arXiv subjects

G. Saviano

Publications and source records attributed to G. Saviano.

At least 19 recordsLinked to original sources

arXiv2026

Dark Matter Sensitivity of the CYGNO Detector with HFO-1234ze Enhanced Gas Mixtures

The CYGNO collaboration introduces an innovative approach to direct dark matter detection, proposing a high-resolution optical Time Projection Chamber. It operates at atmospheric pressure with a He:CF$_{4}$ (60:40) gas mixture and uses a triple Gas Electron Multiplier stage for signal amplification. A key feature is its optical readout system, which captures the scintillation light produced during the electron avalanche. This setup allows 3D event reconstruction by combining the time profile of the light detected by photomultiplier tubes with high-granularity, pixelated X-Y tracking recorded by a scientific camera. The CYGNO experiment's projected sensitivity to both spin-independent and spin-dependent interactions is competitive in the framework of directional dark matter detectors. However, incorporating a hydrogen-based gas would introduce an even lighter target, further improving the detection potential at low dark matter masses. In this work, we present the performance characterization of one of the CYGNO experiment prototypes, MANGO, operated with the standard gas mixture enriched with varying concentrations of HFO-1234ze, a gas with a promising low global warming potential. The study includes measurements of the detector charge gain and scintillation yield for each configuration. In addition, to evaluate the impact of HFO-1234ze on scintillation light quenching, the secondary scintillation spectrum was collected for each gas mixture tested.

physics.ins-det↗

arXiv2026

He-CF4-CH4 ternary mixtures as target gas for the CYGNO directional dark matter experiment

The CYGNO collaboration is advancing a high-resolution optical Time Projection Chamber (TPC) for directional dark matter searches and solar neutrino spectroscopy at LNGS. The detector uses a He-40%CF4 gas mixture at atmospheric pressure and a triple-GEM cascade for ionization signal amplification. Scintillation light from GEM electron avalanches is read out using sCMOS cameras, enabling high sensitivity to interactions in the few keV range, alongside precise ionization event tracking and particle identification. This study investigates the effects of adding 3-10% methane to the He-40%CF4 mixture. Methane improves the electrical stability of the TPC, allowing for higher GEM voltages before discharge onset, which compensates for its scintillation quenching and leads to enhanced overall scintillation yield. Compared to prior studies performed with isobutane, methane demonstrates a lower quenching effect on visible and UV photons while maintaining good energy resolution. Importantly, the inclusion of methane lowers the dark matter detection threshold by providing a lighter target and extending track lengths of light nuclear recoils, thus enhancing directional discrimination. These results establish methane as a promising additive for optimizing CYGNO's performance in detecting low-mass dark matter candidates.

physics.ins-det↗

arXiv2026

Simulation of the CYGNO Gaseous TPC Optical Readout

Gaseous Time Projection Chambers with Optical Readout are sensitive detectors suitable for 3D measurement of low-energy O(1 keV) particles and are proposed for detecting rare events such as Dark Matter particle interactions. The CYGNO collaboration is developing such a detector with a high spatial and energy resolution, leveraging an innovative optical readout system. A reliable simulation of the detector response is needed to properly assess the physics reach of this technique and to better understand the performance of the detector in the development phase. Such a simulation cannot entirely rely on existing software packages; indeed, none of the available tools is capable of properly and reliably treating the different phenomena occurring in the detector, from the primary interaction in the gas volume throughout the whole detector response model, including charge transport, light production and propagation, and the response of the optical sensors. In this paper, we present a modeling of the detector response tuned on the CYGNO Optical TPC case; a description of the method is reported together with comparisons with experimental data from the LIME prototype to demonstrate the simulation performances.

physics.ins-det↗

arXiv2026

Upgrade of the Trigger and Data Acquisition System for Continuous Imaging and Multi-Camera Operation in CYGNO

