SearcharxivSearch

arXiv subjects

Giulio Colavolpe

Publications and source records attributed to Giulio Colavolpe.

At least 19 recordsLinked to original sources

Phase Noise Detection via Expectation Propagation and Related Algorithms

In the context of signal detection in the presence of an unknown time-varying channel parameter, receivers based on the Expectation Propagation (EP) framework appear to be very promising. EP is a message-passing algorithm based on factor graphs with an inherent ability to combine prior knowledge of system variables with channel observations. This suggests that an effective estimation of random channel parameters can be achieved even with a very limited number of pilot symbols, thus increasing the payload efficiency. However, achieving satisfactory performance often requires ad-hoc adjustments in the way the probability distributions of latent variables - both data and channel parameters - are combined and projected. Here, we apply EP to a classical problem of coded transmission on a strong Wiener phase noise channel, employing soft-input soft-output decoding. We identify its limitations and propose new strategies which reach the performance benchmark while maintaining low complexity, with a primary focus on challenging scenarios where the state-of-the-art algorithms fail.

eess.SP

Detection for Flat-Fading Channels based on Expectation Propagation

This paper aims at tackling the problem of signal detection in flat-fading channels. In this context, receivers based on the expectation propagation framework appear to be very promising although presenting some critical issues. We develop a new algorithm based on this framework where, unlike previous works, convergence is achieved after a single forward-backward pass, without additional inner detector iterations. The proposed message scheduling, together with novel adjustments of the approximating distributions' parameters, allows to obtain significant performance advantages with respect to the state-of-the-art solution. Simulation results show the applicability of this algorithm when sparser pilot configurations have to be adopted and a considerable gain compared to the current available strategies.

eess.SP

Beam-Space MIMO Radar for Joint Communication and Sensing with OTFS Modulation

Motivated by automotive applications, we consider joint radar sensing and data communication for a system operating at millimeter wave (mmWave) frequency bands, where a Base Station (BS) is equipped with a co-located radar receiver and sends data using the Orthogonal Time Frequency Space (OTFS) modulation format. We consider two distinct modes of operation. In Discovery mode, a single common data stream is broadcast over a wide angular sector. The radar receiver must detect the presence of not yet acquired targets and perform coarse estimation of their parameters (angle of arrival, range, and velocity). In Tracking mode, the BS transmits multiple individual data streams to already acquired users via beamforming, while the radar receiver performs accurate estimation of the aforementioned parameters. Due to hardware complexity and power consumption constraints, we consider a hybrid digital-analog architecture where the number of RF chains and A/D converters is significantly smaller than the number of antenna array elements. In this case, a direct application of the conventional MIMO radar approach is not possible. Consequently, we advocate a beam-space approach where the vector observation at the radar receiver is obtained through a RF-domain beamforming matrix operating the dimensionality reduction from antennas to RF chains. Under this setup, we propose a likelihood function-based scheme to perform joint target detection and parameter estimation in Discovery, and high-resolution parameter estimation in Tracking mode, respectively. Our numerical results demonstrate that the proposed approach is able to reliably detect multiple targets while closely approaching the Cramer-Rao Lower Bound (CRLB) of the corresponding parameter estimation problem.

eess.SP

Discrete-time models and performance of phase noise channels

This paper deals with the phase noise affecting communication systems, where local oscillators are employed to obtain reference signals for carrier and timing synchronizations. The most common discrete-time phase noise channel model is analyzed, with the aim to fill the gap between measurements and analytical models. In particular, the power loss and the intersymbol interference due to the presence of phase noise is evaluated with reference to the measurements parameters and to the system bandwidth. Moreover, the impact on the communication systems' performance of the phase noise originating from the oscillator non idealities is considered, in case of free-running and phase-locked oscillators. The proposed analysis allows to extrapolate useful information about the performance of practical systems by investigating the power spectral density of the oscillator phase noise. An expression for the variance of the residual phase error after tracking, which depends on the main parameters of practical oscillators, is derived, and used to study the dependence of the performance on the symbol rate.

