arXiv subjects

G. Coppi

Publications and source records attributed to G. Coppi.

At least 19 recordsLinked to original sources

arXiv2026

High-accuracy polarimetry for CMB: new frontiers with the POLOCALC project

Modern telescopes observing the Cosmic Microwave Background (CMB) polarization require an exquisite control of systematics to target Inflationary Gravitational Waves (IGW), Cosmic Birefringence (CB), and Primordial Magnetic Fields (PMF). The absolute polarization angle of the detectors is a critical parameter to disentangle the $E$-modes and $B$-modes of the CMB, allowing a correct detection of primordial $B$-modes as well as testing Cosmic Birefringence theories. To this end, we discuss the current status of the POLOCALC project, an ERC Advanced Grant that aims to develop air-borne calibration sources for CMB small-aperture telescopes. The main scientific objective of POLOCALC is to enable a direct calibration of the absolute polarization angle of CMB polarimeters with an accuracy of $0.01 \degree $. We present the latest developments regarding the calibration source, the calibration strategies designed to use drone-based calibrators, and the application to modern ground-based experiments.

astro-ph.CO↗

arXiv2025

The Simons Observatory: forecasted constraints on primordial gravitational waves with the expanded array of Small Aperture Telescopes

We present updated forecasts for the scientific performance of the degree-scale (0.5 deg FWHM at 93 GHz), deep-field survey to be conducted by the Simons Observatory (SO). By 2027, the SO Small Aperture Telescope (SAT) complement will be doubled from three to six telescopes, including a doubling of the detector count in the 93 GHz and 145 GHz channels to 48,160 detectors. Combined with a planned extension of the survey duration to 2035, this expansion will significantly enhance SO's search for a $B$-mode signal in the polarisation of the cosmic microwave background, a potential signature of gravitational waves produced in the very early Universe. Assuming a $1/f$ noise model with knee multipole $\ell_{\rm knee} = 50$ and a moderately complex model for Galactic foregrounds, we forecast a $1\sigma$ (or 68% confidence level) constraint on the tensor-to-scalar ratio $r$ of $\sigma_r = 1.2\times10^{-3}$, assuming no primordial $B$-modes are present. This forecast assumes that 70% of the $B$-mode lensing signal can ultimately be removed using high resolution observations from the SO Large Aperture Telescope (LAT) and overlapping large-scale structure surveys. For more optimistic assumptions regarding foregrounds and noise, and assuming the same level of delensing, this forecast constraint improves to $\sigma_r = 7\times10^{-4}$. These forecasts represent a major improvement in SO's constraining power, being a factor of around 2.5 times better than what could be achieved with the originally planned campaign, which assumed the existing three SATs would conduct a five-year survey.

astro-ph.CO↗

arXiv2025

First release of LiteBIRD simulations from an end-to-end pipeline

The LiteBIRD satellite mission aims at detecting Cosmic Microwave Background $B$ modes with unprecedented precision, targeting a total error on the tensor-to-scalar ratio $r$ of $\delta r \sim 0.001$. Operating from the L2 Lagrangian point of the Sun-Earth system, LiteBIRD will survey the full sky across 15 frequency bands (34 to 448 GHz) for 3 years.The current LiteBIRD baseline configuration employs 4508 detectors sampling at 19.1 Hz to achieve an effective polarization sensitivity of $ 2 \mu\mathrm{K-arcmin}$ and an angular resolution of 31 arcmin (at 140 GHz).We describe the first release of the official LiteBIRD simulations, realized with a new simulation pipeline developed using the LiteBIRD Simulation Framework, see https://github.com/litebird/litebird_sim . This pipeline generates 500 full-sky simulated maps at a Healpix resolution of nside=512. The simulations include also one year of Time Ordered Data for approximately one-third of LiteBIRD's total detectors.

