arXiv subjects

Filip P. Adamus

Publications and source records attributed to Filip P. Adamus.

11 recordsLinked to original sources

arXiv2023

Uniaxial compression of 3D printed samples with voids: laboratory measurements compared with predictions from Effective Medium Theory

3D printing technology offers the possibility of producing synthetic samples with accurately defined microstructures. As indicated by effective medium theory (EMT), the shapes, orientations, and sizes of voids significantly affect the overall elastic response of a solid body. By performing uniaxial compression tests on twenty types of 3D-printed samples containing voids of different geometries, we examine whether the measured effective elasticities are accurately predicted by EMT. To manufacture the sample, we selected printers that use different technologies; fused deposition modelling (FDM), and stereolithography (SLA). We show how printer settings (FDM case) or sample cure time (SLA case) affect the measured properties. We also examine the reproducibility of elasticity tests on identically designed samples. To obtain the range of theoretical predictions, we assume either uniform strain or uniform stress. Our study of over two hundred samples shows that measured effective elastic moduli can fit EMT predictions with an error of less than 5% using both FDM and SLA methods if certain printing specifications and sample design considerations are taken into account. Notably, we find that the pore volume fraction of the designed samples should be above 1% to induce a measurable softening effect, but below 5% to produce accurate EMT estimations that fit the measured elastic properties of the samples. Our results highlight both the strengths of EMT for predicting the effective properties of solids with low pore fraction volume microstructural configurations, and the limitations for high porosity microstructures.

physics.geo-ph↗

arXiv2023

Multi-porous extension of anisotropic poroelasticity: consolidation and related coefficients

We propose the generalisation of the anisotropic poroelasticity theory. At a large scale, a medium is viewed as quasi-static, which is the original assumption of Biot. At a smaller scale, we distinguish different porosity clusters (sets of pores or fractures) that are characterized by various fluid pressures, which is the original poroelastic extension of Aifantis. In consequence, both instantaneous and time-dependent deformation lead to fluid content variations that are different in each cluster. We present the equations for such phenomena, where the anisotropic properties of both the solid matrix and pore sets are assumed. Novel poroelastic coefficients that relate solid and fluid phases in our extension are proposed, and their physical meaning is determined. To demonstrate the utility of our equations and emphasize the meaning of new coefficients, we perform numerical simulations of a triple-porosity consolidation. These simulations reveal positive pore pressure transients in the drained behaviour of weakly connected pore sets, and these may result in mechanical weakening of the material.

physics.geo-ph↗

arXiv2023

Multi-porous extension of anisotropic poroelasticity: linkage with micromechanics

We attempt to formalise the relationship between the poroelasticity theory and the effective medium theory of micromechanics. The assumptions of these two approaches vary, but both can be linked by considering the undrained response of a material; and that is the main focus of the paper. To analyse the linkage between poroelasticity and micromechanics, we do not limit ourselves to the original theory of Biot. Instead, we consider a multi-porous extension of anisotropic poroelasticity, where pore fluid pressure may vary within the bulk medium of interest. As a consequence, any inhomogeneities in the material are not necessarily interconnected; instead, they may form isolated pore sets that are described by different poroelastic parameters and fluid pressures. We attempt to incorporate the effective methods inside Biot-like theory and investigate the poroelastic response of various microstructures. We show the cases where such implementation is valid and the others that appear to be questionable. During micromechanical analysis, we derive a particular case of cylindrical transverse isotropy -- commonly assumed in conventional laboratory triaxial tests -- where the symmetry is induced by sets of aligned cracks.

physics.geo-ph↗

arXiv2021

Effective elasticity of a medium with many parallel fractures

We consider an alternative way of obtaining the effective elastic properties of a cracked medium. Similarly, to the popular linear-slip model, we assume flat, parallel fractures, and long wavelengths. However, we do not treat fractures as weakness planes of displacement discontinuity. In contrast to the classical models, we represent fractures by a thin layer embedded in the background medium. In other words, we follow the Schoenberg-Douma matrix formalism for Backus averaging, but we relax their assumptions of infinite weakness and marginal thickness of a layer so that it does not correspond to the linear-slip plane. To represent the properties of a fracture, we need a fourth order elasticity tensor and a thickness parameter. The effective tensor becomes more complicated, but it may describe a higher concentration of parallel cracks more accurately. Apart from the derivations of the effective elasticity tensors, we perform numerical experiments in which we compare the performance of our approach with a linear-slip model in the context of highly fractured media. Our model becomes pertinent if filled-in cracks occupy more than one percent of the effective medium.

physics.geo-ph↗

arXiv2021

PP-wave reflection coefficient for vertically cracked media: Single set of aligned cracks

The main goal of this paper is to analyse the influence of cracks on the azimuthal variations of amplitude. We restrict our investigation to a single set of vertical, circular, and flat cavities aligned along a horizontal axis. Such cracks are embedded in either isotropic surroundings or transversely isotropic background with a vertical symmetry axis. We employ the effective medium theory to obtain either transversely-isotropic material with a horizontal symmetry axis or an orthotropic medium, respectively. To consider the amplitudes, we focus on a Vavrycuk-Psencik approximation of the PP-wave reflection coefficient. We assume that cracks are situated in one of the halfspaces being in welded contact. Azimuthal variations depend on the background stiffnesses, incidence angle, and crack density parameter. Upon analytical analysis, we indicate which factors (such as background's saturation) cause the reflection coefficient to have maximum absolute value in the direction parallel or perpendicular to cracks. We discuss the irregular cases, where such extreme values appear in the other than the aforementioned directions. Due to the support of numerical simulations, we propose graphic patterns of two-dimensional amplitude variations with azimuth. The patterns consist of a series of shapes that change with the increasing value of the crack density parameter. Schemes appear to differ depending on the incidence angle and the saturation. Finally, we extract these shapes that are characteristic of gas-bearing rocks. They may be treated as gas indicators. We support the findings and verify our patterns using real values of stiffnesses extracted from the sedimentary rocks' samples.

