arXiv subjects

Heng Ban

Publications and source records attributed to Heng Ban.

9 recordsLinked to original sources

arXiv2026

Anisotropic Thermal Characterization of Suspended and Spin-Coated Polyimide Films Using a Square-Pulsed Source Method

Polyimide (PI) thin films are widely used in advanced technologies, yet accurate characterization of their thermal properties remains challenging, as evidenced by significant inconsistencies in reported data and an incomplete understanding of heat transfer mechanisms. In this study, we employ an optical Square-Pulsed Source (SPS) technique to simultaneously measure the in-plane and cross-plane thermal conductivities, as well as the volumetric heat capacity, of PI thin films. SPS is a pump-probe method that utilizes a square-wave-modulated pump laser to induce periodic heating and a probe laser to detect the thermoreflectance response. Thermal properties are extracted by analyzing amplitude signals across multiple modulation frequencies and laser spot sizes. Measurements were conducted on both suspended commercial PI films and spin-coated PI films on fused silica substrates. The results show that spin-coated films exhibit higher cross-plane thermal conductivity and lower anisotropy compared to suspended films, which we attribute to differences in molecular orientation and substrate interactions. These findings provide new physical insights into anisotropic heat transport in polymer thin films and demonstrate the SPS technique as a robust tool for probing microscale thermal phenomena in soft materials.

physics.app-ph↗

arXiv2025

Three-dimensional (3D) tensor-based methodology for characterizing 3D anisotropic thermal conductivity tensor

The increasing complexity of advanced materials with anisotropic thermal properties necessitates more generic and efficient methods to determine three-dimensional (3D) anisotropic thermal conductivity tensors with up to six independent components. Current methods rely on a vector-based framework that can handle only up to four independent components, often leading to inefficiencies and inaccuracies. We introduce Three-Dimensional Spatially Resolved Lock-In Micro-Thermography (3D SR-LIT), a novel optical thermal characterization technique combining a 3D tensor-based framework with an efficient area-detection experimental system. For simple tensors (e.g., x-cut quartz, k_xz=k_yz=0), our method reduces uncertainty by over 50% compared to vector-based methods. For complex tensors with six independent components (e.g., AT-cut quartz), 2{\sigma} uncertainties remain below 12% for all components. A novel adaptive mapping approach enables high-throughput data acquisition (40 seconds to 3 minutes, depending on tensor complexity), over 35 times faster than current methods, and accommodates samples with 200 nm surface roughness. Extensive numerical validation on 1,000 arbitrary anisotropic tensors ranging from 1 to 1,000 Wm^(-1) K^(-1) further validates the robustness of this methodology. This work highlights significant advancements in thermal characterization of complex anisotropic materials.

cond-mat.mtrl-sci↗

arXiv2024

Analyzing Errors in Controlled Turret System

The purpose of this paper is to characterize aiming errors in controlled weapon systems given target location as input. To achieve this objective, we analyze the accuracy of a controlled weapon system model for stationary and moving targets under different error sources and firing times. First, we develop a mathematical model of a gun turret and use it to design two controllers, a Proportional-Integral-Derivative controller and a Model Predictive controller, which accept the target location input and move the turret to the centroid of the target in simulations. For stationary targets, we analyze the impact of errors in estimating the system's parameters and uncertainty in the aim point measurement. Our results indicate that turret movement is more sensitive to errors in the moment of inertia than the damping coefficient, which could lead to incorrect simulations of controlled turret system accuracy. The results also support the hypothesis that turret movement errors are larger over longer distances of gun turret movement and, assuming no time constraints, accuracy improves the longer one waits to fire; though this may not always be practical in a combat scenario. Additionally, we demonstrate that the integral control component is needed for high accuracy in moving target scenarios.

eess.SY↗

arXiv2024

Analyzing Errors in Controlled Turret System Given Target Location Input from Artificial Intelligence Methods in Automatic Target Recognition

In this paper, we assess the movement error of a targeting system given target location data from artificial intelligence (AI) methods in automatic target recognition (ATR) systems. Few studies evaluate the impacts on the accuracy in moving a targeting system to an aimpoint provided in this manner. To address this knowledge gap, we assess the performance of a controlled gun turret system given target location from an object detector developed from AI methods. In our assessment, we define a measure of object detector error and examine the correlations with several standard metrics in object detection. We then statistically analyze the object detector error data and turret movement error data acquired from controlled targeting simulations, as well as their aggregate error, to examine the impact on turret movement accuracy. Finally, we study the correlations between additional metrics and the probability of a hit. The results indicate that AI technologies are a significant source of error to targeting systems. Moreover, the results suggest that metrics such as the confidence score, intersection-over-union, average precision and average recall are predictors of accuracy against stationary targets with our system parameters.

eess.SY↗

arXiv2024

Spatially resolved lock-in micro-thermography (SR-LIT): A tensor analysis-enhanced method for anisotropic thermal characterization

While high-throughput (HT) computations have streamlined the discovery of promising new materials, experimental characterization remains challenging and time-consuming. One significant bottleneck is the lack of an HT thermal characterization technique capable of analyzing advanced materials exhibiting varying surface roughness and in-plane anisotropy. To tackle these challenges, we introduce spatially resolved lock-in micro-thermography (SR-LIT), an innovative technique enhanced by tensor analysis for optical thermal characterization. Our comprehensive analysis and experimental findings showcase notable advancements: We present a novel tensor-based methodology that surpasses the limitations of vector-based analysis prevalent in existing techniques, significantly enhancing the characterization of arbitrary in-plane anisotropic thermal conductivity tensors. On the instrumental side, we introduce a straightforward camera-based detection system that, when combined with the tensor-based methodology, enables HT thermal measurements. This technique requires minimal sample preparation and enables the determination of the entire in-plane thermal conductivity tensor with a single data acquisition lasting under 40 seconds, demonstrating a time efficiency over 90 times superior to state-of-the-art HT thermology. Additionally, our method accommodates millimeter-sized samples with poor surface finish, tolerating surface roughness up to 3.5 {\mu}m. These features highlight an innovative approach to realizing HT and accurate thermal characterization across various research areas and real-world applications.

