arXiv subjects

Gerard J. Verbiest

Publications and source records attributed to Gerard J. Verbiest.

13 recordsLinked to original sources

arXiv2025

Optomechanical method for characterizing thermal transport across van der Waals interfaces

For the development of nanoscale electronics and photonics using atomically thin two-dimensional (2D) materials, it is important to realize van der Waals (vdW) interfaces with low thermal resistance, to minimize performance reduction caused by heat accumulation. However, characterizing the thermal interface resistance between vdW materials is still a challenge. Here, we introduce a novel optomechanical methodology to characterize the thermal transport across interfaces in 2D heterostructures. We first determine the specific heat and thermal conductivity as the function of temperature for the upper and lower material layers separately and then extract the thermal boundary conductance (TBC) of the heterostructure from its thermal time constant. We obtain a TBC of $2.41 \pm 1.03$ and $4.14 \pm 1.74$~\si{MW m^{2} K^{-1}} for FePS$_3$/WSe$_2$ and MoS$_2$/FePS$_3$ interfaces, respectively, which are comparable to values reported in the literature. Moreover, they agree with a Debye model including the acoustic impedance mismatch of flexural phonons. This work enables efficient thermal management down to the nanoscale and offers new insights into energy dissipation in vdW heterostructures.

physics.app-ph↗

arXiv2025

Amorphous Silicon-Carbide Photonics for Ultrasound Imaging

Photonic ultrasound sensors offer unparalleled potential for improving spatial and temporal resolution in ultrasound imaging applications due to their size-independent noise figure, high sensitivity, and broad bandwidth characteristics. The exploration of optical materials in ultrasound sensing has attracted significant interest due to their potential to further enhance device performance, fabrication compatibility, and long-term stability. This work introduces amorphous silicon carbide (a-SiC) as a material for optical ultrasound sensing. a-SiC offers a balanced combination of optical confinement, low propagation loss, and high material stability, enabling sensitive and miniaturized microring sensors. We demonstrate a compact ultrasound detection system with a linear array of 20 transducers coupled to a single bus waveguide. The sensors feature a maximum optical finesse of 1320 and an intrinsic platform sensitivity of 78 fm/kPa, leading to a noise equivalent pressure density below 55 $\mathrm{mPa}/\sqrt{\mathrm{Hz}}$, which is calibrated to a hydrophone from 3.36 MHz to 30 MHz. Additionally, we perform high-resolution ultrasound imaging of fine structures, highlighting the viability of these sensors in real-world applications. Moreover, its low deposition temperature allows a-SiC material for optical ultrasound sensors to be integrated on most substrates. These results position a-SiC as a promising material for optical ultrasound sensing, offering a miniaturized, low-loss, and high-sensitivity solution for next-generation photoacoustic imaging applications.

physics.optics↗

arXiv2024

Actuation and mapping of SAW-induced high-frequency wavefields on suspended graphene membranes

High frequency acoustic devices based on two-dimensional (2D) materials are unique platforms to design and manipulate the spatiotemporal response of acoustic waves for next-generation sensing and contactless actuation applications. Conventional methods for actuating suspended membranes, however, cannot be applied to all 2D materials, or are limited in frequency. There is, therefore, a need for a universal high-frequency, on-chip actuation technique that can be applied to all types of membranes. Here, we demonstrate that surface acoustic waves (SAWs) can be used to efficiently actuate suspended 2D materials by exciting suspended graphene membranes with high-frequency (375 MHz) Rayleigh surface waves and mapping the resulting vibration field with atomic force acoustic microscopy (AFAM). Acoustic waves travelling from supported to suspended graphene experience a reduction in acoustic wavelength from 10 μm to ~2 μum due to the decrease in effective bending rigidity, leading to a decrease in wave velocity on suspended graphene. By varying the excitation frequency, we observed a change in phase velocity from ~160 m/s to ~700 m/s. This behavior is consistent with the nonlinear dispersion of acoustic waves, as predicted by plate theory, in suspended graphene membranes. The geometry and bending rigidity of the membrane thus play key roles in modulating the acoustic wave pattern and wavelength. This combined SAW actuation and AFAM visualization scheme can give new insights into the fundamentals of acoustic transport at the nanoscale limit and provides a route towards the manipulation of localized wavefields for on-chip patterning and transport over 2D materials surfaces.

cond-mat.mes-hall↗

arXiv2023

Optomechanical methodology for characterizing the thermal properties of 2D materials

Heat transport in two-dimensions is fundamentally different from that in three dimensions. As a consequence, the thermal properties of 2D materials are of great interest, both from scientific and application point of view. However, few techniques are available for accurate determination of these properties in ultrathin suspended membranes. Here, we present an optomechanical methodology for extracting the thermal expansion coefficient, specific heat and thermal conductivity of ultrathin membranes made of 2H-TaS2, FePS3, polycrystalline silicon, MoS2 and WSe2. The obtained thermal properties are in good agreement with values reported in the literature for the same materials. Our work provides an optomechanical method for determining thermal properties of ultrathin suspended membranes, that are difficult to measure otherwise. It can does provide a route towards improving our understanding of heat transport in the 2D limit and facilitates engineering of 2D structures with dedicated thermal performance.

