arXiv subjects

G. Calderini

Publications and source records attributed to G. Calderini.

At least 19 recordsLinked to original sources

arXiv2025

Pixel column issue in the ATLAS Inner Tracker modules

Pixel modules are currently being built for the ATLAS ITk Pixel detector upgrade. During the preproduction phase, recurring chip malfunctioning was observed during electrical testing. It was possible to bypass this issue by disabling some pixel core columns in the ITkPix readout chip. Therefore the issue is called "core column issue" which is a direct disqualifier for a pixel module. A concerning number of cases has been observed in pixel modules with ITkPix v1.1 as well as v2 chips which significantly impacts the module yield. However, the behaviour is erratic and there is not any evidence hinting at the origin of this issue. These proceedings outline the investigations of the issue, highlighting the electrical behaviour during testing, present findings from the data collected via our production database and through visual inspection, and point towards possible causes of the issue.

physics.ins-det↗

arXiv2019

LPNHE scientific perspectives for the European Strategy for Particle Physics

This note summarizes the activities and the scientific and technical perspectives of the Laboratoire de Physique Nucleaire et de Hautes Energies (LPNHE) at Sorbonne University, Paris. Although the ESPP is specifically aimed at particle physics, we discuss in this note in parallel the three scientific lines developed at LPNHE (Particle Physics, Astroparticles, Cosmology), first with the current scientific activities, then for the future activities. However, our conclusions and recommendations are focused on the particle physics strategy.

hep-ph↗

arXiv2018

Performance of Thin Planar \textit{n-on-p} silicon pixels after HL-LHC radiation fluences

The tracking detector of ATLAS, one of the experiments at the Large Hadron Collider (LHC), will be upgraded in 2024-2026 to cope with the challenging environment conditions of the High Luminosity LHC (HL-LHC). The LPNHE, in collaboration with FBK and INFN, has produced 130~$\mu$m thick $n-on-p$ silicon pixel sensors which can withstand the expected large particle fluences at HL- LHC, while delivering data at high rate with excellent hit efficiency. Such sensors were tested on beam before and after irradiation both at CERN-SPS and at DESY, and their performances are presented in this paper. Beam test data indicate that these detectors are suited for all the layers where planar sensors are foreseen in the future ATLAS tracker: hit-efficiency is greater than 97\% for fluences $\Phi \lesssim 7\times10^{15}\rm{n_{eq}/cm^2}$ and module power consumption is within the specified limits. Moreover, at a fluence $\Phi = 1.3\times10^{16}\rm{n_{eq}/cm^2}$, hit-efficiency is still as high as 88\% and charge collection efficiency is about 30\%.

physics.ins-det↗

arXiv2018

Measurement of $\cos{2\beta}$ in $B^{0} \to D^{(*)} h^{0}$ with $D \to K_{S}^{0} \pi^{+} \pi^{-}$ decays by a combined time-dependent Dalitz plot analysis of BaBar and Belle data

