arXiv subjects

H. W. Lee

Publications and source records attributed to H. W. Lee.

At least 19 recordsLinked to original sources

arXiv2025

Decadal upgrade strategy for KAGRA toward post-O5 gravitational-wave astronomy

The KAGRA Collaboration has investigated a ten-year upgrade strategy for the KAGRA gravitational wave detector, considering a total of 14 upgrade options that vary in mirror mass, quantum noise reduction techniques, and the quality of cryogenic suspensions. We evaluated the scientific potential of these configurations with a focus on key targets such as parameter estimation of compact binary coalescences, binary neutron star post-merger signals, and continuous gravitational waves. Rather than aiming to improve all science cases uniformly, we prioritized those most sensitive to the detector configuration. Technical feasibility was assessed based on required hardware developments, associated R\&D efforts, cost, and risk. Our study finds that a high-frequency upgrade plan that enhances sensitivity over a broad frequency range above ~200 Hz offers the best balance between scientific return and technical feasibility. Such an upgrade would enable sky localization of binary neutron star mergers at 100 Mpc to better than 0.5 deg$^2$ in a LIGO-Virgo-KAGRA network, and improve the measurement precision of tidal deformability parameter by approximately 10% at median, compared to a network without KAGRA.

gr-qc↗

arXiv2025

Identification of Noise-Associated Glitches in KAGRA O3GK with Hveto

Transient noise ("glitches") in gravitational wave detectors can mimic or obscure true signals, significantly reducing detection sensitivity. Identifying and excluding glitch-contaminated data segments is therefore crucial for enhancing the performance of gravitational-wave searches. We perform a noise analysis of the KAGRA data obtained during the O3GK observation. Our analysis is performed with hierarchical veto (Hveto) which identifies noises based on the statistical time correlation between the main channel and the auxiliary channels. A total of 2,531 noises were vetoed by 28 auxiliary channels with the configuration (i.e., signal-to-noise threshold set to 8) that we chose for Hveto. We identify vetoed events as glitches on the spectrogram via visual examination after plotting them with Q-transformation. By referring to the Gravity Spy project, we categorize 2,354 glitches into six types: blip, helix, scratchy, and scattered light, which correspond to those listed in Gravity Spy, and dot and line, which are not found in the Gravity Spy classification and are thus named based on their spectrogram morphology in KAGRA data. The remaining 177 glitches are determined not to belong to any of these six types. We show how the KAGRA glitch types are related to each subsystem of KAGRA. To investigate the possible correlation between the main channel and the round winner - an auxiliary channel statistically associated with the main channel for vetoing purposes - we visually examine the similarity or difference in the glitch pattern on the spectrogram. We compare the qualitative correlation found through visual examination with coherence, which is known to provide quantitative measurement for the correlation between the main channel and each auxiliary channel. Our comprehensive noise analysis will help improve the data quality of KAGRA by applying it to future KAGRA observation data.

gr-qc↗

arXiv2022

Noise subtraction from KAGRA O3GK data using Independent Component Analysis

In April 2020, KAGRA conducted its first science observation in combination with the GEO~600 detector (O3GK) for two weeks. According to the noise budget estimation, suspension control noise in the low frequency band and acoustic noise in the middle frequency band are identified as the dominant contribution. In this study, we show that such noise can be reduced in offline data analysis by utilizing a method called Independent Component Analysis (ICA). Here the ICA model is extended from the one studied in iKAGRA data analysis by incorporating frequency dependence while linearity and stationarity of the couplings are still assumed. By using optimal witness sensors, those two dominant contributions are mitigated in the real observational data. We also analyze the stability of the transfer functions for whole two weeks data in order to investigate how the current subtraction method can be practically used in gravitational wave search.

astro-ph.IM↗

arXiv2022

Performance of the KAGRA detector during the first joint observation with GEO 600 (O3GK)

KAGRA, the kilometer-scale underground gravitational-wave detector, is located at Kamioka, Japan. In April 2020, an astrophysics observation was performed at the KAGRA detector in combination with the GEO 600 detector; this observation operation is called O3GK. The optical configuration in O3GK is based on a power recycled Fabry-Pérot Michelson interferometer; all the mirrors were set at room temperature. The duty factor of the operation was approximately 53%, and the strain sensitivity was $3\times10^{-22}~/\sqrt{\rm{Hz}}$ at 250 Hz. In addition, the binary-neutron-star (BNS) inspiral range was approximately 0.6 Mpc. The contributions of various noise sources to the sensitivity of O3GK were investigated to understand how the observation range could be improved; this study is called a "noise budget". According to our noise budget, the measured sensitivity could be approximated by adding up the effect of each noise. The sensitivity was dominated by noise from the sensors used for local controls of the vibration isolation systems, acoustic noise, shot noise, and laser frequency noise. Further, other noise sources that did not limit the sensitivity were investigated. This paper provides a detailed account of the KAGRA detector in O3GK including interferometer configuration, status, and noise budget. In addition, strategies for future sensitivity improvements such as hardware upgrades, are discussed.

