arXiv subjects

Franz J. Giessibl

Publications and source records attributed to Franz J. Giessibl.

32 records · Page 2Linked to original sources

arXiv2016

Influence of atomic tip structure on the intensity of inelastic tunneling spectroscopy data analyzed by combined scanning tunneling spectroscopy, force microscopy and density functional theory

Achieving a high intensity in inelastic scanning tunneling spectroscopy (IETS) is important for precise measurements. The intensity of the IETS signal can vary up to a factor three for various tips without an apparent reason accessible by scanning tunneling microscopy (STM) alone. Here, we show that combining STM and IETS with atomic force microscopy enables carbon monoxide front atom identification, revealing that high IETS intensities for CO/Cu(111) are obtained for single atom tips, while the intensity drops sharply for multi-atom tips. Adsorbing the CO molecule on a Cu adatom [CO/Cu/Cu(111)] such that it is elevated over the substrate strongly diminishes the tip dependence of IETS intensity, showing that an elevated position channels most of the tunneling current through the CO molecule even for multi-atom tips, while a large fraction of the tunneling current bypasses the CO molecule in the case of CO/Cu(111).

cond-mat.mes-hall↗

arXiv2015

Response of the topological surface state to surface disorder in TlBiSe$_2$

Through a combination of experimental techniques we show that the topmost layer of the topo- logical insulator TlBiSe$_2$ as prepared by cleavage is formed by irregularly shaped Tl islands at cryogenic temperatures and by mobile Tl atoms at room temperature. No trivial surface states are observed in photoemission at low temperatures, which suggests that these islands can not be re- garded as a clear surface termination. The topological surface state is, however, clearly resolved in photoemission experiments. This is interpreted as a direct evidence of its topological self-protection and shows the robust nature of the Dirac cone like surface state. Our results can also help explain the apparent mass acquisition in S-doped TlBiSe$_2$.

cond-mat.mes-hall↗

arXiv2014

CO Tip Functionalization Inverts Atomic Force Microscopy Contrast via Short-Range Electrostatic Forces

We investigated insulating Cu$_2$N islands grown on Cu(100) by means of combined scanning tunneling microscopy and atomic force microscopy with two vastly different tips: a bare metal tip and a CO-terminated tip. We use scanning tunneling microscopy data as proposed by Choi et al. [T. Choi et al., PRB 78, 035430 (2008).] to unambiguously identify atomic positions. Atomic force microscopy images taken with the two different tips show an inverted contrast over Cu$_2$N. The observed force contrast can be explained with an electrostatic model, where the two tips have dipole moments of opposite directions. This highlights the importance of short-range electrostatic forces in the formation of atomic contrast on polar surfaces in non-contact atomic force microscopy.

cond-mat.mes-hall↗

arXiv2014

Chemical and Crystallographic Characterization of the Tip Apex in Scanning Probe Microscopy

The apex atom of a W scanning probe tip reveals a non-spherical charge distribution as probed by a CO molecule bonded to a Cu(111) surface [Welker et al. Science, 336, 444 (2012)]. Three high-symmetry images were observed and related to three low-index crystallographic directions of the W bcc crystal. Open questions remained, however, including the verification that the tip was indeed W-terminated, and whether this method can be easily applied to distinguish other atomic species. In this work, we investigate bulk Cu and Fe tips. In both cases we can associate our data with the fcc (Cu) and bcc (Fe) crystal structures. A model is presented, based on the partial filling of d orbitals, to relate the AFM images to the angular orientation of the tip structure.

cond-mat.mes-hall↗

arXiv2013

Spin Resolution and Evidence for Superexchange on NiO(001) observed by Force Microscopy

The spin order of the nickel oxide (001) surface is resolved, employing non-contact atomic force microscopy at 4.4 K using bulk Fe- and SmCo-tips mounted on a qPlus sensor that oscillates at sub-50 pm amplitudes. The spin-dependent signal is hardly detectable with Fe-tips. In contrast, SmCo-tips yield a height contrast of 1.35 pm for Ni ions with opposite spins. SmCo tips even show a small height contrast on the O atoms of 0.5 pm within the 2x1 spin unit cell, pointing to the observation of superexchange. We attribute this to the increased magnetocrystalline anisotropy energy of SmCo, which stabilizes the magnetic moment at the apex. Atomic force spectroscopy on the Ni up, Ni down and O lattice site reveals a magnitude of the exchange energy of merely 1 meV at the closest accessible distance with an exponential decay length of λ_exc = 18 pm.

