arXiv subjects

Guiling Wu

Publications and source records attributed to Guiling Wu.

15 recordsLinked to original sources

arXiv2024

Narrowband parallel coherent LiDAR with frequency interleaving

The high demand for 3D imaging in intelligent robotics is motivating the advances of coherent LiDARs towards high performances with low complexity/cost. However, the current coherent LiDARs suffer from the tight coupling between the high ranging-imaging performance and the high complexity/cost. Herein, we propose a narrowband parallel coherent LiDAR with frequency-interleaving architecture. The LiDAR architecture utilizes narrowband signals for ranging, and interleaves multi-channel sparse and narrowband signals in frequency domain at the receiving end to significantly reduce the required bandwidth and the number of detection branches, facilitating massive parallelization with low system complexity/cost. In experiments, a ranging precision of 0.49 mm that approaches the shot noise limit, and a power sensitivity of -95 dBm (~9 photons) are achieved. Parallel 3D imaging with an equivalent imaging rate of 10 Mpixel/s and a 2 cm ranging precision is also demonstrated using only two 150 MHz receiving branches. With these desirable properties, this new LiDAR opens an avenue for the LiDAR ecosystem.

physics.optics↗

arXiv2022

Free-space point-to-multiplepoint optical frequency transfer with lens assisted integrated beam steering

We report on the realization of high-performance silica integrated two-dimensional lens assisted beam-steering (LABS) arrays along with the first-of-their-kind point-to-multiplepoint optical frequency transfer. {The LABS equips with $N$ antennas} and has the capability to produce arbitrary number of output beams with different output angles with the simple control complexity. We demonstrate that the LABS has 16 scanning angles, which can support {the access capability for the maximum of simultaneous 16 user nodes.} The coaxial configuration for transmitting and receiving the light as a monolithic transceiver allows us to reduce the out-of-loop phase noise significantly. Finally, the LABS-based non-blocking point-to-multiplepoint in-door free-space optical frequency transfer links with 24 m and 50 m free-space links are shown. After being compensated for the free-space link up to 50 m, the fractional frequency instability of $4.5\times10^{-17}$ and $7.7\times10^{-20}$ at the averaging time of 1 s and 20,000 s, respectively, can be achieved. The present work proves the potential application of the 2D LABS in free-space optical time-frequency transfer and provides a guidance for developing a chip-scale optical time-frequency transfer system.

physics.ins-det↗

arXiv2022

Multiple-access relay stations for long-haul fiber-optic radio frequency transfer

We report on the realization of a long-haul radio frequency (RF) transfer scheme by using multiple-access relay stations (MARSs). The proposed scheme with independent link noise compensation for each fiber sub-link effectively solves the limitation of compensation bandwidth for long-haul transfer. The MARS can have the capability to share the same modulated optical signal for the front and rear fiber sub-links, simplifying the configuration at the repeater station and enabling the transfer system to have the multiple-access capability. At the same time, we for the first time theoretically model the effect of the MARS position on the fractional frequency instability of the fiber-optic RF transfer, demonstrating that the MARS position has little effect on system's performance when the ratio of the front and rear fiber sub-links is around $1:1$. We experimentally demonstrate a 1 GHz signal transfer by using one MARS connecting 260 and 280 km fiber links with the fractional frequency instabilities of less than $5.9\times10^{-14}$ at 1 s and $8.5\times10^{-17}$ at 10,000 s at the remote site and of $5.6\times10^{-14}$ and $6.6\times10^{-17}$ at the integration times of 1 s and 10,000 s at the MARS. The proposed scalable technique can arbitrarily add the same MARSs in the fiber link, which has great potential in realizing ultra-long-haul RF transfer.

eess.SP↗

arXiv2022

Enhanced phase noise reduction in localized two-way optical frequency comparison

High-stability optical frequency comparison over fiber link enables the establishment of ultrastable optical clock networks, having the potential to promote a series of applications, including metrology, geodesy, and astronomy. In this article, we theoretically analyze and experimentally demonstrate a timedelayed local two-way (TD-LTW) optical frequency comparison scheme with improved comparison stability, showing that the fractional instability of optical frequency comparison over a 50- km transfer link can be reduced from $1.30\times10^{-15}$ to $5.25\times10^{-16}$ at the 1 s integration time with an improvement factor of 2.48. Additionally, we also for the first time model and experimentally verify the effect of the inhomogeneous phase noise along the fiber link on the system performance. We believe that the theory and technique proposed here will be helpful in developing the high-stability optical clock networks over large-area fiber links.

