arXiv subjects

G. Verde

Publications and source records attributed to G. Verde.

At least 55 records · Page 3Linked to original sources

arXiv2019

The FAZIA setup: a review on the electronics and the mechanical mounting

In this paper the technological aspects of the FAZIA array will be explored. After a productive commissioning phase, FAZIA blocks started to measure and give very useful data to explore the physics of Fermi energy heavy-ion reactions. This was possible thanks to many technical measures and innovations developed in the commissioning phase and tuned during the first experimental campaigns. This paper gives a detailed description of the present status of the FAZIA setup from the electronic and mechanical point of view, trying also to trace a path for new improvements and refinements of the apparatus.

physics.ins-det↗

arXiv2019

Non-linearity effects on the light-output calibration of light charged particles in CsI(Tl) scintillator crystals

The light output produced by light ions (Z<=4) in CsI(Tl) crystals is studied over a wide range of detected energies (E<=300 MeV). Energy-light calibration data sets are obtained with the 10 cm crystals in the recently upgraded High-Resolution Array (HiRA10). We use proton recoil data from 40,48Ca + CH2 at 28 MeV/u, 56.6 MeV/u, 39 MeV/u and 139.8 MeV/u and data from a dedicated experiment with direct low-energy beams. We also use the punch through points of p, d, and t particles from 40,48Ca + 58,64Ni, 112,124Sn collisions reactions at 139.8 MeV/u. Non-linearities, arising in particular from Tl doping and light collection efficiency in the CsI crystals, are found to significantly affect the light output and therefore the calibration of the detector response for light charged particles, especially the hydrogen isotopes. A new empirical parametrization of the hydrogen light output, L(E,Z=1,A), is proposed to account for the observed effects. Results are found to be consistent for all 48 CsI(Tl) crystals in a cluster of 12 HiRA10 telescopes.

physics.ins-det↗

arXiv2019

Distillation and stripping pilot plants for the JUNO neutrino detector: design, operations and reliability

This paper describes the design, construction principles and operations of the distillation and stripping pilot plants tested at the Daya Bay Neutrino Laboratory, with the perspective to adapt this processes, system cleanliness and leak-tightness to the final full scale plants that will be used for the purification of the liquid scintillator used in the JUNO neutrino detector. The main goal of these plants is to remove radio impurities from the liquid scintillator while increasing its optical attenuation length. Purification of liquid scintillator will be performed with a system combining alumina oxide, distillation, water extraction and steam (or N2 gas) stripping. Such a combined system will aim at obtaining a total attenuation length greater than 20 m at 430 nm, and a bulk radiopurity for 238U and 232Th in the 10-15 to 10-17 g/g range. The pilot plants commissioning and operation have also provided valuable information on the degree of reliability of their main components, which will be particularly useful for the design of the final full scale purification equipment for the JUNO liquid scintillator. This paper describe two of the five pilot plants since the Alumina Column, Fluor mixing and the Water Extraction plants are in charge of the Chinese part of the collaboration.

physics.ins-det↗

arXiv2019

GIGJ: a crustal gravity model of the Guangdong Province for predicting the geoneutrino signal at the JUNO experiment

