arXiv subjects

Faxin Li

Publications and source records attributed to Faxin Li.

15 recordsLinked to original sources

arXiv2022

Elastic, piezoelectric coefficients, and internal frictions of a single alpha-quartz crystal determined by partial-electrode electromechanical impedance spectroscopy

In this work, all the independent elastic coefficients, piezoelectric coefficients, and internal frictions of a single alpha-quartz crystal are determined using our recently proposed partial-electrode electromechanical impedance spectroscopy (PE-EMIS) at 25 centigrade. In PE-EMIS, the rectangular parallelepiped quartz sample with two small partial electrodes fabricated on a corner is self-excited/sensed. The conductance spectrum (equivalent to the resonance spectrum) measured by an impedance analyzer under a true free boundary condition is noiseless, allowing the first 100 eigenmodes ranging from 50 to 310kHz to be accurately fitted. To avoid mode misidentification, the off-plane displacement distributions of the quartz sample under different eigenmodes are determined using a scanned-laser vibrometer. The resonance spectrum measured using a commercial sandwich-like RUS apparatus is also presented for comparison, and the results show that the clamping force in sandwich-like RUS shifts the sample's resonance frequencies, causing 13% and 75% overestimations for the piezoelectric coefficients e11 and e14, respectively. In comparison to the RUS, our proposed PE-EMIS is more effective and convenient, and will be widely used for characterization of piezoelectric crystals.

physics.app-ph↗

arXiv2021

In-plane selective excitation of arbitrary vibration modes using thickness-shear (d15) piezoelectric transducers

Experimental modal analysis (EMA) is of great importance for the dynamic characterization of structures. Existing methods typically employ out-of-plane forces for excitation and measure the acceleration or strain for modal analysis. However, these methods encountered difficulties in some cases. In this work, we proposed an in-plane excitation method based on thickness-shear (d15) piezoelectric transducers. Through the combination of distributed d15 PZT strips, arbitrary vibration modes can be selectively excited in a wide frequency range. Both simulations and experiments were conducted and the results validated the proposed method. Specifically, bending, torsional, and longitudinal vibration modes of a rectangular bar were selectively excited. Torsional modes of a shaft were excited without the aid of brackets and bending modes of a circular plate were excited with actuators placed at nodal lines. Furthermore, the electromechanical impedance of the PZT-structure system was measured from which the natural frequency and quality factor were directly extracted. Due to its simplicity and flexibility, the proposed vibration excitation method is expected to be widely used in near future.

physics.app-ph↗

arXiv2021

Detecting fatigue in aluminum alloys based on internal friction measurement using an electromechanical impedance method

Detecting mechanical fatigue of metallic components is always a challenge in industries. In this work, we proposed to monitor the low-cycle fatigue of a 6061 aluminum alloy based on internal friction (IF) measurement, which is realized by a quantitative electromechanical impedance (Q-EMI) method using a small piezoelectric wafer bonded on the specimen. Large strain amplitude (3.3*10^-3) was employed thus the fatigue life can always be below 10^5 cycles. It was found that except for the initial testing stage, the IF always increases steadily with the increasing fatigue cycles. Before the fatigue failure, the IF can reach 2.5 to 3.4 times of the initial value, which is thought to be caused by the micro-cracks forming and growing. In comparison, the resonance frequency of the specimen just drops less than 2% compared with the initial value. Finally, a general fatigue criterion based on IF measurement is suggested for all the metallic materials.

physics.app-ph↗

arXiv2018

A practical omni-directional SH wave transducer for structural health monitoring based on two thickness-poled piezoelectric half-rings

