arXiv subjects

G. Carapella

Publications and source records attributed to G. Carapella.

At least 19 recordsLinked to original sources

arXiv2026

Advanced Virgo Plus for O5 -- Design Report Overview

This document presents an overview of the design, implementation, and expected performance of the Advanced Virgo Plus (AdV+) upgrades in view of the O5 observing run. Following the experience gained during the O4 commissioning and operations, the Virgo Collaboration has revised the upgrade strategy to address limitations associated with marginally stable recycling cavities. The O5 upgrade program combines elements from the original AdV+ Phase II project with new design solutions, including the implementation of stable recycling cavities, a major modification to the central interferometer layout, and a comprehensive renewal of critical subsystems. The planned upgrades are organized in two steps, targeting progressive improvements in operational stability, noise reduction, and detector sensitivity. Key developments include new vacuum infrastructures, suspensions, mirrors, optical configurations, quantum noise reduction systems, and high-power laser technologies. The resulting configuration is expected to significantly enhance the interferometer performance, enabling a substantial increase in astrophysical reach and scientific return during O5.

astro-ph.IM↗

arXiv2026

Room Temperature RF Sputtering of Mixed Ionic and Electronic Conductor Nd2Ni0.8Cu0.2O4+d films

Lowering the operating temperature of Solid Oxide Fuel Cells (SOFCs) is essential for improving durability and enabling large scale commercialization. Mixed ionic-electronic conductors (MIECs) of the Ruddlesden-Popper family, such as Nd$2$Ni${1-x}$Cu$x$O${4+δ}$ (NNCO), offer attractive cathode properties due to their high oxygen transport and favourable defect chemistry. In this work, we investigate the fabrication of Nd$2$Ni${0.8}$Cu${0.2}$O${4+δ}$ thin films using a room temperature RF sputtering process followed by moderate temperature annealing. To simplify deposition, a single stoichiometric target was employed, despite the compositional challenges posed by elements with different sputtering yields. We examine the effect of sputtering power density on phase formation and film stoichiometry through X-ray diffraction, Rutherford Backscattering Spectrometry, Energy Dispersive X-ray Spectroscopy, and temperature dependent resistivity measurements. Increasing the sputtering power density strongly reduces the presence of spurious phases and promotes stabilization of the desired n=1 Ruddlesden-Popper phase. Films deposited at 230 W (3.1 W cm$^{-2}$) exhibit a predominant NNCO structure, elemental ratios close to nominal composition, and resistivity values consistent with bulk materials. These findings demonstrate that high power sputtering combined with ex situ annealing enables the production of NNCO thin films suitable for SOFC cathodes. The results support the potential of PVD based approaches for scalable fabrication of advanced SOFC components.

cond-mat.mtrl-sci↗

arXiv2023

Virgo Detector Characterization and Data Quality: results from the O3 run

The Advanced Virgo detector has contributed with its data to the rapid growth of the number of detected gravitational-wave (GW) signals in the past few years, alongside the two Advanced LIGO instruments. First during the last month of the Observation Run 2 (O2) in August 2017 (with, most notably, the compact binary mergers GW170814 and GW170817), and then during the full Observation Run 3 (O3): an 11-months data taking period, between April 2019 and March 2020, that led to the addition of about 80 events to the catalog of transient GW sources maintained by LIGO, Virgo and now KAGRA. These discoveries and the manifold exploitation of the detected waveforms require an accurate characterization of the quality of the data, such as continuous study and monitoring of the detector noise sources. These activities, collectively named {\em detector characterization and data quality} or {\em DetChar}, span the whole workflow of the Virgo data, from the instrument front-end hardware to the final analyses. They are described in details in the following article, with a focus on the results achieved by the Virgo DetChar group during the O3 run. Concurrently, a companion article describes the tools that have been used by the Virgo DetChar group to perform this work.

