arXiv subjects

Hana Ursic

Publications and source records attributed to Hana Ursic.

11 recordsLinked to original sources

arXiv2026

Improvement of piezocatalytic performance of Na0.5Bi0.5TiO3 perovskite using K doping for efficient Rhodamine B degradation

Piezocatalysis, based on the piezoelectric properties of catalysts, breaks down the barrier between mechanical energy and chemical energy. It describes the use of charges induced by piezoelectricity to assist typical chemical processes while harvesting various forms of mechanical green energy. The performance of piezocatalysis is predominantly governed by the piezoelectric properties of materials. The main aim of this work is to evaluate and analyze the potential of potassium doped sodium bismuth titanate Na0.5-xKxBi0.5TiO3 abbreviated as NKxBT (0, 0.15, 0.20, and 0.25), as a piezocatalyst in the degradation of the organic dye Rhodamine B RhB under ultrasonic vibration. The synthesis of NKxBT nanopowders was conducted using the sol-gel autocombustion method. Coupled structural analysis reveals the presence of an intermediate Morphotropic Phase Boundary (MPB, where two phases coexist) in the optimal NK15BT composition. The piezocatalytic degradation results showed a total piezo-degradation in only 90 min and a rate constant 8 times higher than the undoped NK0BT. The enhanced piezocatalytic activity results from a synergistic effect of MPB presence, reduced particle size, optimal bandgap and high lattice strain. The NK15BT sample also demonstrated good reusability and good mineralization.

cond-mat.mtrl-sci↗

arXiv2026

Multiferroic Properties of Electrospun CFO-BCTSn Nanocomposites for Magnetoelectric and Magnetic Field Sensing Applications

Multiferroic CFO-BCTSn composite nanofibers were synthesized using a sol-gel electrospinning method. Electron microscopy revealed well-defined fibers with diameters of 120-150 nm. Structural analyses using X-ray diffraction, Raman spectroscopy, and high-resolution transmission electron microscopy confirmed the coexistence of the spinel CFO phase and the perovskite BCTSn phase without detectable secondary phases. Magnetic hysteresis measurements demonstrated the magnetic behavior of the nanofibers, while piezoresponse force microscopy confirmed their piezoelectric properties. Magnetoelectric coupling was evidenced by differences between the magnetic hysteresis loops of electrically poled and unpoled samples. These lead-free composite nanofibers show potential for nanoscale magnetoelectric devices and magnetic field sensing applications.

cond-mat.mtrl-sci↗

arXiv2026

Ferroelectric KNbO3 nanoplatelets for thermally driven pyrocatalytic hydrogen evolution and dye degradation

Day- and night-induced thermal cycling offers a promising route for harvesting ambient thermal energy to drive sustainable hydrogen production and pollutant degradation. Pyroelectric materials enable this process by converting temperature fluctuations into surface charges capable of promoting catalytic water splitting and advanced oxidation reactions. In this work, we demonstrate efficient pyrocatalytic hydrogen evolution and Rhodamine B (RhB) degradation using orthorhombic ferroelectric Potassium niobate (KNbO$_3$) nanoplatelets (KN-np). Under thermal cycling between 20 and 50 $^\circ$C, KN-np achieved a hydrogen yield of 680 $μ$mol g$^{-1}$ after 30 thermal cycles, corresponding to an average hydrogen production rate of 22.67 $μ$mol g$^{-1}$ per cycle. In addition, KN-np exhibited excellent pyrocatalytic activity toward RhB degradation, reaching 84% removal after only 16 thermal cycles with an apparent kinetic rate constant of 0.11 cycle$^{-1}$. The remarkable catalytic performance is attributed to the strong spontaneous polarization and excellent pyroelectric properties of the KNbO$_3$ nanoplatelets, which promote efficient charge generation and interfacial redox reactions. These findings highlight the potential of KNbO$_3$ nanostructures as efficient pyrocatalysts for clean hydrogen production and environmental remediation.