The CYGNO experiment employs an optical readout to image particle interactions in a gaseous Time Projection Chamber (TPC), combining cameras and photomultiplier tubes (PMTs) to achieve high spatial resolution and timing information. This approach enables detailed track reconstruction but poses significant challenges for data acquisition, particularly in view of the next experimental phase, CYGNO-04, which will operate multiple cameras simultaneously. In this paper, we present an upgrade of the CYGNO Trigger and Data Acquisition (T-DAQ) system, developed starting from the LIME configuration and validated on the MANGO prototype. The upgrade introduces a continuous imaging acquisition mode, substantially reducing the camera dead time, together with an extended trigger time-tagging scheme that provides a robust global time reference for PMT signals. A synchronous multi-camera DAQ architecture is also implemented and tested, enabling coordinated operation of multiple optical sensors without a master camera. The performance of the upgraded system is validated through dedicated tests, demonstrating stable continuous acquisition, reliable time-tagging, and consistent synchronization across multiple cameras. These results establish a solid and scalable foundation for the CYGNO-04 DAQ and represent a key step toward efficient data acquisition in future large-scale optical TPC detectors.

physics.ins-det↗

arXiv2026

Characterization of field cage and cathode for low radioactivity operation with the CYGNO experiment

Dark matter, which is considered to account for approximately the 27% of the Universe's energy-mass content, remains an open issue in modern particle physics along with its composition. The CYGNO Experiment aims to exploit an innovative approach applied to the direct detection search of low energy nuclear recoils possibly induced by cold particle-like dark matter candidates. CYGNO employs a directional detector based on a Time Projection Chamber (TPC) filled with a He:CF$_{4}$ gas mixture and equipped with an optical readout. Currently, the CYGNO Collaboration is constructing the detector demonstrator, CYGNO-04, in Hall F at Laboratori Nazionali del Gran Sasso (LNGS). This 0.4 m$^3$ detector has the goal of proving the scalability of the technology and assessing the physics and radiopurity capabilities. Given the low radioactivity requirements, especially in internal components such as field cage and cathode, the reduction of material while keeping the correct electrical behavior is paramount. In this paper, we present the validation of several internal components, mainly focusing on the field cage material and support structure. The tests included geometrical asymmetries in the electric field response, collection efficiency as well as measurement of known physical quantities. A preferred configuration is found with a structure based on Nylon material which supports a PET or Kapton sheet with copper strips deposited on.

physics.ins-det↗

arXiv2026

Fast reconstruction-based ROI triggering via anomaly detection in the CYGNO optical TPC

Optical-readout Time Projection Chambers (TPCs) produce megapixel-scale images whose fine-grained topological information is essential for rare-event searches, but whose size challenges real-time data selection. We present an unsupervised, reconstruction-based anomaly-detection strategy for fast Region-of-Interest (ROI) extraction that operates directly on minimally processed camera frames. A convolutional autoencoder trained exclusively on pedestal images learns the detector noise morphology without labels, simulation, or fine-grained calibration. Applied to standard data-taking frames, localized reconstruction residuals identify particle-induced structures, from which compact ROIs are extracted via thresholding and spatial clustering. Using real data from the CYGNO optical TPC prototype, we compare two pedestal-trained autoencoder configurations that differ only in their training objective, enabling a controlled study of its impact. The best configuration retains (93.0 +/- 0.2)% of reconstructed signal intensity while discarding (97.8 +/- 0.1)% of the image area, with an inference time of approximately 25 ms per frame on a consumer GPU. The results demonstrate that careful design of the training objective is critical for effective reconstruction-based anomaly detection and that pedestal-trained autoencoders provide a transparent and detector-agnostic baseline for online data reduction in optical TPCs.

physics.ins-det↗

arXiv2026

The CYGNO experiment: a gaseous TPC with optical readout for rare events searches