astro-ph.IM↗

arXiv2025

A Simulation Framework for the LiteBIRD Instruments

LiteBIRD, the Lite (Light) satellite for the study of $B$-mode polarization and Inflation from cosmic background Radiation Detection, is a space mission focused on primordial cosmology and fundamental physics. In this paper, we present the LiteBIRD Simulation Framework (LBS), a Python package designed for the implementation of pipelines that model the outputs of the data acquisition process from the three instruments on the LiteBIRD spacecraft: LFT (Low-Frequency Telescope), MFT (Mid-Frequency Telescope), and HFT (High-Frequency Telescope). LBS provides several modules to simulate the scanning strategy of the telescopes, the measurement of realistic polarized radiation coming from the sky (including the Cosmic Microwave Background itself, the Solar and Kinematic dipole, and the diffuse foregrounds emitted by the Galaxy), the generation of instrumental noise and the effect of systematic errors, like pointing wobbling, non-idealities in the Half-Wave Plate, et cetera. Additionally, we present the implementation of a simple but complete pipeline that showcases the main features of LBS. We also discuss how we ensured that LBS lets people develop pipelines whose results are accurate and reproducible. A full end-to-end pipeline has been developed using LBS to characterize the scientific performance of the LiteBIRD experiment. This pipeline and the results of the first simulation run are presented in Puglisi et al. (2025).

astro-ph.IM↗

arXiv2025

On the computational feasibility of Bayesian end-to-end analysis of LiteBIRD simulations within Cosmoglobe

We assess the computational feasibility of end-to-end Bayesian analysis of the JAXA-led LiteBIRD experiment by analysing simulated time ordered data (TOD) for a subset of detectors through the Cosmoglobe and Commander3 framework. The data volume for the simulated TOD is 1.55 TB, or 470 GB after Huffman compression. From this we estimate a total data volume of 238 TB for the full three year mission, or 70 TB after Huffman compression. We further estimate the running time for one Gibbs sample, from TOD to cosmological parameters, to be approximately 3000 CPU hours. The current simulations are based on an ideal instrument model, only including correlated 1/f noise. Future work will consider realistic systematics with full end-to-end error propagation. We conclude that these requirements are well within capabilities of future high-performance computing systems.

astro-ph.IM↗

arXiv2025

LiteBIRD Science Goals and Forecasts: constraining isotropic cosmic birefringence

Cosmic birefringence (CB) is the rotation of the photons' linear polarisation plane during propagation. Such an effect is a tracer of parity-violating extensions of standard electromagnetism and would probe the existence of a new cosmological field acting as dark matter or dark energy. It has become customary to employ cosmic microwave background (CMB) polarised data to probe such a phenomenon. Recent analyses on Planck and WMAP data provide a hint of detection of the isotropic CB angle with an amplitude of around $0.3^\circ$ at the level of $2.4$ to $3.6\sigma$. In this work, we explore the LiteBIRD capabilities in constraining such an effect, accounting for the impact of the more relevant systematic effects, namely foreground emission and instrumental polarisation angles. We build five semi-independent pipelines and test these against four different simulation sets with increasing complexity in terms of non-idealities. All the pipelines are shown to be robust and capable of returning the expected values of the CB angle within statistical fluctuations for all the cases considered. We find that the uncertainties in the CB estimates increase with more complex simulations. However, the trend is less pronounced for pipelines that account for the instrumental polarisation angles. For the most complex case analysed, we find that LiteBIRD will be able to detect a CB angle of $0.3^\circ$ with a statistical significance ranging from $5$ to $13 \, \sigma$, depending on the pipeline employed, where the latter uncertainty corresponds to a total error budget of the order of $0.02^\circ$.

astro-ph.CO↗

arXiv2025

The Simons Observatory: Science Goals and Forecasts for the Enhanced Large Aperture Telescope