Structural health monitoring (SHM) has become more and more important in modern industries as it can monitor the safety of structures during the full service life and prevent possible losses of life and economics. Shear horizontal wave in plate-like structures is very useful for long distance defects inspection since its fundamental mode (SH0) is totally non-dispersive. However, all the currently available SH wave transducers are not suitable for practical SHM. In this work, we firstly investigated via finite element simulations the performances of thickness-poled d15 PZT ring based omni-directional SH wave piezoelectric transducers (OSH-PT) consisting of different number of elements. Results show that the two half-rings based OSH-PT can have perfect omni-directivity and acceptable performances in excitation/reception of SH0 waves, and its performances can be fairly enhanced by reducing the outer and inner diameters. Experimental results on a 2mm-thick, 21mm outer-diameter, 9mm inner-diameter two-half-ring OSH-PT shows that it has good omni-directional properties with the maximum deviation of ~14% in both excitation and reception of SH0 wave. The signal to noise ratio (SNR) of the OSH-PT in the case of self-excitation and self-reception is over 15dB from 145kHz to 200kHz, which is acceptable for most applications. The proposed two-half-ring OSH-PT is expected to be widely used in SH0 wave based SHM due to its simple structure, easy fabrication/assembling, low cost and acceptable performances.

physics.app-ph↗

arXiv2017

Giant electrostrain of 0.57% in a periodically orthogonal poled lead titanate zirconate ceramic via reversible domain switching

The widely used ferroelectric ceramics based actuators always suffer from small output strains (typically ~0.1-0.15%). Non-180° domain switching can generate large strain in ferroelectrics but it is usually irreversible. In this work, we tailored the domain structures in a soft lead titanate zirconate (PZT) ceramic by periodically orthogonal poling. The non-180° switching in this domain-engineered PZT ceramics turns to be reversible, resulting in giant electrostrains up to 0.57% under a field of 2kV/mm (dynamic d33*(=S/E) of 2850pm/V). The large electrostrain keeps quite stable and even slightly increases after 10000 cycles of loading, which is very promising for next-generation large-strain actuators.

physics.app-ph↗

arXiv2017

A nearly perfect omnidirectional shear-horizontal (SH) wave transducer based on a thickness poled, thickness-shear (d15) piezoelectric ring

The fundamental shear horizontal (SH0) wave in plates is of great importance in the field of nondestructive testing (NDT) and structural health monitoring (SHM) since it is the unique non-dispersive guided wave mode. For practical applications, a phased array system based on omnidirectional SH0 wave transducers is most useful as it can cover a wide range of a plate. However, so far very few omnidirectional SH wave transducers have been developed. In this work, we proposed an omnidirectional SH piezoelectric transducer (OSH-PT) based on a thickness poled piezoelectric ring. The ring is equally divided into twelve sectors and the electric field is circumferentially applied, resulting in a new thickness-shear (d15) mode. Finite element analysis shows that the proposed OSH-PT can excite single-mode SH0 wave and receive the SH0 wave only. Experiments were then conducted to examine the performance of the proposed OSH-PT. Results indicated that it can generate and receive single-mode SH0 wave in a wide frequency range with nearly uniform sensitivities along all directions. Considering its quite simple configuration, compact size and low cost, the proposed OSH-PT is expected to greatly promote the applications of SH waves in the field of NDT and SHM.

cond-mat.mtrl-sci↗

arXiv2016

An omnidirectional shear horizontal wave transducer based on ring array of face-shear (d24) piezoelectric ceramics

The non-dispersive fundamental shear horizontal (SH0) wave in plate-like structures is of practical importance in non-destructive testing (NDT) and structural health monitoring (SHM). Theoretically, an omnidirectional SH0 transducer phased array system can be used to inspect defects in a large plate in the similar manner to the phased array transducers used in medical B-scan ultrasonics. However, very few omnidirectional SH transducers have been proposed so far. In this work, an omnidirectional SH wave piezoelectric transducer (OSH-PT) was proposed which consists of a ring array of twelve face-shear (d24) trapezoidal PZT elements. Each PZT element can produce face-shear deformation under applied voltage, resulting in circumferential shear deformation in the OSH-PT and omnidirectional SH waves in the hosting plate. Both finite element simulations and experiments were conducted to examine the performance of the proposed OSH-PT. Experimental testing shows that the OSH-PT exhibits good omnidirectional properties, on matter it is used as a SH wave transmitter or a SH wave receiver. This work may greatly promote the applications of SH waves in NDT and SHM.

physics.ins-det↗

arXiv2016

Excitation and reception of pure shear horizontal waves by using face-shear d24 mode piezoelectric wafers