Gravimetric methods are expected to play a decisive role in geophysical modeling of the regional crustal structure applied to geoneutrino studies. GIGJ (GOCE Inversion for Geoneutrinos at JUNO) is a 3D numerical model constituted by ~46 x 10$^{3}$ voxels of 50 x 50 x 0.1 km, built by inverting gravimetric data over the 6° x 4° area centered at the Jiangmen Underground Neutrino Observatory (JUNO) experiment, currently under construction in the Guangdong Province (China). The a-priori modeling is based on the adoption of deep seismic sounding profiles, receiver functions, teleseismic P-wave velocity models and Moho depth maps, according to their own accuracy and spatial resolution. The inversion method allowed for integrating GOCE data with the a-priori information and regularization conditions through a Bayesian approach and a stochastic optimization. GIGJ fits the homogeneously distributed GOCE gravity data, characterized by high accuracy, with a ~1 mGal standard deviation of the residuals, compatible with the observation accuracy. Conversely to existing global models, GIGJ provides a site-specific subdivision of the crustal layers masses which uncertainties include estimation errors, associated to the gravimetric solution, and systematic uncertainties, related to the adoption of a fixed sedimentary layer. A consequence of this local rearrangement of the crustal layer thicknesses is a ~21% reduction and a ~24% increase of the middle and lower crust expected geoneutrino signal, respectively. Finally, the geophysical uncertainties of geoneutrino signals at JUNO produced by unitary uranium and thorium abundances distributed in the upper, middle and lower crust are reduced by 77%, 55% and 78%, respectively. The numerical model is available at http://www.fe.infn.it/u/radioactivity/GIGJ

physics.geo-ph↗

arXiv2018

Nanoseconds Timing System Based on IEEE 1588 FPGA Implementation

Clock synchronization procedures are mandatory in most physical experiments where event fragments are readout by spatially dislocated sensors and must be glued together to reconstruct key parameters (e.g. energy, interaction vertex etc.) of the process under investigation. These distributed data readout topologies rely on an accurate time information available at the frontend, where raw data are acquired and tagged with a precise timestamp prior to data buffering and central data collecting. This makes the network complexity and latency, between frontend and backend electronics, negligible within upper bounds imposed by the frontend data buffer capability. The proposed research work describes an FPGA implementation of IEEE 1588 Precision Time Protocol (PTP) that exploits the CERN Timing, Trigger and Control (TTC) system as a multicast messaging physical and data link layer. The hardware implementation extends the clock synchronization to the nanoseconds range, overcoming the typical accuracy limitations inferred by computers Ethernet based Local Area Network (LAN). Establishing a reliable communication between master and timing receiver nodes is essential in a message-based synchronization system. In the backend electronics, the serial data streams synchronization with the global clock domain is guaranteed by an hardware-based finite state machine that scans the bit period using a variable delay chain and finds the optimal sampling point. The validity of the proposed timing system has been proved in point-to-point data links as well as in star topology configurations over standard CAT-5e cables. The results achieved together with weaknesses and possible improvements are hereby detailed.

cs.NI↗

arXiv2018

Phase transition dynamics for hot nuclei

An abnormal production of events with almost equal-sized fragments was theoretically proposed as a signature of spinodal instabilities responsible for nuclear multifragmentation in the Fermi energy domain. On the other hand finite size effects are predicted to strongly reduce this abnormal production. High statistics quasifusion hot nuclei produced in central collisions between Xe and Sn isotopes at 32 and 45 AMeV incident energies have been used to definitively establish, through the experimental measurement of charge correlations, the presence of spinodal instabilities. N/Z influence was also studied.

nucl-ex↗

arXiv2018

Study and validation of a new "3D Calorimetry" of hot nuclei with the HIPSE event generator

In nuclear thermodynamics, the determination of the excitation energy of hot nuclei is a fundamental experimental problem. Instrumental physicists have been trying to solve this problem for several years by building the most exhaustive 4Pi detector arrays and perfecting their calorimetry techniques. In a recent paper, a proposal for a new calorimetry, called "3D calorimetry", was made. It tries to optimize the separation between the particles and fragments emitted by the Quasi-Projectile and the other possible contributions. This can be achieved by determining the experimental probability for a given nucleus of a nuclear reaction to be emitted by the Quasi-Projectile. It has been developed for the INDRA data. In the present work, we wanted to dissect and validate this new method of characterization of a hot Quasi-Projectile. So we tried to understand and control it completely to determine these limits. Using the HIPSE event generator and a software simulating the functioning of INDRA, we were able to achieve this goal and provide a quantitative estimation of the quality of the QP characterization.