The CYGNO collaboration is developing a novel strategy for directional Dark Matter searches based on a gaseous Time Projection Chamber (TPC). The detector is optimized for the exploration of light (0.5-50 GeV) WIMPs-like particles and employs a He/CF4 gas mixture at atmospheric pressure, sensitive to both spin-dependent and spin-independent interactions. A key feature of the project is its optical readout, which relies on photon detection rather than charge collection. In CYGNO detectors, electrons released by ionizing tracks drift toward an amplification stage of three Gas Electron Multipliers (GEMs). The electron avalanches generate scintillation light that is captured by scientific CMOS (sCMOS) cameras for high-resolution two-dimensional imaging and by Photomultiplier Tubes (PMTs) that provide a precise time profile along the drift direction. This allows a 3D event reconstruction, detailed energy deposition mapping, and effective topology and head-to-tail discrimination. Building on the achievements of the 50 L prototype (LIME), which successfully operated underground at LNGS, the next step is the deployment of a 0.4 m3 demonstrator, CYGNO-04, to be completed in 2026. The demonstrator will validate scalability and confirm the advantages of the proposed technique. Recent results from LIME highlight strong progress in 3D tracking and particle identification. The current status of CYGNO-04 and its role in advancing the program will be presented as well.

physics.ins-det↗

arXiv2026

Trigger Optimization and Event Classification for Dark Matter Searches in the CYGNO Experiment Using Machine Learning

The CYGNO experiment employs an optical-readout Time Projection Chamber (TPC) to search for rare low-energy interactions using finely resolved scintillation images. While the optical readout provides rich topological information, it produces large, sparse megapixel images that challenge real-time triggering, data reduction, and background discrimination. We summarize two complementary machine-learning approaches developed within CYGNO. First, we present a fast and fully unsupervised strategy for online data reduction based on reconstruction-based anomaly detection. A convolutional autoencoder trained exclusively on pedestal images (i.e. frames acquired with GEM amplification disabled) learns the detector noise morphology and highlights particle-induced structures through localized reconstruction residuals, from which compact Regions of Interest (ROIs) are extracted. On real prototype data, the selected configuration retains (93.0 +/- 0.2)% of reconstructed signal intensity while discarding (97.8 +/- 0.1)% of the image area, with ~25 ms per-frame inference time on a consumer GPU. Second, we report a weakly supervised application of the Classification Without Labels (CWoLa) framework to data acquired with an Americium--Beryllium neutron source. Using only mixed AmBe and standard datasets (no event-level labels), a convolutional classifier learns to identify nuclear-recoil-like topologies. The achieved performance approaches the theoretical limit imposed by the mixture composition and isolates a high-score population with compact, approximately circular morphologies consistent with nuclear recoils.

physics.ins-det↗

arXiv2026

First Optical Observation of Negative Ion Drift at Surface Pressure

We report the first observation of Negative Ion Drift (NID) at surface pressure of $900 \pm 7$ mbar at Laboratori Nazionali del Gran Sasso in a He:CF$_4$:SF$_6$ mixture using an optically read out Time Projection Chamber (TPC) within the CYGNO/INITIUM project. We present the first PMT waveform analysis in the NID regime, interpreting the temporal light pattern through a model that combines track geometry and charge transport. The inferred drift velocities correspond to mobilities of O(cm$^2$ V$^{-1}$ s$^{-1}$), consistent with negative ion transport. The observed linear scaling of the time extension mean with drift distance reveals the presence of a faster minority charge carrier population in addition to the dominant SF$_6^-$ species, drifting at a $\sim$25\% higher velocity under external inputs. These results demonstrate multi-species negative ion drift operation at surface pressure in a He:CF$_4$:SF$_6$ mixture and open a concrete path toward large scale, low diffusion optical TPCs for rare event searches.

physics.ins-det↗

arXiv2025

Characterization of cutting-edge CMOS Active Pixel sensors within the CYGNO Experiment