The fundamental shear horizontal (SH0) wave in plate-like structures is of great importance in non-destructive testing (NDT) and structural health monitoring (SHM) as it is non-dispersive, while excitation and reception of SH0 waves using piezoelectrics is always a challenge. In this work, we firstly demonstrate via finite element simulations that face-shear piezoelectrics is superior to thickness-shear piezoelectrics in driving SH waves. Next, by using a newly defined face-shear d24 PZT wafer as actuator and face-shear d36 PMN-PT wafers as sensors, pure SH0 wave was successfully excited in an aluminum plate from 140 kHz to 190 kHz. Then, it was shown that the face-shear d24 PZT wafer could receive the SH0 wave only and filter the Lamb waves over a wide frequency range (120 kHz to 230 kHz). The directionality of the excited SH0 wave was also investigated using face-shear d24 PZT wafers as both actuators and sensors. Results show that pure SH0 wave can be excited symmetrically along two orthogonal directions (0° and 90° ) and the amplitude of the excited SH0 wave can keep over 90% of the maximum amplitude when the deviate angle is within 30°. This work could greatly promote the applications of SH waves in NDT and SHM.

cond-mat.mtrl-sci↗

arXiv2016

Excitation of fundamental shear horizontal wave by using face-shear (d36) piezoelectric ceramics

The fundamental shear horizontal (SH0) wave in plate-like structures is extremely useful for non-destructive testing (NDT) and structural health monitoring (SHM) as it is non-dispersive. However, currently the SH0 wave is usually excited by electromagnetic acoustic transducers (EMAT) whose energy conversion efficiency is fairly low. The face-shear (d36) mode piezoelectrics is more promising for SH0 wave excitation but this mode cannot appear in conventional piezoelectric ceramics. Recently, by modifying the symmetry of poled PbZr1-xTixO3 (PZT) ceramics via ferroelastic domain engineering, we realized the face-shear d36 mode in both soft and hard PZT ceramics. In this work, we further improved the face-shear properties of PZT-4 and PZT-5H ceramics via lateral compression under elevated temperature. It was found that when bonded on a 1 mm-thick aluminum plate, the d36 type PZT-4 exhibited better face-shear performance than PZT-5H. We then successfully excite SH0 wave in the aluminum plate using a face-shear PZT-4 square patch and receive the wave using a face-shear PMN-PT patch. The frequency response and directionality of the excited SH0 wave were also investigated. The SH0 wave can be dominate over the Lamb waves (S0 and A0 waves) from 160 kHz to 280 kHz. The wave amplitude reaches its maxima along the two main directions (0° and 90°). The amplitude can keep over 80% of the maxima when the deviate angle is less than 30°, while it vanishes quickly at the 45° direction. The excited SH0 wave using piezoelectric ceramics could be very promising in the fields of NDT and SHM.

cond-mat.mtrl-sci↗

arXiv2015

Realization of face-shear piezoelectric coefficient d36 in PZT ceramics via ferroelastic domain engineering

The piezoelectric face-shear (d36) mode may be the most useful shear mode in piezoelectrics, while currently this mode can only exist in single crystals of specific point groups and cut directions. Theoretically the d36 coefficient vanishes in piezoelectric ceramics because of its transversally isotropic symmetry . In this work, we modified the symmetry of poled PZT ceramics from transversally isotropic to orthogonal through ferroelastic domain switching by applying a high lateral stress along the "2" direction and holding the stress for several hours. After removing the compression, the piezoelectric coefficient d31 is found much larger than d32. Then by cutting the compressed sample along the zxt+45 deg direction, we realized d36 coefficients up to 206 pC/N which is measured by using a modified d33 meter. The obtained large d36 coefficients in PZT ceramics could be very promising for face-shear mode resonators and shear horizontal (SH) wave generation in nondestructive testing.

cond-mat.mtrl-sci↗

arXiv2014

More ferroelectrics discovered by switching spectroscopy piezoresponse force microscopy?

