arXiv subjects

Herre S. J. van der Zant

Publications and source records attributed to Herre S. J. van der Zant.

At least 55 records · Page 3Linked to original sources

arXiv2021

Integrating van der Waals materials on paper substrates for electrical and optical applications

Paper holds the promise to replace silicon substrates in applications like internet of things or disposable electronics that require ultra-low-cost electronic components and an environmentally friendly electronic waste management. In the last years, spurred by the abovementioned properties of paper as a substrate and the exceptional electronic, mechanical and optical properties of van der Waals (vdW) materials, many research groups have worked towards the integration of vdW materials-based devices on paper. Recently, a method to deposit a continuous film of densely packed interconnects of vdW materials on paper by simply rubbing the vdW crystals against the rough surface of paper has been presented. This method utilizes the weak interlayer vdW interactions and allows cleaving of the crystals into micro platelets through the abrasion against the paper. Here, we aim to illustrate the general character and the potential of this technique by fabricating films of 39 different vdW materials (including superconductors, semi-metals, semiconductors, and insulators) on standard copier paper. We have thoroughly characterized their optical properties showing their high optical quality: one can easily resolve the absorption band edge of semiconducting vdW materials and even the excitonic features present in some vdW materials with high exciton binding energy. We also measured the electrical resistivity for several vdW materials films on paper finding exceptionally low values, which are in some cases, orders of magnitude lower than those reported for analogous films produced by inkjet printing. We finally demonstrate the fabrication of field-effect devices with vdW materials on paper using the paper substrate as an ionic gate.

cond-mat.mtrl-sci↗

arXiv2021

Integrating superconducting van der Waals materials on paper substrates

Paper has the potential to dramatically reduce the cost of electronic components. In fact, paper is 10 000 times cheaper than crystalline silicon, motivating the research to integrate electronic materials on paper substrates. Among the different electronic materials, van der Waals materials are attracting the interest of the scientific community working on paper-based electronics because of the combination of high electrical performance and mechanical flexibility. Up to now, different methods have been developed to pattern conducting, semiconducting and insulating van der Waals materials on paper but the integration of superconductors remains elusive. Here, the deposition of NbSe2, an illustrative van der Waals superconductor, on standard copy paper is demonstrated. The deposited NbSe2 films on paper display superconducting properties (e.g. observation of Meissner effect and resistance drop to zero-resistance state when cooled down below its critical temperature) similar to those of bulk NbSe2.

cond-mat.supr-con↗

arXiv2021

Study of charge density waves in suspended 2H-TaS2 and 2H-TaSe2 by nanomechanical resonance

The charge density wave (CDW) state in van der Waals systems shows interesting scaling phenomena as the number of layers can significantly affect the CDW transition temperature, $T_{CDW}$. However, it is often difficult to use conventional methods to study the phase transition in these systems due to their small size and sensitivity to degradation. Degradation is an important parameter which has been shown to greatly influence the superconductivity in layered systems. Since the CDW state competes with the onset of superconductivity, it is expected that $T_{CDW}$ will also be affected by the degradation. Here, we probe the CDW phase transition by the mechanical resonances of suspended 2H-TaS2 and 2H-TaSe2 membranes and study the effect of disorder on the CDW state. Pristine flakes show the transition near the reported values of 75 K and 122 K respectively. We then study the effect of degradation on 2H-TaS2 which displays an enhancement of $T_{CDW}$ up to 129 K after degradation in ambient air. Finally, we study a sample with local degradation and observe that multiple phase transitions occur at 87 K, 103 K and 118 K with a hysteresis in temperature in the same membrane. The observed spatial variations in the Raman spectra suggest that variations in crystal structure cause domains with different transition temperatures which could result in the hysteresis. This work shows the potential of using nanomechanical resonance to characterize the CDW in suspended 2D materials and demonstrate that degradation can have a large effect on transition temperatures.

cond-mat.supr-con↗

arXiv2021

Benchmark and application of unsupervised classification approaches for univariate data

Unsupervised machine learning, and in particular data clustering, is a powerful approach for the analysis of datasets and identification of characteristic features occurring throughout a dataset. It is gaining popularity across scientific disciplines and is particularly useful for applications without a priori knowledge of the data structure. Here, we introduce an approach for unsupervised data classification of any dataset consisting of a series of univariate measurements. It is therefore ideally suited for a wide range of measurement types. We apply it to the field of nanoelectronics and spectroscopy to identify meaningful structures in data sets. We also provide guidelines for the estimation of the optimum number of clusters. In addition, we have performed an extensive benchmark of novel and existing machine learning approaches and observe significant performance differences. Careful selection of the feature space construction method and clustering algorithms for a specific measurement type can therefore greatly improve classification accuracies.

