Searcharxiv⌕ Search

arXiv subjects

G. Bonomi

Publications and source records attributed to G. Bonomi.

At least 19 recordsLinked to original sources
arXiv2025

Sensor operating point calibration and monitoring of the ALICE Inner Tracking System during LHC Run 3

The new Inner Tracking System (ITS2) of the ALICE experiment began operation in 2021 with the start of LHC Run 3. Compared to its predecessor, ITS2 offers substantial improvements in pointing resolution, tracking efficiency at low transverse momenta, and readout-rate capabilities. The detector employs silicon Monolithic Active Pixel Sensors (MAPS) featuring a pixel size of 26.88$\times$29.24 $\mu$m$^2$ and an intrinsic spatial resolution of approximately 5 $\mu$m. With a remarkably low material budget of 0.36% of radiation length ($X_{0}$) per layer in the three innermost layers and a total sensitive area of about 10 m$^2$, the ITS2 constitutes the largest-scale application of MAPS technology in a high-energy physics experiment and the first of its kind operated at the LHC. For stable data taking, it is crucial to calibrate different parameters of the detector, such as in-pixel charge thresholds and the masking of noisy pixels. The calibration of 24120 monolithic sensors, comprising a total of 12.6$\times$10$^{9}$ pixels, represents a major operational challenge. This paper presents the methods developed for the calibration of the ITS2 and outlines the strategies for monitoring and dynamically adjusting the detector's key performance parameters over time.

physics.ins-det↗
arXiv2022

A cryogenic tracking detector for antihydrogen detection in the AEgIS experiment

We present the commissioning of the Fast Annihilation Cryogenic Tracker detector (FACT), installed around the antihydrogen production trap inside the 1 T superconducting magnet of the AEgIS experiment. FACT is designed to detect pions originating from the annihilation of antiprotons. Its 794 scintillating fibers operate at 4 K and are read out by silicon photomultipliers (MPPCs) at near room temperature. FACT provides the antiproton/antihydrogen annihilation position information with a few ns timing resolution. We present the hardware and software developments which led to the successful operation of the detector for antihydrogen detection and the results of an antiproton-loss based efficiency assessment. The main background to the antihydrogen signal is that of the positrons impinging onto the positronium conversion target and creating a large amount of gamma rays which produce a sizeable signal in the MPPCs shortly before the antihydrogen signal is expected. We detail the characterization of this background signal and its impact on the antihydrogen detection efficiency.

physics.ins-det↗
arXiv2022

BLEMAB European project: muon imaging technique applied to blast furnaces

The BLEMAB European project (BLast furnace stack density Estimation through online Muon ABsorption measurements), evolution of the previous MuBlast European project, is designed to investigate in detail the capability of muon radiography techniques applied to the imaging of a blast furnace's inner zone. In particular, the geometry and size of the so called cohesive zone, i.e. the spatial zone where the slowly downward moving material begins to soften and melt, that plays an important role in the performance of the blast furnace itself. Thanks to the high penetration power of the natural cosmic ray muon radiation, muon transmission radiography represents an appropriate non-invasive methodology for imaging large high-density structures such as blast furnaces, whose linear size can be up to a few tens of meters. A state-of-the-art muon tracking system, whose design profits from the long experience of our collaboration in this field, is currently under development and will be installed in 2022 at a blast furnace on the ArcelorMittal site in Bremen (Germany) for many months. Collected data will be exploited to monitor temporal variations of the average density distribution inside the furnace. Muon radiography results will also be compared with measurements obtained through an enhanced multipoint probe and standard blast furnace models.

physics.ins-det↗
arXiv2021

First demonstration of in-beam performance of bent Monolithic Active Pixel Sensors

A novel approach for designing the next generation of vertex detectors foresees to employ wafer-scale sensors that can be bent to truly cylindrical geometries after thinning them to thicknesses of 20-40$μ$m. To solidify this concept, the feasibility of operating bent MAPS was demonstrated using 1.5$\times$3cm ALPIDE chips. Already with their thickness of 50$μ$m, they can be successfully bent to radii of about 2cm without any signs of mechanical or electrical damage. During a subsequent characterisation using a 5.4GeV electron beam, it was further confirmed that they preserve their full electrical functionality as well as particle detection performance. In this article, the bending procedure and the setup used for characterisation are detailed. Furthermore, the analysis of the beam test, including the measurement of the detection efficiency as a function of beam position and local inclination angle, is discussed. The results show that the sensors maintain their excellent performance after bending to radii of 2cm, with detection efficiencies above 99.9% at typical operating conditions, paving the way towards a new class of detectors with unprecedented low material budget and ideal geometrical properties.

