arXiv subjects

Haocheng Hua

Publications and source records attributed to Haocheng Hua.

14 recordsLinked to original sources

arXiv2026

Rotating ULA-Enabled Computed Tomography for Efficient 3D Spatial Power Spectrum Synthesis: Architecture and Principled Orientation Design

This paper proposes an efficient three-dimensional (3D) spatial power spectrum synthesis method by rotating a uniform linear array (ULA) about its center in 3D space. Inspired by classical computed tomography (CT), the ULA performs analog receive combining at each rotation angle to produce a partial coherent sum. By collecting such sums over multiple rotations, the full 3D spectrum can be synthesized online via a single radio-frequency (RF) chain, without explicitly acquiring per-antenna signals. Depending on whether the overall coherent sum is accessible, the synthesis is obtained through either a minimum operation over partial spectrum images or joint synthesis after accumulating all coherent sums. Compared with fixed uniform planar array (UPA)-based combining and dense single movable-antenna (MA) sampling for 3D cubic virtual arrays, the proposed scheme achieves full-space 3D coverage with substantially reduced sampling and movement overhead while maintaining uniformly high angular resolution. Its sampling geometry and sequential orientation design also support pipelined analog beamforming, reducing practical hardware cost. To design rotation orientations in a principled manner without prior environmental information, we aim to maximize the expected worst-case projected separation between multi-path component (MPC) pairs. A secondary criterion then minimizes the worst-case projective correlation among orientation axes to reduce orientation redundancy. Accordingly, we optimize orientation sets for different numbers of orientations under isotropic-matrix and unit-norm constraints, using a multistart smooth minimax algorithm. Numerical results show that the optimized orientations uniformly span 3D space and reconstruct full-space 3D spectra close to the dense 3D cubic reference using only a fraction of spatial samples.

eess.SP↗

arXiv2026

Deep Learning-Empowered Movable-Antenna Position Optimization with Partial CSI

Movable antennas (MAs) are a promising technology to improve wireless data rates by dynamically adjusting their positions to avoid deep fading. However, finding the optimal MA positions requires full channel state information (CSI) for all possible locations within the movement region, creating massive channel estimation overhead. This paper proposes a deep neural network (DNN)-based learning framework to predict the optimal positions of multiple transmit MAs in a multi-user multiple-input single-output (MISO) system, entirely bypassing explicit channel estimation.First, we analyze a single-user MISO case, revealing a complex, highly nonlinear mapping between the optimal MA positions and the channel power gains from a specific subset of locations in the transmit region to the user. Because this mapping cannot be mathematically characterized for practical channel models, we train a DNN via supervised learning to capture it. The pre-trained DNN can then determine optimized MA positions in real-time relying only on partial power measurements from the transmit region.Extending this to multi-user scenarios is challenging due to complex rate expressions and the lack of globally optimal position solutions to use as training labels. To overcome this, we develop an unsupervised training framework that directly maximizes the multi-user sum-rate. This framework utilizes an attention-based architecture to extract latent features from the partial channel measurements and effectively manage inter-user interference. Simulation results show that our proposed approach achieves near-optimal performance in single-user systems and surpasses conventional CSI-based alternating optimization algorithms in multi-user environments.

eess.SP↗

arXiv2026

Two-timescale Optimization for Hybrid Mechanically and Electronically Tunable 6DMA Aided Communication

This letter proposes a hybrid mechanically and electronically tunable six-dimensional movable antenna (6DMA) base station (BS) architecture for future wireless communication networks. Such BS consists of multiple antenna arrays that are mechanically movable along a circular rail to adapt to the horizontal user hotspots, and each array is equipped with pattern reconfigurable antennas (PRAs) that are capable of electronically switching among a set of specified beam patterns to cater to the instantaneous user channels. The mechanical adjustment provides wide-angle coverage but suffers from slow response, while the electronic tuning enables rapid beam reconfiguration but with limited angular range. To effectively combine their complementary advantages, we propose to jointly design both mechanical and electronic configurations to maximize the average sum-rate of users via a two-timescale optimization approach, in which the array positions are optimized on the long timescale according to large-scale user distribution statistics, and the pattern selection vectors are optimized on the short timescale to enable fast beam alignment based on the instantaneous user locations. An alternating optimization algorithm based on the Monte Carlo sampling method is developed to solve the problem efficiently. Finally, simulation results show that our proposed design achieves significant performance gains over various benchmark schemes.