cond-mat.mes-hall↗

arXiv2020

Raman Fingerprint of Pressure-Induced Phase Transitions in TiS3 Nanoribbons: Implications for Thermal Measurements under Extreme Stress Conditions

Two-dimensional layered trichalcogenide materials have recently attracted the attention of the scientific community because of its robust mechanical, thermal properties and applications in opto and nanoelectronics devices. We report the pressure dependence of out-of plane Ag Raman modes in high quality few-layers titanium trisulfide (TiS3) nanoribbons grown using a direct solid-gas reaction method and infer their cross-plane thermal expansion coefficient.Both mechanical stability and thermal properties of the TiS3 nanoribbons are elucidated using phonon-spectrum analyses. Raman spectroscopic studies at high pressure (up to 34 GPa) using a diamond anvil cell identify four prominent Ag Raman bands; a band at 557 cm-1 softens under compression, and others at 175, 300, and 370 cm-1 show normal hardening. Anomalies in phonon mode frequencies and excessive broadening in line-width of the soft phonon about ~ 13 GPa are attributed to the possible onset of a reversible structural transition. A complete structural phase transition at 43 GPa is inferred from Ag soft mode frequency (557 cm-1) versus pressure extrapolation curve, consistent with recent reported theoretical predictions. Using the experimental mode Grüneisen parameters i of Raman modes, the cross-plane thermal expansion coefficient Cv of the TiS3 nanoribbons at ambient phase is estimated to be1.32110-6K-1. The observed results are expected to be useful in calibration and performance of next generation nano-electronics and optical devices under extreme stress conditions.

cond-mat.mtrl-sci↗

arXiv2020

Drawing WS2 thermal sensors on paper substrates

Paper based thermoresistive sensors are fabricated by rubbing WS2 powder against a piece of standard copier paper, like the way a pencil is used to write on paper. The abrasion between the layered material and the rough paper surface erodes the material, breaking the weak van der Waals interlayer bonds, yielding a film of interconnected platelets. The resistance of WS2 presents a strong temperature dependence, as expected for a semiconductor material in which charge transport is due to thermally activated carriers. This strong temperature dependence makes the paper supported WS2 devices extremely sensitive to small changes in temperature. This exquisite thermal sensitivity, and their fast response times to sudden temperature changes, is exploited thereby demonstrating the usability of a WS2-on-paper thermal sensor in a respiration monitoring device.

physics.app-ph↗

arXiv2020

Large birefringence and linear dichroism in TiS3 nanosheets

TiS3 nanosheets have proven to be promising candidates for ultrathin optoelectronic devices due to their direct narrow band-gap and the strong light-matter interaction. In addition, the marked in-plane anisotropy of TiS3 is appealing for the fabrication of polarization sensitive optoelectronic devices. Herein, we study the optical contrast of TiS3 nanosheets of variable thickness on SiO2/Si substrates, from which we obtain the complex refractive index in the visible spectrum. We find that TiS3 exhibits very large birefringence, larger than that of well-known strong birefringent materials like TiO2 or calcite, and linear dichroism. These findings are in qualitative agreement with ab initio calculations that suggest an excitonic origin for the birefringence and linear dichroism of the material.

cond-mat.mtrl-sci↗

arXiv2020

Semi-permeability of graphene nanodrums in sucrose solution

Semi-permeable membranes are important elements in water purification and energy generation applications, for which the atomic thickness and strength of graphene can enhance efficiency and permeation rate while maintaining good selectivity. Here, we show that an osmotic pressure difference forms across a suspended graphene membrane as a response to a sucrose concentration difference, providing evidence for its semi-permeability. This osmotic pressure difference is detected via the deflection of the graphene membrane that is measured by atomic force microscopy. Using this technique, the time dependence of this deflection allows us to measure the water permeation rate of a single 3.4 $μ$m diameter graphene membrane. Its value is close to the expected value of a single nanopore in graphene. The method thus allows one to experimentally study the semi-permeability of graphene membranes at the microscale when the leakage rate is miniscule. It can therefore find use in the development of graphene membranes for filtration, and can enable sensors that measure the concentration and composition of solutions.