physics.ins-det↗
arXiv2019

Efficient $2^3S$ positronium production by stimulated decay from the $3^3P$ level

We investigate experimentally the possibility of enhancing the production of $2^3S$ positronium atoms by driving the $1^3S$-$3^3P$ and $3^3P$-$2^3S$ transitions, overcoming the natural branching ratio limitation of spontaneous decay from $3^3P$ to $2^3S$. The decay of $3^3P$ positronium atoms towards the $2^3S$ level has been effciently stimulated by a 1312.2nm broadband IR laser pulse. The dependence of the stimulating transition efficiency on the intensity of the IR pulse has been measured to find the optimal enhancement conditions. A maximum relative increase of $ \times (3.1 \pm 1.0) $ in the $2^3S$ production efficiency, with respect to the case where only spontaneous decay is present, was obtained.

physics.atom-ph↗
arXiv2019

Velocity selected production of $2^3S$ metastable positronium

Positronium in the $2^3S$ metastable state exhibits a low electrical polarizability and a long lifetime (1140 ns) making it a promising candidate for interferometry experiments with a neutral matter-antimatter system. In the present work, $2^3S$ positronium is produced - in absence of electric field - via spontaneous radiative decay from the $3^3P$ level populated with a 205nm UV laser pulse. Thanks to the short temporal length of the pulse, 1.5 ns full-width at half maximum, different velocity populations of a positronium cloud emitted from a nanochannelled positron/positronium converter were selected by delaying the excitation pulse with respect to the production instant. $ 2^3S $ positronium atoms with velocity tuned between $ 7 \cdot 10^4 $ m/s and $ 10 \cdot 10^4 $ m/s were thus produced. Depending on the selected velocity, a $2^3S$ production effciency ranging from $\sim 0.8 \%$ to $\sim 1.7%$, with respect to the total amount of emitted positronium, was obtained. The observed results give a branching ratio for the $3^3P$-$2^3S$ spontaneous decay of $(9.7 \pm 2.7) \% $. The present velocity selection technique could allow to produce an almost monochromatic beam of $\sim 1 \cdot 10^3 $ $2^3S$ atoms with a velocity spread $ < 10^4 $ m/s and an angular divergence of $\sim$ 50 mrad.

physics.atom-ph↗
arXiv2018

Producing long-lived $2^3\text{S}$ Ps via $3^3\text{P}$ laser excitation in magnetic and electric fields

Producing positronium (Ps) in the metastable $2^3\text{S}$ state is of interest for various applications in fundamental physics. We report here about an experiment in which Ps atoms are produced in this long-lived state by spontaneous radiative decay of Ps excited to the $3^3\text{P}$ level manifold. The Ps cloud excitation is obtained with a UV laser pulse in an experimental vacuum chamber in presence of guiding magnetic field of 25 mT and an average electric field of 300 V/cm. The indication of the $2^3\text{S}$ state production is obtained from a novel analysis technique of single-shot positronium annihilation lifetime spectra. Its production efficiency relative to the total amount of formed Ps is evaluated by fitting a simple rate equations model to the experimental data and found to be $ (2.1 \pm 1.3) \, \% $.

physics.atom-ph↗
arXiv2017

Measurement of antiproton annihilation on Cu, Ag and Au with emulsion films

The characteristics of low energy antiproton annihilations on nuclei (e.g. hadronization and product multiplicities) are not well known, and Monte Carlo simulation packages that use different models provide different descriptions of the annihilation events. In this study, we measured the particle multiplicities resulting from antiproton annihilations on nuclei. The results were compared with predictions obtained using different models in the simulation tools GEANT4 and FLUKA. For this study, we exposed thin targets (Cu, Ag and Au) to a very low energy antiproton beam from CERN's Antiproton Decelerator, exploiting the secondary beamline available in the AEgIS experimental zone. The antiproton annihilation products were detected using emulsion films developed at the Laboratory of High Energy Physics in Bern, where they were analysed at the automatic microscope facility. The fragment multiplicity measured in this study is in good agreement with results obtained with FLUKA simulations for both minimally and heavily ionizing particles.