nucl-ex↗

arXiv2018

Isospin influence on dynamical production of Intermediate Mass Fragments at Fermi Energies

The Intermediate Mass Fragments emission probability from Projectile-Like Fragment break-up in semi-peripheral reactions has been measured in collisions of $^{124}$Xe projectiles with two different targets of $^{64}$Ni and $^{64}$Zn at the laboratory energy of 35 \amev. The two colliding systems differ only for the target atomic number Z and, consequently, for the Isospin $N/Z$ ratio. An enhancement of Intermediate Mass Fragments production for the neutron rich $^{64}$Ni target, with respect to the $^{64}$Zn, is found. In the case of one Intermediate Mass Fragment emission, the contributions of the dynamical and statistical emissions have been evaluated, showing that the increase of the effect above is due to an enhancement of the dynamical emission probability, especially for heavy IMFs (Z$\gtrsim$ 7). This proves an influence of the target Isospin on inducing the dynamical fragment production from Projectile-Like Fragment break-up. In addition, a comparison of the Xe+Ni,Zn results with the previously studied $^{112,124}Sn+^{58,64}Ni$ systems is discussed in order to investigate the influence of the projectile Isospin alone and to disentangle between Isospin effects against system-size effects on the emission probability. These comparisons suggest that the prompt-dynamical emission is mainly ruled by the $N/Z$ content of, both, projectile and target; for the cases here investigated, the influence of the system size on the dynamical emission probability can be excluded.

nucl-ex↗

arXiv2018

Charge reconstruction in large-area photomultipliers

Large-area PhotoMultiplier Tubes (PMT) allow to efficiently instrument Liquid Scintillator (LS) neutrino detectors, where large target masses are pivotal to compensate for neutrinos' extremely elusive nature. Depending on the detector light yield, several scintillation photons stemming from the same neutrino interaction are likely to hit a single PMT in a few tens/hundreds of nanoseconds, resulting in several photoelectrons (PEs) to pile-up at the PMT anode. In such scenario, the signal generated by each PE is entangled to the others, and an accurate PMT charge reconstruction becomes challenging. This manuscript describes an experimental method able to address the PMT charge reconstruction in the case of large PE pile-up, providing an unbiased charge estimator at the permille level up to 15 detected PEs. The method is based on a signal filtering technique (Wiener filter) which suppresses the noise due to both PMT and readout electronics, and on a Fourier-based deconvolution able to minimize the influence of signal distortions ---such as an overshoot. The analysis of simulated PMT waveforms shows that the slope of a linear regression modeling the relation between reconstructed and true charge values improves from $0.769 \pm 0.001$ (without deconvolution) to $0.989 \pm 0.001$ (with deconvolution), where unitary slope implies perfect reconstruction. A C++ implementation of the charge reconstruction algorithm is available online at http://www.fe.infn.it/CRA .

physics.ins-det↗

arXiv2017

A new "3D Calorimetry" of hot nuclei

In the domain of Fermi energy, it is extremely complex to isolate experimentally fragments and particles issued from the cooling of a hot nucleus produced during a heavy ion collision. This paper presents a new method to characterize more precisely hot Quasi-Projectiles. It tries to take into account as accurately as possible the distortions generated by all the other potential participants in the nuclear reaction. It is quantitatively shown that this method is a major improvement respect to classic calorimetries used with a 4$π$ detector array. By detailing and deconvolving the different steps of the reconstitution of the hot nucleus, this study shows also the respective role played by the experimental device and the event selection criteria on the quality of the determination of QP characteristics.

physics.data-an↗

arXiv2017

Improving isotopic identification with \emph{INDRA} Silicon-CsI(\emph{Tl}) telescopes

