arXiv subjects

Hongliang Zhang

Publications and source records attributed to Hongliang Zhang.

At least 127 records · Page 7Linked to original sources

arXiv2020

On Spatial Multiplexing Using Reconfigurable Intelligent Surfaces

We consider an uplink multi-user scenario and investigate the use of reconfigurable intelligent surfaces (RIS) to optimize spatial multiplexing performance when a linear receiver is used. We study two different formulations of the problem, namely maximizing the effective rank and maximizing the minimum singular value of the RIS-augmented channel. We employ gradient-based optimization to solve the two problems and compare the solutions in terms of the sum-rate achievable when a linear receiver is used. Our results show that the proposed criteria can be used to optimize the RIS to obtain effective channels with favorable properties and drastically improve performance even when the propagation through the RIS contributes a small fraction of the received power.

eess.SP↗

arXiv2020

Structural changes of Ti3SiC2 induced by helium irradiation with different doses

In this study, the microstructure changes of Ti3SiC2 MAX phase material induced by helium irradiation and evolution with a sequence of different helium irradiation doses of 5E15, 1E16, 5E16 and 1E17cm-2 at room temperature (RT) were characterized with grazing incidence X-ray diffraction (GIXRD) and Raman spectra analysis. The irradiation damage process of Ti3SiC2 can be roughly divided into three stages according to the level of helium irradiation dose: (1) for a low damage dose, only crystal and damaged Ti3SiC2 exit; (2) at a higher irradiation dose, there is some damaged TiC phase additionally; (3) with a much higher irradiation dose, crystal TiC phase could be found inside the samples as well. Moreover, the 450C 5E16cm-2 helium irradiation on Ti3SiC2 has confirmed that Ti3SiC2 has much higher irradiation tolerance at higher temperature, which implies that Ti3SiC2 could be a potential future structural and fuel coating material working at high temperature environments.

cond-mat.mtrl-sci↗

arXiv2020

Defect behavior and radiation tolerance of MAB phases (MoAlB and Fe2AlB2) with comparison to MAX phases

MAB phases are a new class of layered ternary materials that have already shown a number of outstanding properties. Here, we investigate defect evolution and radiation tolerance of two MAB phases, MoAlB and Fe2AlB2, using a combination of experimental characterization and first-principles calculations. We find that Fe2AlB2 is more tolerant to radiation-induced amorphization than MoAlB, both at 150 °C and at 300 °C. The results can be explained by the fact that the Mo Frenkel pair is unstable in MoAlB and as a result, irradiated MoAlB is expected to have a significant concentration of MoAl antisites, which are difficult to anneal even at 300 °C. We find that the tolerance to radiation-induced amorphization of MAB phases is lower than in MAX phases, but it is comparable to that of SiC. However, MAB phases do not show radiation-induced cracking which is observed in MAX phases under the same irradiation conditions. This study suggests that MAB phases might be a promising class of materials for applications that involve radiation.

cond-mat.mtrl-sci↗

arXiv2020

Helium effects and bubbles formation in irradiated Ti3SiC2

Ti3SiC2 is a potential structural material for nuclear reactor applications. However, He irradiation effects in this material are not well understood, especially at high temperatures. Here, we compare the effects of He irradiation in Ti3SiC2 at room temperature (RT) and at 750 °C. Irradiation at 750 °C was found to lead to extremely elongated He bubbles that are concentrated in the nano-laminate layers of Ti3SiC2, whereas the overall crystal structure of the material remained intact. In contrast, at RT, the layered structure was significantly damaged and highly disordered after irradiation. Our study reveals that at elevated temperatures, the unique structure of Ti3SiC2 can accommodate large amounts of He atoms in the nano-laminate layer, without compromising the structural stability of the material. The structure and the mechanical tests results show that the irradiation induced swelling and hardening at 750 °C are much smaller than those at RT. These results indicate that Ti3SiC2 has an excellent resistance to accumulation of radiation-induced He impurities and that it has a considerable tolerance to irradiation-induced degradation of mechanical properties at high temperatures.