cs.IT

Decoding of Variable Length PLH Codes

In this paper, we address the problem of the decoding of variable length physical layer header (PLH) codes. We take as a case study the DVB-S2X standard, and, after selecting a suitable PLH code with variable codeword length, we propose two alternative noncoherent decoding strategies. The proposed decoding strategies allow to estimate the length of the transmitted PLH field, which is unknown at the receiver, jointly with the decoding of the PLH code. We demonstrate that it is possible to achieve an excellent decoding performance while significantly reducing the overhead due to the transmission of the PLH field with respect to a standard fixed-length PLH.

cs.IT

Hybrid Digital-Analog Beamforming and MIMO Radar with OTFS Modulation

Motivated by future automotive applications, we study some joint radar target detection and parameter estimation problems where the transmitter, equipped with a mono-static MIMO radar, wishes to detect multiple targets and then estimate their respective parameters, while simultaneously communicating information data using orthogonal time frequency space (OTFS) modulation. Assuming that the number of radio frequency chains is smaller than the number of antennas over the mmWave frequency band, we design hybrid digital-analog beamforming at the radar transmitter adapted to different operating phases. The first scenario considers a wide angular beam in order to perform the target detection and parameter estimation, while multicasting a common message to all possible active users. The second scenario considers narrow angular beams to send information streams individually to the already detected users and simultaneously keep tracking of their respective parameters. Under this setup, we propose an efficient maximum likelihood scheme combined with hybrid beamforming to jointly perform target detection and parameter estimation. Our numerical results demonstrate that the proposed algorithm is able to reliably detect multiple targets with a sufficient number of antennas and achieves the Cramér-Rao lower bound for radar parameter estimation such as delay, Doppler and angle-of-arrival (AoA).

eess.SP

Joint Radar Target Detection and Parameter Estimation with MIMO OTFS

Motivated by future automotive applications, we study the joint target detection and parameter estimation problem using orthogonal time frequency space (OTFS), a digital modulation format robust to time-frequency selective channels. Assuming the transmitter is equipped with a mono-static MIMO radar, we propose an efficient maximum likelihood based approach to detect targets and estimate the corresponding delay, Doppler, and angle-of-arrival parameters. In order to reduce the computational complexity associated to the high-dimensional search, our scheme proceeds in two steps, i.e., target detection and coarse parameter estimation followed by refined parameter estimation. Interestingly, our numerical results demonstrate that the proposed scheme is able to identify multiple targets if they are separated in at least one domain out of three (delay, Doppler, and angle), while achieving the Cramér-Rao lower bound for the parameter estimation.

eess.SP

On the Effectiveness of OTFS for Joint Radar and Communication

We consider a joint radar estimation and communication system using orthogonal time frequency space (OTFS) modulation. The scenario is motivated by vehicular applications where a vehicle equipped with a mono-static radar wishes to communicate data to its target receiver, while estimating parameters of interest related to this receiver. In a point-to-point communication setting over multi-path time-frequency selective channels, we study the joint radar and communication system from two perspectives, i.e., the radar estimation at the transmitter as well as the symbol detection at the receiver. For the radar estimation part, we derive an efficient approximated Maximum Likelihood algorithm and the corresponding Cramér- Rao lower bound for range and velocity estimation. Numerical examples demonstrate that multi-carrier digital formats such as OTFS can achieve as accurate radar estimation as state-of-the-art radar waveforms such as frequency-modulated continuous wave (FMCW). For the data detection part, we focus on separate detection and decoding and consider a soft-output detector that exploits efficiently the channel sparsity in the Doppler-delay domain. We quantify the detector performance in terms of its pragmatic capacity, i.e. the achievable rate of the channel induced by the signal constellation and the detector soft output. Simulations show that the proposed scheme outperforms concurrent state-of-the-art solutions. Overall, our work shows that a suitable digitally modulated waveform enables to efficiently operate joint radar and communication by achieving full information rate of the modulation and near-optimal radar estimation performance. Furthermore, OTFS appears to be particularly suited to the scope.