physics.optics↗

arXiv2021

Fiber radio frequency transfer using bidirectional frequency division multiplexing dissemination

We report on the realization of a novel fiber-optic radio frequency (RF) transfer scheme with the bidirectional frequency division multiplexing (FDM) dissemination technique. Here, the proper bidirectional frequency map used in the forward and backward directions for suppressing the backscattering noise and ensuring the symmetry of the bidirectional transfer RF signals within one telecommunication channel. We experimentally demonstrated a 0.9 GHz signal transfer over a 120 km optical link with the relative frequency stabilities of 2.2E-14 at 1 s and 4.6E-17 at 20,000 s. The implementation of phase noise compensation at the remote site has the capability to perform RF transfer over a branching fiber network with the proposed technique as needed by large-scale scientific experiments.

physics.ins-det↗

arXiv2021

Branching optical frequency transfer with enhanced post automatic phase noise cancellation

We present a technique for coherence transfer of laser light through a branching fiber link, where the optical phase noise induced by environmental perturbations via the fiber link is passively compensated by remote users without the requirements of any active servo components. At each remote site, an acousto-optic modulator (AOM) is simultaneously taken as a frequency distinguisher for distinguishing its unique frequency from other sites' and as an optical actuator for compensating the phase noise coming from the optical fiber. With this configuration, we incorporate a long outside loop path consisting of a fiber-pigtailed AOM into the loop, enabling the significant reduction of the outside loop phase noise in the passive way. To further address the residual out-of-loop phase noise coming from the interferometer and the two-way optical frequency comparison setup, we design a low-noise active temperature stabilization system. Measurements with a back-to-back system show that the stability in our stabilization system is $2\times10^{-16}$ at 1 s, reaching $2\times10^{-20}$ after 10,000 s. Adopting these techniques, we demonstrate transfer of a laser light through a branching fiber network with 50 km and 145 km two fiber links. After being compensated for the 145 km fiber link, the relative frequency instability is $3.4\times10^{-15}$ at the 1 s averaging time and scales down to $3.7\times10^{-19}$ at the 10,000 s averaging time. This proposed technique is suitable for the simultaneous transfer of an optical signal to a number of independent users within a local area.

physics.ins-det↗

arXiv2021

Passive Optical Phase Stabilization on a Ring Fiber Network

Optical frequency transfer provides the means for high-fidelity frequency transfer across thousands of kilometers. A critical step in the further developing optical frequency transfer is its capability to transfer a high spectral purity feature from ultrastable lasers or optical clocks to any remote locations and, at the same time, its adaptability to incorporate the optical frequency transfer technique into any existing communication networks with different topologies. Here we for the first time report a technique that delivers optical-frequency signals to multiple independent remote hubs along a ring optical-fiber network with passive phase stabilization. The technique automatically corrects optical-fiber length fluctuations of arbitrary hubs along the loop by mixing and shifting optical signals. Without the help of an active phase tracker and a compensator, it could significantly mitigate some technical problems such as the limited compensation speed and phase recovery time, the phase jitter contamination caused by the servo bump in conventional phase noise cancellation. Moreover, by transmitting optical signals along both directions using the same optical source, it can improve the signal-to-noise ratio at each hub. This technique maintains the same delay-limited phase noise correction capability as in conventional techniques and, furthermore, improves the phase jitter by a factor of 3, opening a way to a broad distribution of an ultrastable frequency reference with high spectral purity and enabling a wide range of applications beyond metrology over a ring fiber network with the naturally impressive reliability and scalability.

physics.ins-det↗

arXiv2021

All-passive multiple-place optical phase noise cancellation

We report on the realization of delivering coherent optical frequency to multiple places based on passive phase noise cancellation over a bus topology fiber network. This technique mitigates any active servo controller on the main fiber link and at arbitrary access places as opposed to the conventional technique, in which an active phase compensation circuit has to be adopted to stabilize the main fiber link. Although the residual fiber phase noise power spectral density (PSD) in the proposed technique turns out to be a factor of 7 higher than that of in the conventional multiple-access technique when the access place is close to the end of the fiber link, it could largely suppress the phase noise introduced by the servo bumps, improve the response speed and phase recovery time, and minimize hardware overhead in systems with many stations and connections without the need of the active servo circuits including phase discriminators and active compensators. The proposed technique could considerably simplify future efforts to make precise optical frequency signals available to many users, as required by some large-scale science experiments.