hep-ex↗
arXiv2016

Precision measurements of Linear Scattering Density using Muon Tomography

We demonstrate that muon tomography can be used to precisely measure the properties of various materials. The materials which have been considered have been extracted from an experimental blast furnace, including carbon (coke) and iron oxides, for which measurements of the linear scattering density relative to the mass density have been performed with an absolute precision of 10%. We report the procedures that are used in order to obtain such precision, and a discussion is presented to address the expected performance of the technique when applied to heavier materials. The results we obtain do not depend on the specific type of material considered and therefore they can be extended to any application.

physics.ins-det↗
arXiv2015

$Σ^- p$ emission rates in $K^-$ absorptions at rest on $^6$Li, $^7$Li, $^{9}$Be, $^{13}$C and $^{16}$O

An experimental study of the $K^-_{stop}A\rightarrow Σ^- p A'$ reaction on $A=^6$Li, $^7$Li, $^9$Be, $^{13}$C and $^{16}$O $p$-shell nuclei is presented. The data were collected by the FINUDA spectrometer operating at the DA$Φ$NE $ϕ$-factory (LNF-INFN, Italy). Emission rates for the reaction in the mentioned nuclei are measured and compared with the few existing data. The spectra of several observables are discussed; indications of Quasi-Free absorptions by a $(np)$ pair embedded in the $A$ nucleus can be obtained from the study of the missing mass distributions.

nucl-ex↗
arXiv2014

First determination of the one-proton induced Non-Mesonic Weak Decay width of p-shell Λ-Hypernuclei

Previous studies of proton and neutron spectra from Non-Mesonic Weak Decay of eight Lambda-Hypernuclei (A = 5-16) have been revisited. New values of the ratio of the two-nucleon and the one-proton induced decay widths, Gamma_2N/Gamma_p, are obtained from single proton spectra, Gamma_2N/Gamma_p = 0.50 +/- 0.24, and from neutron and proton coincidence spectra, Gamma_2N/Gamma_p = 0.36 +/- 0.14stat +0.05sys -0.04sys , in full agreement with previously published ones. With these values, a method is developed to extract the one-proton induced decay width in units of the free Lambda decay width, Gamma_p/Gamma_Lambda, without resorting to Intra Nuclear Cascade models but by exploiting only experimental data, under the assumption of a linear dependence on A of the Final State Interaction contribution. This is the first systematic determination ever done and it agrees within the errors with recent theoretical calculations.

nucl-ex↗
arXiv2014

Annihilation of low energy antiprotons in silicon

The goal of the AE$\mathrm{\bar{g}}$IS experiment at the Antiproton Decelerator (AD) at CERN, is to measure directly the Earth's gravitational acceleration on antimatter. To achieve this goal, the AE$\mathrm{\bar{g}}$IS collaboration will produce a pulsed, cold (100 mK) antihydrogen beam with a velocity of a few 100 m/s and measure the magnitude of the vertical deflection of the beam from a straight path. The final position of the falling antihydrogen will be detected by a position sensitive detector. This detector will consist of an active silicon part, where the annihilations take place, followed by an emulsion part. Together, they allow to achieve 1$%$ precision on the measurement of $\bar{g}$ with about 600 reconstructed and time tagged annihilations. We present here, to the best of our knowledge, the first direct measurement of antiproton annihilation in a segmented silicon sensor, the first step towards designing a position sensitive silicon detector for the AE$\mathrm{\bar{g}}$IS experiment. We also present a first comparison with Monte Carlo simulations (GEANT4) for antiproton energies below 5 MeV

physics.ins-det↗
arXiv2014

Historical building stability monitoring by means of a cosmic ray tracking system

