arXiv subjects

Florian M. Laggner

Publications and source records attributed to Florian M. Laggner.

4 recordsLinked to original sources

arXiv2026

Characterization of ELM Pacing via Vertical Jogs on DIII-D

Edge localized mode (ELM) pacing via vertical plasma oscillations or jogging has been successfully demonstrated on DIII-D. Rapid vertical movement of the plasma toward the X-point has been shown to effectively trigger ELMs. By vertically oscillating the plasma at a rate of 10 Hz, the ELM frequency increased from $\sim$5~Hz, the natural ELM frequency in similar DIII-D discharges, to 10~Hz. Downward jogs have been observed to trigger multiple ELMs in one cycle. ELMs triggered at higher than natural frequencies lead to smaller decreases in stored energy, from ~10\% to as little as below 1\%. As a consequence, the peak heat flux to the divertor has been observed to be reduced by a factor of $\sim$2. In addition, a reduction in the carbon impurity concentration has been observed. During downward jogs in the lower single null (LSN) configuration, the X-point movement is slower and smaller than the top of the plasma. As a result, a reduction in the plasma cross section and hence volume has been observed. To understand the mechanism of ELM triggering by jogging, a toy model of the edge toroidal current has been built and tested with DIII-D experiment data. The experimental data and model suggest that when the plasma moves down towards the X-point, a net positive toroidal current is locally induced in the edge region. ELITE stability analysis suggests that this current pushes the plasma state across the peeling side of the peeling-ballooning stability boundary into the unstable region triggering ELMs.

physics.plasm-ph↗

arXiv2026

Comparative qualification of advanced plasma-facing materials for fusion pilot plants through public- and private-sector experiments in DIII-D

A coordinated DIII-D campaign exposed and comparatively assessed 44 advanced plasma-facing materials from 12 institutions, including four public-private fusion partnerships, to support fusion pilot plant wall and divertor material down-selection. Samples were exposed using the Divertor Materials Evaluation System (DiMES) under Ohmic, L-mode, and H-mode conditions with edge-localized modes, at 0.2-2.5 MW m$^{-2}$ on flush geometries and 10-15 MW m$^{-2}$ on 10$^{\circ}$ angled geometries. Engineered tungsten architectures retained integrity; long-fiber Wf/W showed the clearest crack-arrest behavior. W-Re and K-doped W showed near-ITER-W-like responses, while additively manufactured W-Ta showed heat-flux-sensitive mass losses of 0.64 mg for the flat sample and 2.19-2.87 mg for angled samples. After irradiation to 0.3 dpa at 550$^{\circ}$C, neutron-irradiated ITER-grade W retained 2.8 times more deuterium than pristine W, while TiB$_2$ showed the lowest D$_2$ release in the Ohmic set. VTaHfMo was the most stable refractory multi-principal-element alloy. NbC and (Nb$_{0.5}$Ta$_{0.5}$)C retained integrity with 0.02-0.03 mg mass loss, whereas ZrC lost 7 mg. CVD SiC retained macroscopic integrity but exhibited an effective Si erosion yield of 0.5, about 5-10 times above prior DIII-D trends. Renewable boron pebble rods underwent controlled recession; 13% of released boron was ionized near the outer strike point and up to 50% was recovered locally. Initial in-situ chromium gross-erosion measurements yielded values of order $10^{-2}$. Together, these results provide cross-material benchmarks for fusion pilot plant down-selection and future AI/ML-assisted plasma-facing-material development.

physics.plasm-ph↗

arXiv2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from $3.9-7.5\times10^{19}$ m$^{-3}$ and input powers ranging from $5.5-9$ MW. The small Si pellets were delivered with the impurity granule injector (IGI) at frequencies ranging from 4-16 Hz corresponding to mass flow rates of $5-19$ mg/s ($1-4.2\times10^{20}$ Si/s) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system (DiMES) to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO$_2$ is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least $0.4-1.2$ nm thickness have been deposited at $0.4-0.7$ nm/s. The technique is estimated to coat a surface area of at least 0.94 m$^2$ on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

physics.plasm-ph↗

arXiv2022

Mitigation of plasma-wall interactions with low-Z powders in DIII-D high confinement plasmas

Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in high-confinement mode plasmas ($I_p=$1 MA, $B_t=$2 T, $P_{NB}=$6 MW, $\langle n_e\rangle=3.6-5.0\cdot10^{19}$ m$^{-3}$) into the upper small-angle slot (SAS) divertor for 2-s intervals at constant rates of 3-204 mg/s. The multi-species BN powders at a rate of 54 mg/s showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy $W_{mhd}$ by 5%. Rates of 204 mg/s of boron nitride powder further reduce ELM-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an $n=2$ tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. The results suggest that low-Z powder injection, including mixed element compounds, is a promising new core-edge compatible technique that simultaneously enables divertor detachment and improves wall conditions during high confinement operation.

physics.plasm-ph↗