physics.ins-det↗

arXiv2020

Fundamental Limitations of Rayleigh Backscattering Noise on Fiber-Based Multiple-Access Optical Frequency Transfer

While it has been shown that backscattering induced phase noise can be suppressed by adopting acoustic-optic-modulators (AOMs) at the local and remote sites to break the frequency symmetry in both directions. However, this issue can not be avoided for conventional fiber-optic multiple-access coherent optical phase dissemination in which the interference of the signal light with the Rayleigh backscattered light will probably destroy the coherence of the stabilized optical signal. We suppress the backscattering effect by locally breaking the frequency symmetry at the extraction point by inserting an additional AOM. Here, we theoretically analyze and experimentally demonstrate an add-drop one more AOM approach for suppressing the Rayleigh backscattering within the fiber link. Near-complete suppression of backscattering noise is experimentally confirmed through the measurement the elimination of a common interference term of the signal light and the Rayleigh backscattered light. The results demonstrate that the Rayleigh backscattering light has a limited effect compared to the residual delay-limited fiber phase noise on the system's performance. Our results also provide new evidence that it is possible to largely suppress Rayleigh and other backscattering noise within a long optical fiber link, where the accumulated phase noise could be large, by using frequency symmetry breaking at each access node to achieve robust multiple-access coherent optical phase propagation in spite of scatters or defects.

physics.ins-det↗

arXiv2020

Passive Optical Phase Noise Cancellation

We report on the realization of an optical phase noise cancellation technique by passively embedding the optical phase information into a radio frequency (RF) signal and shifting the optical frequency with the amount of phase noise introduced by optical phase perturbations. Neither phase discrimination nor active phase tracking is required due to the open-loop design, mitigating some technical problems, such as the limited compensation speed and the finite phase/timing jitter, in conventional phase noise cancellation. We experimentally demonstrate that this technique maintains the same delay-limited bandwidth and phase noise suppression capability as in conventional techniques, but significantly shortens the response speed and phase recovery time. Passive decoupling optical phase perturbation represents a powerful technique in the domains of optical frequency standard comparisons and clockworks for future optical atomic clocks, which are now under serious investigation for a potential redefinition of the International Time Scale.

physics.ins-det↗

arXiv2020

Vector network analysis based on wideband direct photonic digitizing

Vector network analyzers (VNAs) have become one of the indispensable tools in various fields, such as medicine, material, geology, communication, and etc, due to the capacity of measuring and analyzing the response of the object under test. Conventional VNAs, commonly based on mixing architecture, have to make compromises among accuracy, dynamic range, and bandwidth. In this paper, we propose a wideband photonic vector network analyzer (PVNA) based on wideband direct photonic digitizing. Ultrastable optical trains directly undersample the response signals from objects under test, followed by electrooptic conversion and quantization, obviating the intricate downconversion procedures in traditional VNAs. Adopting existing commercial devices, the proposed PVNA can not only extend the measurement frequency range to 110 GHz or higher but also achieve a high linearity and accuracy performance. To validate the theoretical analysis, we establish an experimental PVNA, realizing a measurable frequency span of up to 40 GHz and a dynamic range of more than 120 dB. A measured scattering parameters of a bandpass filter The experimental result is well consistent with that of a commercial network analyzer.

eess.SP↗

arXiv2020

Multi-node optical frequency dissemination with post automatic phase correction

We report a technique for coherence transfer of laser light through a fiber link, where the optical phase noise induced by environmental perturbation via the fiber link is compensated by remote users with passive phase noise correction, rather than at the input as is conventional. Neither phase discrimination nor active phase tracking is required due to the open-loop design, mitigating some technical problems such as the limited compensation speed and the finite compensation precision as conventional active phase noise cancellation. We theoretically analyze and experimentally demonstrate that the delay effect introduced residual fiber phase noise after noise compensation is a factor of 7 higher than the conventional techniques. Using this technique, we demonstrate the transfer laser light through a 145-km-long, lab-based spooled fiber. After being compensated, the relative frequency instability in terms of overlapping Allan deviation is 1.9E-15 at 1s averaging time and scales down 5.3E-19 at 10,000 s averaging time. The frequency uncertainty of the light after transferring through the fiber relative to that of the input light is -0.36+-2.6E-18. As the transmitted optical signal remains unaltered until it reaches the remote sites, it can be transmitted simultaneously to multiple remote sites on an arbitrarily complex fiber network, paving a way to develop a multi-node optical frequency dissemination system with post automatic phase noise correction for a number of end users.