physics.app-ph↗

arXiv2023

Enhanced sensitivity and tunability of thermomechanical resonance near the buckling bifurcation

The high susceptibility of ultrathin two-dimensional (2D) material resonators to force and temperature makes them ideal systems for sensing applications and exploring thermomechanical coupling. Although the dynamics of these systems at high stress has been thoroughly investigated, their behavior near the buckling transition has received less attention. Here, we demonstrate that the force sensitivity and frequency tunability of 2D material resonators are significantly enhanced near the buckling bifurcation. This bifurcation is triggered by compressive displacement that we induce via thermal expansion of the devices, while measuring their dynamics via an optomechanical technique. We understand the frequency tuning of the devices through a mechanical buckling model, which allows to extract the central deflection and boundary compressive displacement of the membrane. Surprisingly, we obtain a remarkable enhancement of up to 14x the vibration amplitude attributed to a very low stiffness of the membrane at the buckling transition, as well as a high frequency tunability by temperature of more than 4.02 %/K. The presented results provide insights into the effects of buckling on the dynamics of free-standing 2D materials and thereby open up opportunities for the realization of 2D resonant sensors with buckling-enhanced sensitivity.

cond-mat.mes-hall↗

arXiv2023

Quantifying stress distribution in ultra-large graphene drums through mode shape imaging

Suspended drums made of 2D materials hold potential for sensing applications. However, the industrialization of these applications is hindered by significant device-to-device variations presumably caused by non-uniform stress distributions induced by the fabrication process. Here we introduce a new methodology to determine the stress distribution from their mechanical resonance frequencies and corresponding mode shapes as measured by a laser Doppler vibrometer (LDV). To avoid limitations posed by the optical resolution of the LDV, we leverage a unique manufacturing process to create ultra-large graphene drums with diameters of up to 1000 um. We solve the inverse problem of a Föppl--von Kármán plate model by an iterative procedure to obtain the stress distribution within the drums from the experimental data. Our results show that the generally used uniform pre-tension assumption overestimates the pre-stress value, exceeding the averaged stress obtained by more than 47%. Moreover, it is is found that the reconstructed stress distributions are bi-axial, which likely originates from the transfer process. The introduced metholodogy allows one to estimate the tension distribution in drum resonators from their mechanical response and thereby paves the way for linking the used fabrication processes to the resulting device performance.

physics.app-ph↗

arXiv2022

Ultra-sensitive graphene membranes for microphone applications

Microphones exploit the motion of suspended membranes to detect sound waves. Since the microphone performance can be improved by reducing the thickness and mass of its sensing membrane, graphene-based microphones are expected to outperform state-of-the-art microelectromechanical (MEMS) microphones and allow further miniaturization of the device. Here, we present a laser vibrometry study of the acoustic response of suspended multilayer graphene membranes for microphone applications. We address performance parameters relevant for acoustic sensing, including mechanical sensitivity, limit of detection and nonlinear distortion, and discuss the trade-offs and limitations in the design of graphene microphones. We demonstrate superior mechanical sensitivities of the graphene membranes, reaching more than 2 orders of magnitude higher compliances than commercial MEMS devices, and report a limit of detection as low as 15 dBSPL, which is 10 - 15 dB lower than that featured by current MEMS microphones.

physics.app-ph↗

arXiv2022

Conoscopic interferometry for optimal acoustic pulse detection in ultrafast acoustics

Conoscopic interferometry is a promising detection technique for ultrafast acoustics. By focusing a probe beam through a birefringent crystal before passing it through a polarizer, conoscopic interferences sculpt the spatial profile of the beam. The use of these patterns for acoustic wave detection revealed a higher detection sensitivity over existing techniques, such as reflectometry and beam distortion detection. However, the physical origin of the increased sensitivity is unknown. In this work, we present a model, describing the sensitivity behaviour of conoscopic interferometry with respect to the quarter-wave plate orientation and the diaphragm aperture, which is validated experimentally. Using the model, we optimize the detection sensitivity of conoscopic interferometry. We obtain a maximal sensitivity of detection when placing the diaphragm edge on the dark fringes of the conoscopic interference patterns. In the configurations studied in this work, conoscopic interferometry can be 8x more sensitive to acoustic waves than beam distortion detection.

