arXiv subjects

Gerhard Fettweis

Publications and source records attributed to Gerhard Fettweis.

At least 19 recordsLinked to original sources

arXiv2026

Self-Healing 6G Networks-in-Network for Resilient Wireless Communication

Future 6G networks must manage increasingly dynamic radio environments in which multiple autonomous sub-networks (SNs) share frequency resources and adapt to changing operating conditions. In such scenarios, interference from faulty devices or intentional jamming can disrupt ongoing communications, making rapid and autonomous network adaptation essential. This demonstration presents a self-healing networks-in-network (NiN) architecture that closely integrates the detection of spectrum anomalies with dynamic spectrum management. A spectrum scanner continuously monitors the frequency spectrum and forwards detected anomalies to the DSM, which automatically identifies suitable frequency resources and reconfigures the affected SN. During the live demonstration, participants can initiate controlled disruptions and observe the entire adaptation process in real time, from anomaly detection to autonomous frequency reallocation and network recovery. The demonstrator illustrates how integrating spectrum monitoring and resource management into a single control loop can improve the resilience of future NiN implementations and demonstrates a practical approach to autonomous, spectrum-aware networking.

cs.NI↗

arXiv2026

On Runlength Limited Codes for BICM Systems

We study the use of runlength-limited (RLL) block codes in bit-interleaved coded modulation (BICM) systems. In this setting, the RLL code acts as the symbol mapper, whose assignment between input bits and RLL symbols is critical for performance. In this work, we aim at optimizing the assignment scheme of RLL codes. One of the main applications of RLL codes is the mitigation of intersymbol interference (ISI) in systems with coarse quantization. However, channel memory and quantization nonlinearity complicate information theoretic analysis. To enable analytical treatment, we consider a block channel with 1-bit analog-to-digital conversion, modeling the transmission of a single RLL code block. For this channel, we investigate the relationship between the achievable rate in BICM systems-termed BICM capacity-and the RLL code's assignment scheme. Focusing on low signal-to-noise ratios (SNRs), we derive the optimization problem yielding the optimal assignment scheme. By looking at asymptotically large block-lengths, we infer a practical optimization strategy for RLL codes with finite block-length and channels with inter-block interference. Further, we extend this optimization to two-state RLL (TS-RLL) codes, which offer higher code rates than state independent RLL codes. We demonstrate that optimized TS-RLL codes exhibit significant performance improvements over literature counterparts.

cs.IT↗

arXiv2026

Spectrum Anomaly Detection in OFDMA Systems: Simulation Framework and Benchmark Dataset

Wireless connectivity underpins modern society and industry, enabling critical applications such as 5G ultra-reliable low-latency communication (URLLC) for industrial automation. However, the openness of the wireless medium exposes it to spectrum anomalies, including unintentional interference and malicious jamming, which threaten communication and sensing functionalities in 5G and emerging 6G networks. Despite its importance, spectrum anomaly detection research is hindered by a lack of publicly available datasets reflecting real-world scenarios. To address this, we present a benchmark dataset for spectrum anomaly detection in orthogonal frequency-division multiplexing access (OFDMA) systems, a core technology for 5G and beyond. The dataset includes spectrograms generated across a distributed network of sensing units, covering five distinct jammer types, from simple noise to advanced pilot-aware attacks. These anomalies are simulated in an industrial factory environment using a versatile open-source framework developed and published as part of this work, enabling extensibility to new scenarios and interference types. We provide baseline evaluations for supervised and unsupervised learning methods, demonstrating the challenges posed by different jammers and highlighting areas for further research. The dataset and framework support reproducible studies and serve as a foundation for advancing spectrum anomaly detection, with applications extending to network digital twins. By bridging the gap in open dataset availability, this work empowers the research community to validate and compare advanced detection methods for resilient next-generation wireless systems.

eess.SP↗

arXiv2026

Impact of Phase Errors on Distributed NTN Beam Focusing

This paper investigates distributed beam focusing for coordinated satellite constellations with phased arrays, motivated by future non-terrestrial network (NTN) systems. A geometric and channel model is developed by incorporating satellite positions, array orientations, antenna directivity, and polarization effects. Under ideal synchronization, the achievable coherent combining gain is analyzed for different constellation geometries, showing that maximum ratio transmission (MRT) enables quadratic scaling of the received power with the number of satellites. The impact of phase errors caused by residual synchronization, timing, mobility, and localization mismatches is then investigated. Closed-form expressions for the average coherent gain are derived for uniformly distributed timing offsets, demonstrating the transition from coherent to non-coherent combining. The results show that synchronization and timing mismatches reduce the coherent combining gain, while geometry dependent effects govern the resulting spatial focusing behavior. Numerical results further show that linear and circular constellations provide different focusing characteristics and spatial separation capabilities. However, MRT-based focusing results in strong sidelobes and limited spatial division capability, motivating the need for joint analog beamforming and digital precoding optimization to improve spatial selectivity and robustness against mobility and localization errors.

