arXiv subjects

Henri-François Raynaud

Publications and source records attributed to Henri-François Raynaud.

9 recordsLinked to original sources

arXiv2026

The MICADO first-light imager for the ELT: first steps of the SCAO system MAIT

MICADO is the ELT first light instrument, an imager working at the diffraction limit of the telescope thanks to two adaptive optics (AO) modes: a single conjugate one (SCAO), available at the instrument first light and developed by the MICADO consortium, and a multi conjugate one (MCAO), developed by the MORFEO consortium. Although the project final design review process is about to be completed, the review board and ESO acknowledged that "the review of the final design can be considered complete for the majority of the MICADO sub-systems" and agreed that MICADO can start manufacturing. For the MICADO SCAO module, we have started the manufacturing of several parts: the majority of the SCAO optics and of the SCAO mechanics, the real-time computer software and the instrument control software. This manufacturing is ordered in several steps to allow the progressive integration of a first full AO close loop with the final SCAO parts. In this contribution, we will focus on the first two steps: on our AO Sésame bench and the so-called "beta flat configuration". We will present the status of this manufacturing and the first results obtained.

astro-ph.IM↗

arXiv2026

The MICADO first light imager for the ELT: the SCAO module AIT in France, from the beta flat configuration towards the flat and final configurations

MICADO is the designated ELT first light instrument, a near-infrared imager working at the diffraction limit of the telescope thanks to a SCAO and an MCAO mode. Since summer 2024, MICADO is in its AIT phase and all MICADO partners are currently integrating their subsystems. The MICADO SCAO module will follow three successive AIT phases in France: the beta flat configuration, the flat configuration and the final configuration. In this contribution I will first present the progress made in the AIT of the beta flat configuration and its closed loop results. I will then present the performed and on-going tasks for the flat and final configurations (manufacturing, delivery and integration of several SCAO subsystems and pieces of software) and the results obtained so far in the flat configuration. I will then conclude with the expected following steps of the SCAO module AIT in Garching.

astro-ph.IM↗

arXiv2026

SAXO+, the second-stage adaptive optics for SPHERE: NCPA compensation and dark-hole loop with a pyramid wavefront sensor

The SAXO+ upgrade of the VLT/SPHERE adaptive optics system introduces a second-stage near-infrared pyramid wavefront sensor to improve high-contrast imaging, making accurate calibration of non-common path aberrations (NCPAs) essential to fully exploit its performance. This work refines the expected level of NCPAs in SAXO+ and presents the calibration procedures developed for static NCPA compensation and focal-plane dark-hole control. Monte Carlo simulations based on an updated Zemax optical model were used to estimate the NCPA error budget. These simulations are in good agreement with previous measurements on SPHERE and with the assumptions adopted in earlier performance studies. We also propose a calibration strategy that offloads most static aberration correction to the first-stage deformable mirror while preserving the second-stage mirror stroke for high-speed adaptive optics correction. These results validate the expected SAXO+ optical quality and establish the calibration framework required for efficient NCPA compensation and focal-plane wavefront control during future on-sky operations.

astro-ph.IM↗

arXiv2024

Upgrading SPHERE with the second stage AO system SAXO+: frequency-based data-driven controller for adaptive optics

This study introduces a novel frequency-based data-driven controller for adaptive optics, using power spectral density for optimization while ensuring stability criteria. It addresses disturbance rejection, command amplitude constraints and system transfer functions through convex optimization to obtain an optimal control in an infinite input response filter form. Evaluated within the SAXO+ project, it demonstrates efficacy under diverse atmospheric conditions and operational scenarios. The proposed controller is tested in both standard and disentangled adaptive optics schemes, showcasing its adaptability and performance. Experimental validation is conducted using the COMPASS simulation tool, affirming the controller's promise for enhancing adaptive optics systems in real-world applications.

eess.SY↗

arXiv2024

Numerical simulations for the SAXO+ upgrade: Performance analysis of the adaptive optics system

SPHERE, operating at the VLT since 2014, is currently one of the high-contrast instruments with a higher performance. Its adaptive optics system, known as SAXO, will be upgraded to SAXO+, which features the addition of a second stage of adaptive optics. This stage will use a near-infrared pyramid wavefront sensor to record images of fainter exoplanets around redder stars. In this work, we compare the performance of SAXO and SAXO+. We look for the optimal values of the key system parameters of SAXO+ for various science cases and turbulence conditions. We performed numerical simulations using COMPASS, an end-to-end adaptive optics simulation tool. We simulated perfect coronagraph images of an on-axis point source, and we minimized the residual starlight intensity between 3 and 5 $λ/D$ as a performance criterion. The explored parameter space includes science cases, turbulence conditions, and key system parameters. In every science case and turbulence condition, SAXO+ reduces the residual starlight intensity inside the correction zone of the second stage by a factor of ten compared to SAXO. The optimal first stage gain is lower for SAXO+ than for SAXO alone. We quantified the gain in performance of SAXO+ when changing the second stage frequency from 2 kHz to 3 kHz, and we conclude that 2 kHz may be sufficient for most realistic conditions. We give the optimal first stage gain as well as the first and second stage frequencies for every seeing, coherence time, and science case. Finally, we find that a 2 ${λ_{\mathrm{WFS}}}/D$ pyramid modulation radius is a good trade-off between performance and robustness against varying turbulence conditions. This study shows that the future SAXO+ system will outperform the current SAXO system in all studied cases.

