arXiv subjects
Publications and source records attributed to Haide Wang.
In this invited talk, we demonstrate the carrier leakage suppression and power difference equalization based on semiconductor optical amplifier (SOA) for TFDMA-based coherent PON, and propose a nonlinearity compensation algorithm to deal with SOA-induced nonlinear distortion.
To meet the high-speed, low-latency, and low-complexity demand for optical interconnects, simplified maximum likelihood sequence estimation (MLSE) is proposed in this paper. Simplified MLSE combines computational simplification and reduced state in MLSE. MLSE with a parallel sliding block architecture reduces latency from linear order to logarithmic order. Computational simplification reduces the number of multipliers from exponential order to linear order. Incorporating the reduced state with computational simplification further decreases the number of adders and comparators. The simplified MLSE is evaluated in a 112-Gbit/s PAM4 transmission over 2-km standard single-mode fiber. Experimental results show that the simplified MLSE significantly outperforms the FFE-only case in bit error ratio (BER) performance. Compared with simplified 1-step MLSE, the latency of simplified MLSE is reduced from 34 delay units in linear order to 7 delay units in logarithmic order. The simplified scheme in MLSE reduces the number of variable multipliers from 512 in exponential order to 33 in linear order without BER performance deterioration, while reducing the number of adders and comparators to 37.2% and 8.4%, respectively, with nearly identical BER performance.
Single-wavelength 400G coherent optical communications have become a critical solution to meet the explosive traffic demands. However, the single-carrier modulation using low-order modulation formats requires a broader wavelength division multiplexing grid and expands the occupied optical bandwidth. In this paper, we propose the faster-than-Nyquist non-orthogonal frequency division multiplexing (FTN-NOFDM) to improve the spectral efficiency for long-haul coherent optical communications. The subcarrier number is set to eight to enable low-complexity FTN-NOFDM signal generation using a pruned inverse fast Fourier transform and inter-carrier interference (ICI) cancellation. To deal with the conventional timing recovery (TR) failure, a frequency tone-based TR is proposed for FTN-NOFDM. A time-domain multiple-input multiple-output equalizer is designed to update the tap coefficients based on outputs of conventional iterative detection (ID). To further mitigate ICI, a low-density parity check-assisted ID is integrated into the conventional ID module. FTN-NOFDM, probabilistic constellation shaping (PCS)-OFDM, and quadrature phase shift keying-OFDM are experimentally compared in a 400G coherent optical communication system over 11 cascaded 125-GHz wavelength-selective switches (WSSs) and 2000 km transmission. Results show that the FTN-NOFDM exhibits comparable WSS filtering tolerance to PCS-OFDM and superior nonlinearity tolerance, while PCS-OFDM achieves the best bit error ratio performance.
Driven by the ever-increasing capacity demands, the 50G passive optical network (PON) is maturing gradually. One of the main challenges for the 50G PON is implementing burst-mode digital signal processing (BM-DSP) for the burst upstream signal. In this paper, we demonstrate a real-time BM-DSP for burst reception of 25Gbit/s on-off keying signal to meet the asymmetric-mode 50G PON demand. The real-time BM-DSP includes the BM frequency-domain timing recovery and BM frequency-domain equalizer, which can be fast converged based on the 42ns designed preamble. Meanwhile, the simplified implementations for fast-Fourier-transform, minimum-mean-square-error, and decision-directed least-mean-square-error algorithms decrease the DSP resources by 28.57%, enabling the loading of real-time BM-DSP in the field programmable gate array with the limited DSP resources. The real-time implementation of BM-DSP can guide the design of application-specific integrated circuits for 50G PON.