gr-qc↗

arXiv2023

Virgo Detector Characterization and Data Quality: tools

Detector characterization and data quality studies -- collectively referred to as {\em DetChar} activities in this article -- are paramount to the scientific exploitation of the joint dataset collected by the LIGO-Virgo-KAGRA global network of ground-based gravitational-wave (GW) detectors. They take place during each phase of the operation of the instruments (upgrade, tuning and optimization, data taking), are required at all steps of the dataflow (from data acquisition to the final list of GW events) and operate at various latencies (from near real-time to vet the public alerts to offline analyses). This work requires a wide set of tools which have been developed over the years to fulfill the requirements of the various DetChar studies: data access and bookkeeping; global monitoring of the instruments and of the different steps of the data processing; studies of the global properties of the noise at the detector outputs; identification and follow-up of noise peculiar features (whether they be transient or continuously present in the data); quick processing of the public alerts. The present article reviews all the tools used by the Virgo DetChar group during the third LIGO-Virgo Observation Run (O3, from April 2019 to March 2020), mainly to analyse the Virgo data acquired at EGO. Concurrently, a companion article focuses on the results achieved by the DetChar group during the O3 run using these tools.

gr-qc↗

arXiv2023

The Virgo O3 run and the impact of the environment

Sources of geophysical noise (such as wind, sea waves and earthquakes) or of anthropogenic noise impact ground-based gravitational-wave interferometric detectors, causing transient sensitivity worsening and gaps in data taking. During the one year-long third Observing Run (O3: from April 01, 2019 to March 27, 2020), the Virgo Collaboration collected a statistically significant dataset, used in this article to study the response of the detector to a variety of environmental conditions. We correlated environmental parameters to global detector performance, such as observation range, duty cycle and control losses. Where possible, we identified weaknesses in the detector that will be used to elaborate strategies in order to improve Virgo robustness against external disturbances for the next data taking period, O4, currently planned to start at the end of 2022. The lessons learned could also provide useful insights for the design of the next generation of ground-based interferometers.

gr-qc↗

arXiv2022

Virgo Detector Characterization and Data Quality during the O3 run

The Advanced Virgo detector has contributed with its data to the rapid growth of the number of detected gravitational-wave signals in the past few years, alongside the two LIGO instruments. First, during the last month of the Observation Run 2 (O2) in August 2017 (with, most notably, the compact binary mergers GW170814 and GW170817) and then during the full Observation Run 3 (O3): an 11 months data taking period, between April 2019 and March 2020, that led to the addition of about 80 events to the catalog of transient gravitational-wave sources maintained by LIGO, Virgo and KAGRA. These discoveries and the manifold exploitation of the detected waveforms require an accurate characterization of the quality of the data, such as continuous study and monitoring of the detector noise. These activities, collectively named {\em detector characterization} or {\em DetChar}, span the whole workflow of the Virgo data, from the instrument front-end to the final analysis. They are described in details in the following article, with a focus on the associated tools, the results achieved by the Virgo DetChar group during the O3 run and the main prospects for future data-taking periods with an improved detector.

gr-qc↗

arXiv2022

Progress in the development of a KITWPA for the DARTWARS project

DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS) is a three years project that aims to develop high-performing innovative Traveling Wave Parametric Amplifiers (TWPAs) for low temperature detectors and qubit readout (C-band). The practical development follows two different promising approaches, one based on the Josephson junctions (TWJPA) and the other one based on the kinetic inductance of a high-resistivity superconductor (KITWPA). This paper presents the advancements made by the DARTWARS collaboration to produce a first working prototype of a KITWPA.

quant-ph↗

arXiv2022

Ultra low noise readout with travelling wave parametric amplifiers: the DARTWARS project

The DARTWARS project has the goal of developing high-performing innovative travelling wave parametric amplifiers with high gain, large bandwidth, high saturation power, and nearly quantum-limited noise. The target frequency region for its applications is 5 - 10 GHz, with an expected noise temperature of about 600 mK. The development follows two different approaches, one based on Josephson junctions and one based on kinetic inductance of superconductors. This contribution mainly focuses on the Josephson travelling wave parametric amplifier, presenting its design, preliminary measurements and the test of homogeneity of arrays of Josephson junctions.