We report measurements of $\sin{2\beta}$ and $\cos{2\beta}$ from a time-dependent Dalitz plot analysis of $B^{0} \to D^{(*)} h^{0}$ with $D \to K_{S}^{0} \pi^{+} \pi^{-}$ decays, where the light unflavored and neutral hadron $h^{0}$ is a $\pi^{0}$, $\eta$, or $\omega$ meson. The analysis is performed with a combination of the final data sets of the \babar\ and Belle experiments containing $471 \times 10^{6}$ and $772 \times 10^{6}$ $B\bar{B}$ pairs collected at the $\Upsilon\left(4S\right)$ resonance at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. We measure $\sin{2\beta} = 0.80 \pm 0.14 \,(\rm{stat.}) \pm 0.06 \,(\rm{syst.}) \pm 0.03 \,(\rm{model})$ and $\cos{2\beta} = 0.91 \pm 0.22 \,(\rm{stat.}) \pm 0.09 \,(\rm{syst.}) \pm 0.07 \,(\rm{model})$. The result for the direct measurement of the angle is $\beta = \left( 22.5 \pm 4.4 \,(\rm{stat.}) \pm 1.2 \,(\rm{syst.}) \pm 0.6 \,(\rm{model}) \right)^{\circ}$. The last quoted uncertainties are due to the composition of the $D^{0} \to K_{S}^{0} \pi^{+} \pi^{-}$ decay amplitude model, which is newly established by a Dalitz plot amplitude analysis of a high-statistics $e^{+}e^{-} \to c\bar{c}$ data sample as part of this analysis. We find the first evidence for $\cos2\beta>0$ at the level of $3.7$ standard deviations. The measurement excludes the trigonometric multifold solution $\pi/2 - \beta = (68.1 \pm 0.7)^{\circ}$ at the level of $7.3$ standard deviations and therefore resolves an ambiguity in the determination of the apex of the CKM Unitarity Triangle. The hypothesis of $\beta = 0^{\circ}$ is ruled out at the level of $5.1$ standard deviations, and thus CP violation is observed in $B^{0} \to D^{(*)} h^{0}$ decays.

hep-ex↗

arXiv2018

First evidence for $\cos 2\beta>0$ and resolution of the CKM Unitarity Triangle ambiguity by a time-dependent Dalitz plot analysis of $B^{0} \to D^{(*)} h^{0}$ with $D \to K_{S}^{0} \pi^{+} \pi^{-}$ decays

We present first evidence that the cosine of the CP-violating weak phase $2\beta$ is positive, and hence exclude trigonometric multifold solutions of the CKM Unitarity Triangle using a time-dependent Dalitz plot analysis of $B^{0} \to D^{(*)} h^{0}$ with $D \to K_{S}^{0} \pi^{+} \pi^{-}$ decays, where $h^{0} \in \{\pi^{0}, \eta, \omega \}$ denotes a light unflavored and neutral hadron. The measurement is performed combining the final data sets of the BaBar and Belle experiments collected at the $\Upsilon(4S)$ resonance at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. The data samples contain $( 471 \pm 3 )\times 10^6\, B\bar{B}$ pairs recorded by the BaBar detector and $( 772 \pm 11 )\times 10^6\, B\bar{B}$ pairs recorded by the Belle detector. The results of the measurement are $\sin{2\beta} = 0.80 \pm 0.14 \,(\rm{stat.}) \pm 0.06 \,(\rm{syst.}) \pm 0.03 \,(\rm{model})$ and $\cos{2\beta} = 0.91 \pm 0.22 \,(\rm{stat.}) \pm 0.09 \,(\rm{syst.}) \pm 0.07 \,(\rm{model})$. The result for the direct measurement of the angle $\beta$ of the CKM Unitarity Triangle is $\beta = \left( 22.5 \pm 4.4 \,(\rm{stat.}) \pm 1.2 \,(\rm{syst.}) \pm 0.6 \,(\rm{model}) \right)^{\circ}$. The quoted model uncertainties are due to the composition of the $D^{0} \to K_{S}^{0} \pi^{+} \pi^{-}$ decay amplitude model, which is newly established by performing a Dalitz plot amplitude analysis using a high-statistics $e^{+}e^{-} \to c\bar{c}$ data sample. CP violation is observed in $B^{0} \to D^{(*)} h^{0}$ decays at the level of $5.1$ standard deviations. The significance for $\cos{2\beta}>0$ is $3.7$ standard deviations. The trigonometric multifold solution $\pi/2 - \beta = (68.1 \pm 0.7)^{\circ}$ is excluded at the level of $7.3$ standard deviations. The measurement resolves an ambiguity in the determination of the apex of the CKM Unitarity Triangle.

hep-ex↗

arXiv2018

Beam test measurements of Low Gain Avalanche Detector single pads and arrays for the ATLAS High Granularity Timing Detector