As the 50G optical access gradually matures, it is time to discuss Beyond 50G optical access. According to the evolution rules of optical access standards, Beyond 50G optical access data rate may achieve 200Gb/s. Direct detection faces great challenges for Beyond 50G optical access, which makes coherent detection a potential solution. Similar to 50G optical timing-division-multiple access (TDMA), burst-mode digital signal processing (BM-DSP) is also required for Beyond 50G coherent optical TDMA (CO-TDMA). This paper proposes coherent BM-DSP (Co-BM-DSP) based on approximately 10ns designed preambles to process the burst signal for 200G CO-TDMA, which can fast estimate the state of polarization, frequency offset, sampling phase offset, synchronization position, and equalizer coefficients. Meanwhile, for obtaining the equalizer coefficients based on the designed preamble, the channel estimation based on the minimum-mean-square-error criterion is theoretically proven to have a unique solution for ensuring reliability. In conclusion, the proposed Co-BM-DSP based on the designed preambles paves the way for the applications of Beyond 50G CO-TDMA.
A passive optical network (PON) based on non-orthogonal multiple access (NOMA) meets low latency and high capacity. In the NOMA-PON, the asynchronous clocks between the strong and weak optical network units (ONUs) cause the timing error and phase noise on the signal of the weak ONU. The theoretical derivation shows that the timing error and phase noise can be independently compensated. In this Letter, we propose a timing recovery (TR) algorithm based on an absolute timing error detector (Abs TED) and a pilot-based carrier phase recovery (CPR) to eliminate the timing error and phase noise separately. An experiment for 25G NOMA-PON is set up to verify the feasibility of the proposed algorithms. The weak ONU can achieve the 20% soft-decision forward error correction limit after compensating for timing error and phase noise. In conclusion, the proposed TR and the pilot-based CPR show great potential for the NOMA-PON.
Burst-mode DSP based on 10ns preamble is proposed for upstream reception of 200G coherent TDM-PON. The 128-symbol tone preamble is used for SOP, frequency offset, and sampling phase estimation, while the 192-symbol CAZAC preamble is used for frame synchronization and channel estimation.
Coherent point-to-multi-point (PtMP) optical network based on digital subcarrier multiplexing (DSCM) has been a promising technology for metro and access networks to achieve cost savings, low latency, and high flexibility. In-phase and quadrature (IQ) impairments of the coherent transceiver (e.g. IQ skew and power imbalance) cause severe performance degradation. In the DSCM-based coherent PtMP optical networks, it is hard to realize far-end IQ-impairments estimation for the hub transmitter because the leaf on one subcarrier cannot acquire the signal on the symmetrical subcarrier. In this paper, we propose a far-end IQ-impairments estimation based on the specially designed time-and-frequency interleaving tones (TFITs), which can simultaneously estimate IQ skews and power imbalances of the hub transmitter and leaf receiver at an individual leaf. The feasibility of the TFITs-based IQ-impairments estimation has been experimentally verified by setting up $8$Gbaud/SC $\times$ $4$SCs DSCM-based coherent PtMP optical network. The experimental results depict that the absolute errors in the estimated IQ skew and power imbalance are within $\pm 0.5$ps and $\pm 0.2$dB, respectively. In conclusion, TFITs-based IQ-impairments estimation has great potential for DSCM-based coherent PtMP optical networks.
The security issues of passive optical networks (PONs) have always been a concern due to broadcast transmission. Physical-layer security enhancement for the coherent PON should be as significant as improving transmission performance. In this paper, we propose the advanced encryption standard (AES) algorithm and geometric constellation shaping four-level pulse amplitude modulation (GCS-PAM4) pilot-based key distribution for secure coherent PON. The first bit of the GCS-PAM4 pilot is used for the hardware-efficient carrier phase recovery (CPR), while the second bit is utilized for key distribution without occupying the additional overhead. The key bits are encoded by the polar code to ensure error-free distribution. Frequent key updates are permitted for every codeword to improve the security of coherent PON. The experimental results of the 200-Gbps secure coherent PON using digital subcarrier multiplexing with 16-ary quadrature amplitude modulation show that the GCS-PAM4 pilot-based key distribution could be error-free at upstream transmission without occupying the additional overhead and the eavesdropping would be prevented by AES algorithm at downstream transmission. Moreover, there is almost no performance penalty on the CPR using the GCS-PAM4 pilot compared to the binary phase shift keying pilot.