cond-mat.mtrl-sci↗

arXiv2020

Cooperative Internet of UAVs: Distributed Trajectory Design by Multi-agent Deep Reinforcement Learning

Due to the advantages of flexible deployment and extensive coverage, unmanned aerial vehicles (UAVs) have great potential for sensing applications in the next generation of cellular networks, which will give rise to a cellular Internet of UAVs. In this paper, we consider a cellular Internet of UAVs, where the UAVs execute sensing tasks through cooperative sensing and transmission to minimize the age of information (AoI). However, the cooperative sensing and transmission is tightly coupled with the UAVs' trajectories, which makes the trajectory design challenging. To tackle this challenge, we propose a distributed sense-and-send protocol, where the UAVs determine the trajectories by selecting from a discrete set of tasks and a continuous set of locations for sensing and transmission. Based on this protocol, we formulate the trajectory design problem for AoI minimization and propose a compound-action actor-critic (CA2C) algorithm to solve it based on deep reinforcement learning. The CA2C algorithm can learn the optimal policies for actions involving both continuous and discrete variables and is suited for the trajectory design. {Our simulation results show that the CA2C algorithm outperforms four baseline algorithms}. Also, we show that by dividing the tasks, cooperative UAVs can achieve a lower AoI compared to non-cooperative UAVs.

eess.SP↗

arXiv2020

Reconfigurable Intelligent Surface Assisted Device-to-Device Communications

With the evolution of the 5G, 6G and beyond, device-to-device (D2D) communication has been developed as an energy-, and spectrum-efficient solution. In cellular network, D2D links need to share the same spectrum resources with the cellular link. A reconfigurable intelligent surface (RIS) can reconfigure the phase shifts of elements and create favorable beam steering, which can mitigate aggravated interference caused by D2D links. In this paper, we study a RIS-assisted single cell uplink communication network scenario, where the cellular link and multiple D2D links utilize direct propagation and reflecting one-hop propagation. The problem of maximizing the total system rate is formulated by jointly optimizing transmission powers of all links and discrete phase shifts of all elements. The formulated problem is an NP-hard mixed integer non-convex non-linear problem. To obtain practical solutions, we capitalize on alternating maximization and the problem is decomposed into two sub-problems. For the power allocation, the problem is a difference of concave functions (DC) problem, which is solved with the gradient descent method. For the phase shift, a local search algorithm with lower complexity is utilized. Simulation results show that deploying RIS and optimizing the phase shifts have a significant effect on mitigating D2D network interference.

cs.IT↗

arXiv2020

Reconfigurable Intelligent Surfaces for Wireless Communications: Principles, Challenges, and Opportunities

Recently there has been a flurry of research on the use of reconfigurable intelligent surfaces (RIS) in wireless networks to create smart radio environments. In a smart radio environment, surfaces are capable of manipulating the propagation of incident electromagnetic waves in a programmable manner to actively alter the channel realization, which turns the wireless channel into a controllable system block that can be optimized to improve overall system performance. In this article, we provide a tutorial overview of reconfigurable intelligent surfaces (RIS) for wireless communications. We describe the working principles of reconfigurable intelligent surfaces (RIS) and elaborate on different candidate implementations using metasurfaces and reflectarrays. We discuss the channel models suitable for both implementations and examine the feasibility of obtaining accurate channel estimates. Furthermore, we discuss the aspects that differentiate RIS optimization from precoding for traditional MIMO arrays highlighting both the arising challenges and the potential opportunities associated with this emerging technology. Finally, we present numerical results to illustrate the power of an RIS in shaping the key properties of a MIMO channel.