physics.geo-ph↗

arXiv2021

On problematic case of product approximation in Backus average

Elastic anisotropy might be a combined effect of the intrinsic anisotropy and the anisotropy induced by thin-layering. The Backus average, a useful mathematical tool, allows us to describe such an effect quantitatively. The results are meaningful only if the underlying physical assumptions are obeyed, such as static equilibrium of the material. We focus on the only mathematical assumption of the Backus average, namely, product approximation. It states that the average of the product of a varying function with nearly-constant function is approximately equal to the product of the averages of those functions. We discuss particular, problematic case for which the aforementioned assumption is inaccurate. Further, we focus on the seismological context. We examine numerically if the inaccuracy affects the wave propagation in a homogenous medium -- obtained using the Backus average -- equivalent to thin layers. We take into consideration various material symmetries, including orthotropic, cubic, and others. We show that the problematic case of product approximation is strictly related to the negative Poisson's ratio of constituent layers. Therefore, we discuss the laboratory and well-log cases in which such a ratio has been noticed. Upon thorough literature review, it occurs that examples of so-called auxetic materials (media that have negative Poisson's ratio) are not extremely rare exceptions as thought previously. The investigation and derivation of Poisson's ratio for materials exhibiting symmetry classes up to monoclinic become a significant part of this paper. Except for the main objectives, we also show that the averaging of cubic layers results in an equivalent medium with tetragonal (not cubic) symmetry. Additionally, we present concise formulations of stability conditions for low symmetry classes, such as trigonal, orthotropic, and monoclinic.

physics.geo-ph↗

arXiv2020

On effects of inhomogeneity on anisotropy in Backus average

In general, the Backus average of an inhomogeneous stack of isotropic layers is a transversely isotropic medium. Herein, we examine a relation between this inhomogeneity and the strength of resulting anisotropy, and show that, in general, they are proportional to one another. There is an important case, however, in which the Backus average of isotropic layers results in an isotropic -- as opposed to a transversely isotropic -- medium. We show that it is a consequence of the same rigidity of layers, regardless of their compressibility. Thus, in general, the strength of anisotropy of the Backus average increases with the degree of inhomogeneity among layers, except for the case in which all layers exhibit the same rigidity.

physics.geo-ph↗

arXiv2020

On inhomogeneity parameters for Backus average

In this paper, we discuss five parameters that indicate the inhomogeneity of a stack of parallel isotropic layers. We show that, in certain situations, they provide further insight into the intrinsic inhomogeneity of a Backus medium, as compared to the Thomsen parameters. Additionally, we show that the Backus average of isotropic layers is isotropic if and only if $γ=0$. This is in contrast to parameters $δ$ and $ε$, whose zero values do not imply isotropy.

physics.geo-ph↗

arXiv2020

On relationship between trigonal and cubic symmetry classes of an elasticity tensor

In the literature, there is an ambiguity in defining the relationship between trigonal and cubic symmetry classes of an elasticity tensor. We discuss the issue by examining the eigensystems and symmetry groups of trigonal and cubic tensors. Additionally, we present numerical examples indicating that the sole verification of the eigenvalues can lead to confusion in the identification of the elastic symmetry.

physics.class-ph↗

arXiv2019

On constraints imposed on a transversely isotropic elasticity tensor

We discuss several physical constraints imposed on elasticity parameters of a transversely isotropic (TI) tensor. There are three types of restrictions we investigate; a fundamental one of stability conditions, and two additional ones, commonly considered in seismology. The first commonly considered restriction comes from an assumption of a wave with a greater speed in the horizontal than vertical direction. The second constitute the assumption that quasi-P wave is faster than quasi-S waves. We show several numerical examples to examine how these restrictions affect a TI tensor with known values of certain elasticity constants that could be acquired from the vertical or horizontal measurements.

physics.geo-ph↗

arXiv2019

On anisotropy parameters and fluid detection in equivalent TI medium

We consider a long-wave transversely isotropic (TI) medium equivalent to a series of finely parallel-layered isotropic layers, obtained using the \citet{Backus} average. In such a TI equivalent medium, we verify the \citet{Berrymanetal} method of indicating fluids and the author's method \citep{Adamus}, using anisotropy parameter $φ$. Both methods are based on detecting variations of the Lamé parameter, $λ$, in a series of thin isotropic layers, and we treat these variations as potential change of the fluid content. To verify these methods, we use Monte Carlo (MC) simulations; for certain range of Lamé parameters $λ$ and $μ$---relevant to particular type of rocks---we generate numerous combinations of these parameters in thin layers and, after the averaging process, we obtain their TI media counterparts. Subsequently, for each of the aforementioned media, we compute $φ$ and \citet{Thomsen} parameters $ε$ and $δ$. We exhibit $φ$, $ε$ and $δ$ in a form of cross-plots and distributions that are relevant to chosen range of $λ$ and $μ$. We repeat that process for various ranges of Lamé parameters. Additionally, to support the MC simulations, we consider several numerical examples of growing $λ$, by using scale factors. As a result of the thorough analysis of the relations among $φ$, $ε$ and $δ$, we find eleven fluid detectors that compose a new fluid detection method. Based on these detectors, we show the quantified pattern of indicating change of the fluid content.

physics.geo-ph↗