arXiv subjects

Graeme Smecher

Publications and source records attributed to Graeme Smecher.

At least 19 recordsLinked to original sources

arXiv2026

Tunable responsivity and bandwidth in microwave kinetic inductance detectors via readout current nonlinearity

Microwave kinetic inductance detectors (MKIDs) are generally read out with microwave readout tones of high enough amplitude to adequately suppress the noise contribution of the first-stage amplifier. At high readout power, the detector's resonant frequency is altered as a result of the dependence of the kinetic inductance on the internally circulating microwave current. With the tone placed below the resonant frequency, the nonlinear frequency shift results in a positive feedback effect that can significantly enhance the responsivity of the detector, to both optical and microwave power. We report a factor of 10 enhancement in optical response by tuning the readout power and frequency to close to the resonator's bifurcation point. A corresponding decrease in the bandwidth of the resonator is observed under these conditions. We show that the strength of the feedback effect can be easily selected by adjusting the excitation, and provide a map of possible operational states to do so. Operation of MKIDs in this mode could be used to improve sensitivity when non-intrinsic noise sources are significant.

cond-mat.supr-con↗

arXiv2026

A High-Bandwidth Backplane for Wideband Radio Interferometers and Integration with the CHORD Telescope Correlators

Wide-band correlators for radio astronomy interferometers demand accurate, scalable signal processing backends that sustain high aggregate throughput while preserving stable timing alignment across a large number of signal chains. Addressing these coupled constraints is challenging without a co-designed backplane architecture. We present a backplane system developed for the Control Readout System (CRS) Field Programmable Gate Array (FPGA) platform, extending its capabilities to support high channel count wideband radio correlators. The design and validation process are guided by the requirements of the Canadian Hydrogen Observatory and Radio-transient Detector (CHORD) telescope, which provides a representative use case for the system's performance evaluation. Each backplane hosts up to four CRS boards, and a single crate integrates four interconnected backplanes to accommodate sixteen CRS modules (for a total of 128 digitized inputs per crate) interconnected through 25 Gbps per-lane links and an on-backplane data shuffle network. Comprehensive validation demonstrates robust high-speed link performance, sub-sampling-level timing alignment stability, and stable thermal and power behavior across environmental variations. The architecture delivers observatory-scale scalability, providing a low-jitter and phase-consistent foundation for wideband digital correlators. By supporting expansion from single-crate to multi-crate configurations without firmware modification, the system offers a practical and flexible path toward next-generation interferometers requiring tightly synchronized, high-throughput digital backends.

astro-ph.IM↗

arXiv2025

Readout noise of digital frequency multiplexed TES detectors for CUPID

Superconducting transition-edge sensor (TES) detectors have been the standard in Cosmic Microwave Background experiments for almost two decades and are now being adapted for use in nuclear physics, such as neutrinoless double beta decay searches. In this paper we focus on a new high-bandwidth frequency multiplexed TES readout system developed for CUPID, a neutrinoless double beta decay experiment that will replace CUORE. In order to achieve the high energy resolution requirements for CUPID, the readout noise of the system must be kept to a minimum. Low TES operating resistance and long wiring between the readout SQUID and the warm electronics are needed for CUPID, prompting a careful consideration of the design parameters of this application of frequency multiplexing. In this work, we characterize the readout noise of the newly designed frequency multiplexed TES readout system for CUPID and construct a noise model to understand it. We find that current sharing between the SQUID coil impedance and other branches of the circuit, as well as the long output wiring, worsen the readout noise of the system. To meet noise requirements, a SQUID with a low input inductance, high transimpedance and/or low dynamic impedance is needed, and the wiring capacitance should be kept as small as possible. Alternatively, the option of adding a cryogenic low-noise amplifier at the output of the SQUID should be explored.

physics.ins-det↗

arXiv2025

In-situ control of the resonant frequency of kinetic inductance detectors with multiplexed readout

