arXiv subjects

Guy Perrin

Publications and source records attributed to Guy Perrin.

At least 19 recordsLinked to original sources

arXiv2026

GRAVITY+: reducing non-common-path aberrations for sub-10 {\mu}as astrometric accuracy

GRAVITY is a state-of-the-art instrument for near-infrared astrometric interferometry that routinely achieves astrometric accuracy of 30-100 microarcsecond in its phase-referenced dual-field mode. However, its fundamental limit is not yet reached, and can still be improved by several factors. In this paper, we focus on the effect of systematics, and in particular the effect of non-common path aberrations between the science channel and the metrology signal in the GRAVITY Fiber Coupler. Through comprehensive laboratory measurements using a dedicated fiber coupler replica and phase-shifting interferometry at 1908 nm, we have characterized these high-order wavefront errors with nanometer precision in the laboratory. We characterized on-sky the effect of these high-order wavefront imperfections on narrow-angle astrometry, using observations of the binary system GJ65. As part of the GRAVITY+ project, high-precision mirrors designed for nanometer-level surface quality, bringing an order of magnitude improvement over existing GRAVITY injection optics, are currently in production and will be installed in the fiber coupler units by the end of 2027. This upgrade is expected to enable astrometric accuracy at the sub-10 microarcsecond level in dual-field mode with integration times of just a few minutes.

astro-ph.IM↗

arXiv2026

FIRST-PL: Commissioning the first visible photonic lantern spectrograph for sub-diffraction-limit astronomy on Subaru/SCExAO

FIRST-PL (Fibered Imager foR a Single Telescope - Photonic Lantern) is a newly commissioned visible-light instrument on Subaru/SCExAO achieving spectroscopy below the diffraction limit. The instrument uses a Photonic Lantern (PL)-converting multimode fiber into 19 single-mode outputs-feeding a mid-resolution spectrograph (R 3000, 630-790 nm). On-sky performance demonstrates 40% injection efficiency at 680 nm (Strehl 30%) and 12x throughput improvement over single-mode fibers. Three operational modes enable spectro-astrometry (50 microarcseconds precision demonstrated on beta-CMi), image reconstruction, and high-contrast imaging. FIRST-PL represents a significant advancement in high-throughput photonic instrumentation.

astro-ph.IM↗

arXiv2026

Effects of a disk structure on stellar motion at the Galactic Center

Stellar orbits are key for probing the environment of the supermassive black hole at the Galactic Center, Sagittarius A$^*$. So far, the mass around SgrA$^*$ has been assumed to be spherically distributed. However, the extended mass may instead be flattened, creating disk-like structures. We investigate the effects that a thin disk structure would have on stars at the Galactic Center, focusing on star S2 and S301 and the clockwise stellar disk. We derive analytically the acceleration exerted by a disk with power law density $\Sigma \propto r^{-\gamma}$. We use this acceleration to compute the osculating equations and the variations of the orbital elements, showing how the latter depend on the orientation of the disk with respect to the orbital plane. We find that the disk structure induces a secular shift in the semi-latus rectum, an extra in-plane precession and an out-of-plane precession. The former is neither present at the low-order post Newtonian description that we use for the black hole, nor when a spherical mass distribution is considered. The latter can be competitive with the Lense-Thirring precession induced by the spin of SgrA$^*$ on S301 motion, depending on the mass, the radial extent and the orientation of the disk. Since the Lense-Thirring precession is negligible in S2 motion, the out-of-plane precession can be used to place upper limits on the non luminous mass of disk-like structures at the Galactic Center. The limits might significantly differ from those obtained for spherical distributions and depend on the disk parameters. These results highlight the importance of constraining disk-like structures when using stellar orbits to probe the central black hole, in particular its spin. Once mass estimates are at hand, one can quantify the disk's effect on S301 motion and the resulting degeneracy with a future measurement of SgrA$^*$ spin.

astro-ph.GA↗

arXiv2026

Using VLTI/GRAVITY+ to determine the identity of a third planet candidate in the PDS 70 system