cond-mat.mes-hall↗

arXiv2020

Nanoelectromechanical Sensors based on Suspended 2D Materials

The unique properties and atomic thickness of two-dimensional (2D) materials enable smaller and better nanoelectromechanical sensors with novel functionalities. During the last decade, many studies have successfully shown the feasibility of using suspended membranes of 2D materials in pressure sensors, microphones, accelerometers, and mass and gas sensors. In this review, we explain the different sensing concepts and give an overview of the relevant material properties, fabrication routes, and device operation principles. Finally, we discuss sensor readout and integration methods and provide comparisons against the state of the art to show both the challenges and promises of 2D material-based nanoelectromechanical sensing.

physics.app-ph↗

arXiv2020

Magnetically-Tuned Kondo Effect in a Molecular Double Quantum Dot: Role of the Anisotropic Exchange

We investigate theoretically and experimentally the singlet-triplet Kondo effect induced by a magnetic field in a molecular junction. Temperature dependent conductance, $G(T)$, is calculated by the numerical renormalization group, showing a strong imprint of the relevant low energy scales, such as the Kondo temperature, exchange and singlet-triplet splitting. We demonstrate the stability of the singlet-triplet Kondo effect against weak spin anisotropy, modeled by an anisotropic exchange. Moderate spin anisotropy manifests itself by lowering the Kondo plateaus, causing the $G(T)$ to deviate from a standard temperature dependence, expected for a spin-half Kondo effect. We propose this scenario as an explanation for anomalous $G(T)$, measured in an organic diradical molecule coupled to gold contacts. We uncover certain new aspects of the singlet-triplet Kondo effect, such as coexistence of spin-polarization on the molecule with Kondo screening and non-perturbative parametric dependence of an effective magnetic field induced by the leads.

cond-mat.mes-hall↗

arXiv2020

Enhancing nonlinear damping by parametric-direct internal resonance

Mechanical sources of nonlinear damping play a central role in modern physics, from solid-state physics to thermodynamics. The microscopic theory of mechanical dissipation [M. I . Dykman, M. A. Krivoglaz, Physica Status Solidi (b) 68, 111 (1975)] suggests that nonlinear damping of a resonant mode can be strongly enhanced when it is coupled to a vibration mode that is close to twice its resonance frequency. To date, no experimental evidence of this enhancement has been realized. In this letter, we experimentally show that nanoresonators driven into parametric-direct internal resonance provide supporting evidence for the microscopic theory of nonlinear dissipation. By regulating the drive level, we tune the parametric resonance of a graphene nanodrum over a range of 40-70 MHz to reach successive two-to-one internal resonances, leading to a nearly two-fold increase of the nonlinear damping. Our study opens up an exciting route towards utilizing modal interactions and parametric resonance to realize resonators with engineered nonlinear dissipation over wide frequency range.

cond-mat.mes-hall↗

arXiv2020

Symmetry breakdown in franckeite: spontaneous strain, rippling and interlayer moiré

Franckeite is a naturally occurring layered mineral with a structure composed of alternating stacks of SnS2-like and PbS-like layers. Although this superlattice is composed of a sequence of isotropic two-dimensional layers, it exhibits a spontaneous rippling that makes the material structurally anisotropic. We demonstrate that this rippling comes hand in hand with an inhomogeneous in-plane strain profile and anisotropic electrical, vibrational and optical properties. We argue that this symmetry breakdown results from a spatial modulation of the van der Waals interaction between layers due to the SnS2-like and PbS-like lattices incommensurability.

cond-mat.mes-hall↗

arXiv2020

MoS$_2$-on-paper optoelectronics: drawing photodetectors with van der Waals semiconductors beyond graphite

We fabricate paper-supported semiconducting devices by rubbing a layered molybdenum disulfide (MoS2) crystal onto a piece of paper, similarly to the action of drawing/writing with a pencil on paper. We show that the abrasion between the MoS2 crystal and the paper substrate efficiently exfoliates the crystals, breaking the weak van der Waals interlayer bonds and leading to the deposition of a film of interconnected MoS2 platelets. Employing this simple method, that can be easily extended to other 2D materials, we fabricate MoS2-on-paper broadband photodectectors with spectral sensitivity from the ultraviolet (UV) to the near-infrared (NIR). We also used these paper-based photodetectors to acquire pictures of objects by mounting the photodetectors in a homebuilt single-pixel camera setup.