physics.app-ph↗

arXiv2021

Self-sealing complex oxide resonators

Although 2D materials hold great potential for next-generation pressure sensors, recent studies revealed that gases permeate along the membrane-surface interface that is only weakly bound by van der Waals interactions, necessitating additional sealing procedures. In this work, we demonstrate the use of free-standing complex oxides as self-sealing membranes that allow the reference cavity of pressure sensors to be sealed by a simple anneal. To test the hermeticity, we study the gas permeation time constants in nano-mechanical resonators made from SrRuO3 and SrTiO3 membranes suspended over SiO2/Si cavities which show an improvement up to 4 orders of magnitude in the permeation time constant after annealing the devices for 15 minutes. Similar devices fabricated on Si3N4/Si do not show such improvements, suggesting that the adhesion increase over SiO2 is mediated by oxygen bonds that are formed at the SiO2/complex oxide interface during the self-sealing anneal. We confirm the enhancement of adhesion by picosecond ultrasonics measurements which show an increase in the interfacial stiffness by 70% after annealing. Since it is straigthforward to apply, the presented self-sealing method is thus a promising route toward realizing ultrathin hermetic pressure sensors.

cond-mat.mtrl-sci↗

arXiv2020

Optical absorption sensing with dual-spectrum silicon LEDs in SOI-CMOS technology

Silicon p-n junction diodes emit low-intensity, broad-spectrum light near 1120 nm in forward bias and between 400-900 nm in reverse bias (avalanche). For the first time, we experimentally achieve optical absorption sensing of pigment in solution with silicon micro LEDs designed in a standard silicon-on-insulator CMOS technology. By driving a single LED in both forward and avalanche modes of operation, we steer its electroluminescent spectrum between visible and near-infrared (NIR). We then characterize the vertical optical transmission of both visible and NIR light from the LED through the same micro-droplet specimen to a vertically mounted discrete silicon photodiode. The effective absorption coefficient of carmine solution in glycerol at varying concentrations were extracted from the color ratio in optical coupling. By computing the LED-specific molar absorption coefficient of carmine, we estimate the concentration (0.040 mo/L) and validate the same with a commercial spectrophotometer (0.030 mol/L ). With a maximum observed sensitivity of 1260 /cm /mol L, the sensor is a significant step forward towards low-cost CMOS-integrated optical sensors with silicon LED as the light source intended for biochemical analyses in food sector and plant/human health.

physics.optics↗

arXiv2020

Nanoelectromechanical Sensors based on Suspended 2D Materials

The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different sensing concepts and give an overview of the relevant material properties, fabrication routes, and device operation principles. Finally, we discuss sensor readout and integration methods and provide comparisons against the state of the art to show both the challenges and promises of 2D material-based nanoelectromechanical sensing.

physics.app-ph↗

arXiv2019

Phonon Scattering at Kinks in Suspended Graphene

Recent experiments have shown surprisingly large thermal time constants in suspended graphene ranging from 10 to 100 ns in drums with a diameter ranging from 2 to 7 microns. The large time constants and their scaling with diameter points towards a thermal resistance at the edge of the drum. However, an explanation of the microscopic origin of this resistance is lacking. Here, we show how phonon scattering at a kink in the graphene, e.g. formed by sidewall adhesion at the edge of the suspended membrane, can cause a large thermal time constant. This kink strongly limits the fraction of flexural phonons that cross the suspended graphene edge, which causes a thermal interface resistance at its boundary. Our model predicts thermal time constants that are of the same order of magnitude as experimental data, and shows a similar dependence on the circumference. Furthermore, the model predicts the relative in-plane and out-of-plane phonon contributions to graphene's thermal expansion force, in agreement with experiments. We thus show, that in contrast to conventional thermal (Kapitza) resistance which occurs between two different materials, in 2D materials another type of thermal interface resistance can be geometrically induced in a single material.

cond-mat.mes-hall↗

arXiv2019

Nonequilibrium Thermodynamics of Acoustic Phonons in Suspended Graphene

Recent theory has predicted large temperature differences between the in-plane (LA and TA) and out-of-plane (ZA) acoustic phonon baths in locally-heated suspended graphene. To verify these predictions, and their implications for understanding the nonequilibrium thermodynamics of 2D materials, experimental techniques are needed. Here, we present a method to determine the acoustic phonon bath temperatures from the frequency-dependent mechanical response of suspended graphene to a power modulated laser. The mechanical motion reveals two counteracting contributions to the thermal expansion force, that are attributed to fast positive thermal expansion by the in-plane phonons and slower negative thermal expansion by the out-of-plane phonons. The magnitude of the two forces reveals that the in-plane and flexural acoustic phonons are at very different temperatures in the steady-state, with typically observed values of the ratio $ΔT_{\mathrm{LA+TA}}/ΔT_{\mathrm{ZA}}$ between 0.2 and 3.7. These deviations from the generally used local thermal equilibrium assumption ($ΔT_{\mathrm{LA+TA}}=ΔT_{\mathrm{ZA}}$) can affect the experimental analysis of thermal properties of 2D materials.

cond-mat.mes-hall↗