Profiting from previous works done with the \emph{INDRA} multidetector on the description of the light response $\mathcal L$ of the CsI(\emph{Tl}) crystals to different impinging nuclei, we propose an improved $ΔE - \mathcal L$ identification-calibration procedure for Silicon-Cesium Iodide (Si-CsI) telescopes, namely an Advanced Mass Estimate (\emph{AME}) method. \emph{AME} is compared to the usual, %$"ΔE - E"$ simple visual analysis of the corresponding two-dimensional map of $ΔE - E$ type, by using \emph{INDRA} experimental data from nuclear reactions induced by heavy ions in the Fermi energy regime. We show that the capability of such telescopes to identify both the atomic $Z$ and the mass $A$ numbers of light and heavy reaction products, can be quantitatively improved thanks to the proposed approach. This conclusion opens new possibilities to use \emph{INDRA} for studying these reactions especially with radioactive beams. Indeed, the determination of the mass for charged reaction products becomes of paramount importance to shed light on the role of the isospin degree of freedom in the nuclear equation of state.

physics.ins-det↗

arXiv2017

Understand the thermometry of hot nuclei from the energy spectra of light charged particles

In the domain of Fermi energy, the hot nucleus temperature can be determined by using the energy spectra of evaporated light charged particles. But this method of measurement is not without difficulties both theoretical and experimental. The presented study aims to disentangle the respective influences of different factors on the quality of this measurement : the physics, the detection (a 4? detector array as INDRA) and the experimental procedure. This analysis demonstrates the possibility of determining from an energy spectrum, with an accuracy of about 10 %, the true apparent temperature felt by a given type of particle emitted by a hot nucleus. Three conditions are however necessary : have a perfect detector of particles, an important statistics and very few secondary emissions. According to the GEMINI event generator, for hot nuclei of intermediate mass, only deuterons and tritons could fill these conditions. This temperature can allow to trace back to the initial temperature by using an appropriate method. This determination may be better than 15 %. With a real experimental device, an insufficient angular resolution and topological distortions caused by the detection can damage spectra to the point to make very difficult a correct determination of the apparent temperature. The experimental reconstruction of the frame of the hot nucleus may also be responsible for this deterioration

nucl-ex↗

arXiv2017

High precision probe of the fully sequential decay width of the Hoyle state in $^{12}$C

The decay path of the Hoyle state in $^{12}$C ($E_x=7.654\textrm{MeV}$) has been studied with the $^{14}\textrm{N}(\textrm{d},α_2)^{12}\textrm{C}(7.654)$ reaction induced at $10.5\textrm{MeV}$. High resolution invariant mass spectroscopy techniques have allowed to unambiguously disentangle direct and sequential decays of the state passing through the ground state of $^{8}$Be. Thanks to the almost total absence of background and the attained resolution, a fully sequential decay contribution to the width of the state has been observed. The direct decay width is negligible, with an upper limit of $0.043\%$ ($95\%$ C.L.). The precision of this result is about a factor $5$ higher than previous studies. This has significant implications on nuclear structure, as it provides constraints to $3$-$α$ cluster model calculations, where higher precision limits are needed.

nucl-ex↗

arXiv2017

Light charged clusters emitted in 32 MeV/nucleon 136,124Xe+124,112Sn reactions: chemical equilibrium, 3He and 6He production

Nuclear particle production from peripheral to central events is presented. N/Z gradient between projectile and target is studied using the fact that two reactions have the same projectile+target N/Z and so the same neutron to proton ratio for the combined system. Inclusive data study in the forward part of the center of mass indicates that N/Z equilibration between the projectile-like and the target-like is achieved for central collisions. Particles are also produced from mid-rapidity region. 3He mean pre-equilibrium character is evidenced and 6He production at mid-rapidity implies a neutron enrichment phenomenon of the projectile target interacting zone.

nucl-ex↗

arXiv2016

Results of the ASY-EOS experiment at GSI: The symmetry energy at suprasaturation density

