arXiv subjects

Giancarlo Ferrari-Trecate

Publications and source records attributed to Giancarlo Ferrari-Trecate.

At least 91 records · Page 5Linked to original sources

arXiv2021

A Data-Driven Convex Programming Approach to Worst-Case Robust Tracking Controller Design

This paper studies finite-horizon robust tracking control for discrete-time linear systems, based on input-output data. We leverage behavioral theory to represent system trajectories through a set of noiseless historical data, instead of using an explicit system model. By assuming that recent output data available to the controller are affected by noise terms verifying a quadratic bound, we formulate an optimization problem with a linear cost and LMI constraints for solving the robust tracking problem without any approximations. Our approach hinges on a parameterization of noise trajectories compatible with the data-dependent system representation and on a reformulation of the tracking cost, which enables the application of the S-lemma. In addition, we propose a method for reducing the computational complexity and demonstrate that the size of the resulting LMIs does not scale with the number of historical data. Finally, we show that the proposed formulation can easily incorporate actuator disturbances as well as constraints on inputs and outputs. The performance of the new controllers is discussed through simulations.

math.OC↗

arXiv2020

Hierarchical Control in Islanded DC Microgrids with Flexible Structures

Hierarchical architectures stacking primary, secondary, and tertiary layers are widely employed for the operation and control of islanded DC microgrids (DCmGs), composed of Distribution Generation Units (DGUs), loads, and power lines. However, a comprehensive analysis of all the layers put together is often missing. In this work, we remedy this limitation by setting out a top-to-bottom hierarchical control architecture. Decentralized voltage controllers attached to DGUs form our primary layer. Governed by an MPC--based Energy Management System (EMS), our tertiary layer generates optimal power references and decision variables for DGUs. In particular, decision variables can turn DGUs ON/OFF and select their operation modes. An intermediary secondary layer translates EMS power references into appropriate voltage signals required by the primary layer. More specifically, to provide a voltage solution, the secondary layer solves an optimization problem embedding power-flow equations shown to be always solvable. Since load voltages are not directly enforced, their uniqueness is necessary for DGUs to produce reference powers handed down by the EMS. To this aim, we deduce a novel uniqueness condition based only on local load parameters. Our control framework, besides being applicable for generic DCmG topologies, can accommodate topological changes caused by EMS commands. Its functioning is validated via simulations on a modified 16-bus DC system.

eess.SY↗

arXiv2020

Consensus-Based Current Sharing and Voltage Balancing in DC Microgrids with Exponential Loads

In this work, we present a novel consensus-based secondary control scheme for current sharing and voltage balancing in DC microgrids, composed of distributed generation units, dynamic RLC lines, and nonlinear ZIE (constant impedance, constant current, and exponential) loads. Situated atop a primary voltage control layer, our secondary controllers have a distributed structure, and utilize information exchanged over a communication network to compute necessary control actions. Besides showing that the desired objectives are always attained in steady state, we deduce sufficient conditions for the existence and uniqueness of an equilibrium point for constant power loads -- E loads with zero exponent. Our control design hinges only on the local parameters of the generation units, facilitating plug-and-play operations. We provide a voltage stability analysis, and illustrate the performance and robustness of our designs via simulations. All results hold for arbitrary, albeit connected, microgrid and communication network topologies.

eess.SY↗

arXiv2020

On Existence of Equilibria, Voltage Balancing, and Current Sharing in Consensus-Based DC Microgrids

In this work, we present new secondary regulators for current sharing and voltage balancing in DC microgrids, composed of distributed generation units, dynamic RLC lines, and nonlinear ZIP (constant impedance, constant current, and constant power) loads. The proposed controllers sit atop a primary voltage control layer, and exchange information over a communication network to perform secondary control actions. We deduce sufficient conditions for the existence and uniqueness of an equilibrium point, and show that the desired objectives are attained in steady state. Our control design requires only the knowledge of local parameters of the generation units, facilitating plug-and-play operations. We provide a voltage stability analysis, and illustrate the performance and robustness of our designs via simulations. All results hold for arbitrary, albeit connected, microgrid and communication network topologies.

eess.SY↗

arXiv2020

Supervised MPC control of large-scale electricity networks via clustering methods