cs.IT

Short Non-Binary Low-Density Parity-Check Codes for Phase Noise Channels

This work considers the design of short non-binary low-density parity-check (LDPC) codes over finite fields of order m, for channels with phase noise. In particular, m-ary differential phase-shift keying (DPSK) modulated code symbols are transmitted over an additive white Gaussian noise (AWGN) channel with Wiener phase noise. At the receiver side, non-coherent detection takes place, with the help of a multi-symbol detection algorithm, followed by a non-binary decoding step. Both the detector and decoder operate on a joint factor graph. As a benchmark, finite length bounds and information rate expressions are computed and compared with the codeword error rate (CER) performance, as well as the iterative threshold of the obtained codes. As a result, performance within 1:2 dB from finite-length bounds is obtained, down to a CER of 1e-3.

cs.IT

Single-Carrier Modulation versus OFDM for Millimeter-Wave Wireless MIMO

This paper presents results on the achievable spectral efficiency and on the energy efficiency for a wireless multiple-input-multiple-output (MIMO) link operating at millimeter wave frequencies (mmWave) in a typical 5G scenario. Two different single-carrier modem schemes are considered, i.e., a traditional modulation scheme with linear equalization at the receiver, and a single-carrier modulation with cyclic prefix, frequency-domain equalization and FFT-based processing at the receiver; these two schemes are compared with a conventional MIMO-OFDM transceiver structure. Our analysis jointly takes into account the peculiar characteristics of MIMO channels at mmWave frequencies, the use of hybrid (analog-digital) pre-coding and post-coding beamformers, the finite cardinality of the modulation structure, and the non-linear behavior of the transmitter power amplifiers. Our results show that the best performance is achieved by single-carrier modulation with time-domain equalization, which exhibits the smallest loss due to the non-linear distortion, and whose performance can be further improved by using advanced equalization schemes. Results also confirm that performance gets severely degraded when the link length exceeds 90-100 meters and the transmit power falls below 0 dBW.

cs.IT

Integration of 5G Technologies in LEO Mega-Constellations

3GPP is finalising the first release of the 5G New Radio physical layer. To cope with the demanding 5G requirements on global connectivity and large throughput, Satellite Communications might be a valuable resource to extend and complement terrestrial networks. In this context, we introduce an integrated architecture for 5G-based LEO mega-constellations and assess the impact of large Doppler shifts and delays on both the 5G waveform and the PHY/MAC layer procedures.

cs.NI

Multiuser Detection in Multibeam Satellite Systems: Theoretical Analysis and Practical Schemes

We consider the rates achievable by a user in a multibeam satellite system for unicast applications, and propose alternatives to the conventional single-user symbol-by-symbol detection applied at user terminals. Single-user detection is known to suffer from strong degradation when the terminal is located near the edge of the coverage area of a beam, and when aggressive frequency reuse is adopted. For this reason, we consider multiuser detection, and take into account the strongest interfering signal. We also analyze two additional transmission strategies requiring modifications at medium access control layer. We describe an information-theoretic framework to compare the different strategies by computing the information rate of the user in the reference beam. Furthermore, we analyze the performance of coded schemes that could approach the information-theoretic limits. We show that classical codes from the DVB-S2(X) standard are not suitable when multiuser detection is adopted, and we propose two ways to improve the performance, based on the redesign of the code and of the bit mapping.

cs.IT

Spectral Efficiency of MIMO Millimeter-Wave Links with Single-Carrier Modulation for 5G Networks

Future wireless networks will extensively rely upon bandwidths centered on carrier frequencies larger than 10GHz. Indeed, recent research has shown that, despite the large path-loss, millimeter wave (mmWave) frequencies can be successfully exploited to transmit very large data-rates over short distances to slowly moving users. Due to hardware complexity and cost constraints, single-carrier modulation schemes, as opposed to the popular multi-carrier schemes, are being considered for use at mmWave frequencies. This paper presents preliminary studies on the achievable spectral efficiency on a wireless MIMO link operating at mmWave in a typical 5G scenario. Two different single-carrier modem schemes are considered, i.e. a traditional modulation scheme with linear equalization at the receiver, and a single-carrier modulation with cyclic prefix, frequency-domain equalization and FFT-based processing at the receiver. Our results show that the former achieves a larger spectral efficiency than the latter. Results also confirm that the spectral efficiency increases with the dimension of the antenna array, as well as that performance gets severely degraded when the link length exceeds 100 meters and the transmit power falls below 0dBW. Nonetheless, mmWave appear to be very suited for providing very large data-rates over short distances.