For the high luminosity upgrade of the LHC at CERN, ATLAS is considering the addition of a High Granularity Timing Detector (HGTD) in front of the end cap and forward calorimeters at |z| = 3.5 m and covering the region 2.4 < |{\eta}| < 4 to help reducing the effect of pile-up. The chosen sensors are arrays of 50 {\mu}m thin Low Gain Avalanche Detectors (LGAD). This paper presents results on single LGAD sensors with a surface area of 1.3x1.3 mm2 and arrays with 2x2 pads with a surface area of 2x2 mm^2 or 3x3 mm^2 each and different implant doses of the p+ multiplication layer. They are obtained from data collected during a beam test campaign in Autumn 2016 with a pion beam of 120 GeV energy at the CERN SPS. In addition to several quantities measured inclusively for each pad, the gain, efficiency and time resolution have been estimated as a function of the position of the incident particle inside the pad by using a beam telescope with a position resolution of few {\mu}m. Different methods to measure the time resolution are compared, yielding consistent results. The sensors with a surface area of 1.3x1.3 mm^2 have a time resolution of about 40 ps for a gain of 20 and of about 27 ps for a gain of 50 and fulfill the HGTD requirements. Larger sensors have, as expected, a degraded time resolution. All sensors show very good efficiency and time resolution uniformity.

physics.ins-det↗

arXiv2018

Production and Integration of the ATLAS Insertable B-Layer

During the shutdown of the CERN Large Hadron Collider in 2013-2014, an additional pixel layer was installed between the existing Pixel detector of the ATLAS experiment and a new, smaller radius beam pipe. The motivation for this new pixel layer, the Insertable B-Layer (IBL), was to maintain or improve the robustness and performance of the ATLAS tracking system, given the higher instantaneous and integrated luminosities realised following the shutdown. Because of the extreme radiation and collision rate environment, several new radiation-tolerant sensor and electronic technologies were utilised for this layer. This paper reports on the IBL construction and integration prior to its operation in the ATLAS detector.

physics.ins-det↗

arXiv2015

First Observation of CP Violation in B0->D(*)CP h0 Decays by a Combined Time-Dependent Analysis of BaBar and Belle Data

We report a measurement of the time-dependent CP asymmetry of B0->D(*)CP h0 decays, where the light neutral hadron h0 is a pi0, eta or omega meson, and the neutral D meson is reconstructed in the CP eigenstates K+ K-, K0S pi0 or K0S omega. The measurement is performed combining the final data samples collected at the Y(4S) resonance by the BaBar and Belle experiments at the asymmetric-energy B factories PEP-II at SLAC and KEKB at KEK, respectively. The data samples contain ( 471 +/- 3 ) x 10^6 BB pairs recorded by the BaBar detector and ( 772 +/- 11 ) x 10^6, BB pairs recorded by the Belle detector. We measure the CP asymmetry parameters -eta_f S = +0.66 +/- 0.10 (stat.) +/- 0.06 (syst.) and C = -0.02 +/- 0.07 (stat.) +/- 0.03 (syst.). These results correspond to the first observation of CP violation in B0->D(*)CP h0 decays. The hypothesis of no mixing-induced CP violation is excluded in these decays at the level of 5.4 standard deviations.

hep-ex↗

arXiv2013

Performance of Irradiated Thin Edgeless N-on-P Planar Pixel Sensors for ATLAS Upgrades

In view of the LHC upgrade phases towards the High Luminosity LHC (HL-LHC), the ATLAS experiment plans to upgrade the Inner Detector with an all-silicon system. Because of its radiation hardness and cost effectiveness, the n-on-p silicon technology is a promising candidate for a large area pixel detector. The paper reports on the joint development, by LPNHE and FBK of novel n-on-p edgeless planar pixel sensors, making use of the active trench concept for the reduction of the dead area at the periphery of the device. After discussing the sensor technology, a complete overview of the electrical characterization of several irradiated samples will be discussed. Some comments about detector modules being assembled will be made and eventually some plans will be outlined.