Time Projection Chambers equipped with Gas Electron Multipliers and optical readout by scientific CMOS cameras are a promising technology for low-energy particle detection, as demonstrated by the CYGNO experiment. To help identify the optimal CYGNO detector configuration, we performed a detailed characterization of two state-of-the-art scientific CMOS sensors, focusing on dark-signal behavior across different exposure times and on detection sensitivity, assessed using the well-defined X-ray emissions from a 55Fe source, which reproduce the low-light conditions expected in CYGNO. CYGNO currently employs a very low-noise Hamamatsu sensor, the ORCA-Fusion, for testing and validation of its detection system. Hamamatsu has recently introduced two new sensors that may be of interest for future upgrades. The first is an improved version of the current model, the ORCA-Fusion-BT, featuring a back-illuminated design that reaches a quantum efficiency of up to 95% at 550 nm. The second is a next-generation sensor, the ORCA-Quest. Although its peak quantum efficiency is not as high as that of the Fusion-BT, it offers high sensitivity over a broader spectral range, extending into the ultraviolet region, and provides ultra-low readout noise of 0.27 electrons, about 2.6 times lower than that of the Fusion family. These two sensors therefore represent a significant opportunity to enhance the performance of scientific experiments, including those conducted by the CYGNO collaboration. This document presents a comprehensive characterization of these sensors to evaluate their relevance for experiments operating in photon-limited environments and their suitability for integration into the CYGNO detector system.

physics.ins-det↗

arXiv2025

A standalone simulation program for Resistive Cylindrical Chamber (RCC)

In recent years, the Resistive Cylindrical Chamber (RCC) has been introduced as a novel gaseous detector, extending the well-established Resistive Plate Chambers (RPCs) to the case of cylindrical electrode geometry. Preliminary experimental studies have highlighted several promis- ing features of this configuration, motivating the need for further systematic investigations of its operation. In contrast, from the simulation perspective, detailed studies of the RCC have not been performed yet, despite the fact that the cylindrical geometry introduces new degrees of freedom- such as cylinder electrodes radii and voltage polarity- which lead to asymmetric behaviour of the avalanche development according to the polarity of the applied voltage between the electrodes. In this work we present a standalone simulation program specifically designed to model avalanche growth and signal induction in both RPC and RCC geometries. The code implements a stepwise transport model for electron multiplication, includes approximate space-charge effects, and evalu- ates the induced signals on an external electrode. The simulation has been validated against experimental data for planar RPCs and subsequently applied to RCC geometries. The results demonstrate that key observables such as induced charge and efficiency for the planar geometry are well reproduced and highlights the role of electric-field asymmetry in the cylindrical configuration. These findings provide quantitative insights into the impact of detector geometry on avalanche dynamics.

hep-ex↗

arXiv2025

Signal shape studies and rate dependence of HFO-based gas mixtures in RPC detectors

The RPCs employed at the LHC experiments are currently operated in avalanche mode, with a mixture containing a large fraction of C$_{2}$H$_{2}$F$_{4}$ ($\approx$90\% or more) with the addition of i-C$_{4}$H$_{10}$ and SF$_{6}$ in different concentrations. However, C$_{2}$H$_{2}$F$_{4}$ and SF$_{6}$ are fluorinated greenhouse gases (F-gases) with Global Warming Potential (GWP) of $\approx$1400 and $\approx$22800, respectively. EU regulations imposed a progressive phase-down of C$_{2}$H$_{2}$F$_{4}$ production and consumption, aiming at strongly reducing its emission. This is already resulting in an increase of its price and reduction in availability. The most desirable long-term solution to this problem is to find an alternative, F-gases-free gas mixture, able to maintain similar detector performance. To address this challenge, the RPC ECOGasas@GIF++ collaboration (including RPC experts of ALICE, ATLAS, CMS, SHiP/LHCb, and the CERN EP-DT group) was created in 2019. The collaboration is currently studying a gas from the olefine family, the C$_{3}$H$_{2}$F$_{4}$ (or simply HFO, with GWP $\approx$6), to be used, in combination with CO$_{2}$, as a substitute for C$_{2}$H$_{2}$F$_{4}$. This contribution will focus on the signal shape studies that have been carried out by the collaboration during dedicated beam test periods. The methodology used in the data analysis will be presented, together with the results obtained with several HFO-based gas mixtures, and with the currently employed one. Furthermore, results on the counting-rate dependence of the RPC performance, obtained by combining the muon beam with the GIF++ $^{137}$Cs source with different attenuation factors, will also be presented.