Large multiplexing factors are a primary advantage of kinetic inductance detectors (KIDs), but the implementation of high density arrays still presents significant challenges. Deviations between designed and achieved resonant frequencies are common, and differential loading and responsivity variation across an array may lead to dynamic inter-resonator interactions. It is therefore valuable to be able to both set and maintain the resonant frequency of a KID in situ, using the readout system. We show that it is possible to alter the resonant frequency of the devices by multiple linewidths through the application of readout current, and establish a new stable operational bias point at the driven frequency by making use of the hysteretic bistability commonly seen as bifurcation in frequency-domain measurements. We examine this interaction using a readout tone at fixed frequency positioned near or within the unbiased resonant bandwidth. Development of a control methodology based on this principle remains in an early stage, but a foundational step is understanding the interaction of the readout current with the resonator, in particular its influence on the resonant frequency. In this work, we study conventional KIDs with no physical isolation from the substrate, so we posit that the readout current primarily interacts with the resonator via non-thermal mechanisms, resulting in a predominantly reactive response. This behaviour is reproduced by a simple lumped-element circuit model of the resonance and readout system, providing a straightforward framework for analysis and interpretation. This demonstration is an important early step in the development of techniques which seek to dynamically alter the resonant frequencies of conventional KID arrays, and sets the stage for fast active resonant frequency control under operational conditions.

physics.ins-det↗

arXiv2024

A first demonstration of active feedback control and multi-frequency imaging techniques for kinetic inductance detectors

RF-ICE is a signal processing platform for the readout of large arrays of superconducting resonators. Designed for flexibility, the system's low digital latency and ability to independently and dynamically set the frequency and amplitude of probe tones in real time has enabled previously-inaccessible views of resonator behaviour, and opened the door to novel resonator control schemes. We introduce a multi-frequency imaging technique, developed with RF-ICE, which allows simultaneous observation of the entire resonance bandwidth. We demonstrate the use of this technique in the examination of the response of superconducting resonators to variations in applied readout current and thermal loading. We observe that, used in conjunction with a conventional frequency sweep at sufficiently large amplitude to induce resonance bifurcation, the multi-frequency imaging technique reveals a resonator response which is not captured by the frequency sweep measurement alone. We demonstrate that equivalent resonant frequency shifts can be achieved using either thermal, optical, or readout loading, and use this equivalence to counteract a change in thermal loading by digitally modulating the readout current through a resonator. We develop and implement a proof-of-concept closed-loop negative electro-quasiparticle feedback algorithm which first sets and then maintains the resonant frequency of a lumped element kinetic inductance detector while the loading on it is varied. Although this simple implementation is not yet suitable to deploy at scale, it demonstrates the utility of this feedback technique to improve linearity while addressing amplifier distortion, resonator response non-uniformity, and crosstalk. It can be applied to kinetic inductors in non-bolometric operation, and sets the stage for future developments.

astro-ph.IM↗

arXiv2024

The CRS: a scalable full-stack control system for Microwave Kinetic Inductance Detectors

The t0.technology Control and Readout System (CRS) is a modular microwave control and readout system for mm-wave and radio astronomy, THz imaging, noise radar, and superconducting qubit control. The configuration discussed in this work implements firmware for readout of microwave Kinetic Inductance Detector (KID) arrays. The CRS can operate 4,096 KIDs over 2.5 GHz of complex bandwidth between 0-10 GHz, typically allocated across four independent RF chains at 1,024x multiplexing and 625 MHz of complex bandwidth each. Every CRS can operate as a standalone unit or collectively within one or more backplane-enabled subracks that distribute power, clocking, and synchronization, scaling to an arbitrary number of channels. Each fully populated subrack supports arrays of more than 65,000 KIDs. The signal processing and control software supports recent innovations in multi-probe measurements and dynamic feedback modes, which are described in (Rouble et al. 2024). The CRS has recently been selected as the new baseline readout system for the proposed South Pole Telescope instrument, SPT-3G+. We present the hardware design, firmware capabilities, open-source control and data acquisition software, and the first laboratory characterization measurements.