astro-ph.IM↗

arXiv2023

SAXO+ upgrade : second stage AO system end-to-end numerical simulations

SAXO+ is a proposed upgrade to SAXO, the AO system of the SPHERE instrument on the ESO Very Large Telescope. It will improve the capabilities of the instrument for the detection and characterization of young giant planets. It includes a second stage adaptive optics system composed of a dedicated near-infrared wavefront sensor and a deformable mirror. This second stage will remove the residual wavefront errors left by the current primary AO loop (SAXO). This paper focuses on the numerical simulations of the second stage (SAXO+) and concludes on the impact of the main AO parameters used to build the design strategy. Using an end-to-end AO simulation tool (COMPASS), we investigate the impact of several parameters on the performance of the AO system. We measure the performance in minimizing the star residuals in the coronagraphic image. The parameters that we study are : the second stage frequency, the photon flux on each WFS, the first stage gain and the DM number of actuators of the second stage. We show that the performance is improved by a factor 10 with respect to the current AO system (SAXO). The optimal second stage frequency is between 1 and 2 kHz under good observing conditions. In a red star case, the best SAXO+ performance is achieved with a low first stage gain of 0.05, which reduces the first stage rejection.

astro-ph.IM↗

arXiv2022

Cascade adaptive optics: contrast performance analysis of a two-stage controller by numerical simulations

The contrast performance of current eXtreme Adaptive Optics (XAO) systems can be improved by adding a second AO correction stage featuring its own wavefront sensor, deformable mirror, and real-time controller. We develop a dynamical model for such a cascade AO (CAO) system with two stages each controlled by a standard integrator, and study its control properties. We study how such a configuration can improve an existing system without modifying the first stage. We analyze the CAO architecture in general and show how part of the disturbance is transferred from low to high temporal frequencies with a nefarious effect of the second stage integrator overshoot, and suggest possible ways to mitigate this. We also carry out numerical simulations of the particular case of a first stage AO using a Shack-Hartmann wavefront sensor and a second stage AO with a smaller deformable mirror running at a higher framerate to reduce temporal error. In this case, we demonstrate that the second stage improves imaging contrast by one order of magnitude and shortens the decorrelation time of atmospheric turbulence speckles by even a greater factor. The results show that CAO presents a promising and relatively simple way to upgrade some existing XAO systems and achieve improved imaging contrasts fostering a large number of science cases including the direct imaging of Exoplanets.

astro-ph.IM↗

arXiv2021

PCS -- A Roadmap for Exoearth Imaging with the ELT

The Planetary Camera and Spectrograph (PCS) for the Extremely Large Telescope (ELT) will be dedicated to detecting and characterising nearby exoplanets with sizes from sub-Neptune to Earth-size in the neighbourhood of the Sun. This goal is achieved by a combination of eXtreme Adaptive Optics (XAO), coronagraphy and spectroscopy. PCS will allow us not only to take images, but also to look for biosignatures such as molecular oxygen in the exoplanets' atmospheres. This article describes the PCS primary science goals, the instrument concept and the research and development activities that will be carried out over the coming years.

astro-ph.IM↗

arXiv2020

Diffraction-limited integral-field spectroscopy for extreme adaptive optics systems with the Multi-Core fiber-fed Integral-Field Unit

Direct imaging instruments have the spatial resolution to resolve exoplanets from their host star. This enables direct characterization of the exoplanets atmosphere, but most direct imaging instruments do not have spectrographs with high enough resolving power for detailed atmospheric characterization. We investigate the use of a single-mode diffraction-limited integral-field unit that is compact and easy to integrate into current and future direct imaging instruments for exoplanet characterization. This achieved by making use of recent progress in photonic manufacturing to create a single-mode fiber-fed image reformatter. The fiber-link is created with 3D printed lenses on top of a single-mode multi-core fiber that feeds an ultrafast laser inscribed photonic chip that reformats the fiber into a pseudo-slit. We then couple it to a first-order spectrograph with a triple stacked volume phase holographic grating for a high efficiency over a large bandwidth. The prototype system has had a successful first-light observing run at the 4.2 meter William Herschel Telescope. The measured on-sky resolving power is between 2500 and 3000, depending on the wavelength. With our observations we show that single-mode integral-field spectroscopy is a viable option for current and future exoplanet imaging instruments.

astro-ph.IM↗