astro-ph.IM↗

arXiv2021

Overview of KAGRA: Calibration, detector characterization, physical environmental monitors, and the geophysics interferometer

KAGRA is a newly built gravitational wave observatory, a laser interferometer with a 3 km arm length, located in Kamioka, Gifu, Japan. In this series of articles, we present an overview of the baseline KAGRA, for which we finished installing the designed configuration in 2019. This article describes the method of calibration (CAL) used for reconstructing gravitational wave signals from the detector outputs, as well as the characterization of the detector (DET). We also review the physical environmental monitors (PEM) system and the geophysics interferometer (GIF). Both are used for characterizing and evaluating the data quality of the gravitational wave channel. They play important roles in utilizing the detector output for gravitational wave searches. These characterization investigations will be even more important in the near future, once gravitational wave detection has been achieved, and in using KAGRA in the gravitational wave astronomy era.

gr-qc↗

arXiv2019

An arm length stabilization system for KAGRA and future gravitational-wave detectors

Modern ground-based gravitational wave (GW) detectors require a complex interferometer configuration with multiple coupled optical cavities. Since achieving the resonances of the arm cavities is the most challenging among the lock acquisition processes, the scheme called arm length stabilization (ALS) had been employed for lock acquisition of the arm cavities. We designed a new type of the ALS, which is compatible with the interferometers having long arms like the next generation GW detectors. The features of the new ALS are that the control configuration is simpler than those of previous ones and that it is not necessary to lay optical fibers for the ALS along the kilometer-long arms of the detector. Along with simulations of its noise performance, an experimental test of the new ALS was performed utilizing a single arm cavity of KAGRA. This paper presents the first results of the test where we demonstrated that lock acquisition of the arm cavity was achieved using the new ALS and residual noise was measured to be $8.2\,\mathrm{Hz}$ in units of frequency, which is smaller than the linewidth of the arm cavity and thus low enough to lock the full interferometer of KAGRA in a repeatable and reliable manner.

physics.ins-det↗

arXiv2019

RAMSES II - RAMan Search for Extragalactic Symbiotic Stars. Project concept, commissioning, and early results from the science verification phase

Symbiotic stars (SySts) are long-period interacting binaries composed of a hot compact star, an evolved giant star, and a tangled network of gas and dust nebulae. They represent unique laboratories for studying a variety of important astrophysical problems, and have also been proposed as possible progenitors of SNIa. Presently, we know 257 SySts in the Milky Way and 69 in external galaxies. However, these numbers are still in striking contrast with the predicted population of SySts in our Galaxy. Because of other astrophysical sources that mimic SySt colors, no photometric diagnostic tool has so far demonstrated the power to unambiguously identify a SySt, thus making the recourse to costly spectroscopic follow-up still inescapable. In this paper we present the concept, commissioning, and science verification phases, as well as the first scientific results, of RAMSES II - a Gemini Observatory Instrument Upgrade Project that has provided each GMOS instrument at both Gemini telescopes with a set of narrow-band filters centered on the Raman OVI 6830 A band. Continuum-subtracted images using these new filters clearly revealed known SySts with a range of Raman OVI line strengths, even in crowded fields. RAMSES II observations also produced the first detection of Raman OVI emission from the SySt LMC 1 and confirmed Hen 3-1768 as a new SySt - the first photometric confirmation of a SySt. Via Raman OVI narrow-band imaging, RAMSES II provides the astronomical community with the first purely photometric tool for hunting SySts in the local Universe.

astro-ph.SR↗

arXiv2019

First cryogenic test operation of underground km-scale gravitational-wave observatory KAGRA

KAGRA is a second-generation interferometric gravitational-wave detector with 3-km arms constructed at Kamioka, Gifu in Japan. It is now in its final installation phase, which we call bKAGRA (baseline KAGRA), with scientific observations expected to begin in late 2019. One of the advantages of KAGRA is its underground location of at least 200 m below the ground surface, which brings small seismic motion at low frequencies and high stability of the detector. Another advantage is that it cools down the sapphire test mass mirrors to cryogenic temperatures to reduce thermal noise. In April-May 2018, we have operated a 3-km Michelson interferometer with a cryogenic test mass for 10 days, which was the first time that km-scale interferometer was operated at cryogenic temperatures. In this article, we report the results of this "bKAGRA Phase 1" operation. We have demonstrated the feasibility of 3-km interferometer alignment and control with cryogenic mirrors.