Cosmic ray radiation is mostly composed, at sea level, by high energy muons, which are highly penetrating particles capable of crossing kilometers of rock. Cosmic ray radiation constituted the first source of projectiles used to investigate the intimate structure of matter and is currently and largely used for particle detector test and calibration. The ubiquitous and steady presence at the Earth's surface and the high penetration capability has motivated the use of cosmic ray radiation also in fields beyond particle physics, from geological and archaeological studies to industrial applications and civil security. In the present paper, cosmic ray muon detection techniques are assessed for stability monitoring applications in the field of civil engineering, in particular for static monitoring of historical buildings, where conservation constraints are more severe and the time evolution of the deformation phenomena under study may be of the order of months or years. As a significant case study, the monitoring of the wooden vaulted roof of the "Palazzo della Loggia" in the town of Brescia, in Italy, has been considered. The feasibility as well as the performances and limitations of a monitoring system based on cosmic ray tracking, in the considered case, have been studied by Monte Carlo simulation and discussed in comparison with more traditional monitoring systems. Requirements for muon detectors suitable for this particular application, as well as the results of some preliminary tests on a muon detector prototype based on scintillating fibers and silicon photomultipliers SiPM are presented.

physics.ins-det↗
arXiv2013

Noise reduction in muon tomography for detecting high density objects

The muon tomography technique, based on multiple Coulomb scattering of cosmic ray muons, has been proposed as a tool to detect the presence of high density objects inside closed volumes. In this paper a new and innovative method is presented to handle the density fluctuations (noise) of reconstructed images, a well known problem of this technique. The effectiveness of our method is evaluated using experimental data obtained with a muon tomography prototype located at the Legnaro National Laboratories (LNL) of the Istituto Nazionale di Fisica Nucleare (INFN). The results reported in this paper, obtained with real cosmic ray data, show that with appropriate image filtering and muon momentum classification, the muon tomography technique can detect high density materials, such as lead, albeit surrounded by light or medium density material, in short times. A comparison with algorithms published in literature is also presented.

physics.ins-det↗
arXiv2013

Prospects for measuring the gravitational free-fall of antihydrogen with emulsion detectors

The main goal of the AEgIS experiment at CERN is to test the weak equivalence principle for antimatter. AEgIS will measure the free-fall of an antihydrogen beam traversing a moiré deflectometer. The goal is to determine the gravitational acceleration g for antihydrogen with an initial relative accuracy of 1% by using an emulsion detector combined with a silicon micro-strip detector to measure the time of flight. Nuclear emulsions can measure the annihilation vertex of antihydrogen atoms with a precision of about 1 - 2 microns r.m.s. We present here results for emulsion detectors operated in vacuum using low energy antiprotons from the CERN antiproton decelerator. We compare with Monte Carlo simulations, and discuss the impact on the AEgIS project.

physics.ins-det↗
arXiv2012

Search for the neutron-rich hypernucleus 9ΛHe

Search for the neutron-rich hypernucleus 9LHe is reported by the FINUDA experiment at DAFNE, INFN-LNF, studying (pi+, pi-) pairs in coincidence from the K-stop + 9Be --> 9LHe + pi+ production reaction followed by 9LHe --> 9Li + pi- weak decay. An upper limit of the production rate of 9LHe undergoing this two-body pi- decay is determined to be (2.3 +/- 1.9) 10-6/K-stop at 90% confidence level.

nucl-ex↗
arXiv2012

First observation of the hyper superheavy hydrogen 6ΛH

Three candidate events of the neutron-rich hypernucleus 6ΛH were uniquely identified in the FINUDA experiment at DAΦNE, Frascati, by observing π+ mesons from the (K-stop,π+) production reaction on 6Li targets, in coincidence with π-mesons from 6ΛH \rightarrow 6He+π- weak decay. Details of the experiment and the analysis of its data are reported, leading to an estimate of (2.9\pm2.0)\cdot10-6/K- stop for the 6ΛH production rate times the two-body π- weak decay branching ratio. The 6ΛH binding energy with respect to 5H + Λ was determined jointly from production and decay to be BΛ = (4.0 \pm 1.1) MeV, assuming that 5H is unbound with respect to 3H + 2n by 1.7 MeV. The binding energy determined from production is higher, in each one of the three events, than that determined from decay, with a difference of (0.98 \pm 0.74) MeV here assigned to the 0+g.s. \rightarrow 1+ excitation. The consequences of this assignment to Λ hypernuclear dynamics are briefly discussed.

nucl-ex↗