quant-ph↗

arXiv2021

Bimodal Approach for Noise Figures of Merit Evaluation in Quantum-Limited Josephson Traveling Wave Parametric Amplifiers

The advent of ultra-low noise microwave amplifiers revolutionized several research fields demanding quantum-limited technologies. Exploiting a theoretical bimodal description of a linear phase-preserving amplifier, in this contribution we analyze some of the intrinsic properties of a model architecture (i.e., an rf-SQUID based Josephson Traveling Wave Parametric Amplifier) in terms of amplification and noise generation for key case study input states (Fock and coherents). Furthermore, we present an analysis of the output signals generated by the parametric amplification mechanism when thermal noise fluctuations feed the device.

cond-mat.supr-con↗

arXiv2021

Calibration of Advanced Virgo and reconstruction of detector strain h(t) during the Observing Run O3

The three Advanced Virgo and LIGO gravitational wave detectors participated to the third observing run (O3) between 1 April 2019 15:00 UTC and 27 March 2020 17:00 UTC,leading to several gravitational wave detections per month. This paper describes the Advanced Virgo detector calibration and the reconstruction of the detector strain $h(t)$ during O3, as well as the estimation of the associated uncertainties. For the first time, the photon calibration technique as been used as reference for Virgo calibration, which allowed to cross-calibrate the strain amplitude of the Virgo and LIGO detectors. The previous reference, so-called free swinging Michelson technique, has still been used but as an independent cross-check. $h(t)$ reconstruction and noise subtraction were processed online, with good enough quality to prevent the need for offline reprocessing, except for the two last weeks of September 2019. The uncertainties for the reconstructed $h(t)$ strain, estimated in this paper in a 20-2000~Hz frequency band, are frequency independent: 5% in amplitude, 35 mrad in phase and 10 $μ$s in timing, with the exception of larger uncertainties around 50 Hz.

gr-qc↗

arXiv2021

Detector Array Readout with Traveling Wave Amplifiers

Noise at the quantum limit over a large bandwidth is a fundamental requirement for future applications operating at millikelvin temperatures, such as the neutrino mass measurement, the next-generation x-ray observatory, the CMB measurement, the dark matter and axion detection, and the rapid high-fidelity readout of superconducting qubits. The read out sensitivity of arrays of microcalorimeter detectors, resonant axion-detectors, and qubits, is currently limited by the noise temperature and bandwidth of the cryogenic amplifiers. The DARTWARS (Detector Array Readout with Traveling Wave AmplifieRS) project has the goal of developing high-performing innovative traveling wave parametric amplifiers (TWPAs) with a high gain, a high saturation power, and a quantum-limited or nearly quantum-limited noise. The practical development follows two different promising approaches, one based on the Josephson junctions and the other one based on the kinetic inductance of a high-resistivity superconductor. In this contribution we present the aims of the project, the adopted design solutions and preliminary results from simulations and measurements.

cond-mat.supr-con↗

arXiv2021

Ternary Quarter Wavelength Coatings for Gravitational Wave Detector Mirrors: Design Optimization via Exhaustive Search

Multimaterial optical coatings are a promising viable option to meet the challenging requirements (in terms of transmittance, absorbance and thermal noise) of next generation gravitational wave detector mirrors. In this paper we focus on ternary coatings consisting of quarter-wavelength thick layers, where a third material (H') is added to the two presently in use, namely Silica (L) and Titania-doped Tantala (H), featuring higher dielectric contrast (against Silica), and lower thermal noise (compared to Titania-doped Tantala), but higher optical losses. We seek the optimal material sequences, featuring minimal thermal (Brownian) noise under prescribed transmittance and absorbance constraints, by exhaustive simulation over all possible configurations, for different values (in a meaningful range) of the optical density and extinction coefficient of the third material. In all cases studied, the optimal designs consist of a stack of (H'|L) doublets topped by a stack of (H|L) doublets, confirming previous heuristic assumptions, and the achievable coating noise power spectral density reduction factor is \sim 0.5. The robustness of the found optimal designs against layer thickness deposition errors and uncertainties and/or fluctuations in the optical losses of the third material is also investigated. Possible margins for further thermal noise reduction by layer thickness optimization, and strategies to implement it, are discussed.