astro-ph.IM↗

arXiv2019

Vibration isolation system with a compact damping system for power recycling mirrors of KAGRA

A vibration isolation system called Type-Bp system used for power recycling mirrors has been developed for KAGRA, the interferometric gravitational-wave observatory in Japan. A suspension of the Type-Bp system passively isolates an optic from seismic vibration using three main pendulum stages equipped with two vertical vibration isolation systems. A compact reaction mass around each of the main stages allows for achieving sufficient damping performance with a simple feedback as well as vibration isolation ratio. Three Type-Bp systems were installed in KAGRA, and were proved to satisfy the requirements on the damping performance, and also on estimated residual displacement of the optics.

physics.ins-det↗

arXiv2018

KAGRA: 2.5 Generation Interferometric Gravitational Wave Detector

The recent detections of gravitational waves (GWs) reported by LIGO/Virgo collaborations have made significant impact on physics and astronomy. A global network of GW detectors will play a key role to solve the unknown nature of the sources in coordinated observations with astronomical telescopes and detectors. Here we introduce KAGRA (former name LCGT; Large-scale Cryogenic Gravitational wave Telescope), a new GW detector with two 3-km baseline arms arranged in the shape of an "L", located inside the Mt. Ikenoyama, Kamioka, Gifu, Japan. KAGRA's design is similar to those of the second generations such as Advanced LIGO/Virgo, but it will be operating at the cryogenic temperature with sapphire mirrors. This low temperature feature is advantageous for improving the sensitivity around 100 Hz and is considered as an important feature for the third generation GW detector concept (e.g. Einstein Telescope of Europe or Cosmic Explorer of USA). Hence, KAGRA is often called as a 2.5 generation GW detector based on laser interferometry. The installation and commissioning of KAGRA is underway and its cryogenic systems have been successfully tested in May, 2018. KAGRA's first observation run is scheduled in late 2019, aiming to join the third observation run (O3) of the advanced LIGO/Virgo network. In this work, we describe a brief history of KAGRA and highlights of main feature. We also discuss the prospects of GW observation with KAGRA in the era of O3. When operating along with the existing GW detectors, KAGRA will be helpful to locate a GW source more accurately and to determine the source parameters with higher precision, providing information for follow-up observations of a GW trigger candidate.

gr-qc↗

arXiv2016

Current-induced asymmetric magnetoresistance due to energy transfer via quantum spin-flip process

Current-induced magnetization excitation is a core phenomenon for next-generation magnetic nanodevices, and has been attributed to the spin-transfer torque (STT) that originates from the transfer of the spin angular momentum between a conduction electron and a local magnetic moment through the exchange coupling. However, the same coupling can transfer not only spin but also energy, though the latter transfer mechanism has been largely ignored. Here we report on experimental evidence concerning the energy transfer in ferromagnet/heavy metal bilayers. The magnetoresistance (MR) is found to depend significantly on the current direction down to low in-plane currents, for which STT cannot play any significant role. Instead we find that the observed MR is consistent with the energy transfer mechanism through the quantum spin-flip process, which predicts short wavelength, current-direction-dependent magnon excitations in the THz frequency range. Our results unveil another aspect of current-induced magnetic excitation, and open a channel for the dc-current-induced generation of THz magnons.

cond-mat.mtrl-sci↗

arXiv2006

Unitarity issue in BTZ black holes

We study the wave equation for a massive scalar in three-dimensional AdS-black hole spacetimes to understand the unitarity issues in a semiclassical way. Here we introduce four interesting spacetimes: the non-rotating BTZ black hole (NBTZ), pure AdS spacetime (PADS), massless BTZ black hole (MBTZ), and extremal BTZ black hole (EBTZ). Our method is based on the potential analysis and solving the wave equation to find the condition for the frequency $ω$ exactly. In the NBTZ case, one finds the quasinormal (complex and discrete) modes which signals for a non-unitary evolution. Real and discrete modes are found for the PADS case, which means that it is unitary obviously. On the other hand, we find real and continuous modes for the two extremal black holes of MBTZ and EBTZ. It suggests that these could be candidates for the unitary system.