cond-mat.mtrl-sci↗

arXiv2013

Optimizing atomic resolution of force microscopy in ambient conditions

Ambient operation poses a challenge to AFM because in contrast to operation in vacuum or liquid environments, the cantilever dynamics change dramatically from oscillating in air to oscillating in a hydration layer when probing the sample. We demonstrate atomic resolution by imaging of the KBr(001) surface in ambient conditions by frequency-modulation atomic force microscopy with a cantilever based on a quartz tuning fork (qPlus sensor) and analyze both long- and short-range contributions to the damping. The thickness of the hydration layer increases with relative humidity, thus varying humidity enables us to study the in uence of the hydration layer thickness on cantilever damping. Starting with measurements of damping versus amplitude, we analyzed the signal and the noise characteristics at the atomic scale. We then determined the optimal amplitude which enabled us to acquire high-quality atomically resolved images.

cond-mat.mes-hall↗

arXiv2012

How local is the Phantom Force?

The phantom force is an apparently repulsive force, which can dominate the atomic contrast of an AFM image when a tunneling current is present. We described this effect with a simple resistive model, in which the tunneling current causes a voltage drop at the sample area underneath the probe tip. Because tunneling is a highly local process, the areal current density is quite high, which leads to an appreciable local voltage drop that in turn changes the electrostatic attraction between tip and sample. However, Si(111)-7\times7 has a metallic surface-state and it might be proposed that electrons should instead propagate along the surface-state, as through a thin metal film on a semiconducting surface, before propagating into the bulk. In this article, we investigate the role of the metallic surface-state on the phantom force. First, we show that the phantom force can be observed on H/Si(100), a surface without a metallic surface-state. Furthermore, we investigate the influence of the surface-state on our phantom force observations of Si(111)-7\times7 by analyzing the influence of the macroscopic tip radius R on the strength of the phantom force, where a noticeable effect would be expected if the local voltage drop would reach extensions comparable to the tip radius. We conclude that a metallic surface-state does not suppress the phantom force, but that the local resistance Rs has a strong effect on the magnitude of the phantom force.

cond-mat.mtrl-sci↗

arXiv2011

Application of the equipartition theorem to the thermal excitation of quartz tuning forks

The deflection signal of a thermally excited force sensor of an atomic force microscope can be analyzed to gain important information about the detector noise and about the validity of the equipartion theorem of thermodynamics. Here, we measured the temperature dependence of the thermal amplitude of a tuning fork and compared it to the expected values based on the equipartition theorem. In doing so, we prove the validity of these assumptions in the temperature range from 140K to 300K. Furthermore, the application of the equipartition theorem to quartz tuning forks at liquid helium temperatures is discussed.

cond-mat.mes-hall↗

arXiv2011

A comparsion of force sensors for atomic force microscopy based on quartz tuning forks and length extensional resonators

The force sensor is key to the performance of atomic force microscopy (AFM). Nowadays, most AFMs use micro-machined force sensors made from silicon, but piezoelectric quartz sensors are applied at an increasing rate, mainly in vacuum. These self sensing force sensors allow a relatively easy upgrade of a scanning tunneling microscope to a combined scanning tunneling/atomic force microscope. Two fundamentally different types of quartz sensors have achieved atomic resolution: the 'needle sensor' that is based on a length extensional resonator and the 'qPlus sensor' that is based on a tuning fork. Here, we calculate and measure the noise characteristics of these sensors. We find four noise sources: deflection detector noise, thermal noise, oscillator noise and thermal drift noise. We calculate the effect of these noise sources as a factor of sensor stiffness, bandwidth and oscillation amplitude. We find that for self sensing quartz sensors, the deflection detector noise is independent of sensor stiffness, while the remaining three noise sources increase strongly with sensor stiffness. Deflection detector noise increases with bandwidth to the power of 1.5, while thermal noise and oscillator noise are proportional to the square root of the bandwidth. Thermal drift noise, however, is inversely proportional to bandwidth. The first three noise sources are inversely proportional to amplitude while thermal drift noise is independent of the amplitude. Thus, we show that the earlier finding that quoted optimal signal-to-noise ratio for oscillation amplitudes similar to the range of the forces is still correct when considering all four frequency noise contributions. Finally, we suggest how the signal-to-noise ratio of the sensors can be further improved and briefly discuss the challenges of mounting tips.