We describe updated scientific goals for the wide-field, millimeter-wave survey that will be produced by the Simons Observatory (SO). Significant upgrades to the 6-meter SO Large Aperture Telescope (LAT) are expected to be complete by 2028, and will include a doubled mapping speed with 30,000 new detectors and an automated data reduction pipeline. In addition, a new photovoltaic array will supply most of the observatory's power. The LAT survey will cover about 60% of the sky at a regular observing cadence, with five times the angular resolution and ten times the map depth of Planck. The science goals are to: (1) determine the physical conditions in the early universe and constrain the existence of new light particles; (2) measure the integrated distribution of mass, electron pressure, and electron momentum in the late-time universe, and, in combination with optical surveys, determine the neutrino mass and the effects of dark energy via tomographic measurements of the growth of structure at $z < 3$; (3) measure the distribution of electron density and pressure around galaxy groups and clusters, and calibrate the effects of energy input from galaxy formation on the surrounding environment; (4) produce a sample of more than 30,000 galaxy clusters, and more than 100,000 extragalactic millimeter sources, including regularly sampled AGN light-curves, to study these sources and their emission physics; (5) measure the polarized emission from magnetically aligned dust grains in our Galaxy, to study the properties of dust and the role of magnetic fields in star formation; (6) constrain asteroid regoliths, search for Trans-Neptunian Objects, and either detect or eliminate large portions of the phase space in the search for Planet 9; and (7) provide a powerful new window into the transient universe on time scales of minutes to years, concurrent with observations from Rubin of overlapping sky.

astro-ph.IM↗

arXiv2024

Requirements on the gain calibration for LiteBIRD polarisation data with blind component separation

Future cosmic microwave background (CMB) experiments are primarily targeting a detection of the primordial $B$-mode polarisation. The faintness of this signal requires exquisite control of systematic effects which may bias the measurements. In this work, we derive requirements on the relative calibration accuracy of the overall polarisation gain ($\Delta g_\nu$) for LiteBIRD experiment, through the application of the blind Needlet Internal Linear Combination (NILC) foreground-cleaning method. We find that minimum variance techniques, as NILC, are less affected by gain calibration uncertainties than a parametric approach, which requires a proper modelling of these instrumental effects. The tightest constraints are obtained for frequency channels where the CMB signal is relatively brighter (166 GHz channel, $\Delta {g}_\nu \approx 0.16 \%$), while, with a parametric approach, the strictest requirements were on foreground-dominated channels. We then propagate gain calibration uncertainties, corresponding to the derived requirements, into all frequency channels simultaneously. We find that the overall impact on the estimated $r$ is lower than the required budget for LiteBIRD by almost a factor $5$. The adopted procedure to derive requirements assumes a simple Galactic model. We therefore assess the robustness of obtained results against more realistic scenarios by injecting the gain calibration uncertainties, according to the requirements, into LiteBIRD simulated maps and assuming intermediate- and high-complexity sky models. In this case, we employ the so-called Multi-Clustering NILC (MC-NILC) foreground-cleaning pipeline and obtain that the impact of gain calibration uncertainties on $r$ is lower than the LiteBIRD gain systematics budget for the intermediate-complexity sky model. For the high-complexity case, instead, it would be necessary to tighten the requirements by a factor $1.8$.

astro-ph.CO↗

arXiv2024

Measuring the CMB spectral distortions with COSMO: the multi-mode antenna system

In this work, we present the design and manufacturing of the two multi-mode antenna arrays of the COSMO experiment and the preliminary beam pattern measurements of their fundamental mode compared with simulations. COSMO is a cryogenic Martin-Puplett Fourier Transform Spectrometer that aims at measuring the isotropic y-type spectral distortion of the Cosmic Microwave Background from Antarctica, by performing differential measurements between the sky and an internal, cryogenic reference blackbody. To reduce the atmospheric contribution, a spinning wedge mirror performs fast sky-dips at varying elevations while fast, low-noise Kinetic Inductance detectors scan the interferogram. Two arrays of antennas couple the radiation to the detectors. Each array consists of nine smooth-walled multi-mode feed-horns, operating in the $120-180$ GHz and $210-300$ GHz range, respectively. The multi-mode propagation helps increase the instrumental sensitivity without employing large focal planes with hundreds of detectors. The two arrays have a step-linear and a linear profile, respectively, and are obtained by superimposing aluminum plates made with CNC milling. The simulated multi-mode beam pattern has a $\sim 20^{\circ} - 26^{\circ}$ FWHM for the low-frequency array and $\sim 16^{\circ}$ FWHM for the high-frequency one. The side lobes are below $-15$ dB. To characterize the antenna response, we measured the beam pattern of the fundamental mode using a Vector Network Analyzer, in far-field conditions inside an anechoic chamber at room temperature. We completed the measurements of the low-frequency array and found a good agreement with the simulations. We also identified a few non-idealities that we attribute to the measuring setup and will further investigate. A comprehensive multi-mode measurement will be feasible at cryogenic temperature once the full receiver is integrated.