Point-to-multi-point (PtMP) optical networks become the main solutions for network-edge applications such as passive optical networks and radio access networks. Entropy-loading digital subcarrier multiplexing (DSCM) is the core technology to achieve low latency and approach high capacity for flexible PtMP optical networks. However, the high peak-to-average power ratio of the entropy-loading DSCM signal limits the power budget and restricts the capacity, which can be reduced effectively by clipping operation. In this paper, we derive the theoretical capacity limitation of the flexible PtMP optical networks based on the entropy-loading DSCM signal. Meanwhile, an optimal clipping ratio for the clipping operation is acquired to approach the highest capacity limitation. Based on an accurate clipping-noise model under the optimal clipping ratio, we establish a three-dimensional look-up table for bit-error ratio, spectral efficiency, and link loss. Based on the three-dimensional look-up table, an optimization strategy is proposed to acquire optimal spectral efficiencies for achieving a higher capacity of the flexible PtMP optical networks.
To cope with the explosive bandwidth demand, significant progress has been made in the ITU-T standardization sector to define a higher-speed passive optical network (PON) with a 50Gb/s line rate. Recently, 50G PON becomes mature gradually, which means it is time to discuss beyond 50G PON. For ensuring an acceptable optical power budget, beyond 50G PON will potentially use coherent technologies, which can simultaneously promote the applications of flexible multiple access such as time/frequency-domain multiple access (TFDMA). In this paper, we will introduce the architectures, algorithms, and demonstrations for TFDMA-based coherent PON. The system architectures based on an ultra-simple coherent transceiver and specific signal spectra are designed to greatly reduce the cost of ONUs. Meanwhile, fast and low-complexity digital signal processing (DSP) algorithms are proposed for dealing with upstream and downstream signals. Based on the architectures and algorithms, we experimentally demonstrate the first real-time TFDMA-based coherent PON, which can support at most 256 end users, and peak line rates of 100Gb/s and 200Gb/s in the upstream and downstream scenarios, respectively. In conclusion, the proposed technologies for the coherent PON make it more possible to be applied in the future beyond 50G PON.
Beyond 100G passive optical networks (PONs) will be required to meet the ever-increasing traffic demand in the future. Coherent optical technologies are the competitive solutions for the future beyond 100G PON but also face challenges such as the high computational complexity of digital signal processing (DSP). A high oversampling rate in coherent optical technologies results in the high computational complexity of DSP. Therefore, DSP running in a non-integer-oversampling below 2 samples-per-symbol (sps) is preferred, which can not only reduce computational complexity but also obviously lower the requirement for the analog-to-digital converter. In this paper, we propose a non-integer-oversampling DSP for meeting the requirements of coherent PON. The proposed DSP working at 9/8-sps and 5/4-sps oversampling rates can be reduced by 44.04% and 40.78% computational complexity compared to that working at the 2-sps oversampling rate, respectively. Moreover, a 400-Gb/s-net-rate coherent PON based on digital subcarrier multiplexing was demonstrated to verify the feasibility of the non-integer-oversampling DSP. There is almost no penalty on the receiver sensitivity when the non-integer-oversampling DSP is adopted. In conclusion, the non-integer-oversampling DSP shows great potential in the future coherent PON.
We propose a timing recovery for point-to-multi-point coherent passive optical networks. The results show that the proposed algorithm has low complexity and better robustness against the residual chromatic dispersion.
We experimentally demonstrate a C band 100Gbit/s intensity modulation and direct detection entropy-loaded multi-rate Nyquist-subcarrier modulation signal over 100km dispersion-uncompensated link. A record capacity-reach of 10Tbit/s$\times$km is achieved.
In this paper, to the best of our knowledge, we propose the first multi-rate Nyquist-subcarriers modulation (SCM) for C-band 100Gbit/s signal transmission over 50km dispersion-uncompensated link. Chromatic dispersion (CD) introduces severe spectral nulls on optical double-sideband signal, which greatly degrades the performance of intensity-modulation and direct-detection systems. Based on the prior knowledge of the dispersive channel, Nyquist-SCM with multi-rate subcarriers is proposed to keep away from the CD-caused spectral nulls flexibly. Signal on each subcarrier can be individually recovered by a digital signal processing, including the feed-forward equalizer with no more than 31 taps, a two-tap post filter, and maximum likelihood sequence estimation with one memory length. Combining with entropy loading based on probabilistic constellation shaping to maximize the capacity-reach, the C-band 100Gbit/s multi-rate Nyquist-SCM signal over 50km dispersion-uncompensated link can achieve 7% hard-decision forward error correction limit and average normalized generalized mutual information of 0.967 at received optical power of -4dBm and optical signal-to-noise ratio of 47.67dB. In conclusion, the multi-rate Nyquist-SCM shows great potentials in solving the CD-caused spectral distortions.