cond-mat.mes-hall↗

arXiv2010

Preparation of light-atom tips for Scanning Probe Microscopy by explosive delamination

To obtain maximal resolution in STM and AFM, the size of the protruding tip orbital has to be minimized. Beryllium as tip material is a promising candidate for enhanced resolution because a beryllium atom has just four electrons, leading to a small covalent radius of only 96 pm. Besides that, beryllium is conductive and has a high elastic modulus, which is a necessity for a stable tip apex. However beryllium tips that are prepared ex situ, are covered with a robust oxide layer, which cannot be removed by just heating the tip. Here we present a successful preparation method that combines the heating of the tip by field emission and a mild collision with a clean metal plate. That method yields a clean, oxide-free tip surface as proven by a work function of as deduced from a current-distance curve. Additionally, a STM image of the Si-(111)-(7x7) is presented to prove the single-atom termination of the beryllium tip.

cond-mat.mes-hall↗

arXiv2005

Electron scattering in atomic force microscopy experiments

It has been shown that electron transitions, as measured in a scanning tunnelling microscope (STM), are related to chemical interactions in a tunnelling barrier. Here, we show that the shape and apparent height of subatomic features in an atomic force microscopy (AFM) experiment on Si(111) depend directly on the available electron states of the silicon surface and the silicon AFM tip. Simulations and experiments confirm that forces and currents show similar subatomic variations for tip-sample distances approaching the bulk bonding length.

cond-mat.mtrl-sci↗

arXiv2005

AFM's path to atomic resolution

We review the progress in the spatial resolution of atomic force microscopy (AFM) in vacuum. After an introduction of the basic principle and a conceptual comparison to scanning tunneling microscopy, the main challenges of AFM and the solutions that have evolved in the first twenty years of its existence are outlined. Some crucial steps along the AFM's path towards higher resolution are discussed, followed by an outlook on current and future applications.

cond-mat.mtrl-sci↗

arXiv2004

Investigating Atomic Details of the CaF$_2$(111) Surface with a qPlus Sensor

The (111) surface of CaF$_2$ has been intensively studied with large-amplitude frequency-modulation atomic force microscopy and atomic contrast formation is now well understood. It has been shown that the apparent contrast patterns obtained with a polar tip strongly depend on the tip terminating ion and three sub-lattices of anions and cations can be imaged. Here, we study the details of atomic contrast formation on CaF$_2$(111) with small-amplitude force microscopy utilizing the qPlus sensor that has been shown to provide utmost resolution at high scanning stability. Step edges resulting from cleaving crystals in-situ in the ultra-high vacuum appear as very sharp structures and on flat terraces, the atomic corrugation is seen in high clarity even for large area scans. The atomic structure is also not lost when scanning across triple layer step edges. High resolution scans of small surface areas yield contrast features of anion- and cation sub-lattices with unprecedented resolution. These contrast patterns are related to previously reported theoretical results.

cond-mat.mtrl-sci↗

arXiv2003

Advances in atomic force microscopy

This article reviews the progress of atomic force microscopy (AFM) in ultra-high vacuum, starting with its invention and covering most of the recent developments. Today, dynamic force microscopy allows to image surfaces of conductors \emph{and} insulators in vacuum with atomic resolution. The mostly used technique for atomic resolution AFM in vacuum is frequency modulation AFM (FM-AFM). This technique, as well as other dynamic AFM methods, are explained in detail in this article. In the last few years many groups have expanded the empirical knowledge and deepened the theoretical understanding of FM-AFM. Consequently, the spatial resolution and ease of use have been increased dramatically. Vacuum AFM opens up new classes of experiments, ranging from imaging of insulators with true atomic resolution to the measurement of forces between individual atoms.

cond-mat.mtrl-sci↗