physics.app-ph↗

arXiv2022

An Application of a Modified Beta Factor Method for the Analysis of Software Common Cause Failures

This paper presents an approach for modeling software common cause failures (CCFs) within digital instrumentation and control (I&C) systems. CCFs consist of a concurrent failure between two or more components due to a shared failure cause and coupling mechanism. This work emphasizes the importance of identifying software-centric attributes related to the coupling mechanisms necessary for simultaneous failures of redundant software components. The groups of components that share coupling mechanisms are called common cause component groups (CCCGs). Most CCF models rely on operational data as the basis for establishing CCCG parameters and predicting CCFs. This work is motivated by two primary concerns: (1) a lack of operational and CCF data for estimating software CCF model parameters; and (2) the need to model single components as part of multiple CCCGs simultaneously. A hybrid approach was developed to account for these concerns by leveraging existing techniques: a modified beta factor model allows single components to be placed within multiple CCCGs, while a second technique provides software-specific model parameters for each CCCG. This hybrid approach provides a means to overcome the limitations of conventional methods while offering support for design decisions under the limited data scenario.

cs.SE↗

arXiv2022

A new spatial-scan thermoreflectance method to measure a broad range of anisotropic in-plane thermal conductivity

In-plane thermal conductivities of small-scale samples are hard to measure, especially for the lowly conductive ones and those lacking in-plane symmetry (i.e., transversely anisotropic materials). State-of-the-art pump-probe techniques including both the time-domain and the frequency-domain thermoreflectance (TDTR and FDTR) are advantageous in measuring the thermal conductivity of small-scale samples, and various advanced TDTR and FDTR techniques have been developed to measure transversely anisotropic materials. However, the measurable in-plane thermal conductivity (k_in) is usually limited to be >10 W/(m K). In this work, a new spatial-scan thermoreflectance (SSTR) method has been developed to measure a broad range of k_in of millimeter-scale small samples, including those lacking in-plane symmetry, extending the current limit of the measurable k_in to as low as 1 W/(m K). This SSTR method establishes a new scheme of measurements using the optimized laser spot size and modulation frequency and a new scheme of data processing, enabling measurements of in-plane thermal conductivity tensors of a broad range of k_in values with both high accuracy and ease of operation. Some details such as the requirement on the sample geometry, the effect of the transducer layer, and the effect of heat loss are also discussed. As a verification, the k_in of some transversely isotropic reference samples with a wide range of k_in values including fused silica, sapphire, silicon, and highly ordered pyrolytic graphite (HOPG) have been measured using this new SSTR method. The measured k_in agree perfectly well with the literature values with a typical uncertainty of 5%. As a demonstration of the unique capability of this method, the in-plane thermal conductivity tensor of x-cut quartz, an in-plane anisotropic material, has also been measured.

cond-mat.mtrl-sci↗

arXiv2020

A Redundancy-Guided Approach for the Hazard Analysis of Digital Instrumentation and Control Systems in Advanced Nuclear Power Plants

Digital instrumentation and control (I&C) upgrades are a vital research area for nuclear industry. Despite their performance benefits, deployment of digital I&C in nuclear power plants (NPPs) has been limited. Digital I&C systems exhibit complex failure modes including common cause failures (CCFs) which can be difficult to identify. This paper describes the development of a redundancy-guided application of the Systems-Theoretic Process Analysis (STPA) and Fault Tree Analysis (FTA) for the hazard analysis of digital I&C in advanced NPPs. The resulting Redundancy-guided System-theoretic Hazard Analysis (RESHA) is applied for the case study of a representative state-of-the-art digital reactor trip system. The analysis qualitatively and systematically identifies the most critical CCFs and other hazards of digital I&C systems. Ultimately, RESHA can help researchers make informed decisions for how, and to what degree, defensive measures such as redundancy, diversity, and defense-in-depth can be used to mitigate or eliminate the potential hazards of digital I&C systems.

eess.SY↗

arXiv2019

Transient and Steady-State Temperature Rise in Three-Dimensional Anisotropic Layered Structures in Pump-Probe Thermoreflectance Experiments

Recent developments of the pump-probe thermoreflectance methods (such as the beam-offset and elliptical-beam approaches of the time-domain and frequency-domain thermoreflectance techniques) enabled measurements of the thermal conductivities of in-plane anisotropic materials. Estimating the temperature rise of anisotropic layered structures under surface heating is critically important to make sure that the temperature rise is not too high to alias the signals in these experiments. However, a simple formula to estimate the temperature rise in three-dimensional (3D) anisotropic layered systems heated by a non-circular laser beam is not available yet, which is the main problem we aim to solve in this work. We first re-derived general formalisms of the temperature rise of a multilayered structure based on the previous literature work by solving the 3D anisotropic heat diffusion equation in the frequency domain. These general formalisms normally require laborious numerical evaluation; however, they could be reduced to explicit analytical expressions for the case of semi-infinite solids. We then extend the analytical expressions to multilayered systems, taking into account the effect of the top layers. This work not only enhances our understanding of the physics of temperature rise due to surface laser heating but also enables quick estimation of the peak temperature rise of 3D anisotropic layered systems in pump-probe thermoreflectance experiments and thus greatly benefits the thermoreflectance experiments in choosing the appropriate heating power intensity for the experiments.

physics.app-ph↗