eess.SP↗

arXiv2026

Experimental Comparison of Local and Over-the-Air Phase Calibration for MIMO Arrays

Communication performance and channel estimation accuracy in MIMO systems are known to be limited by hardware impairments. Specifically, the presence of phase impairments, such as phase noise, makes real-time coherent transmission a challenging task. While phase impairment compensation is typically performed at the receiver, practical methods for enabling coherent transmission at the transmitter side remain underexplored. Established methods for OTA calibration of MIMO systems face several limitations such as assumptions of phase stationarity and accurate channel knowledge. In this work, a real-time local phase calibration method is experimentally compared with OTA calibration on a fully digital array of USRP X310 software-defined radios. Using RMS cycle-to-cycle jitter as a metric, it is shown that for low and high synchronization signal bandwidths, both approaches effectively eliminate phase drift and whiten the phase noise. Local calibration achieves higher phase stability and is channel-independent, whereas OTA calibration requires no additional hardware but is sensitive to multipath effects and channel-induced impairments. Practical deployment trade-offs are discussed based on the measurement results.

eess.SP↗

arXiv2026

From Coverage to Sensing: ISAC meets FR3

Future 6G systems are expected to exploit upper midband spectrum in frequency range 3 (FR3) not only for high throughput communications, but also for sensing services such as localization, detection, and situational awareness. The following paper develops a concrete path from today's coverage-oriented deployments to FR3 networks that treat sensing as a native function. We first show how existing FR2 radars can be time-multiplexed and coordinated under a $6$G medium access control as radar-as-a-service, forming a bridge between legacy sensing and network-managed integrated sensing and communications (ISAC). We then propose a hierarchical FR3 beam-alignment strategy in which coarse access occurs at lower frequencies and refinement occurs at upper FR3, and quantify the resulting sensing and communication capabilities via range-angle Cram{\'{e}}r-Rao bounds in the near field. We identify intra- and inter-beam squint phenomena specific to wideband FR3 arrays, and discuss design approaches to mitigate them. On the signal-processing side, we argue that FR3 sensing cannot rely solely on pilot resources and discuss how much sensing information can be extracted from payload resource elements. We further highlight the role of calibrated FR3 channel simulators and real-time models as the core of wireless digital twins for training and evaluating ISAC algorithms, and discuss how massive MIMO and dense or distributed deployments at FR3 naturally act as large reconfigurable sensor arrays.

eess.SP↗

arXiv2026

Energy-Efficient Mobile Communications using an Adaptive Gearbox-PHY under Hardware Constraints

Future mobile networks must achieve substantial improvements in energy efficiency to offset the anticipated traffic growth. Despite this requirement, many discussions regarding physical layer design remain primarily focused on peak data rates and spectral efficiency, even though typical network operation is dominated by low-data-rate regimes. To address this mismatch, the Gearbox-PHY was proposed as an energy-efficient physical layer architecture that dynamically switches between modulation schemes and their associated analog front ends in order to adapt to varying operating requirements. This paper quantifies the achievable energy savings by jointly modeling front end power consumption and hardware-aware spectral efficiency to formulate an energy-per-bit minimization problem. To move beyond idealized assumptions, non-ideal hardware effects, including oscillator phase noise and limited quantizer resolution, are incorporated. These impairments simultaneously affect power consumption and achievable spectral efficiency, thereby introducing trade-offs between front end complexity, hardware non-linearities, spectral efficiency, and energy efficiency. Numerical results demonstrate that the Gearbox-PHY enables significant energy savings, particularly at low data rates. Evaluations with spatially distributed users confirm that gains of up to two orders of magnitude persist in a cellular deployment scenario.

eess.SP↗

arXiv2026

Estimating PLL Phase Noise Parameters from Measurements for System-Level Modeling

In current MIMO mobile communication systems, phase noise can significantly impair performance. To allow for compensation of these impairments, accurate phase noise modeling is necessary. Numerical modeling of the phase noise process at a phase-locked loop (PLL) output is established in the literature and commonly represented by an Ornstein-Uhlenbeck (OU) process. The corresponding spectrum can be represented by a multi-pole/zero model. This work presents a least squares (LS) method for estimating the PLL parameters such as oscillator constants or PLL bandwidth from a measured phase noise spectrum. The method is applied on the MAX2870 and MAX2871 PLL chips and parameter estimates such as oscillator constants and PLL bandwidths are provided. The resulting parameter set enables both time- and frequency-domain numerical simulations.