cs.IT↗

arXiv2025

Hierarchically Tunable 6DMA for Wireless Communication and Sensing: Modeling and Performance Optimization

This paper proposes a new hierarchically tunable six-dimensional movable antenna (HT-6DMA) architecture for base station (BS) in future wireless networks. The HT-6DMA BS consists of multiple antenna arrays that can flexibly move on a spherical surface, with their three-dimensional (3D) positions and 3D rotations/orientations efficiently characterized in the global spherical coordinate system (SCS) and their individual local SCSs, respectively. As a result, the 6DMA system is hierarchically tunable in the sense that each array's global position and local rotation can be separately adjusted in a sequential manner with the other being fixed, thus greatly reducing their design complexity and improving the achievable performance. In particular, we consider an HT-6DMA BS serving multiple single-antenna users in the uplink communication or sensing potential unmanned aerial vehicles (UAVs)/drones in a given airway area. Specifically, for the communication scenario, we aim to maximize the average sum rate of communication users in the long term by optimizing the positions and rotations of all 6DMA arrays at the BS. While for the airway sensing scenario, we maximize the minimum received sensing signal power along the airway by optimizing the 6DMA arrays' positions and rotations along with the BS's transmit covariance matrix. Despite that the formulated problems are both non-convex, we propose efficient solutions to them by exploiting the hierarchical tunability of positions/rotations of 6DMA arrays in our proposed model. Numerical results show that the proposed HT-6DMA design significantly outperforms not only the traditional BS with fixed-position antennas (FPAs), but also the existing 6DMA scheme. Furthermore, it is unveiled that the performance gains of HT-6DMA mostly come from the arrays' global position adjustments on the spherical surface, rather than their local rotation adjustments.

eess.SP↗

arXiv2024

Near-Field Integrated Sensing and Communication with Extremely Large-Scale Antenna Array

This paper studies a near-field integrated sensing and communication (ISAC) system with extremely large-scale antenna array (ELAA), in which a base station (BS) deployed with enormous number of antennas transmits wireless signals to communicate with multiple communication users (CUs) and simultaneously uses the echo signals to localize multiple point targets in the three-dimension (3D) space. To balance the performance tradeoff between communication and target localization, we design the transmit covariance matrix at the BS to optimize the localization performance while ensuring the signal-to-interference-plus-noise ratio (SINR) constraints at individual CUs. In particular, we formulate three design problems by considering different 3D localization performance metrics, including minimizing the sum Cramér-Rao bound (CRB), maximizing the minimum target illumination power, and maximizing the minimum target echo signal power. Although the three design problems are non-convex in general, we obtain their global optimal solutions via the technique of semi-definite relaxation (SDR). It is shown that the three problems have low-rank solution structures depending on the sensing and communication channel matrices, helping reduce the complexity of the SDR-based solutions. Interestingly, we find that in the special case with a single collocated target/CU present towards the middle of a symmetric uniform planar array (UPA), the optimal solutions to the three problems become identical to the SINR-maximization design and have a closed form, while in other cases they can be different in general. Besides, when the target/CU moves away from the transmitter/receiver, the CRB may first decrease and then increase. These two phenomena differ from those in the far-field. Numerical results show the benefits of the proposed designs for near-field ISAC, by exploiting the beam focusing capabilities of ELAA.