Detections of protoplanets are rare and protoplanetary disk features mischaracterized as planets are common. PDS 70 is one of only two stars known to host multiple confirmed protoplanets, PDS 70 b and c, and repeat detections of a third point-like source in the system suggest the presence of third inner planet. However, previous observations of this third source are insufficient to distinguish whether it is a planet or a concentrated dust clump in Keplerian motion. Our observations with VLTI/GRAVITY+ did not re-detect this point-like source, suggesting that it is, in fact, a dust clump and not a planet. These observations demonstrate how the angular resolving power of VLTI/GRAVITY+ can be used to distinguish between protoplanets and protoplanetary disk features.

astro-ph.EP↗

arXiv2026

Theory of optical long-baseline interferometry on polarized sources

The effects of the polarization characteristics of beam trains in optical long-baseline interferometers are well known and have led to difficulties in measuring the spatial coherence of astronomical sources in the past. This has been overcome by designing symmetrical optical trains. With the advent of interferometers using large telescopes, observations of faint sources with high degrees of polarization have become even more possible. As in the radio domain, where radiation processes usually lead to high polarization rates, a description of coherence for polarized or unpolarized sources observed with non-polarization neutral interferometers is necessary. A theory of optical long-baseline interferometry fully taking into account the polarization characteristics of beam trains and those of the sources is presented in this paper, building on concepts developed for radio aperture synthesis. The concept of generalized Mueller matrix is introduced for the case of multi-aperture interferometers leading to a simple matrix relationship between the observed Stokes visibilities, as they are disturbed by the instrument polarization characteristics, and the object Stokes visibilities. This relationship is applied to the case of single-mode interferometers. The formalism also shows that classical complex visibilities (squared moduli, phases and closure phases) need to be debiased from polarization crosstalk, even when the source is not polarized as in this case ghost polarized visibilities are created.

astro-ph.IM↗

arXiv2025

Biases induced by retardance and diattenuation in the measurements of long-baseline interferometers

I derive in this paper theoretical expressions for biases on fringe contrast and fringe visibility phase for optical interferometers whose polarizing properties can be described by beam rotation, retardance, and diattenuation. The nature of these biases is discussed for natural light, circular and linear polarization, and partially polarized light. Expansions are obtained for small degrees of polarization, small differential retardance, and small diattenuation. The biases on fringe contrasts are already known. It is shown in this paper that retardance and diattenuation are also sources of bias on the visibility phases and derived quantities. In some cases, the bias is zero. If the retardance is achromatic, differential phases are not affected. Closure phases are not affected to the second order for an interferometer with weak diattenuation and weak differential retardance and for moderately polarized sources whatever the type of light. Otherwise, a calibration procedure is required. It is shown that astrometric measurements are biased in the general case. The bias depends on both the polarization properties of the interferometer and on the (u,v) sampling. In the extreme case where the samples are aligned on a line crossing the origin of the spatial frequency plane, the bias is undetermined and can be arbitrarily large. In all other cases, it can be calibrated if the polarizing characteristics of the interferometer are known. In the case of low differential retardance and low degree of polarization, the bias lies on a straight line, crossing the astrometric reference point. If the degree of linear polarization varies during the observations, then the astrometric bias has a remarkable signature, which describes a section of the line. For slightly polarizing interferometers, a fixed offset is added without changing the shape of the bias.

astro-ph.IM↗

arXiv2024

First Resolution of Microlensed Images of a Binary-Lens Event

We resolve the multiple images of the binary-lens microlensing event ASASSN-22av using the GRAVITY instrument of the Very Large Telescope Interferometer (VLTI). The light curves show weak binary-lens perturbations, complicating the analysis, but the joint modeling with the VLTI data breaks several degeneracies, arriving at a strongly favored solution. Thanks to precise measurements of angular Einstein radius \theta_E = 0.724 +/- 0.002 mas and microlens parallax, we determine that the lens system consists of two M dwarfs with masses of M_1 = 0.258 +/- 0.008 M_sun and M_2 = 0.130 +/- 0.007 M_sun, a projected separation of r_\perp = 6.83 +/- 0.31 au and a distance of D_L = 2.29 +/- 0.08 kpc. The successful VLTI observations of ASASSN-22av open up a new path for studying intermediate-separation (i.e., a few astronomical units) stellar-mass binaries, including those containing dark compact objects such as neutron stars and stellar-mass black holes.

astro-ph.SR↗

arXiv2024

Improving constraints on the extended mass distribution in the Galactic Center with stellar orbits