astro-ph.IM↗

arXiv2022

Design of the on-board data compression for the bolometer data of LiteBIRD

LiteBIRD is a space-borne experiment dedicated to detecting large-scale $B$-mode anisotropies in the linear polarization of the Cosmic Microwave Background (CMB) predicted by the theory of inflation. It is planned to be launched in the late 2020s to the second Lagrange point (L2) of the Sun-Earth system. LiteBIRD will map the sky in 15 frequency bands. In comparison to $\it{Planck}$ HFI, the previous low-temperature bolometer-based satellite for CMB observations, the number of detector has increased by two orders of magnitude, up to $\sim$5000 detectors in total. The data rate is 19 Hz from each detector. The bandpass to the ground is limited to 10 Mbps using the X-band for a few hours per day. These require the data to be compressed by more than 50 %. The exact value depends on how much information entropy is contained in the real data. We have thus evaluated the compression by simulating the time-ordered data of polarization sensitive bolometers. The foreground emission, detector noise, cosmic ray glitches, leakage from the CMB intensity to polarization, etc. are simulated. We investigated several algorithms and demonstrated that the required compression ratio can be achieved by some of them. We describe the details of this evaluation and propose algorithms that can be employed in the on-board digital electronics of LiteBIRD.

astro-ph.IM↗

arXiv2022

Development of TRL5 Space Qualified Hardware for Tuning, Biasing, and Readout of Kilopixel TES Bolometer Arrays

The next generation of space-based mm-wave telescopes, such as JAXA's LiteBIRD mission, require focal planes with thousands of detectors in order to achieve their science goals. Digital frequency-domain multiplexing (dfmux) techniques allow detector counts to scale without a linear growth in wire harnessing, sub-Kelvin refrigerator loads, and other scaling problems. In this paper, we introduce Technology Readiness Level 5 (TRL5) electronics suitable for biasing and readout of LiteBIRD's Transition Edge Sensor (TES) bolometers using dfmux techniques. These electronics sit between the spacecraft's payload computer and the cryogenic focal plane, and provide detector biasing, tuning, and readout interfaces between these detectors and the spacecraft's on-board storage. We describe the overall architecture of the electronics, including functional decomposition into modules, the numerology and interconnection of these modules, and their internal and external interfaces. We describe performance measurements to date, including power consumption, thermal performance, and mass, volume, and reliability estimates. This paper is a companion piece to a description of the electronics' on-board Field-Programmable Gate Array (FPGA) firmware.

astro-ph.IM↗

arXiv2022

Development of TRL5 Firmware for Tuning, Biasing, and Readout of Kilopixel TES Bolometer Arrays

The next generation of space-based mm-wave telescopes, such as JAXA's LiteBIRD mission, require focal planes with thousands of detectors in order to achieve their science goals. Digital frequency-domain multiplexing (dfmux) techniques allow detector counts to scale without a linear growth in wire harnessing, sub-Kelvin refrigerator loads, and other scaling problems. In this paper, we describe the Digital Signal Processing (DSP) firmware executed in the design's FPGA. This firmware is responsible for synthesizing bias tones, performing dynamic feedback control of the bolometer voltage bias and/or Superconducting Quantum Interference Device (SQUID) nuller currents, demodulating and decimating bolometer channels into science data, and streaming the results for storage and eventual downlink. We describe how this firmware has been tailored for LiteBIRD, including the control path, improvements to power- and resource-efficiency, the addition of radiation-mitigation functions, and the integration of new bolometer biasing schemes that may help mitigate mission-specific design challenges. This paper is a companion piece to the description of the electronics platform in which the firmware operates.