eess.SP↗

arXiv2026

Proof of Concept: Local TX Real-Time Phase Calibration in MIMO Systems

Channel measurements in MIMO systems hinge on precise synchronization. While methods for time and frequency synchronization are well established, maintaining real-time phase coherence remains an open requirement for many MIMO systems. Phase coherence in MIMO systems is crucial for beamforming in digital arrays and enables precise parameter estimates such as Angle-of-Arrival/Departure. This work presents and validates a simple local real-time phase calibration method for a digital array. We compare two different approaches, instantaneous and smoothed calibration, to determine the optimal interval between synchronization procedures. To quantitatively assess calibration performance, we use two metrics: the average beamforming power loss and the RMS cycle-to-cycle jitter. Our results indicate that both approaches for phase calibration are effective and yield RMS of jitter in the 2.1 ps to 124 fs range for different SDR models. This level of precision enables coherent transmission on commonly available SDR platforms, allowing investigation on advanced MIMO techniques and transmit beamforming in practical testbeds.

eess.SP↗

arXiv2026

Cramer-Rao Bound for Angle of Arrival Estimates in True-Time-Delay Systems

In the context of joint communication and sensing JC&S, the challenge of obtaining accurate parameter estimates is of interest. Parameter estimates, such as the AoA can be utilized for solving the initial access problem, interference mitigation, localization of users or monitoring of the environment and synchronization of MIMO systems. Recently, TTD systems have gained attention for fast beam training during initial access and mitigation of beam squinting. This work derives the CRB for angle estimates in typical TTD systems. Properties of the CRB and the Fisher information are investigated and numerically evaluated. Finally, methods for angle estimation such as ML and established estimators are utilized to solve the angle estimation problem using a uniform linear array.

eess.SP↗

arXiv2025

Deterministic Sort-Free Candidate Pruning for Scalable MIMO Box Decoding

Box Decoding is a sort-free tree-search MIMO detector whose complexity is independent of the QAM order, achieved by searching a fixed candidate box around a zero-forcing (ZF) estimate. However, without pruning, the number of visited nodes grows exponentially with the MIMO dimension, limiting scalability. This work proposes two deterministic, low-complexity, sort-free pruning strategies to control node growth. By exploiting the geometric symmetry of the QAM grid and the relative displacement between the ZF estimate and nearby constellation points, the proposed methods eliminate unnecessary metric evaluations while preserving QAM-order independence. The resulting detector achieves substantial complexity reduction with negligible error-rate degradation and enables fully parallel, hardware-efficient implementations for large-scale MIMO and higher-order QAM systems.

eess.SP↗

arXiv2025

Integrated Radio Sensing Capabilities for 6G Networks: AI/ML Perspective

The sixth-generation wireless communications (6G) is often labeled as "connected intelligence". Radio sensing, aligned with machine learning (ML) and artificial intelligence (AI), promises, among other benefits, breakthroughs in the system's ability to perceive the environment and effectively utilize this awareness. This article offers a tutorial-style survey of AI and ML approaches to enhance the sensing capabilities of next-generation wireless networks. To this end, while staying in the framework of integrated sensing and communication (ISAC), we expand the term "sensing" from radar, via spectrum sensing, to miscellaneous applications of radio sensing like non-cooperative transmitter localization. We formulate the problems, explain the state-of-the-art approaches, and detail AI-based techniques to tackle various objectives in the context of wireless sensing. We discuss the advantages, enablers, and challenges of integrating various sensing capabilities into an envisioned AI-powered multimodal multi-task network. In addition to the tutorial-style core of this work based on direct authors' involvement in 6G research problems, we review the related literature, and provide both a good start for those entering this field of research, and a topical overview for a general reader with a background in wireless communications

eess.SP↗

arXiv2025

A Practical Analysis: Understanding Phase Noise Modelling in Time and Frequency Domain for Phase-Locked Loops

In MIMO systems, the presence of phase noise is a significant factor that can degrade performance. For MIMO testbeds build from SDR devices, phase noise cannot be ignored, particular in applications that require phase synchronization. This is especially relevant in MIMO systems that employ digital beamforming, where precise phase alignment is crucial. Accordingly, accurate phase noise modelling of SDR devices is essential. However, the information provided in data sheets for different SDR models varies widely and is often insufficient for comprehensive characterization of their phase noise performance. While numerical simulations of PLL phase noise behavior are documented in the literature, there is a lack of extensive measurements supported by appropriate system modelling. In this work, we present a practical phase noise modeling methodology applied to an SDR from the USRP X310 series. Based on measurement data, we derive estimates of key PLL performance indicators such as cycle-to-cycle jitter, oscillator constants, and PLL bandwidth. Furthermore, we propose a parametric model for the phase noise PSD of the PLL circuit and provide corresponding parameter estimates. This model can be used for further investigation into the impact of phase noise on MIMO system performance implemented by similar SDR devices.