physics.ins-det↗

arXiv2013

Electrical Characterization of a Thin Edgeless N-on-p Planar Pixel Sensors For ATLAS Upgrades

In view of the LHC upgrade phases towards the High Luminosity LHC (HL-LHC), the ATLAS experiment plans to upgrade the Inner Detector with an all-silicon system. Because of its radiation hardness and cost effectiveness, the n-on-p silicon technology is a promising candidate for a large area pixel detector. The paper reports on the joint development, by LPNHE and FBK of novel n-on-p edgeless planar pixel sensors, making use of the active trench concept for the reduction of the dead area at the periphery of the device. After discussing the sensor technology, and presenting some sensors' simulation results, a complete overview of the electrical characterization of the produced devices will be given.

physics.ins-det↗

arXiv2013

Development of Edgeless Silicon Pixel Sensors on p-type substrate for the ATLAS High-Luminosity Upgrade

In view of the LHC upgrade for the High Luminosity Phase (HL-LHC), the ATLAS experiment is planning to replace the Inner Detector with an all-Silicon system. The n-in-p bulk technology represents a valid solution for the modules of most of the layers, given the significant radiation hardness of this option and the reduced cost. The large area necessary to instrument the outer layers will demand to tile the sensors, a solution for which the inefficient region at the border of each sensor needs to be reduced to the minimum size. This paper reports on a joint R&D project by the ATLAS LPNHE Paris group and FBK Trento on a novel n-in-p edgeless planar pixel design, based on the deep-trench process available at FTK.

physics.ins-det↗

arXiv2013

Achievements of the ATLAS Upgrade Planar Pixel Sensors R&D Project

To extend the physics reach of the LHC, accelerator upgrades are planned which will increase the integrated luminosity to beyond 3000 fb^-1 and the pile-up per bunch-crossing by a factor 5 to 10. To cope with the increased occupancy and radiation damage, the ATLAS experiment plans to introduce an all-silicon inner tracker with the HL-LHC upgrade. To investigate the suitability of pixel sensors using the proven planar technology for the upgraded tracker, the ATLAS Upgrade Planar Pixel Sensor R&D Project (PPS) was established comprising 19 institutes and more than 80 scientists. Main areas of research are the performance assessment of planar pixel sensors with different designs and substrate thicknesses up to the HL-LHC fluence, the achievement of slim or active edges to provide low geometric inefficiencies without the need for shingling of modules and the exploration of possibilities for cost reduction to enable the instrumentation of large areas. This paper gives an overview of recent accomplishments and ongoing work of the R&D project.

physics.ins-det↗

arXiv2013

Development of Edgeless n-on-p Planar Pixel Sensors for future ATLAS Upgrades

The development of n-on-p "edgeless" planar pixel sensors being fabricated at FBK (Trento, Italy), aimed at the upgrade of the ATLAS Inner Detector for the High Luminosity phase of the Large Hadron Collider (HL-LHC), is reported. A characterizing feature of the devices is the reduced dead area at the edge, achieved by adopting the "active edge" technology, based on a deep etched trench, suitably doped to make an ohmic contact to the substrate. The project is presented, along with the active edge process, the sensor design for this first n-on-p production and a selection of simulation results, including the expected charge collection efficiency after radiation fluence of $1 \times 10^{15} {\rm n_{eq}}/{\rm cm}^2$ comparable to those expected at HL-LHC (about ten years of running, with an integrated luminosity of 3000 fb$^{-1}$) for the outer pixel layers. We show that, after irradiation and at a bias voltage of 500 V, more than 50% of the signal should be collected in the edge region; this confirms the validity of the active edge approach.