astro-ph.IM↗

arXiv2022

Digital Active Nulling for Frequency-Multiplexed Bolometer Readout: Performance and Latency

We consider the stability and performance of a discrete-time control loop used as a dynamic nuller in the presence of a relatively large time delay in its feedback path. Controllers of this form occur in mm-wave telescopes using frequency-multiplexed Transition Edge Sensor (TES) bolometers. In this application, negative feedback is needed to linearize a Superconducting Quantum Interference Device (SQUID) used as an amplifier. $M$ such feedback loops are frequency-multiplexed through a SQUID at distinct narrowband frequencies in the MHz region. Loop latencies stem from the use of polyphase filter bank (PFB) up- and down-converters and have grown significantly as the detector count in these experiments increases. As expected, latency places constraints on the overall gain $K$ for which the loop is stable. However, latency also creates spectral peaks at stable gains in the spectral response of the closed loop. Near these peaks, the feedback loop amplifies (rather than suppresses) input signals at its summing junction, rendering it unsuitable for nulling over a range of stable gains. We establish a critical gain $K_C$ above which this amplifying or "anti-nulling" behaviour emerges, and find that $K_C$ is approximately a factor of 3.8 below the gain at which the system becomes unstable. Finally, we describe an alteration to the loop tuning algorithm that selects an appropriate (stable, effective for nulling) loop gain without sensitivity to variations in analog gains due to component tolerances.

astro-ph.IM↗

arXiv2018

The EBEX Balloon Borne Experiment - Detectors and Readout

EBEX was a long-duration balloon-borne experiment to measure the polarization of the cosmic microwave background. The experiment had three frequency bands centered at 150, 250, and 410 GHz and was the first to use a kilo-pixel array of transition edge sensor (TES) bolometers aboard a balloon platform; shortly after reaching float we operated 504, 342, and 109 TESs at each of the bands, respectively. We describe the design and characterization of the array and the readout system. We give the distributions of measured thermal conductances, normal resistances, and transition temperatures. With the exception of the thermal conductance at 150 GHz. We measured median low-loop-gain time constants $τ_{0}=$ 88, 46, and 57 ms and compare them to predictions. Two measurements of bolometer absorption efficiency show high ($\sim$0.9) efficiency at 150 GHz and medium ($\sim$0.35, and $\sim$0.25) at the two higher bands, respectively. We measure a median total optical load of 3.6, 5.3 and 5.0 pW absorbed at the three bands, respectively. EBEX pioneered the use of the digital version of the frequency domain multiplexing (FDM) system which multiplexed the bias and readout of 16 bolometers onto two wires. We present accounting of the measured noise equivalent power. The median per-detector noise equivalent temperatures referred to a black body with a temperature of 2.725 K are 400, 920, and 14500 $μ$K$\sqrt{s}$ for the three bands, respectively. We compare these values to our pre-flight predictions and to a previous balloon payload, discuss the sources of excess noise, and the path for a future payload to make full use of the balloon environment.

astro-ph.IM↗

arXiv2018

Optical Characterization of the SPT-3G Focal Plane

The third-generation South Pole Telescope camera is designed to measure the cosmic microwave background across three frequency bands (95, 150 and 220 GHz) with ~16,000 transition-edge sensor (TES) bolometers. Each multichroic pixel on a detector wafer has a broadband sinuous antenna that couples power to six TESs, one for each of the three observing bands and both polarization directions, via lumped element filters. Ten detector wafers populate the focal plane, which is coupled to the sky via a large-aperture optical system. Here we present the frequency band characterization with Fourier transform spectroscopy, measurements of optical time constants, beam properties, and optical and polarization efficiencies of the focal plane. The detectors have frequency bands consistent with our simulations, and have high average optical efficiency which is 86%, 77% and 66% for the 95, 150 and 220 GHz detectors. The time constants of the detectors are mostly between 0.5 ms and 5 ms. The beam is round with the correct size, and the polarization efficiency is more than 90% for most of the bolometers

astro-ph.IM↗

arXiv2016

ICE-based Custom Full-Mesh Network for the CHIME High Bandwidth Radio Astronomy Correlator