eess.SP↗

arXiv2023

An Overview on IEEE 802.11bf: WLAN Sensing

With recent advancements, the wireless local area network (WLAN) or wireless fidelity (Wi-Fi) technology has been successfully utilized to realize sensing functionalities such as detection, localization, and recognition. However, the WLANs standards are developed mainly for the purpose of communication, and thus may not be able to meet the stringent requirements for emerging sensing applications. To resolve this issue, a new Task Group (TG), namely IEEE 802.11bf, has been established by the IEEE 802.11 working group, with the objective of creating a new amendment to the WLAN standard to meet advanced sensing requirements while minimizing the effect on communications. This paper provides a comprehensive overview on the up-to-date efforts in the IEEE 802.11bf TG. First, we introduce the definition of the 802.11bf amendment and its formation and standardization timeline. Next, we discuss the WLAN sensing use cases with the corresponding key performance indicator (KPI) requirements. After reviewing previous WLAN sensing research based on communication-oriented WLAN standards, we identify their limitations and underscore the practical need for the new sensing-oriented amendment in 802.11bf. Furthermore, we discuss the WLAN sensing framework and procedure used for measurement acquisition, by considering both sensing at sub-7GHz and directional multi-gigabit (DMG) sensing at 60 GHz, respectively, and address their shared features, similarities, and differences. In addition, we present various candidate technical features for IEEE 802.11bf, including waveform/sequence design, feedback types, as well as quantization and compression techniques. We also describe the methodologies and the channel modeling used by the IEEE 802.11bf TG for evaluation. Finally, we discuss the challenges and future research directions to motivate more research endeavors towards this field in details.

eess.SP↗

arXiv2023

Near-Field 3D Localization via MIMO Radar: Cramér-Rao Bound Analysis and Estimator Design

This paper studies a near-field multiple-input multiple-output (MIMO) radar sensing system, in which the transceivers with massive antennas aim to localize multiple near-field targets in the three-dimensional (3D) space over unknown cluttered environments. We consider a spherical wavefront propagation with both channel phase and amplitude variations over different antennas. Under this setup, the unknown parameters include the 3D coordinates and complex reflection coefficients of the targets, as well as the noise and interference covariance matrix. First, by considering general transmit signal waveforms, we derive the Fisher information matrix (FIM) corresponding to the 3D coordinates and the complex reflection coefficients of the targets and accordingly obtain the Cramér-Rao bound (CRB) for the 3D coordinates. This provides a performance bound for 3D near-field target localization. For the special single-target case, we obtain the CRB in an analytical form, and analyze its asymptotic scaling behaviors with respect to the target distance and antenna size of the transceiver. Next, to facilitate practical localization, we propose two estimators to localize targets based on the maximum likelihood (ML) criterion, namely the 3D approximate cyclic optimization (3D-ACO) and the 3D cyclic optimization with white Gaussian noise (3D-CO-WGN), respectively. Numerical results validate the asymptotic CRB analysis and show that the consideration of varying channel amplitudes is vital to achieve accurate CRB and localization when the targets are close to the transceivers. It is also shown that the proposed estimators achieve localization performance close to the derived CRB under various cluttered environments, thus validating their effectiveness in practical implementation. Furthermore, it is shown that transmit waveforms have a significant impact on CRB and the localization performance.

cs.IT↗

arXiv2023

ISAC Meets SWIPT: Multi-functional Wireless Systems Integrating Sensing, Communication, and Powering

This paper unifies integrated sensing and communication (ISAC) and simultaneous wireless information and power transfer (SWIPT), by investigating a new multi-functional multiple-input multiple-output (MIMO) system integrating wireless sensing, communication, and powering. In this system, one multi-antenna hybrid access point (H-AP) transmits wireless signals to communicate with one multi-antenna information decoding (ID) receiver, wirelessly charge one multi-antenna energy harvesting (EH) receiver, and perform radar target sensing based on the echo signal at the same time. Under this setup, we aim to reveal the fundamental performance tradeoff limits among sensing, communication, and powering, in terms of the estimation Cramer-Rao bound (CRB), achievable communication rate, and harvested energy level, respectively. In particular, we consider two different target models for radar sensing, namely the point and extended targets, for which we are interested in estimating the target angle and the complete target response matrix, respectively. For both models, we define the achievable CRB-rate-energy (C-R-E) region and characterize its Pareto boundary by maximizing the achievable rate at the ID receiver, subject to the estimation CRB requirement for target sensing, the harvested energy requirement at the EH receiver, and the maximum transmit power constraint at the H-AP. We obtain the well-structured optimal transmit covariance solutions to the two formulated problems by applying advanced convex optimization techniques. Numerical results show the optimal C-R-E region boundary achieved by our proposed design, as compared to the benchmark schemes based on time switching and eigenmode transmission (EMT).