cond-mat.mtrl-sci↗

arXiv2026

Tunable electrocaloric effect in lead scandium tantalate through calcium doping

State-of-the-art electrocaloric cooling prototypes rely on the conventional electrocaloric effect of ferroelectric lead scandium tantalate (PbSc0.5Ta0.5O3, PST), which peaks near room temperature. Here, we demonstrate that A-site calcium doping in highly ordered PST modifies its phase transitions and enables precise tuning of the electrocaloric response. The transition temperature shifts down to 258 K and up to 319 K, depending on Ca concentration. Calorimetry under electric field, electrical polarization loops, and piezoresponse force microscopy reveal the emergence of an intermediate antiferroelectric phase stabilized for Ca $\geq$ 2\%. These results are supported by first-principles calculations. We observe a conventional electrocaloric effect for Ca $\leq$ 2\% and an inverse electrocaloric effect at higher doping ($\geq$ 2\%). Under an applied field of 110 kV cm$^{-1}$, Ca-doped PST exhibits an adiabatic temperature change of 2 K over a range from 263 K to 353 K. Such Ca-doped PST compounds could be used to expand the temperature range of PST below the freezing point of water. Our results offer a pathway to cascaded electrocaloric cooling devices with extended operating spans.

cond-mat.mtrl-sci↗

arXiv2025

Current Advances in Magnetoelectric Composites with Various Interphase Connectivity Types

Magnetoelectric composites integrate the coupling between magnetic and piezoelectric materials to create new functionalities for potential technological applications. This coupling is typically achieved through the exchange of magnetic, electric, or elastic energy across the interfaces between the different constituent materials. Tailoring the strength of the magnetoelectric effect is primarily accomplished by selecting suitable materials for each constituent and by optimizing geometrical and microstructural designs. Various composite architectures, such as (0-3), (2-2), (1-3) and core-shell connectivities, have been studied to enhance magnetoelectric coupling and other required physical properties in composites. This review examines the latest advancements in magnetoelectric materials, focusing on the impact of different interphase connectivity types on their properties and performance. Before exploring magnetic-electric coupling, a brief overview of the historical background of multiferroic magnetoelectric composites is provided. Fundamental concepts underlying the magnetoelectric effect, piezoelectricity, and the magnetostrictive effect are explained, including their origins and examples of these materials' properties. So far, three types of magnetoelectric composite connectivities have been investigated experimentally: particulate composites (0-3), laminated and thin films (2-2), sticks embedded in matrix, core-shell particles, and coaxial fibers. An outlook on the prospects and scientific challenges in the field of multiferroic magnetoelectric composites is given at the end of this review.

cond-mat.mtrl-sci↗

arXiv2023

Effect of thermal annealing on dielectric and ferroelectric properties of aerosol-deposited $0.65\text{Pb}(\text{Mg}_{1/3}\text{Nb}_{2/3})\text{O}_{3}-0.35\text{PbTiO}_{3}$ thick films

In this work, the effects of thermal annealing at 500 °C on aerosol-deposited $0.65\text{Pb}(\text{Mg}_{1/3}\text{Nb}_{2/3})\text{O}_{3}-0.35\text{PbTiO}_{3}$ thick films on stainless-steel substrates are investigated using two complementary methods at high and low applied external electric fields. The first one is Positive Up Negative Down method, which allows us to obtain information about the switching and non-switching contributions to the polarization. It shows that the as-deposited film is ferroelectric before annealing, since it has a switching contribution to the polarization. After annealing, both the switching and non-switching contributions to polarization increased by a factor of 1.6 and 2.33, respectively, indicating stronger ferroelectric behavior. The second method is based on impedance spectroscopy coupled with Rayleigh analysis. The results show that post-deposition thermal annealing increases the reversible domain wall contribution to the dielectric permittivity by a factor 11 while keeping the threshold field similar. This indicates, after annealing, domain wall density is larger while domain wall mobility remains similar. These two complementary characterization methods show that annealing increases the ferroelectric behavior of the thick film by increasing the domain wall density and its influence is visible both on polarization versus electric field loop and dielectric permittivity.

cond-mat.mtrl-sci↗

arXiv2023

Magnetoelectric coupling in multiferroic CFO/BCTSn core shell nanofibers elaborated by co-axial electrospinning method