physics.ins-det↗

arXiv2024

Preliminary results on the long term operation of RPCs with eco-friendly gas mixtures under irradiation at the CERN Gamma Irradiation Facility

Since 2019 a collaboration between researchers from various institutes and experiments (i.e. ATLAS, CMS, ALICE, LHCb/SHiP and the CERN EP-DT group), has been operating several RPCs with diverse electronics, gas gap thicknesses and detector layouts at the CERN Gamma Irradiation Facility (GIF++). The studies aim at assessing the performance of RPCs when filled with new eco-friendly gas mixtures in avalanche mode and in view of evaluating possible ageing effects after long high background irradiation periods, e.g. High-Luminosity LHC phase. This challenging research is also part of a task of the European AidaInnova project. A promising eco-friendly gas identified for RPC operation is the tetrafluoruropropene (C$_{3}$H$_{2}$F$_{4}$, commercially known as HFO-1234ze) that has been studied at the CERN GIF++ in combination with different percentages of CO$_2$. Between the end of 2021 and 2022 several beam tests have been carried out to establish the performance of RPCs operated with such mixtures before starting the irradiation campaign for the ageing study. Results of these tests for different RPCs layouts and different gas mixtures, under increasing background rates are presented here, together with the preliminary outcome of the detector ageing tests.

physics.ins-det↗

arXiv2024

Enhancing the light yield of He:CF$_4$ based gaseous detector

The CYGNO experiment aims to build a large ($\mathcal{O}(10)$ m$^3$) directional detector for rare event searches, such as nuclear recoils (NRs) induced by dark matter (DM), such as weakly interactive massive particles (WIMPs). The detector concept comprises a time projection chamber (TPC), filled with a He:CF$_4$ 60/40 scintillating gas mixture at room temperature and atmospheric pressure, equipped with an amplification stage made of a stack of three gas electron multipliers (GEMs) which are coupled to an optical readout. The latter consists in scientific CMOS (sCMOS) cameras and photomultipliers tubes (PMTs). The maximisation of the light yield of the amplification stage plays a major role in the determination of the energy threshold of the experiment. In this paper, we simulate the effect of the addition of a strong electric field below the last GEM plane on the GEM field structure and we experimentally test it by means of a 10$\times$10 cm$^2$ readout area prototype. The experimental measurements analyse stacks of different GEMs and helium concentrations in the gas mixture combined with this extra electric field, studying their performances in terms of light yield, energy resolution and intrinsic diffusion. It is found that the use of this additional electric field permits large light yield increases without degrading intrinsic characteristics of the amplification stage with respect to the regular use of GEMs.

physics.ins-det↗

arXiv2024

Charge Amplification in Low Pressure CF4:SF6:He Mixtures with a Multi-Mesh ThGEM for Directional Dark Matter Searches

The CYGNO collaboration is developing next generation directional Dark Matter (DM) detection experiments, using gaseous Time Projection Chambers (TPCs), as a robust method for identifying Weakly Interacting Massive Particles (WIMPs) below the Neutrino Fog. SF6 is potentially ideal for this since it provides a high fluorine content, enhancing sensitivity to spin-dependent interactions and, as a Negative Ion Drift (NID) gas, reduces charge diffusion leading to improved positional resolution. CF4, although not a NID gas, has also been identified as a favourable gas target as it provides a scintillation signal which can be used for a complimentary light/charge readout approach. These gases can operate at low pressures to elongate Nuclear Recoil (NR) tracks and facilitate directional measurements. In principle, He could be added to low pressure SF6/CF4 without significant detriment to the length of 16S, 12C, and 19F recoils. This would improve the target mass, sensitivity to lower WIMP masses, and offer the possibility of atmospheric operation; potentially reducing the cost of a containment vessel. In this article, we present gas gain and energy resolution measurements, taken with a Multi-Mesh Thick Gaseous Electron Multiplier (MMThGEM), in low pressure SF6 and CF4:SF6 mixtures following the addition of He. We find that the CF4:SF6:He mixtures tested were able to produce gas gains on the order of 10^4 up to a total pressure of 100 Torr. These results demonstrate an order of magnitude improvement in charge amplification in NID gas mixtures with a He component.