hep-th↗

arXiv2005

Role of the Brans-Dicke scalar in the holographic description of dark energy

We study cosmological application of the holographic energy density in the Brans-Dicke theory. Considering the holographic energy density as a dynamical cosmological constant, it is more natural to study it in the Brans-Dicke theory than in general relativity. Solving the Friedmann and Brans-Dicke field equations numerically, we clarify the role of Brans-Dicke field during evolution of the universe. When the Hubble horizon is taken as the IR cutoff, the equation of state ($w_{\Lmd}$) for the holographic energy density is determined to be 5/3 when the Brans-Dicke parameter $\omg$ goes infinity. This means that the Brans-Dicke field plays a crucial role in determining the equation of state. For the particle horizon IR cutoff, the Brans-Dicke scalar mediates a transition from $w_{\Lmd} = -1/3$ (past) to $w_{\Lmd} = 1/3$ (future). If a dust matter is present, it determines future equation of state. In the case of future event horizon cutoff, the role of the Brans-Dicke scalar and dust matter are turned out to be trivial, whereas the holographic energy density plays an important role as a dark energy candidate with $w_{\Lmd} =-1$.

gr-qc↗

arXiv2005

Holographic energy density in the Brans-Dicke teory

We study cosmological applications of the holographic energy density. Considering the holographic energy density as a dynamical cosmological constant, we need the Brans-Dicke theory as a dynamical framework instead of general relativity. In this case we use the Bianchi identity as a consistency relation to obtain physical solutions. It is shown that the future event horizon as the IR cutoff provides the dark energy in the Brans-Dicke theory. Furthermore the role of the Brans-Dicke scalar is clarified in the dark energy-dominated universe by calculating its equation of state.

hep-th↗

arXiv2003

Dilatonic tachyon in Kerr-de Sitter space

We study the dynamical behavior of the dilaton in the background of three-dimensional Kerr-de Sitter space which is inspired from the low-energy string effective action. The Kerr-de Sitter space describes the gravitational background of a point particle whose mass and spin are given by $1-M$ and $J$ and its curvature radius is given by $\ell$. In order to study the propagation of metric, dilaton, and Kalb-Ramond two-form, we perform the perturbation analysis in the southern diamond of Kerr-de Sitter space including a conical singularity. It reveals a mixing between the dilaton and other unphysical fields. Introducing a gauge-fixing, we can disentangle this mixing completely and obtain one decoupled dilaton equation. However it turns out to be a tachyon with $m^2=-8/\ell^2$. We compute the absorption cross section for the dilatonic tachyon to extract information on the cosmological horizon of Kerr-de Sitter space. It is found that there is no absorption of the dilatonic tachyon in the presence of the cosmological horizon of Kerr-de Sitter space.

hep-th↗

arXiv2003

No absorption in de Sitter space

We study the wave equation for a minimally coupled massive scalar in D-dimensional de Sitter space. We compute the absorption cross section to investigate its cosmological horizon in the southern diamond. By analogy of the quantum mechanics, it is found that there is no absorption in de Sitter space. This means that de Sitter space is usually in thermal equilibrium, like the black hole in anti de Sitter space. It confirms that the cosmological horizon not only emits radiation but also absorbs that previously emitted by itself at the same rate, keeping the curvature radius of de Sitter space fixed.

hep-th↗

arXiv2002

Dynamical Behavior of dilaton in de Sitter space

We study the dynamical behavior of the dilaton in the background of three-dimensional Kerr-de Sitter space which is inspired from the low-energy string effective action. The perturbation analysis around the cosmological horizon of Kerr-de Sitter space reveals a mixing between the dilaton and other fields. Introducing a gauge (dilaton gauge), we can disentangle this mixing completely and obtain one decoupled dilaton equation. However it turns out that this belongs to the tachyon. The stability of de Sitter solution with J=0 is discussed. Finally we compute the dilaton absorption cross section to extract information on the cosmological horizon of de Sitter space.

hep-th↗

arXiv2001

Holographic principle in the BDL brane cosmology

We study the holographic principle in the brane cosmology. Especially we describe how to accommodate the 5D anti de Sitter Schwarzschild (AdSS$_5$) black hole in the Binetruy-Deffayet-Langlois (BDL) approach of brane cosmology. It is easy to make a connection between a mass $M$ of the AdSS$_5$ black hole and a conformal field theory (CFT)-radiation dominated universe on the brane in the moving domain wall approach. But this is not established in the BDL approach. In this case we use two parameters $C_1, C_2$ in the Friedmann equation. These arise from integration and are really related to the choice of initial bulk matter. If one chooses a bulk energy density $ρ_B$ to account for a mass $M$ of the AdSS$_5$ black hole and the static fifth dimension, a CFT-radiation term with $ρ_{CFT} \sim M/a^{4}$ comes out from the bulk matter without introducing a localized matter distribution on the brane. This means that the holographic principle can be established in the BDL brane cosmology.

hep-th↗