eess.SP↗

arXiv2024

Key Exchange in the Quantum Era: Evaluating a Hybrid System of Public-Key Cryptography and Physical-Layer Security

Today's information society relies on cryptography to achieve security goals such as confidentiality, integrity, authentication, and non-repudiation for digital communications. Here, public-key cryptosystems play a pivotal role to share encryption keys and create digital signatures. However, quantum computers threaten the security of traditional public-key cryptosystems as they can tame computational problems underlying the schemes, i.e., discrete logarithm and integer factorization. The prospective arrival of capable-enough quantum computers already threatens today's secret communication in terms of their long-term secrecy when stored to be later decrypted. Therefore, researchers strive to develop and deploy alternative schemes. In this work, evaluate a key exchange protocol based on combining public-key schemes with physical-layer security, anticipating the prospect of quantum attacks. If powerful quantum attackers cannot immediately obtain private keys, legitimate parties have a window of short-term secrecy to perform a physical-layer jamming key exchange (JKE) to establish a long-term shared secret. Thereby, the protocol constraints the computation time available to the attacker to break the employed public-key cryptography. In this paper, we outline the protocol, discuss its security, and point out challenges to be resolved.

cs.CR↗

arXiv2024

Toward an AI-enabled Connected Industry: AGV Communication and Sensor Measurement Datasets

This paper presents two wireless measurement campaigns in industrial testbeds: industrial Vehicle-to-vehicle (iV2V) and industrial Vehicle-to-infrastructure plus Sensor (iV2I+), together with detailed information about the two captured datasets. iV2V covers sidelink communication scenarios between Automated Guided Vehicles (AGVs), while iV2I+ is conducted at an industrial setting where an autonomous cleaning robot is connected to a private cellular network. The combination of different communication technologies within a common measurement methodology provides insights that can be exploited by Machine Learning (ML) for tasks such as fingerprinting, line-of-sight detection, prediction of quality of service or link selection. Moreover, the datasets are publicly available, labelled and prefiltered for fast on-boarding and applicability.

cs.NI↗

arXiv2024

Wireless Channel Prediction via Gaussian Mixture Models

In this work, we utilize a Gaussian mixture model (GMM) to capture the underlying probability density function (PDF) of the channel trajectories of moving mobile terminals (MTs) within the coverage area of a base station (BS) in an offline phase. We propose to leverage the same GMM for channel prediction in the online phase. Our proposed approach does not require signal-to-noise ratio (SNR)-specific training and allows for parallelization. Numerical simulations for both synthetic and measured channel data demonstrate the effectiveness of our proposed GMM-based channel predictor compared to state-ofthe-art channel prediction methods.

eess.SP↗

arXiv2024

A Low-Complexity Machine Learning Design for mmWave Beam Prediction

The 3rd Generation Partnership Project (3GPP) is currently studying machine learning (ML) for the fifth generation (5G)-Advanced New Radio (NR) air interface, where spatial and temporal-domain beam prediction are important use cases. With this background, this letter presents a low-complexity ML design that expedites the spatial-domain beam prediction to reduce the power consumption and the reference signaling overhead, which are currently imperative for frequent beam measurements. Complexity analysis and evaluation results showcase that the proposed model achieves state-of-the-art accuracy with lower computational complexity, resulting in reduced power consumption and faster beam prediction. Furthermore, important observations on the generalization of the proposed model are presented in this letter.

eess.SP↗

arXiv2023

Digital Twin of the Radio Environment: A Novel Approach for Anomaly Detection in Wireless Networks

The increasing relevance of resilience in wireless connectivity for Industry 4.0 stems from the growing complexity and interconnectivity of industrial systems, where a single point of failure can disrupt the entire network, leading to significant downtime and productivity losses. It is thus essential to constantly monitor the network and identify any anomaly such as a jammer. Hereby, technologies envisioned to be integrated in 6G, in particular joint communications and sensing (JCAS) and accurate indoor positioning of transmitters, open up the possibility to build a digital twin (DT) of the radio environment. This paper proposes a new approach for anomaly detection in wireless networks enabled by such a DT which allows to integrate contextual information on the network in the anomaly detection procedure. The basic approach is thereby to compare expected received signal strengths (RSSs) from the DT with measurements done by distributed sensing units (SUs). Employing simulations, different algorithms are compared regarding their ability to infer from the comparison on the presence or absence of an anomaly, particular a jammer. Overall, the feasibility of anomaly detection using the proposed approach is demonstrated which integrates in the ongoing research on employing DTs for comprehensive monitoring of wireless networks.

eess.SP↗