Directed and elliptic flows of neutrons and light charged particles were measured for the reaction 197Au+197Au at 400 MeV/nucleon incident energy within the ASY-EOS experimental campaign at the GSI laboratory. The detection system consisted of the Large Area Neutron Detector LAND, combined with parts of the CHIMERA multidetector, of the ALADIN Time-of-flight Wall, and of the Washington-University Microball detector. The latter three arrays were used for the event characterization and reaction-plane reconstruction. In addition, an array of triple telescopes, KRATTA, was used for complementary measurements of the isotopic composition and flows of light charged particles. From the comparison of the elliptic flow ratio of neutrons with respect to charged particles with UrQMD predictions, a value γ= 0.72 \pm 0.19 is obtained for the power-law coefficient describing the density dependence of the potential part in the parametrization of the symmetry energy. It represents a new and more stringent constraint for the regime of supra-saturation density and confirms, with a considerably smaller uncertainty, the moderately soft to linear density dependence deduced from the earlier FOPI-LAND data. The densities probed are shown to reach beyond twice saturation.

nucl-ex↗

arXiv2016

Semi-automatic charge and mass identification in two-dimensional matrices

This article presents a new semi-automatic method for charge and mass identification in two-dimensional matrices. The proposed algorithm is based on the matrix's properties and uses as little information as possible on the global form of the identification lines, making it applicable to a large variety of matrices, including Particular attention has been paid to the implementation in a suitable graphical environment, so that only two mouse-clicks are required from the user to calculate all initialization parameters. Example applications to recent data from both INDRA and FAZIA telescopes are presented.

physics.ins-det↗

arXiv2016

Reaction and fusion cross sections for the near-symmetric system $^{129}Xe+^{nat}Sn$ from $8$ to $35$ $AMeV$

\item[Background]Heavy-ion reactions from barrier up to Fermi energy. \item[Purpose]Reaction and fusion cross sections determination. Fusion reactions induced by $^{129}Xe$ projectiles on $^{nat}Sn$ targets for energies ranging from $8$ A.MeV to $35$ A.MeV were measured with the INDRA $4π$-array.\\ The evaluation of the fusion/incomplete fusion cross sections for the incident energies from 8 to 35 A.MeV is the main purpose of this paper. \item[Method] The reaction cross sections are evaluated for each beam energy thanks to INDRA $4π$-array. The events are also sorted in order to focus the study on a selected sample of events, in such a way that the fusion/fusion incomplete cross section is estimated. \item[Results] The excitation function of reaction and fusion cross sections were measured for the heavy and nearly symmetric system $^{129}Xe + ^{nat}Sn$ from 8 to 35 A.MeV. \item[Conclusions] The fusion-like cross-sections evaluated show a good agrement with a recent systematics for beam energies greater than 20 A.MeV. For low beam energies the cross-section values are lower than the expected ones. A probable reason for these low values is in the fusion hindrance at energies above/close the barrier.

nucl-ex↗

arXiv2015

Dipolar degrees of freedom and Isospin equilibration processes in Heavy Ion collisions

Background: In heavy ion collision at the Fermi energies Isospin equilibration processes occur- ring when nuclei with different charge/mass asymmetries interacts have been investigated to get information on the nucleon-nucleon Iso-vectorial effective interaction. Purpose: In this paper, for the system 48Ca +27 Al at 40 MeV/nucleon, we investigate on this process by means of an observable tightly linked to isospin equilibration processes and sensitive in exclusive way to the dynamical stage of the collision. From the comparison with dynamical model calculations we want also to obtain information on the Iso-vectorial effective microscopic interaction. Method: The average time derivative of the total dipole associated to the relative motion of all emitted charged particles and fragments has been determined from the measured charges and velocities by using the 4? multi-detector CHIMERA. The average has been determined for semi- peripheral collisions and for different charges Zb of the biggest produced fragment. Experimental evidences collected for the systems 27Al+48Ca and 27Al+40Ca at 40 MeV/nucleon used to support this novel method of investigation are also discussed.

nucl-ex↗