cs.IT↗

arXiv2023

Near-Field 3D Localization via MIMO Radar: Cramér-Rao Bound and Estimator Design

Future sixth-generation (6G) networks are envisioned to provide both sensing and communications functionalities by using densely deployed base stations (BSs) with massive antennas operating in millimeter wave (mmWave) and terahertz (THz). Due to the large number of antennas and the high frequency band, the sensing and communications will operate within the near-field region, thus making the conventional designs based on the far-field channel models inapplicable. This paper studies a near-field multiple-input-multiple-output (MIMO) radar sensing system, in which the transceivers with massive antennas aim to localize multiple near-field targets in the three-dimensional (3D) space. In particular, we adopt a general wavefront propagation model by considering the exact spherical wavefront with both channel phase and amplitude variations over different antennas. Besides, we consider the general transmit signal waveforms and also consider the unknown cluttered environments. Under this setup, the unknown parameters to estimate include the 3D coordinates and the complex reflection coefficients of the multiple targets, as well as the noise and interference covariance matrix. Accordingly, we derive the Cramér-Rao bound (CRB) for estimating the target coordinates. Next, to facilitate practical localization, we propose an efficient estimator based on the 3D approximate cyclic optimization (3D-ACO), which is obtained following the maximum likelihood (ML) criterion. Finally, numerical results show that considering the exact antenna-varying channel amplitudes achieves more accurate CRB as compared to prior works based on constant channel amplitudes across antennas, especially when the targets are close to the transceivers. It is also shown that the proposed estimator achieves localization performance close to the derived CRB, thus validating its superior performance.

cs.IT↗

arXiv2023

Optimal Transmit Beamforming for Integrated Sensing and Communication

This paper studies the transmit beamforming in a downlink integrated sensing and communication (ISAC) system, where a base station (BS) equipped with a uniform linear array (ULA) sends combined information-bearing and dedicated radar signals to simultaneously perform downlink multiuser communication and radar target sensing. Under this setup, we maximize the radar sensing performance (in terms of minimizing the beampattern matching errors or maximizing the minimum weighted beampattern gains), subject to the communication users' minimum signal-to-interference-plus-noise ratio (SINR) requirements and the BS's transmit power constraints. In particular, we consider two types of communication receivers, namely Type-I and Type-II receivers, which do not have and do have the capability of cancelling the interference from the {\emph{a-priori}} known dedicated radar signals, respectively. Under both Type-I and Type-II receivers, the beampattern matching and minimum weighted beampattern gain maximization problems are globally optimally solved via applying the semidefinite relaxation (SDR) technique together with the rigorous proof of the tightness of SDR for both Type-I and Type-II receivers under the two design criteria. It is shown that at the optimality, radar signals are not required with Type-I receivers under some specific conditions, while radar signals are always needed to enhance the performance with Type-II receivers. Numerical results show that the minimum weighted beampattern gain maximization leads to significantly higher beampattern gains at the worst-case sensing angles with a much lower computational complexity than the beampattern matching design. We show that by exploiting the capability of canceling the interference caused by the radar signals, the case with Type-II receivers results in better sensing performance than that with Type-I receivers and other conventional designs.

cs.IT↗

arXiv2022

Transmit Optimization for Multi-functional MIMO Systems Integrating Sensing, Communication, and Powering

This paper unifies integrated sensing and communication (ISAC) and simultaneous wireless information and power transfer (SWIPT), by investigating a new multi-functional multiple-input multiple-output (MIMO) system integrating wireless sensing, communication, and powering. In this system, one multi-antenna hybrid access point (H-AP) transmits wireless signals to communicate with one multi-antenna information decoding (ID) receiver, wirelessly charge one multi-antenna energy harvesting (EH) receiver, and perform radar sensing for a point target based on the echo signal at the same time. Under this setup, we aim to reveal the fundamental performance tradeoff limits of sensing, communication, and powering, in terms of the estimation Cram{é}r-Rao bound (CRB), achievable communication rate, and harvested energy level, respectively. Towards this end, we define the achievable CRB-rate-energy (C-R-E) region and characterize its Pareto boundary by maximizing the achievable rate at the ID receiver, subject to the estimation CRB requirement for target sensing, the harvested energy requirement at the EH receiver, and the maximum transmit power constraint at the H-AP. We obtain the semi-closed-form optimal transmit covariance solution to the formulated problem by applying advanced convex optimization techniques. Numerical results show the optimal C-R-E region boundary achieved by our proposed design, as compared to the benchmark scheme based on time switching.