physics.optics↗

arXiv2019

On the performance limits of coatings for gravitational wave detectors made of alternating layers of two materials

The coating design for mirrors used in interferometric detectors of gravitational waves currently consists of stacks of two alternating dielectric materials with different refractive indexes. In order to explore the performance limits of such coatings, we have formulated and solved the design problem as a multiobjective optimization problem consisting of the minimization of both coating transmittance and thermal noise. An algorithm of global optimization (Borg MOEA) has been used without any a priori assumption on the number and thicknesses of the layers in the coating. The algorithm yields to a Pareto tradeoff boundary exhibiting a continuous, decreasing and non convex (bump-like) profile, bounded from below by an exponential curve which can be written in explicit closed form in the transmittance-noise plane. The lower bound curve has the same expression of the relation between transmittance and noise for the quarter wavelength design where the noise coefficient of the high refractive index material assumes a smaller equivalent value. An application of this result allowing to reduce the computational burden of the search procedure is reported and discussed.

astro-ph.IM↗

arXiv2016

Speed limit to the Abrikosov lattice in mesoscopic superconductors

We study the instability of the superconducting state in a mesoscopic geometry for the low pinning material Mo$_3$Ge characterized by a large Ginzburg-Landau parameter. We observe that in the current driven switching to the normal state from a nonlinear region of the Abrikosov flux flow, the mean critical vortex velocity reaches a limiting maximum velocity as a function of the applied magnetic field. Based on time dependent Ginzburg-Landau simulations we argue that the observed behavior is due to the high velocity vortex dynamics confined on a mesoscopic scale. We build up a general phase diagram which includes all possible dynamic configurations of Abrikosov lattice in a mesoscopic superconductor.

cond-mat.supr-con↗

arXiv2013

Nonlinear current-voltage characteristics due to quantum tunneling of phase slips in superconducting Nb nanowire networks

We report on the transport properties of an array of N about 30 interconnected Nb nanowires, grown by sputtering on robust porous Si substrates. The analyzed system exhibits a broad resistive transition in zero magnetic field, H, and highly nonlinear V(I) characteristics as a function of H which can be both consistently described by quantum tunneling of phase slips.

cond-mat.supr-con↗

arXiv2007

Co/Nb/Co low field superconducting spin switch

We report experiments on a superconducting spin switch based on technologically relevant materials as elemental ferromagnetic Co and elemental superconducting Nb. The Co/Nb/Co structure exhibits inverse spin switch effect, can be operated at liquid helium temperature and can switch from superconductive to normal state in rather weak applied magnetic fields. Relevant critical currents as a function of temperature and magnetic field as well as preparation of superconductive or resistive state are addressed here.

cond-mat.supr-con↗

arXiv2002

Experimental investigation of flux motion in exponentially shaped Josephson junctions

We report experimental and numerical analysis of expontentially shaped long Josephson junctions with lateral current injection. Quasi-linear flux flow branches are observed in the current-voltage characteristic of the junctions in the absence of magnetic field. A strongly asymmetric response to an applied magnetic field is also exhibited by the junctions. Experimental data are found in agreement with numerical predictions and demonstrate the existence of a geometry-induced potential experienced by the flux quanta in nonuniform width junctions.

cond-mat.supr-con↗

arXiv2001

Experimental realization of a relativistic fluxon ratchet

We report the observation of the ratchet effect for a relativistic flux quantum trapped in an annular Josephson junction embedded in an inhomogeneous magnetic field. In such a solid state system mechanical quantities are proportional to electrical quantities, so that the ratchet effect represents the realization of a relativistic-flux-quantum-based diode. Mean static voltage response, equivalent to directed fluxon motion, is experimentally demonstrated in such a diode for deterministic current forcing both in the overdamped and in the underdamped dynamical regime. In the underdamped regime, the recently predicted phenomenon of current reversal is also recovered in our fluxon ratchet.

cond-mat.supr-con↗