In this paper, we present a field-trial C-band 72Gbit/s optical on-off keying (OOK) system over 18.8km dispersion-uncompensated submarine optical cable in the South China Sea. Chromatic dispersion (CD) of 18.8km submarine optical cable causes four spectral nulls on the 36GHz bandwidth of 72Gbit/s OOK signal, which is the main obstacle for achieving an acceptable bit-error-rate (BER) performance. Decision feedback equalizer (DFE) is effective to compensate for the spectral nulls. However, DFE has a serious defect of burst-error propagation when the burst errors emerge due to the unstable submarine environment. Weighted DFE (WDFE) can be used to mitigate the burst-error propagation, but it cannot fully compensate for the spectral nulls because only a part of feedback symbols is directly decided. Fortunately, maximum likelihood sequence estimation (MLSE) can be added after the WDFE to simultaneously eliminate the resisting spectral distortions and implement optimal detection. Compared to the joint DFE and MLSE algorithm, the joint WDFE and MLSE algorithm can effectively suppress the burst-error propagation to obtain a maximum 2.9dB improvement of $\boldsymbol{Q}$ factor and eliminate the phenomenon of BER floor. In conclusion, the joint WDFE and MLSE algorithm can solve the burst-error propagation for the field-trial fiber-optic communications.
In this paper, an optimized detection based on log-maximum a posteriori estimation with the fixed number of surviving states (fixed-state Log-MAP) is proposed to cooperate with equalizers to deal with the spectral distortions caused by limited bandwidth and chromatic dispersion for intensity-modulation and direct-detection (IM/DD) optical systems. The equalizers compensates the spectral distortions and optimized detection decodes the useful bits from the noise. For accurately extracting the bits from more serious noise, the optimized detection with larger memory length is required. However, the classical optimized detection such as maximum likelihood-sequence estimation (MLSE) requires exponential-growing computational complexity and storage with the increasing memory length. The fixed-state Log-MAP detection can decrease the computational complexity and storage from the exponential order to linear order. Therefore, the fixed-state Log-MAP detection can compensate more distortions compared to MLSE under the same hardware condition. We experimentally verify the fixed-state Log-MAP detection in a C-band 64 Gbit/s IM/DD on-off keying optical system over a 100 km dispersion-uncompensated link. Under the same hardware condition, the fixed-state Log-MAP detection has a 2 dB improvement of receiver sensitivity compared to MLSE. In conclusion, the fixed-state Log-MAP detection shows the potential for practical IM/DD optical systems.
In this paper, we propose adaptive channel-matched detection (ACMD) for C-band 64-Gbit/s intensity-modulation and direct-detection (IM/DD) optical on-off keying (OOK) system over a 100-km dispersion-uncompensated link. The proposed ACMD can adaptively compensate most of the link distortions based on channel and noise characteristics, which includes a polynomial nonlinear equalizer (PNLE), a decision feedback equalizer (DFE) and maximum likelihood sequence estimation (MLSE). Based on the channel characteristics, PNLE eliminates the linear and nonlinear distortions, while the followed DFE compensates the spectral nulls caused by chromatic dispersion. Finally, based on the noise characteristics, a post filter can whiten the noise for implementing optimal signal detection using MLSE. To the best of our knowledge, we present a record C-band 64-Gbit/s IM/DD optical OOK system over a 100 km dispersion-uncompensated link achieving 7\% hard-decision forward error correction limit using only the proposed ACMD at the receiver side. In conclusion, ACMD-based C-band 64-Gbit/s optical OOK system shows great potential for future optical interconnects.