This paper describes a control approach for large-scale electricity networks, with the goal of efficiently coordinating distributed generators to balance unexpected load variations with respect to nominal forecasts. To mitigate the difficulties due to the size of the problem, the proposed methodology is divided in two steps. First, the network is partitioned into clusters, composed of several dispatchable and non dispatchable generators, storage systems, and loads. A clustering algorithm is designed with the aim of obtaining clusters with the following characteristics: (i) they must be compact, keeping the distance between generators and loads as small as possible; (ii) they must be able to internally balance load variations to the maximum possible extent. Once the network clustering has been completed, a two layer control system is designed. At the lower layer, a local Model Predictive Controller is associated to each cluster for managing the available generation and storage elements to compensate local load variations. If the local sources are not sufficient to balance the cluster's load variations, a power request is sent to the supervisory layer, which optimally distributes additional resources available from the other clusters of the network. To enhance the scalability of the approach, the supervisor is implemented relying on a fully distributed optimization algorithm. The IEEE 118-bus system is used to test the proposed design procedure in a non trivial scenario.

eess.SY↗

arXiv2018

Distributed watermarking for secure control of microgrids under replay attacks

The problem of replay attacks in the communication network between Distributed Generation Units (DGUs) of a DC microgrid is examined. The DGUs are regulated through a hierarchical control architecture, and are networked to achieve secondary control objectives. Following analysis of the detectability of replay attacks by a distributed monitoring scheme previously proposed, the need for a watermarking signal is identified. Hence, conditions are given on the watermark in order to guarantee detection of replay attacks, and such a signal is designed. Simulations are then presented to demonstrate the effectiveness of the technique.

eess.SY↗

arXiv2017

A consensus-based secondary control layer for stable current sharing and voltage balancing in DC microgrids

In this paper, we propose a secondary consensus-based control layer for current sharing and voltage balancing in DC microGrids (mGs). To this purpose, we assume that Distributed Generation Units (DGUs) are equipped with decentralized primary controllers guaranteeing voltage stability. This goal can be achieved using, for instance, Plug-and-Play (PnP) regulators. We analyze the behavior of the closed-loop mG by approximating local primary control loops with either unitary gains or first-order transfer functions. Besides proving exponential stability, current sharing, and voltage balancing, we describe how to design secondary controllers in a PnP fashion when DGUs are added or removed. Theoretical results are complemented by simulations, using a 7-DGUs mG implemented in Simulink/PLECS, and experiments on a 3-DGUs mG.

eess.SY↗

arXiv2017

Hierarchical Plug-and-Play Voltage/Current Controller of DC Microgrid Clusters with Grid-Forming/Feeding Converters: Line-independent Primary Stabilization and Leader-based Distributed Secondary Regulation

Considering the structure of dc Microgrids (MGs) composed of grid-forming/feeding converters, a hierarchical Plug-and-Play (PnP) voltage/current control architecture for MG clusters is proposed. In the primary level, a PnP voltage/current controller is proposed to achieve simultaneous voltage support and current feeding function according to local references. In addition, stabilizing controller is characterized by explicit inequalities which are only related to local parameters of a MG. In the secondary level, for the system with interconnection of MGs, a leader-based voltage/current distributed controller is proposed to achieve both voltage and current regulation without specifying the individual setpoints for each MG. The proposed controller requires a communication network and each controller exchanges information with its communication neighbors only. With the proposed controller, each MG can plug-in/out of the system seamlessly, irrespectively of the power line parameters and models of other MGs . The proof of the MG cluster closed-loop stability exploits structured Lyapunov functions, the LaSalle invariance theorem and properties of graph Laplacians. Theoretical results are validated by hardware-in-loop (HiL) tests.

math.OC↗

arXiv2017

Voltage stabilization in DC microgrids: an approach based on line-independent plug-and-play controllers

We consider the problem of stabilizing voltages in DC microGrids (mGs) given by the interconnection of Distributed Generation Units (DGUs), power lines and loads. We propose a decentralized control architecture where the primary controller of each DGU can be designed in a Plug-and-Play (PnP) fashion, allowing the seamless addition of new DGUs. Differently from several other approaches to primary control, local design is independent of the parameters of power lines. Moreover, differently from the PnP control scheme in [1], the plug-in of a DGU does not require to update controllers of neighboring DGUs. Local control design is cast into a Linear Matrix Inequality (LMI) problem that, if unfeasible, allows one to deny plug-in requests that might be dangerous for mG stability. The proof of closed-loop stability of voltages exploits structured Lyapunov functions, the LaSalle invariance theorem and properties of graph Laplacians. Theoretical results are backed up by simulations in PSCAD.