Studying the orbital motion of stars around Sagittarius A* in the Galactic Center provides a unique opportunity to probe the gravitational potential near the supermassive black hole at the heart of our Galaxy. Interferometric data obtained with the GRAVITY instrument at the Very Large Telescope Interferometer (VLTI) since 2016 has allowed us to achieve unprecedented precision in tracking the orbits of these stars. GRAVITY data have been key to detecting the in-plane, prograde Schwarzschild precession of the orbit of the star S2, as predicted by General Relativity. By combining astrometric and spectroscopic data from multiple stars, including S2, S29, S38, and S55 - for which we have data around their time of pericenter passage with GRAVITY - we can now strengthen the significance of this detection to an approximately $10 \sigma$ confidence level. The prograde precession of S2's orbit provides valuable insights into the potential presence of an extended mass distribution surrounding Sagittarius A*, which could consist of a dynamically relaxed stellar cusp comprised of old stars and stellar remnants, along with a possible dark matter spike. Our analysis, based on two plausible density profiles - a power-law and a Plummer profile - constrains the enclosed mass within the orbit of S2 to be consistent with zero, establishing an upper limit of approximately $1200 \, M_\odot$ with a $1 \sigma$ confidence level. This significantly improves our constraints on the mass distribution in the Galactic Center. Our upper limit is very close to the expected value from numerical simulations for a stellar cusp in the Galactic Center, leaving little room for a significant enhancement of dark matter density near Sagittarius A*.

astro-ph.GA↗

arXiv2024

Spectroscopy using a visible photonic lantern at the Subaru telescope: Laboratory characterization and first on-sky demonstration on Ikiiki ({\alpha} Leo) and `Aua ({\alpha} Ori)

Photonic lanterns are waveguide devices enabling high throughput single mode spectroscopy and high angular resolution. We aim to present the first on-sky demonstration of a photonic lantern (PL) operating in visible light, to measure its throughput and assess its potential for high-resolution spectroscopy of compact objects. We used the SCExAO instrument (a double stage extreme AO system installed at the Subaru telescope) and FIRST mid-resolution spectrograph (R 3000) to test the visible capabilities of the PL on internal source and on-sky observations. The best averaged coupling efficiency over the PL field of view was measured at 51% +/- 10% with a peak at 80%. We also investigate the relationship between coupling efficiency and the Strehl ratio for a PL, comparing them with those of a single-mode fiber (SMF). Findings show that in the AO regime, a PL offers better coupling efficiency performance than a SMF, especially in the presence of low spatial frequency aberrations. We observed Ikiiki (alpha Leo - mR = 1.37) and `Aua (alpha Ori - mR = -1.17) at a frame rate of 200 Hz. Under median seeing conditions (about 1 arcsec measured in H band) and large tip/tilt residuals (over 20 mas), we estimated an average light coupling efficiency of 14.5% +/- 7.4%, with a maximum of 42.8% at 680 nm. We were able to reconstruct both star's spectra, containing various absorption lines. The successful demonstration of this device opens new possibilities in terms of high throughput single-mode fiber-fed spectroscopy in the Visible. The demonstrated on-sky coupling efficiency performance would not have been achievable with a single SMF injection setup under similar conditions, partly because the residual tip/tilt alone exceeded the field of view of a visible SMF (18 mas at 700 nm). Thus emphasizing the enhanced resilience of PL technology to such atmospheric disturbances. The additional

astro-ph.IM↗

arXiv2024

Spectral interferometric wavefront sensing: a solution for petalometry at Subaru/SCExAO

The petaling effect, induced by pupil fragmentation from the telescope spider, drastically affects the performance of high contrast instruments by inducing core splitting on the PSF. Differential piston/tip/tilt aberrations within each optically separated fragment of the pupil are poorly measured by commonly used Adaptive Optics (AO) systems. We here pursue a design of dedicated low-order wavefront sensor -- or petalometers -- to complement the main AO. Interferometric devices sense differential aberrations between fragments with optimal sensitivity; their weakness though is their limitation to wrapped phase measurements. We show that by combining multiple spectral channels, we increase the capture range for petaling aberrations beyond several microns, enough to disambiguate one-wave wrapping errors made by the main AO system. We propose here to implement a petalometer from the multi-wavelength imaging mode of the VAMPIRES visible-light instrument, deployed on SCExAO at the Subaru Telescope. The interferometric measurements obtained in four spectral channels through a 7 hole non-redundant mask allow us to effiiently reconstruct diffierential piston between pupil petals.