astro-ph.IM↗

arXiv2024

The Simons Observatory: impact of bandpass, polarization angle and calibration uncertainties on small-scale power spectrum analysis

We study the effects due to mismatches in passbands, polarization angles, and temperature and polarization calibrations in the context of the upcoming cosmic microwave background experiment Simons Observatory (SO). Using the SO multi-frequency likelihood, we estimate the bias and the degradation of constraining power in cosmological and astrophysical foreground parameters assuming different levels of knowledge of the instrumental effects. We find that incorrect but reasonable assumptions about the values of all the systematics examined here can have significant effects on cosmological analyses, hence requiring marginalization approaches at the likelihood level. When doing so, we find that the most relevant effect is due to bandpass shifts. When marginalizing over them, the posteriors of parameters describing astrophysical microwave foregrounds (such as radio point sources or dust) get degraded, while cosmological parameters constraints are not significantly affected. Marginalization over polarization angles with up to 0.25$^\circ$ uncertainty causes an irrelevant bias $\lesssim 0.05 \sigma$ in all parameters. Marginalization over calibration factors in polarization broadens the constraints on the effective number of relativistic degrees of freedom $N_\mathrm{eff}$ by a factor 1.2, interpreted here as a proxy parameter for non standard model physics targeted by high-resolution CMB measurements.

astro-ph.CO↗

arXiv2023

Polarization fraction of Planck Galactic cold clumps and forecasts for the Simons Observatory

We measure the polarization fraction of a sample of $6282$ Galactic cold clumps at $353 \, \mathrm{GHz} $, consisting of $Planck$ Galactic cold clump (PGCC) catalogue category 1 objects (flux densities measured with signal-to-noise ratio $(\mathrm{S/N}) > 4$). We find the mean-squared polarization fraction at $353 \, \mathrm{GHz} $ to be $ \langle \Pi ^ 2 \rangle = [ 4.79 \pm 0.44 ] \times 10 ^ {-4} $ equating to an $ 11 \, \sigma $ detection of polarization. We test if the polarization fraction depends on the clumps' physical properties, including flux density, luminosity, Galactic latitude and physical distance. We see a trend towards increasing polarization fraction with increasing Galactic latitude, but find no evidence that polarization depends on the other tested properties. The Simons Observatory, with an angular resolution of order $1 \, \mathrm{arcmin } $ and noise levels between $22$ and $54$ $ \mu \mathrm{ K-arcmin } $ at high frequencies, will substantially enhance our ability to determine the magnetic field structure in Galactic cold clumps. At $\ge5\,\sigma$ significance, we predict the Simons Observatory will detect at least $\sim12,000$ cold clumps in intensity and $\sim430$ cold clumps in polarization. This number of polarization detections would represent a two orders of magnitude increase over the current $Planck$ results. We also release software that can be used to mask these Galactic cold clumps in other analyses.