Multiferroic CoFe2O4-Ba0.95Ca0.05Ti0.89Sn0.11O3 core-shell nanofibers (CFO@BCTSn NFs) were synthesized by a sol-gel co-axial electrospinning technique. The scanning electron microscope and transmission electron microscope were used to check nanofibers' core-shell structure/configuration. X-ray diffraction and a high-resolution transmission electron microscope were used to confirm the spinel structure of CFO and the perovskite structure of BCTSn. The magnetic character of the resultant CFO@BCTSn NFs was determined by SQUID magnetometry. The piezoelectricity was verified using piezo-response force microscopy, which revealed an entirely covered ferroelectric shell outline, in accordance with SEM and TEM observations. The magnetoelectric (ME) coefficient was measured as a function of the applied external DC magnetic field. The maximum ME coefficient obtained for the CFO@BCTSn NFs was 346 mV cm-1 Oe-1. The high magnetoelectric coupling suggests that CFO@BCTSn NFs could be a promising candidate for magnetic field sensor and magnetoelectric device applications.

cond-mat.mtrl-sci↗

arXiv2023

Direct electrocaloric characterization of ceramic films

Reliable and accurate characterization of the electrocaloric effect is necessary to understand the intrinsic properties of materials. To date, several methods have been developed to directly measure the electrocaloric effect. However, each of them has some limitations, making them less suitable for characterizing ceramic films, which rely almost exclusively on less accurate indirect methods. Here, a new approach is proposed to address the process of rapid heat dissipation in ceramic films and to detect the electrically induced temperature change before it thermally bonds with the surrounding elements. By using a polymer substrate that slows heat dissipation to the substrate and fast infrared imaging, a substantial part of the adiabatic electrocaloric effect in Pb(Mg1/3Nb2/3)O3-based ceramic films is captured. Infrared imaging provides a robust technique to reduce the ratio between the adiabatic and the measured electrocaloric temperature change in micrometer-sized ceramic films to a single-digit number, ~3.5. The obtained results are validated with another direct thermometric method and compared with the results obtained with an indirect approach. Despite different measurement principles, the results obtained with the two direct methods agree well. The proposed approach is timely and could open a door to verify the predicted giant electrocaloric effects in ceramic films, thus accelerating the process of their integration into functional devices.

physics.app-ph↗

arXiv2020

Macroscopic polarization in the nominally ergodic relaxor state of lead magnesium niobate

Macroscopic polarity and its dynamic response to external electric fields and temperature in the nominally ergodic relaxor phase of pristine lead magnesium niobate crystals and ceramics, Pb(Mg1/3Nb2/3)O3 (PMN), were investigated. Dynamic pyroelectric measurements provide evidence for persistent macroscopic polarity of the samples. Annealing experiments below and above Burns temperature of polarized samples relate this polarity to the presence of polar nano entities and their dynamics. The dc electric field strength required for macroscopic polarization reversal is similar to the amplitude of the ac field where dynamic nonlinear dielectric permittivity reaches maximum. Consequently, the aforementioned maximum is related to the reorientation of polar nano entities. The results question the existence of an ergodic state in PMN below Burns temperature.

cond-mat.mtrl-sci↗

arXiv2016

A multicaloric material as a link between electrocaloric and magnetocaloric refrigeration

The existence and feasibility of the multicaloric, polycrystalline material 0.8Pb(Fe1/2Nb1/2)O3-0.2Pb(Mg1/2W1/2)O3, exhibiting magnetocaloric and electrocaloric properties, are demonstrated. Both the electrocaloric and magnetocaloric effects are observed over a broad temperature range below room temperature. The maximum magnetocaloric temperature change of ~0.26 K is obtained with a magnetic-field amplitude of 70 kOe at a temperature of 5 K, while the maximum electrocaloric temperature change of ~0.25 K is obtained with an electric-field amplitude of 60 kV/cm at a temperature of 180 K. The material allows a multicaloric cooling mode or a separate caloric-modes operation depending on the origin of the external field and the temperature at which the field is applied.

cond-mat.mtrl-sci↗

arXiv2013

Anelastic relaxor behavior of Pb(Mg1/3Nb2/3)O3

Elastic storage modulus and loss of relaxor lead magnesium niobate ceramics, Pb(Mg1/3Nb2/3)O3, have been measured with dynamic mechanical analyzer in single cantilever mode in the temperature range from 170 K to 320 K and at frequencies from 0.1 Hz to 50 Hz. The dependence of the elastic susceptibility (inverse modulus) on temperature and frequency of the driving force has characteristics of typical relaxor behavior that can be well described with the Vogel-Fulcher law. The parameters of the Vogel-Fulcher relation exhibit similar values for the dielectric and anelastic relaxations. Similarities and differences between anelastic and dielectric relaxor behaviors are identified.

cond-mat.mtrl-sci↗