astro-ph.IM↗

arXiv2024

Photonic beam-combiner for visible interferometry with SCExAO/FIRST: laboratory characterization and design optimization

Integrated optics are used to achieve astronomical interferometry inside robust and compact materials, improving the instrument's stability and sensitivity. In order to perform differential phase measurements at the H$\alpha$ line (656.3 nm) with the 600-800 nm spectro-interferometer FIRST, a photonic integrated circuit (PIC) is being developed in collaboration with TEEM Photonics. This PIC performs the interferometric combination of the beams coming from sub-apertures selected in the telescope pupil, thus implementing the pupil remapping technique to restore the diffraction limit of the telescope. In this work, we report on the latest developments carried out within the FIRST project to produce a high performance visible PIC. The PICs are manufactured by TEEM Photonics, using their technology based on $K_+:Na_+$ ion exchange in glass. The first part of the study consists in the experimental characterization of the fundamental properties of the waveguides, in order to build an accurate model, which is the basis for the design of more complex functions. In the second part, theoretical designs and their optimization for three types of combiner architectures are presented: symmetric directional coupler, asymmetric directional couplers and ABCD cells including achromatic phase shifters.

astro-ph.IM↗

arXiv2024

Photonic chip for visible interferometry: laboratory characterization and comparison with the theoretical model

Integrated optics are used to achieve astronomical interferometry inside robust and compact materials, improving the instruments stability and sensitivity. In order to perform differential phase measurements at the H$\alpha$ line (656.3 nm) with the 600-800 nm spectro-interferometer FIRST, a photonic integrated circuit (PIC) is being developed. This PIC performs the visible combination of the beams coming from the telescope pupil sub-apertures. In this work, TEEM Photonics waveguides fabricated by $K_+:Na_+$ ion exchange in glass are characterized in terms of single-mode range and mode field diameter. The waveguide diffused index profile is modeled on Beamprop software. FIRST beam combiner building blocks are simulated, especially achromatic directional couplers and passive $\pi/2$ phase shifters for a potential ABCD interferometric combination.

astro-ph.IM↗

arXiv2024

Visible Photonic Lantern integration, characterization and on-sky testing on Subaru/SCExAO

A Photonic Lantern (PL) is a novel device that efficiently converts a multi-mode fiber into several single-mode fibers. When coupled with an extreme adaptive optics (ExAO) system and a spectrograph, PLs enable high throughput spectroscopy at high angular resolution. The Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system of the Subaru Telescope recently acquired a PL that converts its multi-mode input into 19 single-mode outputs. The single mode outputs feed a R~4,000 spectrograph optimized for the 600 to 760 nm wavelength range. We present here the integration of the PL on SCExAO, and study the device performance in terms of throughput, field of view, and spectral reconstruction. We also present the first on-sky demonstration of a Visible PL coupled with an ExAO system, showing a significant improvement of x12 in throughput compared to the use of a sole single-mode fiber. This work paves the way towards future high throughput photonics instrumentation at small angular resolution.

astro-ph.IM↗

arXiv2024

An exact solution to the Fourier Transform of band-limited periodic functions with nonequispaced data and application to non-periodic functions

The need to Fourier transform data sets with irregular sampling is shared by various domains of science. This is the case for example in astronomy or sismology. Iterative methods have been developed that allow to reach approximate solutions. Here an exact solution to the problem for band-limited periodic signals is presented. The exact spectrum can be deduced from the spectrum of the non-equispaced data through the inversion of a Toeplitz matrix. The result applies to data of any dimension. This method also provides an excellent approximation for non-periodic band-limit signals. The method allows to reach very high dynamic ranges ($10^{13}$ with double-float precision) which depend on the regularity of the samples.

math.NA↗

arXiv2023

Photonic spectro-interferometry with SCExAO/FIRST at the Subaru Telescope: towards H-alpha imaging of protoplanets

FIRST is a post Extreme Adaptive-Optics (ExAO) spectro-interferometer operating in the Visible (600-800 nm, R~400). Its exquisite angular resolution (a sensitivity analysis of on-sky data shows that bright companions can be detected down to 0.25lambda/D) combined with its sensitivity to pupil phase discontinuities (from a few nm up to dozens of microns) makes FIRST an ideal self-calibrated solution for enabling exoplanet detection and characterization in the future. We present the latest on-sky results along with recent upgrades, including the integration and on-sky test of a new spectrograph (R~3,600) optimized for the detection of H-alpha emission from young exoplanets accreting matter.