astro-ph.GA↗

arXiv2022

The POLARBEAR-2 and Simons Array Focal Plane Fabrication Status

We present on the status of POLARBEAR-2 A (PB2-A) focal plane fabrication. The PB2-A is the first of three telescopes in the Simon Array (SA), which is an array of three cosmic microwave background (CMB) polarization sensitive telescopes located at the POLARBEAR (PB) site in Northern Chile. As the successor to the PB experiment, each telescope and receiver combination is named as PB2-A, PB2-B, and PB2-C. PB2-A and -B will have nearly identical receivers operating at 90 and 150 GHz while PB2-C will house a receiver operating at 220 and 270 GHz. Each receiver contains a focal plane consisting of seven close-hex packed lenslet coupled sinuous antenna transition edge sensor bolometer arrays. Each array contains 271 di-chroic optical pixels each of which have four TES bolometers for a total of 7588 detectors per receiver. We have produced a set of two types of candidate arrays for PB2-A. The first we call Version 11 (V11) and uses a silicon oxide (SiOx) for the transmission lines and cross-over process for orthogonal polarizations. The second we call Version 13 (V13) and uses silicon nitride (SiNx) for the transmission lines and cross-under process for orthogonal polarizations. We have produced enough of each type of array to fully populate the focal plane of the PB2-A receiver. The average wirebond yield for V11 and V13 arrays is 93.2% and 95.6% respectively. The V11 arrays had a superconducting transition temperature (Tc) of 452 +/- 15 mK, a normal resistance (Rn) of 1.25 +/- 0.20 Ohms, and saturations powers of 5.2 +/- 1.0 pW and 13 +/- 1.2 pW for the 90 and 150 GHz bands respectively. The V13 arrays had a superconducting transition temperature (Tc) of 456 +/-6 mK, a normal resistance (Rn) of 1.1 +/- 0.2 Ohms, and saturations powers of 10.8 +/- 1.8 pW and 22.9 +/- 2.6 pW for the 90 and 150 GHz bands respectively.

astro-ph.IM↗

arXiv2021

The COSmic Monopole Observer (COSMO)

The COSmic Monopole Observer (COSMO) is an experiment to measure low-level spectral distortions in the isotropic component of the Cosmic Microwave Background (CMB). Deviations from a pure blackbody spectrum are expected at low level ($<$ 1 ppm) due to several astrophysical and cosmological phenomena, and promise to provide important independent information on the early and late phases of the universe. They have not been detected yet, due to the extreme accuracy required, the best upper limits being still those from the COBE-FIRAS mission. COSMO is based on a cryogenic differential Fourier Transform Spectrometer, measuring the spectral brightness difference between the sky and an accurate cryogenic blackbody. The first implementation of COSMO, funded by the Italian PRIN and PNRA programs, will operate from the Concordia station at Dome-C, in Antarctica, and will take advantage of a fast sky-dip technique to get rid of atmospheric emission and its fluctuations, separating them from the monopole component of the sky brightness. Here we describe the instrument design, its capabilities, the current status. We also discuss its subsequent implementation in a balloon-flight, which has been studied within the COSMOS program of the Italian Space Agency.

astro-ph.IM↗

arXiv2021

The large scale polarization explorer (LSPE) for CMB measurements: performance forecast

[Abridged] The measurement of the polarization of the Cosmic Microwave Background radiation is one of the current frontiers in cosmology. In particular, the detection of the primordial B-modes, could reveal the presence of gravitational waves in the early Universe. The detection of such component is at the moment the most promising technique to probe the inflationary theory describing the very early evolution of the Universe. We present the updated performance forecast of the Large Scale Polarization Explorer (LSPE), a program dedicated to the measurement of the CMB polarization. LSPE is composed of two instruments: Strip, a radiometer-based telescope on the ground in Tenerife, and SWIPE (Short-Wavelength Instrument for the Polarization Explorer) a bolometer-based instrument designed to fly on a winter arctic stratospheric long-duration balloon. The program is among the few dedicated to observation of the Northern Hemisphere, while most of the international effort is focused into ground-based observation in the Southern Hemisphere. Measurements are currently scheduled in Winter 2021/22 for SWIPE, with a flight duration up to 15 days, and in Summer 2021 with two years observations for Strip. We describe the main features of the two instruments, identifying the most critical aspects of the design, in terms of impact into performance forecast. We estimate the expected sensitivity of each instrument and propagate their combined observing power to the sensitivity to cosmological parameters, including the effect of scanning strategy, component separation, residual foregrounds and partial sky coverage. We also set requirements on the control of the most critical systematic effects and describe techniques to mitigate their impact. LSPE can reach a sensitivity in tensor-to-scalar ratio of $σ_r<0.01$, and improve constrains on other cosmological parameters.