The local hysteresis loop obtained by switching spectroscopy piezoresponse force microscopy (SS-PFM) is usually regarded as a typical signature of ferroelectric switching. However, such hysteresis loops were also observed in a broad variety of non-ferroelectric materials in the past several years, which casts doubts on the viewpoint that the local hysteresis loops in SS-PFM originate from ferroelectricity. Therefore, it is crucial to explore the mechanism of local hysteresis loops obtained in SS-PFM testing. Here we proposed that non-ferroelectric materials can also exhibit amplitude butterfly loops and phase hysteresis loops in SS-PFM testing due to the Maxwell force as long as the material can show macroscopic D-E hysteresis loops under cyclic electric field loading, no matter what the inherent physical mechanism is. To verify our viewpoint, both the macroscopic D-E and microscopic SS-PFM testing are conducted on a soda-lime glass and a non-ferroelectric dielectric material Ba0.4Sr0.6TiO3. Results show that both materials can exhibit D-E hysteresis loops and SS-PFM phase hysteresis loops, which can well support our viewpoint.

cond-mat.mes-hall↗

arXiv2014

Electric-field-tunable mechanical properties of relaxor ferroelectric single crystal measured by nanoindentation

Electric field dependent mechanical properties of relaxor ferroelectric material Pb(Mn1/3Nb2/3)O3-PbTiO3 are investigated with the nanoindentation technique. Giant electric-field-tunable apparent elastic modulus (up to -39%), hardness (-9% to 20%) and energy dissipation (up to -13%) are reported. Based on experimental data, a characterization method of electromechanical coupled nanoindentation is proposed. In this method, an electric field tunable scaling relationship among elastic modulus, hardness and indentation work for ferroelectric materials can be determined. In addition, this method can be used to obtain the electric-field-dependent elastic modulus and hardness, and avoid the estimate of contact area in the Oliver-Pharr method. Finally, the different effects on elastic modulus between positive and negative electric fields can be explained by the flexoelectric effect.

cond-mat.mes-hall↗

arXiv2013

Multi-field nanoindentation apparatus for measuring local mechanical properties of materials in external magnetic and electric fields

Nano/micro-scale mechanical properties of multiferroic materials can be controlled by the external magnetic or electric field due to the coupling interaction. For the first time, a modularized multi-field nanoindentation apparatus for carrying out testing on materials in external magnetostatic/electrostatic field is constructed. Technical issues, such as the application of magnetic/electric field and the processes to diminish the interference between external fields and the other parts of the apparatus, are addressed. Tests on calibration specimen indicate the feasibility of the apparatus. The load-displacement curves of ferromagnetic, ferroelectric and magnetoelectric materials in the presence/absence of external fields reveal the small-scale magnetomechanical and electromechanical coupling, showing as the Delta-E and Delta-H effects, i.e. the magnetic/electric field induced changes in the apparent elastic modulus and indentation hardness.

physics.ins-det↗

arXiv2012

External uniform electric field removing flexoelectric effect in epitaxial ferroelectric thin films

Using the modified Landau-Ginsburg-Devonshire thermodynamic theory, it is found that the coupling between stress gradient and polarization, or flexoelectricity, has significant effect on ferroelectric properties of epitaxial thin films, such as polarization, free energy profile and hysteresis loop. However, this effect can be completely eliminated by applying an optimized external, uniform electric field. The role of such uniform electric field is shown to be the same as that of an ideal gradient electric field which can suppress the flexoelectricty effect completely based on the present theory. Since the uniform electric field is more convenient to apply and control than gradient electric field, it can be potentially used to remove the flexoelectric effect induced by stress gradient in epitaxial thin films and enhance the ferroelectric properties.

cond-mat.mtrl-sci↗

arXiv2012

Flexoelectricity induced increase of critical thickness in epitaxial ferroelectric thin films

Flexoelectricity describes the coupling between polarization and strain/stress gradients in insulating crystals. In this paper, using the Landau-Ginsburg-Devonshire phenomenological approach, we found that flexoelectricity could increase the theoretical critical thickness in epitaxial BaTiO3 thin films, below which the switchable spontaneous polarization vanishes. This increase is remarkable in tensile films while trivial in compressive films due to the electrostriction caused decrease of potential barrier, which can be easily destroyed by the flexoelectricity, between the ferroelectric state and the paraelectric state in tensile films. In addition, the films are still in a uni-polar state even below the critical thickness due to the flexoelectric effect.

cond-mat.mtrl-sci↗