physics.app-ph↗

arXiv2020

Tunable Photodetectors via in situ Thermal Conversion of TiS$_3$ to TiO$_2$

In two-dimensional materials research, oxidation is usually considered as a common source for the degradation of electronic and optoelectronic devices or even device failure. However, in some cases a controlled oxidation can open the possibility to widely tune the band structure of 2D materials. In particular, we demonstrate the controlled oxidation of titanium trisulfide (TiS$_3$), a layered semiconductor that has attracted much attention recently thanks to its quasi-1D electronic and optoelectronic properties and its direct bandgap of 1.1 eV. Heating TiS$_3$ in air above 300 °C gradually converts it into TiO$_2$, a semiconductor with a wide bandgap of 3.2 eV with ap-plications in photo-electrochemistry and catalysis. In this work, we investigate the controlled thermal oxidation of individual TiS$_3$ nanoribbons and its influence on the optoelectronic properties of TiS$_3$-based photodetectors. We observe a step-wise change in the cut-off wavelength from its pristine value ~1000 nm to 450 nm after subjecting the TiS$_3$ devices to subsequent thermal treatment cycles. Ab-initio and many-body calculations confirm an increase in the bandgap of titanium oxysulfide (TiO$_{2-x}$S$_x$) when increasing the amount of oxygen and reducing the amount of sulfur.

physics.app-ph↗

arXiv2020

Multi-terminal electronic transport in boron nitride encapsulated TiS$_3$ nanosheets

We have studied electrical transport as a function of carrier density, temperature and bias in multi-terminal devices consisting of hexagonal boron nitride (h-BN) encapsulated titanium trisulfide (TiS$_3$) sheets. Through the encapsulation with h-BN, we observe metallic behavior and high electron mobilities. Below $\sim$60 K an increase in the resistance, and non-linear transport with plateau-like features in the differential resistance are present, in line with the expected charge density wave (CDW) formation. Importantly, the critical temperature and the threshold field of the CDW phase can be controlled through the back-gate.

cond-mat.mtrl-sci↗

arXiv2020

Sensitive capacitive pressure sensors based on graphene membrane arrays

The high flexibility, impermeability and strength of graphene membranes are key properties that can enable the next generation of nanomechanical sensors. However, for capacitive pressure sensors the sensitivity offered by a single suspended graphene membrane is too small to compete with commercial sensors. Here, we realize highly sensitive capacitive pressure sensors consisting of arrays of nearly ten thousand small, freestanding double-layer graphene membranes. We fabricate large arrays of small diameter membranes using a procedure that maintains the superior material and mechanical properties of graphene, even after high-temperature anneals. These sensors are readout using a low cost battery-powered circuit board, with a responsivity of up to 47.8 aF Pa$^{-1}$ mm$^{-2}$, thereby outperforming commercial sensors.

physics.app-ph↗

arXiv2020

A Mechanically Tunable Quantum Dot in a Graphene Break Junction

Graphene quantum dots (QDs) are intensively studied as platforms for the next generation of quantum electronic devices. Fine tuning of the transport properties in monolayer graphene QDs, in particular with respect to the independent modulation of the tunnel barrier transparencies, remains challenging and is typically addressed using electrostatic gating. We investigate charge transport in back-gated graphene mechanical break junctions and reveal Coulomb blockade physics characteristic of a single, high-quality QD when a nanogap is opened in a graphene constriction. By mechanically controlling the distance across the newly-formed graphene nanogap, we achieve reversible tunability of the tunnel coupling to the drain electrode by five orders of magnitude, while keeping the source-QD tunnel coupling constant. These findings indicate that the tunnel coupling asymmetry can be significantly modulated with a mechanical tuning knob and has important implications for the development of future graphene-based devices, including energy converters and quantum calorimeters.

cond-mat.mes-hall↗

arXiv2020

Graphene Effusion-based Gas Sensor

Porous, atomically thin graphene membranes have interesting properties for filtration and sieving applications because they can accommodate small pore sizes, while maintaining high permeability. These membranes are therefore receiving much attention for novel gas and water purification applications. Here we show that the atomic thickness and high resonance frequency of porous graphene membranes enables an effusion based gas sensing method that distinguishes gases based on their molecular mass. Graphene membranes are used to pump gases through nanopores using optothermal forces. By monitoring the time delay between the actuation force and the membrane mechanical motion, the permeation time-constants of various gases are shown to be significantly different. The measured linear relation between the effusion time constant and the square root of the molecular mass provides a method for sensing gases based on their molecular mass. The presented microscopic effusion based gas sensor can provide a small, low-power alternative for large, high-power, mass-spectrometry and optical spectrometry based gas sensing methods.

physics.app-ph↗