cs.IT

Binary CPMs with Improved Spectral Efficiency

We design new continuous phase modulation (CPM) formats which are based on the combination of a proper precoder with binary input and a ternary CPM. The proposed precoder constrains the signal phase evolution in order to increase the minimum Euclidean distance, and to limit the bandwidth expansion due to the use of a ternary CPM. The resulting schemes are highly spectrally efficient and outperform classical binary and quaternary formats in terms of coded and uncoded performance.

cs.IT

On the Use of Multiple Satellites to Improve the Spectral Efficiency of Broadcast Transmissions

We consider the use of multiple co-located satellites to improve the spectral efficiency of broadcast transmissions. In particular, we assume that two satellites transmit on overlapping geographical coverage areas, with overlapping frequencies. We first describe the theoretical framework based on network information theory and, in particular, on the theory for multiple access channels. The application to different scenarios will be then considered, including the bandlimited additive white Gaussian noise channel with average power constraint and different models for the nonlinear satellite channel. The comparison with the adoption of frequency division multiplexing and with the Alamouti space-time block coding is also provided. The main conclusion is that a strategy based on overlapped signals is the most convenient in the case of no power unbalance, although it requires the adoption of a multiuser detection strategy at the receiver.

cs.IT

Optical Time-Frequency Packing: Principles, Design, Implementation, and Experimental Demonstration

Time-frequency packing (TFP) transmission provides the highest achievable spectral efficiency with a constrained symbol alphabet and detector complexity. In this work, the application of the TFP technique to fiber-optic systems is investigated and experimentally demonstrated. The main theoretical aspects, design guidelines, and implementation issues are discussed, focusing on those aspects which are peculiar to TFP systems. In particular, adaptive compensation of propagation impairments, matched filtering, and maximum a posteriori probability detection are obtained by a combination of a butterfly equalizer and four 8-state parallel Bahl-Cocke-Jelinek-Raviv (BCJR) detectors. A novel algorithm that ensures adaptive equalization, channel estimation, and a proper distribution of tasks between the equalizer and BCJR detectors is proposed. A set of irregular low-density parity-check codes with different rates is designed to operate at low error rates and approach the spectral efficiency limit achievable by TFP at different signal-to-noise ratios. An experimental demonstration of the designed system is finally provided with five dual-polarization QPSK-modulated optical carriers, densely packed in a 100 GHz bandwidth, employing a recirculating loop to test the performance of the system at different transmission distances.

physics.optics

On the Application of Multiuser Detection in Multibeam Satellite Systems

We study the achievable rates by a single user in multibeam satellite scenarios. We show alternatives to the conventional symbol-by-symbol detection applied at user terminals. Single user detection is known to suffer from strong degradation when the terminal is located near the edge of the coverage area, and when aggressive frequency reuse is adopted. For this reason, we consider multiuser detection, and take into account the strongest interfering signal. Moreover, we analyze a different transmission strategy, where the signals from two adjacent beams jointly serve two users in a time division multiplexing fashion. We describe an information-theoretic framework to compare different transmission/detection strategies by computing the information rate of the user in the reference beam.

cs.IT

Spectral Efficiency Optimization in Flexi-Grid Long-Haul Optical Systems

Flexible grid optical networks allow a better exploitation of fiber capacity, by enabling a denser frequency allocation. A tighter channel spacing, however, requires narrower filters, which increase linear intersymbol interference (ISI), and may dramatically reduce system reach. Commercial coherent receivers are based on symbol by symbol detectors, which are quite sensitive to ISI. In this context, Nyquist spacing is considered as the ultimate limit to wavelength-division multiplexing (WDM) packing. In this paper, we show that by introducing a limited-complexity trellis processing at the receiver, either the reach of Nyquist WDM flexi-grid networks can be significantly extended, or a denser-than-Nyquist channel packing (i.e., a higher spectral efficiency (SE)) is possible at equal reach. By adopting well-known information-theoretic techniques, we design a limited-complexity trellis processing and quantify its SE gain in flexi-grid architectures where wavelength selective switches over a frequency grid of 12.5GHz are employed.

cs.IT