physics.ins-det↗

arXiv2024

Status of the production of GEM chambers for the CMS experiment at Large Hadron Collider

The High Luminosity LHC phase includes an upgrade to the muon stations for the CMS Experiment. CMS trigger and muon identification performance will be crucial, and it is, therefore, necessary to install new GEM stations to extend acceptance in the high-η region. An explanation of the quality control test and an update on the status of production will be provided.

physics.ins-det↗

arXiv2024

In-beam performance of a Resistive Plate Chamber operated with eco-friendly gas mixtures

ALICE (A Large Ion Collider Experiment) studies the Quark-Gluon Plasma (QGP): a deconfined state of matter obtained in ultra-relativistic heavy-ion collisions. One of the probes for QGP study are quarkonia and open heavy flavour, of which ALICE exploits the muonic decay. A set of Resistive Plate Chambers (RPCs), placed in the forward rapidity region of the ALICE detector, is used for muon identification purposes. The correct operation of these detectors is ensured by the choice of the proper gas mixture. Currently they are operated with a mixture of C$_{2}$H$_{2}$F$_{4}$, i-C$_{4}$H$_{10}$ and SF$_{6}$ but, starting from 2017, new EU regulations have enforced a progressive phase-out of C$_{2}$H$_{2}$F$_{4}$ because of its large Global Warming Potential (GWP), making it difficult and costly to purchase. CERN asked LHC experiments to reduce greenhouse gases emissions, to which RPC operation contributes significantly. A possible candidate for C$_{2}$H$_{2}$F$_{4}$ replacement is the C$_{3}$H$_{2}$F$_{4}$ (diluted with other gases, such as CO$_{2}$), which has been extensively tested using cosmic rays. Promising gas mixtures have been devised; the next crucial steps are the detailed in-beam characterization of such mixtures as well as the study of their performance under increasing irradiation levels. This contribution will describe the methodology and results of beam tests carried out at the CERN GIF++ (equipped with a high activity $^{137}$Cs source and muon beam) with an ALICE-like RPC prototype, operated with several mixtures with varying proportions of CO$_{2}$, C$_{3}$H$_{2}$F$_{4}$, i-C$_{4}$H$_{10}$ and SF$_{6}$ . Absorbed currents, efficiencies, prompt charges, cluster sizes, time resolutions and rate capabilities will be presented, both from digitized (for detailed shape and charge analysis) and discriminated (using the same front-end electronics as employed in ALICE) signals.

hep-ex↗

arXiv2024

Exploring Eco-Friendly Gas Mixtures for Resistive Plate Chambers: A Comprehensive Study on Performance and Aging

Resistive Plate Chambers (RPCs) are gaseous detectors widely used in high energy physics experiments, operating with a gas mixture primarily containing Tetrafluoroethane (C$_{2}$H$_{2}$F$_{4}$), commonly known as R-134a, which has a global warming potential (GWP) of 1430. To comply with European regulations and explore environmentally friendly alternatives, the RPC EcoGas@GIF++ collaboration, involving ALICE, ATLAS, CMS, LHCb/SHiP, and EP-DT communities, has undertaken intensive R\&D efforts to explore new gas mixtures for RPC technology. A leading alternative under investigation is HFO1234ze, boasting a low GWP of 6 and demonstrating reasonable performance compared to R-134a. Over the past few years, RPC detectors with slightly different characteristics and electronics have been studied using HFO and CO$_{2}$-based gas mixtures at the CERN Gamma Irradiation Facility. An aging test campaign was launched in August 2022, and during the latest test beam in July 2023, all detector systems underwent evaluation. This contribution will report the results of the aging studies and the performance evaluations of the detectors with and without irradiation.

physics.ins-det↗