arXiv subjects

Florian Effenberg

Publications and source records attributed to Florian Effenberg.

7 recordsLinked to original sources

arXiv2026

Comparative qualification of advanced plasma-facing materials for fusion pilot plants through public- and private-sector experiments in DIII-D

A coordinated DIII-D campaign exposed and comparatively assessed 44 advanced plasma-facing materials from 12 institutions, including four public-private fusion partnerships, to support fusion pilot plant wall and divertor material down-selection. Samples were exposed using the Divertor Materials Evaluation System (DiMES) under Ohmic, L-mode, and H-mode conditions with edge-localized modes, at 0.2-2.5 MW m$^{-2}$ on flush geometries and 10-15 MW m$^{-2}$ on 10$^{\circ}$ angled geometries. Engineered tungsten architectures retained integrity; long-fiber Wf/W showed the clearest crack-arrest behavior. W-Re and K-doped W showed near-ITER-W-like responses, while additively manufactured W-Ta showed heat-flux-sensitive mass losses of 0.64 mg for the flat sample and 2.19-2.87 mg for angled samples. After irradiation to 0.3 dpa at 550$^{\circ}$C, neutron-irradiated ITER-grade W retained 2.8 times more deuterium than pristine W, while TiB$_2$ showed the lowest D$_2$ release in the Ohmic set. VTaHfMo was the most stable refractory multi-principal-element alloy. NbC and (Nb$_{0.5}$Ta$_{0.5}$)C retained integrity with 0.02-0.03 mg mass loss, whereas ZrC lost 7 mg. CVD SiC retained macroscopic integrity but exhibited an effective Si erosion yield of 0.5, about 5-10 times above prior DIII-D trends. Renewable boron pebble rods underwent controlled recession; 13% of released boron was ionized near the outer strike point and up to 50% was recovered locally. Initial in-situ chromium gross-erosion measurements yielded values of order $10^{-2}$. Together, these results provide cross-material benchmarks for fusion pilot plant down-selection and future AI/ML-assisted plasma-facing-material development.

physics.plasm-ph↗

arXiv2026

First divertor exposure experiments of a renewable boron pebble aggregate in DIII-D

Boron pebble aggregate was tested for the first time as a high-heat-flux granular plasma-facing material in a tokamak divertor. Exposures of up to $q_{\parallel} = \SI{80}{\MW\per\m\squared}$ incident heat flux were conducted in the DIII-D tokamak. Single protruding rods of pebble aggregate composed of sintered amorphous boron pebbles bound with carbon binder were mounted in the Divertor Material Evaluation System (DiMES) sample holders and exposed to L-mode lower single null (LSN) plasmas. Under these heat loads, significant boron dust emission from the boron spheres was observed, and this dust dominates the divertor boron ionization source. Only about half of the released boron was recovered locally as mm-sized particles; with the rest presumably lost mainly as dust into the plasma and vacuum chamber. Preliminary estimates suggest that the rate of surface recession of $\sim$1 cm/s in the pebble conglomerate within the plasma divertor is consistent with the recession rates observed in laser bench tests subjected to normal-incidence heat loads. Although core performance was not adversely affected by the high boron dust emission, future work will need to improve the boron pebble aggregate design to reduce boron dust emission at high heat loads.

physics.plasm-ph↗

arXiv2024

Integrated modeling of boron powder injection for real-time plasma-facing component conditioning