New generation radio interferometers encode signals from thousands of antenna feeds across large bandwidth. Channelizing and correlating this data requires networking capabilities that can handle unprecedented data rates with reasonable cost. The Canadian Hydrogen Intensity Mapping Experiment (CHIME) correlator processes 8-bits from N=2048 digitizer inputs across 400~MHz of bandwidth. Measured in $N^2~\times $ bandwidth, it is the largest radio correlator that has been built. Its digital back-end must exchange and reorganize the 6.6~terabit/s produced by its 128 digitizing and channelizing nodes, and feed it to the 256-node spatial correlator in a way that each node obtains data from all digitizer inputs but across a small fraction of the bandwidth (i.e. `corner-turn'). In order to maximize performance and reliability of the corner-turn system while minimizing cost, a custom networking solution has been implemented. The system makes use of Field Programmable Gate Array (FPGA) transceivers to implement direct, passive, full-mesh, high speed serial connections between sixteen circuit boards in a crate, to exchange data between crates, and to offload the data to a cluster of 256 graphics processing unit (GPU) nodes using standard 10~Gbit/s Ethernet links. The GPU nodes complete the corner-turn by combining data from all crates and then computing visibilities. Eye diagrams and frame error counters confirm error-free operation of the corner-turn network in both the currently operating CHIME Pathfinder telescope (a prototype for the full CHIME telescope) and a representative fraction of the full CHIME hardware providing an end-to-end system validation. An analysis of an equivalent corner-turn system built with Ethernet switches instead of custom passive data links is provided.

astro-ph.IM↗

arXiv2016

Temperature calibration of the E and B experiment

The E and B Experiment (EBEX) is a balloon-borne polarimeter designed to measure the polarization of the cosmic microwave background radiation and to characterize the polarization of galactic dust. EBEX was launched December 29, 2012 and circumnavigated Antarctica observing $\sim$6,000 square degrees of sky during 11 days at three frequency bands centered around 150, 250 and 410 GHz. EBEX was the first experiment to operate a kilo-pixel array of transition-edge sensor bolometers and a continuously rotating achromatic half-wave plate aboard a balloon platform. It also pioneered the use of detector readout based on digital frequency domain multiplexing. We describe the temperature calibration of the experiment. The gain response of the experiment is calibrated using a two-step iterative process. We use signals measured on passes across the Galactic plane to convert from readout-system counts to power. The effective smoothing scale of the EBEX optics and the star camera-to-detector offset angles are determined through \c{hi}2 minimization using the compact HII region RCW 38. This two-step process is initially performed with parameters measured before the EBEX 2013 flight and then repeated until the calibration factor and parameters converge.

astro-ph.IM↗

arXiv2016

POLARBEAR Constraints on Cosmic Birefringence and Primordial Magnetic Fields

We constrain anisotropic cosmic birefringence using four-point correlations of even-parity $E$-mode and odd-parity $B$-mode polarization in the cosmic microwave background measurements made by the POLARization of the Background Radiation (POLARBEAR) experiment in its first season of observations. We find that the anisotropic cosmic birefringence signal from any parity-violating processes is consistent with zero. The Faraday rotation from anisotropic cosmic birefringence can be compared with the equivalent quantity generated by primordial magnetic fields if they existed. The POLARBEAR nondetection translates into a 95% confidence level (C.L.) upper limit of 93 nanogauss (nG) on the amplitude of an equivalent primordial magnetic field inclusive of systematic uncertainties. This four-point correlation constraint on Faraday rotation is about 15 times tighter than the upper limit of 1380 nG inferred from constraining the contribution of Faraday rotation to two-point correlations of $B$-modes measured by Planck in 2015. Metric perturbations sourced by primordial magnetic fields would also contribute to the $B$-mode power spectrum. Using the POLARBEAR measurements of the $B$-mode power spectrum (two-point correlation), we set a 95% C.L. upper limit of 3.9 nG on primordial magnetic fields assuming a flat prior on the field amplitude. This limit is comparable to what was found in the Planck 2015 two-point correlation analysis with both temperature and polarization. We perform a set of systematic error tests and find no evidence for contamination. This work marks the first time that anisotropic cosmic birefringence or primordial magnetic fields have been constrained from the ground at subdegree scales.