eess.SY↗

arXiv2017

Plug-and-play and coordinated control for bus-connected AC islanded microgrids

This paper presents a distributed control architecture for voltage and frequency stabilization in AC islanded microgrids. In the primary control layer, each generation unit is equipped with a local controller acting on the corresponding voltage-source converter. Following the plug-and-play design approach previously proposed by some of the authors, whenever the addition/removal of a distributed generation unit is required, feasibility of the operation is automatically checked by designing local controllers through convex optimization. The update of the voltage-control layer, when units plug -in/-out, is therefore automatized and stability of the microgrid is always preserved. Moreover, local control design is based only on the knowledge of parameters of power lines and it does not require to store a global microgrid model. In this work, we focus on bus-connected microgrid topologies and enhance the primary plug-and-play layer with local virtual impedance loops and secondary coordinated controllers ensuring bus voltage tracking and reactive power sharing. In particular, the secondary control architecture is distributed, hence mirroring the modularity of the primary control layer. We validate primary and secondary controllers by performing experiments with balanced, unbalanced and nonlinear loads, on a setup composed of three bus-connected distributed generation units. Most importantly, the stability of the microgrid after the addition/removal of distributed generation units is assessed. Overall, the experimental results show the feasibility of the proposed modular control design framework, where generation units can be added/removed on the fly, thus enabling the deployment of virtual power plants that can be resized over time.

eess.SY↗

arXiv2016

Kron reduction methods for plug-and-play control of ac islanded microgrids with arbitrary topology

In this paper, we provide an extension of the scalable algorithm proposed in (Riverso et al., 2015) for the design of Plug-and-Play (PnP) controllers for AC Islanded microGrids (ImGs). The method in (Riverso et al., 2015) assumes DGUs are arranged in a load-connected topology, i.e. loads can appear only at the output terminals of inverters. For handling totally general interconnections of DGUs and loads, we describe an approach based on Kron Reduction (KR), a network reduction method giving an equivalent load-connected model of the original ImG. However, existing KR approaches can fail in preserving the structure of transfer functions representing transmission lines. To avoid this drawback, we introduce an approximate KR algorithm, still capable to represent exactly the asymptotic periodic behavior of electric signals even if they are unbalanced. Our results are backed up with simulations illustrating features of the new KR approach as well as its use for designing PnP controllers in a 21-bus ImG derived from an IEEE test feeder.

eess.SY↗

arXiv2015

A decentralized scalable approach to voltage control of DC islanded microgrids

We propose a new decentralized control scheme for DC Islanded microGrids (ImGs) composed by several Distributed Generation Units (DGUs) with a general interconnection topology. Each local controller regulates to a reference value the voltage of the Point of Common Coupling (PCC) of the corresponding DGU. Notably, off-line control design is conducted in a Plug-and-Play (PnP) fashion meaning that (i) the possibility of adding/removing a DGU without spoiling stability of the overall ImG is checked through an optimization problem; (ii) when a DGU is plugged in or out at most neighbouring DGUs have to update their controllers and (iii) the synthesis of a local controller uses only information on the corresponding DGU and lines connected to it. This guarantee total scalability of control synthesis as the ImG size grows or DGU gets replaced. Yes, under mild approximations of line dynamics, we formally guarantee stability of the overall closed-loop ImG. The performance of the proposed controllers is analyzed simulating different scenarios in PSCAD.

eess.SY↗

arXiv2015

Model predictive controllers for reduction of mechanical fatigue in wind farms

We consider the problem of dispatching WindFarm (WF) power demand to individual Wind Turbines (WT) with the goal of minimizing mechanical stresses. We assume wind is strong enough to let each WTs to produce the required power and propose different closed-loop Model Predictive Control (MPC) dispatching algorithms. Similarly to existing approaches based on MPC, our methods do not require changes in WT hardware but only software changes in the SCADA system of the WF. However, differently from previous MPC schemes, we augment the model of a WT with an ARMA predictor of the wind turbulence, which reduces uncertainty in wind predictions over the MPC control horizon. This allows us to develop both stochastic and deterministic MPC algorithms. In order to compare different MPC schemes and demonstrate improvements with respect to classic open-loop schedulers, we performed simulations using the SimWindFarm toolbox for MatLab. We demonstrate that MPC controllers allow to achieve reduction of stresses even in the case of large installations such as the 100-WTs Thanet offshore WF.

eess.SY↗

arXiv2014

Plug-and-play voltage and frequency control of islanded microgrids with meshed topology