physics.optics↗

arXiv2017

Experimental Demonstration of High-Precision Multi-access Time Transfer via Optical-Electrical-Optical Repeater Stations

In this paper, we propose a kind of optical-electrical-optical (OEO) repeater station for the time transfer based on bidirectional time division multiplexing transmission over a single fiber with the same wavelength (BTDM-SFSW). Along the main fiber link, the forward and backward time signals alternatively pass through the same OEO repeater via a 2X2 optical switch (OS). By this means, the optical powers of bidirectional time signals increase. And parts of excess noises, suffered from the main link, are sufficiently blocked owing to the OEO process. Simultaneously, the bidirectional time signals can be decoded and utilized for multi-access time transfer. As a result of the same devices for both directions, the maximum delay symmetry is maintained, and the performance for multi-access time transfer is guaranteed. With the OEO repeater stations, we successfully demonstrate multi-access time transfer in our time transfer testbeds with the main links up to 13,200 km. The time deviations of less than 80 ps/s and 11 ps/10^5 s, respectively, are obtained. Furthermore, the combined standard uncertainties of less than 70 ps are reached, which agree well with the experimental verifications over non-calibrated fiber links.

physics.optics↗

arXiv2017

High-precision Joint Time and Frequency Transfer over a Fiber-optic Telecom Testbed

It is highly desired to operate a joint time and frequency transfer over the exiting fiber-optic telecom networks with the commercial data transmission. Previously, we proposed a time transfer scheme based on bidirectional time division multiplexing transmission over a single fiber with the same wavelength (BTDM-SFSW), and an optical amplification scheme of single-fiber bidirectional-transmission unidirectional optical amplifier (SFBT-UOA). The effects of excess noises like Rayleigh backscattering etc. on the received time signals can be efficiently suppressed for an accepted timing jitter. Simultaneously, the bidirectional propagation delay symmetry can be guaranteed for an expected uncertainty without requiring complicated and expensive link calibration. In this paper, we propose a high-precision joint BTDM-SFSW based time and unidirectional frequency transfer over conventional telecom networks. A stable frequency signal is achieved by compensating the fiber temperature dependent phase variation according to the time transfer. The proposed joint transfer scheme is demonstrated over a 320 km fiber-optic telecom testbed with two 10 Gb/s data transmission channels. The time transfer stabilities (time deviation, TDEV) of 23.2 ps/s and 5.4 ps/10^5 s, respectively, and the frequency transfer stabilities (Allan deviation, ADEV) of 5.4X10^(-13)/s and 9.5X10^(-17)/10^5 s, respectively, are reached. The measured bit error rates (BER) of the 10 Gb/s communication data are well below 10^(-13).

physics.ins-det↗

arXiv2016

Basic Theoretical Model and Sampling Criteria for Time-Interleaved Photonic Analog-to-Digital Converters

In this paper, we present a basic model for time-interleaved photonic analog-to-digital converter (TIPADC) and analyze its linear, nonlinear, and noise performance. The basic operation mechanism of TIPADC is illustrated and the linear performance is analyzed in frequency domain. The mathematical expressions and the output of the system are presented in each processing step. We reveal that photonic sampling folds the whole spectrum of input signal in a narrow band, which enables the analog bandwidth of a TIPADC to be much higher than the bandwidth of back-end electronics. The feasible regions of the system is obtained in terms of system frequency response, and a set of sampling criteria determining the basic requirements to the system are summarized for typical applications. The results show that the global minimum feasible bandwidth of back-end electronics is the half of single channel sampling rate when the bandwidth of photonic sampling pulse is comparable to input signal frequency. The amplitude and phase noise of photonic sampling pulse train, the thermal noise and shot noise of photodetection, and the quantization noise and aperture jitter noise of EADCs are investigated. The nonlinearity of TIPADC is also analyzed. The effect of different factors, such as the single channel sampling rate, the average optical power and the bandwidth of back-end electronics, on the effective number of bits of TIPADC is qualitatively and quantitatively discussed. The results explicitly show that TIPADC can perform high fidelity conversion to ultra-high speed analog signal and overcome the major performance limitations existing in traditional ADCs such as aperture jitter and bandwidth. The criteria deduced will be an effective supplement to the generalized sampling theorem in designing TIPADC.

physics.ins-det↗