astro-ph.CO↗

arXiv2014

The performance of the bolometer array and readout system during the 2012/2013 flight of the E and B experiment (EBEX)

EBEX is a balloon-borne telescope designed to measure the polarization of the cosmic microwave background radiation. During its eleven day science flight in the Austral Summer of 2012, it operated 955 spider-web transition edge sensor (TES) bolometers separated into bands at 150, 250 and 410 GHz. This is the first time that an array of TES bolometers has been used on a balloon platform to conduct science observations. Polarization sensitivity was provided by a wire grid and continuously rotating half-wave plate. The balloon implementation of the bolometer array and readout electronics presented unique development requirements. Here we present an outline of the readout system, the remote tuning of the bolometers and Superconducting QUantum Interference Device (SQUID) amplifiers, and preliminary current noise of the bolometer array and readout system.

astro-ph.IM↗

arXiv2014

Canadian Hydrogen Intensity Mapping Experiment (CHIME) Pathfinder

A pathfinder version of CHIME (the Canadian Hydrogen Intensity Mapping Experiment) is currently being commissioned at the Dominion Radio Astrophysical Observatory (DRAO) in Penticton, BC. The instrument is a hybrid cylindrical interferometer designed to measure the large scale neutral hydrogen power spectrum across the redshift range 0.8 to 2.5. The power spectrum will be used to measure the baryon acoustic oscillation (BAO) scale across this poorly probed redshift range where dark energy becomes a significant contributor to the evolution of the Universe. The instrument revives the cylinder design in radio astronomy with a wide field survey as a primary goal. Modern low-noise amplifiers and digital processing remove the necessity for the analog beamforming that characterized previous designs. The Pathfinder consists of two cylinders 37\,m long by 20\,m wide oriented north-south for a total collecting area of 1,500 square meters. The cylinders are stationary with no moving parts, and form a transit instrument with an instantaneous field of view of $\sim$100\,degrees by 1-2\,degrees. Each CHIME Pathfinder cylinder has a feedline with 64 dual polarization feeds placed every $\sim$30\,cm which Nyquist sample the north-south sky over much of the frequency band. The signals from each dual-polarization feed are independently amplified, filtered to 400-800\,MHz, and directly sampled at 800\,MSps using 8 bits. The correlator is an FX design, where the Fourier transform channelization is performed in FPGAs, which are interfaced to a set of GPUs that compute the correlation matrix. The CHIME Pathfinder is a 1/10th scale prototype version of CHIME and is designed to detect the BAO feature and constrain the distance-redshift relation.

astro-ph.IM↗

arXiv2014

Calibrating CHIME, A New Radio Interferometer to Probe Dark Energy

The Canadian Hydrogen Intensity Mapping Experiment (CHIME) is a transit interferometer currently being built at the Dominion Radio Astrophysical Observatory (DRAO) in Penticton, BC, Canada. We will use CHIME to map neutral hydrogen in the frequency range 400 -- 800\,MHz over half of the sky, producing a measurement of baryon acoustic oscillations (BAO) at redshifts between 0.8 -- 2.5 to probe dark energy. We have deployed a pathfinder version of CHIME that will yield constraints on the BAO power spectrum and provide a test-bed for our calibration scheme. I will discuss the CHIME calibration requirements and describe instrumentation we are developing to meet these requirements.

astro-ph.IM↗