cs.IT↗

arXiv2022

MIMO Integrated Sensing and Communication: CRB-Rate Tradeoff

This paper studies a multiple-input multiple-output (MIMO) integrated sensing and communication (ISAC) system, in which a multi-antenna base station (BS) sends unified wireless signals to estimate one sensing target and communicate with a multi-antenna communication user (CU) simultaneously. We consider both the point and extended target models. For the point target case, the BS estimates the target angle and we adopt the Cramér-Rao bound (CRB) for angle estimation as the sensing performance metric. For the extended target case, the BS estimates the complete target response matrix, and we consider three different sensing performance metrics including the trace, the maximum eigenvalue, and the determinant of the CRB matrix for target response matrix estimation. For each of the four scenarios with different CRB measures, we investigate the fundamental tradeoff between the CRB for estimation and the data rate for communication, by characterizing the Pareto boundary of the achievable CRB-rate (C-R) region. In particular, we formulate a new MIMO rate maximization problem for each scenario, by optimizing the transmit covariance matrix at the BS, subject to a different form of maximum CRB constraint and its maximum transmit power constraint. For these problems, we obtain their optimal solutions in semi-closed forms by using advanced convex optimization techniques. For the point target case, the optimal solution is obtained by diagonalizing a \emph{composite channel matrix} via singular value decomposition (SVD) together with water-filling-like power allocation over these decomposed subchannels. For the three scenarios in the extended target case, the optimal solutions are obtained by diagonalizing the \emph{communication channel} via SVD, together with proper power allocation over two orthogonal sets of subchannels. Numerical results are conducted to validate the proposed design.

cs.IT↗

arXiv2022

MIMO Integrated Sensing and Communication with Extended Target: CRB-Rate Tradeoff

This paper studies a multiple-input multiple-output (MIMO) integrated sensing and communication (ISAC) system, in which a multi-antenna base station (BS) sends unified wireless signals to estimate an extended target and communicate with a multi-antenna communication user (CU) at the same time. We investigate the fundamental tradeoff between the estimation Cramér-Rao bound (CRB) for sensing and the data rate for communication, by characterizing the Pareto boundary of the achievable CRB-rate (C-R) region. Towards this end, we formulate a new MIMO rate maximization problem by optimizing the transmit covariance matrix at the BS, subject to a new form of maximum CRB constraint together with a maximum transmit power constraint. We derive the optimal transmit covariance solution in a semi-closed form, by first implementing the singular-value decomposition (SVD) to diagonalize the communication channel and then properly allocating the transmit power over these subchannels for communication and other orthogonal subchannels (if any) for dedicated sensing. It is shown that the optimal transmit covariance is of full rank, which unifies the conventional rate maximization design with water-filling power allocation and the CRB minimization design with isotropic transmission. Numerical results are provided to validate the performance achieved by our proposed optimal design, in comparison with other benchmark schemes.

cs.IT↗

arXiv2022

Joint transmit and reflective beamforming for IRS-assisted integrated sensing and communication

This paper studies an intelligent reflecting surface (IRS)-assisted integrated sensing and communication (ISAC) system, in which one IRS is deployed to not only assist the wireless communication from a multi-antenna base station (BS) to a single-antenna communication user (CU), but also create virtual line-of-sight (LoS) links for sensing targets at areas with LoS links blocked. We consider that the BS transmits combined information and sensing signals for ISAC. Under this setup, we jointly optimize the transmit information and sensing beamforming at the BS and the reflective beamforming at the IRS, to maximize the IRS's minimum beampattern gain towards the desired sensing angles, subject to the minimum signal-to-noise ratio (SNR) requirement at the CU and the maximum transmit power constraint at the BS. Although the formulated SNR-constrained beampattern gain maximization problem is non-convex and difficult to solve, we present an efficient algorithm to obtain a high-quality solution using alternating optimization and semi-definite relaxation (SDR). Numerical results show that the proposed joint beamforming design achieves improved sensing performance while ensuring the communication requirement as compared to benchmarks without such joint optimization. It is also shown that the use of dedicated sensing beams is beneficial in enhancing the performance for IRS-assisted ISAC.

eess.SP↗