astro-ph.IM↗

arXiv2023

Single-aperture spectro-interferometry in the visible at the Subaru telescope with FIRST: First on-sky demonstration on Keho'oea ({\alpha} Lyrae) and Hokulei ({\alpha} Aurigae)

FIRST is a spectro-interferometer combining, in the visible, the techniques of aperture masking and spatial filtering thanks to single-mode fibers. This instrument aims to deliver high contrast capabilities at spatial resolutions that are inaccessible to classical coronagraphic instruments. The technique implemented is called pupil remapping: the telescope is divided into subpupils by a segmented deformable mirror conjugated to a micro-lens array injecting light into single-mode fibers. The fiber outputs are rearranged in a nonredundant configuration, allowing simultaneous measurement of all baseline fringe patterns. The fringes are also spectrally dispersed, increasing the coherence length and providing precious spectral information. The optical setup of the instrument has been adapted to fit onto the SCExAO platform at the Subaru Telescope. We present the first on-sky demonstration of the FIRST instrument at the Subaru telescope. We used eight subapertures, each with a diameter of about 1 m. Closure phase measurements were extracted from the interference pattern to provide spatial information on the target. We tested the instrument on two types of targets : a point source (Keho'oea) and a binary system (Hokulei). An average accuracy of 0.6 degree is achieved on the closure phase measurements of Keho'oea, with a statistical error of about 0.15 degree at best. We estimate that the instrument can be sensitive to structures down to a quarter of the telescope spatial resolution. We measured the relative positions of Hokulei Aa and Ab with an accuracy about 1 mas. FIRST opens new observing capabilities in the visible wavelength range at the Subaru Telescope. With SCExAO being a testing platform for high contrast imaging instrumentation for future 30-meter class telescopes, FIRST is an important stepping stone for future interferometric instrumentation on extremely large telescopes.

astro-ph.IM↗

arXiv2023

The GRAVITY+ Project: Towards All-sky, Faint-Science, High-Contrast Near-Infrared Interferometry at the VLTI

The GRAVITY instrument has been revolutionary for near-infrared interferometry by pushing sensitivity and precision to previously unknown limits. With the upgrade of GRAVITY and the Very Large Telescope Interferometer (VLTI) in GRAVITY+, these limits will be pushed even further, with vastly improved sky coverage, as well as faint-science and high-contrast capabilities. This upgrade includes the implementation of wide-field off-axis fringe-tracking, new adaptive optics systems on all Unit Telescopes, and laser guide stars in an upgraded facility. GRAVITY+ will open up the sky to the measurement of black hole masses across cosmic time in hundreds of active galactic nuclei, use the faint stars in the Galactic centre to probe General Relativity, and enable the characterisation of dozens of young exoplanets to study their formation, bearing the promise of another scientific revolution to come at the VLTI.

astro-ph.IM↗

arXiv2023

General relativistic effects and the near-infrared and X-ray variability of Sgr A* I

The near-infrared (NIR) and X-ray emission of Sagittarius A* shows occasional bright flares that are assumed to originate from the innermost region of the accretion flow. We identified $25$ $4.5 \mu m$ and $24$ X-ray flares in archival data obtained with the \textit{Spitzer} and \textit{Chandra} observatories. With the help of general relativistic ray-tracing code, we modeled trajectories of ``hot spots'' and studied the light curves of the flares for signs of the effects of general relativity. Despite their apparent diversity in shape, all flares share a common, exponential impulse response, a characteristic shape that is the building block of the variability. This shape is symmetric, that is, the rise and fall times are the same. Furthermore, the impulse responses in the NIR and X-ray are identical within uncertainties, with an exponential time constant $\tau\sim 15$ minute. The observed characteristic flare shape is inconsistent with hot-spot orbits viewed edge-on. Individually modeling the light curves of the flares, we derived constraints on the inclination of the orbital plane of the hot spots with respect to the observer ($i \sim 30^{\circ} , < 75^{\circ} $) and on the characteristic timescale of the intrinsic variability (tens of minutes).

astro-ph.HE↗