 per cent of the stellar systems are binary systems with orbital periods less than 100\,yr. This fraction is a typical value for the Milky Way. We find that the inclusion of binary interactions in the model galaxies' spectra can dramatically alter the predicted C-M and C-C relations and their evolution with redshift. For $z\sim 0.0$ and $1.0$, the binary interactions have a minor effect on the C-M and C-C relations, but at $z\sim 2.0$ and $3.0$ the binary interactions have a major effect on the C-M and C-C relations. Especially for the redshift $z\sim 2.0$, the $g-$band magnitude becomes smaller by $1.5$\,mag, the $g-r$ color becomes bluer by $1.0$\,mag, and the $u-g$ color becomes redder by $1.0$\,mag when binary interactions are included.

astro-ph.GA↗

arXiv2013

Synthetic horizontal branch morphology for different metallicities and ages under tidally enhanced stellar wind

It is believed that, except for metallicity, some other parameters are needed to explain the horizontal branch (HB) morphology of globular clusters (GCs). Furthermore, these parameters are considered to be correlated with the mass loss of the red giant branch (RGB) stars. In our previous work, we proposed that tidally enhanced stellar wind during binary evolution may affect the HB morphology by enhancing the mass loss of the red giant primary. As a further study, we now investigate the effects of metallicity and age on HB morphology by considering tidally enhanced stellar winds during binary evolution. We incorporated the tidally enhanced-stellar-wind model into Eggleton's stellar evolution code to study the binary evolution. To study the effects of metallicity and age on our final results, we conducted two sets of model calculations: (i) for a fixed age, we used three metallicities, namely Z=0.0001, 0.001, and 0.02. (ii) For a fixed metallicity, Z=0.001, we used five ages in our model calculations: 14, 13, 12, 10, and 7 Gyr. We found that HB morphology of GCs becomes bluer with decreasing metallicity, and old GCs present bluer HB morphology than young ones. These results are consistent with previous work. Although the envelope-mass distributions of zero-age HB stars produced by tidally enhanced stellar wind are similar for different metallicities, the synthetic HB under tidally enhanced stellar wind for Z=0.02 presented a distinct gap between red and blue HB. However, this feature was not seen clearly in the synthetic HB for Z=0.001 and 0.0001. We also found that higher binary fractions may make HB morphology become bluer, and we discussed the results with recent observations.

astro-ph.SR↗