An integrated modeling framework for investigating the application of solid boron powder injection for real-time surface conditioning of plasma-facing components in tokamak environments is presented. Utilizing the DIII-D impurity powder dropper setup, this study simulates B powder injection scenarios ranging from mg/s to tens of mg/s, corresponding to B flux rates of $10^{20}-10^{21}$ B/s in standard L-mode conditions. The comprehensive modeling approach combines EMC3-EIRENE for simulating the D plasma background and DIS for the ablation and transport of the B powder particles. The results show substantial transport of B to the inboard lower divertor, predominantly influenced by the main ion plasma flow. The dependency on powder particle size (5-250 $\mu$m) was found to be insignificant for the scenario considered. The effects of erosion and redeposition were considered to reconcile the discrepancies with experimental observations, which saw substantial deposition on the outer divertor PFCs. For this purpose, the WallDYN3D code was updated to include B sources within the plasma domain and integrated into the modeling framework. The mixed-material migration modeling shows evolving B deposition patterns, suggesting the formation of mixed B-C layers or predominantly B coverage depending on the powder mass flow rate. While the modeling outcomes at lower B injection rates tend to align with experimental observations, the prediction of near-pure B layers at higher rates has yet to be experimentally verified in the C environment of the DIII-D tokamak. The extensive reach of B layers found in the modeling suggests the need for modeling that encompasses the entire wall geometry for more accurate experimental correlations. This integrated approach sets a precedent for analyzing and applying real-time in-situ boron coating techniques in advanced tokamak scenarios, potentially extendable to ITER.

physics.plasm-ph↗

arXiv2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from $3.9-7.5\times10^{19}$ m$^{-3}$ and input powers ranging from $5.5-9$ MW. The small Si pellets were delivered with the impurity granule injector (IGI) at frequencies ranging from 4-16 Hz corresponding to mass flow rates of $5-19$ mg/s ($1-4.2\times10^{20}$ Si/s) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system (DiMES) to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO$_2$ is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least $0.4-1.2$ nm thickness have been deposited at $0.4-0.7$ nm/s. The technique is estimated to coat a surface area of at least 0.94 m$^2$ on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

physics.plasm-ph↗

arXiv2022

Mitigation of plasma-wall interactions with low-Z powders in DIII-D high confinement plasmas

Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in high-confinement mode plasmas ($I_p=$1 MA, $B_t=$2 T, $P_{NB}=$6 MW, $\langle n_e\rangle=3.6-5.0\cdot10^{19}$ m$^{-3}$) into the upper small-angle slot (SAS) divertor for 2-s intervals at constant rates of 3-204 mg/s. The multi-species BN powders at a rate of 54 mg/s showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy $W_{mhd}$ by 5%. Rates of 204 mg/s of boron nitride powder further reduce ELM-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an $n=2$ tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. The results suggest that low-Z powder injection, including mixed element compounds, is a promising new core-edge compatible technique that simultaneously enables divertor detachment and improves wall conditions during high confinement operation.

physics.plasm-ph↗

arXiv2020

Heat and particle flux detachment with stable plasma conditions in the Wendelstein 7-X stellarator fusion experiment

Reduction of particle and heat fluxes to plasma facing components is critical to achieve stable conditions for both the plasma and the plasma material interface in magnetic confinement fusion experiments. A stable and reproducible plasma state in which the heat flux is almost completely removed from the material surfaces was discovered recently in the Wendelstein 7-X stellarator experiment. At the same time also particle fluxes are reduced such that material erosion can be mitigated. Sufficient neutral pressure was reached to maintain stable particle exhaust for density control in this plasma state. This regime could be maintained for up to 28 seconds with a minimum feedback control.

physics.plasm-ph↗

arXiv2019

First Results from an Event Synchronized -- High Repetition Thomson Scattering System at Wendelstein 7-X

The Wendelstein 7-X (W7-X) Thomson scattering (TS) diagnostic was upgraded to transiently achieve kilohertz sampling rates combined with adjustable measuring times. The existing Nd:YAG lasers are employed to repetitively emit "bursts", i.e. multiple laser pulses in a short time interval. Appropriately timing burst in the three available lasers, up to twelve evenly spaced consecutive measurements per burst are possible. The pulse-to-pulse increment within a burst can be tuned from 2 ms to 33.3 ms (500 kHz - 30 Hz). Additionally, an event trigger system was developed to synchronize the burst Thomson scattering measurements to plasma events. Exemplary, a case of fast electron density and temperature evolution after cryogenic H2 pellet injection is presented in order to demonstrate the capabilities of the method.

physics.plasm-ph↗