astro-ph.IM↗

arXiv2020

Progress report on the Large Scale Polarization Explorer

The Large Scale Polarization Explorer (LSPE) is a cosmology program for the measurement of large scale curl-like features (B-modes) in the polarization of the Cosmic Microwave Background. Its goal is to constrain the background of inflationary gravity waves traveling through the universe at the time of matter-radiation decoupling. The two instruments of LSPE are meant to synergically operate by covering a large portion of the northern microwave sky. LSPE/STRIP is a coherent array of receivers planned to be operated from the Teide Observatory in Tenerife, for the control and characterization of the low-frequency polarized signals of galactic origin; LSPE/SWIPE is a balloon-borne bolometric polarimeter based on 330 large throughput multi-moded detectors, designed to measure the CMB polarization at 150 GHz and to monitor the polarized emission by galactic dust above 200 GHz. The combined performance and the expected level of systematics mitigation will allow LSPE to constrain primordial B-modes down to a tensor/scalar ratio of $10^{-2}$. We here report the status of the STRIP pre-commissioning phase and the progress in the characterization of the key subsystems of the SWIPE payload (namely the cryogenic polarization modulation unit and the multi-moded TES pixels) prior to receiver integration.

astro-ph.IM↗

arXiv2020

QUBIC: the Q & U Bolometric Interferometer for Cosmology

The Q & U Bolometric Interferometer for Cosmology, QUBIC, is an innovative experiment designed to measure the polarization of the Cosmic Microwave Background and in particular the signature left therein by the inflationary expansion of the Universe. The expected signal is extremely faint, thus extreme sensitivity and systematic control are necessary in order to attempt this measurement. QUBIC addresses these requirements using an innovative approach combining the sensitivity of Transition Edge Sensor cryogenic bolometers, with the deep control of systematics characteristic of interferometers. This makes QUBIC unique with respect to others classical imagers experiments devoted to the CMB polarization. In this contribution we report a description of the QUBIC instrument including recent achievements and the demonstration of the bolometric interferometry performed in lab. QUBIC will be deployed at the observation site in Alto Chorrillos, in Argentina at the end of 2019.

astro-ph.IM↗

arXiv2019

Cold optical design for the Large Aperture Simons Observatory telescope

The Simons Observatory will consist of a single large (6 m diameter) telescope and a number of smaller (0.5 m diameter) refracting telescopes designed to measure the polarization of the Cosmic Microwave Background to unprecedented accuracy. The large aperture telescope is the same design as the CCAT-prime telescope, a modified Crossed Dragone design with a field-of-view of over 7.8 degrees diameter at 90 GHz. This paper presents an overview of the cold reimaging optics for this telescope and what drove our choice of 350-400 mm diameter silicon lenses in a 2.4 m cryostat over other possibilities. We will also consider the future expandability of this design to CMB Stage-4 and beyond.

astro-ph.IM↗

arXiv2019

QUBIC: using NbSi TESs with a bolometric interferometer to characterize the polarisation of the CMB

QUBIC (Q \& U Bolometric Interferometer for Cosmology) is an international ground-based experiment dedicated in the measurement of the polarized fluctuations of the Cosmic Microwave Background (CMB). It is based on bolometric interferometry, an original detection technique which combine the immunity to systematic effects of an interferometer with the sensitivity of low temperature incoherent detectors. QUBIC will be deployed in Argentina, at the Alto Chorrillos mountain site near San Antonio de los Cobres, in the Salta province. The QUBIC detection chain consists in 2048 NbSi Transition Edge Sensors (TESs) cooled to 350mK.The voltage-biased TESs are read out with Time Domain Multiplexing based on Superconducting QUantum Interference Devices (SQUIDs) at 1 K and a novel SiGe Application-Specific Integrated Circuit (ASIC) at 60 K allowing to reach an unprecedented multiplexing (MUX) factor equal to 128. The QUBIC experiment is currently being characterized in the lab with a reduced number of detectors before upgrading to the full instrument. I will present the last results of this characterization phase with a focus on the detectors and readout system.

astro-ph.IM↗