physics.ins-det↗

arXiv2013

Novel Silicon n-on-p Edgeless Planar Pixel Sensors for the ATLAS upgrade

In view of the LHC upgrade phases towards HL-LHC, the ATLAS experiment plans to upgrade the Inner Detector with an all-silicon system. The n-on-p silicon technology is a promising candidate for the pixel upgrade thanks to its radiation hardness and cost effectiveness, that allow for enlarging the area instrumented with pixel detectors. We report on the development of novel n-in-p edgeless planar pixel sensors fabricated at FBK (Trento, Italy), making use of the "active edge" concept for the reduction of the dead area at the periphery of the device. After discussing the sensor technology and fabrication process, we present device simulations (pre- and post-irradiation) performed for different sensor configurations. First preliminary results obtained with the test-structures of the production are shown.

physics.ins-det↗

arXiv2012

Planar Pixel Sensors for the ATLAS Upgrade: Beam Tests results

Results of beam tests with planar silicon pixel sensors aimed towards the ATLAS Insertable B-Layer and High Luminosity LHC (HL-LHC) upgrades are presented. Measurements include spatial resolution, charge collection performance and charge sharing between neighbouring cells as a function of track incidence angle for different bulk materials. Measurements of n-in-n pixel sensors are presented as a function of fluence for different irradiations. Furthermore p-type silicon sensors from several vendors with slightly differing layouts were tested. All tested sensors were connected by bump-bonding to the ATLAS Pixel read-out chip. We show that both n-type and p-type tested planar sensors are able to collect significant charge even after integrated fluences expected at HL-LHC.

physics.ins-det↗

arXiv2012

Search for Physics Beyond the Standard Model at BaBar and Belle

Recent results on the search for new physics at BaBar and Belle B-factories are presented. The search for a light Higgs boson produced in the decay of different Y resonances is shown. In addition, recent measurements aimed to discover invisible final states produced by new physics mechanisms beyond the standard model are presented.

hep-ex↗

arXiv2005

SuperB: a linear high-luminosity B Factory

This paper is based on the outcome of the activity that has taken place during the recent workshop on "SuperB in Italy" held in Frascati on November 11-12, 2005. The workshop was opened by a theoretical introduction of Marco Ciuchini and was structured in two working groups. One focused on the machine and the other on the detector and experimental issues. The present status on CP is mainly based on the results achieved by BaBar and Belle. Estabilishment of the indirect CP violation in B sector in 2001 and of the direct CP violation in 2004 thanks to the success of PEP-II and KEKB e+e- asymmetric B Factories operating at the center of mass energy corresponding to the mass of the Y(4s). With the two B Factories taking data, the Unitarity Triangle is now beginning to be overconstrained by improving the measurements of the sides and now also of the angles alpha, and gamma. We are also in presence of the very intriguing results about the measurements of sin(2 beta) in the time dependent analysis of decay channels via penguin loops, where b --> s sbar s and b --> s dbar d. Tau physics, in particular LFV search, as well as charm and ISR physics are important parts of the scientific program of a SuperB Factory. The physics case together with possible scenarios for the high luminosity SuperB Factory based on the concepts of the Linear Collider and the related experimental issues are discussed.

physics.ins-det↗

arXiv2005

Measurement of the Charge Collection Efficiency after Heavy Non-Uniform Irradiation in BaBar Silicon Detectors

We have investigated the depletion voltage changes, the leakage current increase and the charge collection efficiency of a silicon microstrip detector identical to those used in the inner layers of the BaBar Silicon Vertex Tracker (SVT) after heavy non-uniform irradiation. A full SVT module with the front-end electronics connected has been irradiated with a 0.9 GeV electron beam up to a peak fluence of 3.5 x 10^14 e^-/cm^2, well beyond the level causing substrate type inversion. We irradiated one of the two sensors composing the module with a non-uniform profile with sigma=1.4 mm that simulates the conditions encountered in the BaBar experiment by the modules intersecting the horizontal machine plane. The position dependence of the charge collection properties and the depletion voltage have been investigated in detail using a 1060 nm LED and an innovative measuring technique based only on the digital output of the chip.

physics.ins-det↗