In this paper we propose a new decentralized control scheme for Islanded microGrids (ImGs) composed by the interconnection of Distributed Generation Units (DGUs). Local controllers regulate voltage and frequency at the Point of Common Coupling (PCC) of each DGU and they are able to guarantee stability of the overall ImG. The control design procedure is decentralized, since, besides two global scalar quantities, the synthesis of a local controller uses only information on the corresponding DGU and lines connected to it. Most important, our design procedure enables Plug-and-Play (PnP) operations: when a DGU is plugged in or out, only DGUs physically connected to it have to retune their local controllers. We study the performance of the proposed controllers simulating different scenarios in MatLab/Simulink and using performance indexes proposed in IEEE standards.

eess.SY↗

arXiv2014

Plug-and-play fault diagnosis and control-reconfiguration for a class of nonlinear large-scale constrained systems

This paper deals with a novel Plug-and-Play (PnP) architecture for the control and monitoring of Large-Scale Systems (LSSs). The proposed approach integrates a distributed Model Predictive Control (MPC) strategy with a distributed Fault Detection (FD) architecture and methodology in a PnP framework. The basic concept is to use the FD scheme as an autonomous decision support system: once a fault is detected, the faulty subsystem can be unplugged to avoid the propagation of the fault in the interconnected LSS. Analogously, once the issue has been solved, the disconnected subsystem can be re-plugged-in. PnP design of local controllers and detectors allow these operations to be performed safely, i.e. without spoiling stability and constraint satisfaction for the whole LSS. The PnP distributed MPC is derived for a class of nonlinear LSS and an integrated PnP distributed FD architecture is proposed. Simulation results show the effectiveness and the potential of the general methodology.

eess.SY↗

arXiv2013

Plug-and-Play Model Predictive Control based on robust control invariant sets

In this paper we consider a linear system represented by a coupling graph between subsystems and propose a distributed control scheme capable to guarantee asymptotic stability and satisfaction of constraints on system inputs and states. Most importantly, as in Riverso et al., 2012 our design procedure enables plug-and-play (PnP) operations, meaning that (i) the addition or removal of subsystems triggers the design of local controllers associated to successors to the subsystem only and (ii) the synthesis of a local controller for a subsystem requires information only from predecessors of the subsystem and it can be performed using only local computational resources. Our method hinges on local tube MPC controllers based on robust control invariant sets and it advances the PnP design procedure proposed in Riverso et al., 2012 in several directions. Quite notably, using recent results in the computation of robust control invariant sets, we show how critical steps in the design of a local controller can be solved through linear programming. Finally, an application of the proposed control design procedure to frequency control in power networks is presented.

eess.SY↗

arXiv2013

Plug-and-play distributed state estimation for linear systems

This paper proposes a state estimator for large-scale linear systems described by the interaction of state-coupled subsystems affected by bounded disturbances. We equip each subsystem with a Local State Estimator (LSE) for the reconstruction of the subsystem states using pieces of information from parent subsystems only. Moreover we provide conditions guaranteeing that the estimation errors are confined into prescribed polyhedral sets and converge to zero in absence of disturbances. Quite remarkably, the design of an LSE is recast into an optimization problem that requires data from the corresponding subsystem and its parents only. This allows one to synthesize LSEs in a Plug-and-Play (PnP) fashion, i.e. when a subsystem gets added, the update of the whole estimator requires at most the design of an LSE for the subsystem and its parents. Theoretical results are backed up by numerical experiments on a mechanical system.

eess.SY↗

arXiv2013

Plug-and-Play Decentralized Model Predictive Control

In this paper we consider a linear system structured into physically coupled subsystems and propose a decentralized control scheme capable to guarantee asymptotic stability and satisfaction of constraints on system inputs and states. The design procedure is totally decentralized, since the synthesis of a local controller uses only information on a subsystem and its neighbors, i.e. subsystems coupled to it. We first derive tests for checking if a subsystem can be plugged into (or unplugged from) an existing plant without spoiling overall stability and constraint satisfaction. When this is possible, we show how to automatize the design of local controllers so that it can be carried out in parallel by smart actuators equipped with computational resources and capable to exchange information with neighboring subsystems. In particular, local controllers exploit tube-based Model Predictive Control (MPC) in order to guarantee robustness with respect to physical coupling among subsystems. Finally, an application of the proposed control design procedure to frequency control in power networks is presented.

eess.SY↗