eess.SP↗

arXiv2020

Beyond D2D: Full Dimension UAV-to-Everything Communications in 6G

In this paper, we consider an Internet of unmanned aerial vehicles (UAVs) over cellular networks, where UAVs work as aerial users to collect various sensory data, and send the collected data to their transmission destinations over cellular links. Unlike the terrestrial users in the conventional cellular networks, different UAVs have various communication requirements due to their sensing applications, and a more flexible communication framework is in demand. To tackle this problem, we propose a UAV-to-Everything (U2X) networking, which enables the UAVs to adjust their communication modes full dimensionally according to the requirements of their sensing applications. In this article, we first introduce the concept of U2X communications, and elaborate on its three communication modes. Afterwards, we discuss the key techniques of the U2X communications, including joint sensing and transmission protocol, UAV trajectory design, and radio resource management. A reinforcement learning-based mathematical framework for U2X communications is then proposed. Finally, the extensions of the U2X communications are presented.

eess.SP↗

arXiv2020

UAV-to-Device Underlay Communications: Age of Information Minimization by Multi-agent Deep Reinforcement Learning

In recent years, unmanned aerial vehicles (UAVs) have found numerous sensing applications, which are expected to add billions of dollars to the world economy in the next decade. To further improve the Quality-of-Service (QoS) in such applications, the 3rd Generation Partnership Project (3GPP) has considered the adoption of terrestrial cellular networks to support UAV sensing services, also known as the cellular Internet of UAVs. In this paper, we consider a cellular Internet of UAVs, where the sensory data can be transmitted either to base station (BS) via cellular links, or to mobile devices by underlay UAV-to-Device (U2D) communications. To evaluate the freshness of data, the age of information (AoI) is adopted, in which a lower AoI implies fresher data. Since UAVs' AoIs are determined by their trajectories during sensing and transmission, we investigate the AoI minimization problem for UAVs by designing their trajectories. This problem is a Markov decision problem (MDP) with an infinite state-action space, and thus we utilize multi-agent deep reinforcement learning (DRL) to approximate the state-action space. Then, we propose a multi-UAV trajectory design algorithm to solve this problem. Simulation results show that our algorithm achieves a lower AoI than greedy algorithm and policy gradient algorithm.

eess.SY↗

arXiv2020

Sensing and Communication Tradeoff Design for AoI Minimization in a Cellular Internet of UAVs

In this paper, we consider the cellular Internet of unmanned aerial vehicles (UAVs), where UAVs sense data for multiple tasks and transmit the data to the base station (BS). To quantify the "freshness" of the data at the BS, we bring in the concept of the age of information (AoI). The AoI is determined by the time for UAV sensing and that for UAV transmission, and gives rise to a trade-off within a given period. To minimize the AoI, we formulate a joint sensing time, transmission time, UAV trajectory, and task scheduling optimization problem. To solve this problem, we first propose an iterative algorithm to optimize the sensing time, transmission time, and UAV trajectory for completing a specific task. Afterwards, we design the order in which the UAV performs data updates for multiple sensing tasks. The convergence and complexity of the proposed algorithm, together with the trade-off between UAV sensing and UAV transmission, are analyzed. Simulation results verify the effectiveness of our proposed algorithm.

eess.SP↗

arXiv2020

Reconfigurable Intelligent Surfaces assisted Communications with Limited Phase Shifts: How Many Phase Shifts Are Enough?

Reconfigurable intelligent surface~(RIS) has drawn a great attention worldwide as it can create favorable propagation conditions by controlling the phase shifts of the reflected signals at the surface to enhance the communication quality. However, the practical RIS only has limited phase shifts, which will lead to the performance degradation. In this letter, we evaluate the performance of an uplink RIS assisted communication system by giving an approximation of the achievable data rate, and investigate the effect of limited phase shifts on the data rate. In particular, we derive the required number of phase shifts under a data rate degradation constraint. Numerical results verify our analysis.

cs.IT↗

arXiv2019

Reconfigurable Intelligent Surfaces based RF Sensing: Design, Optimization, and Implementation

Using radio-frequency (RF) sensing techniques for human posture recognition has attracted growing interest due to its advantages of pervasiveness, contact-free observation, and privacy protection. Conventional RF sensing techniques are constrained by their radio environments, which limit the number of transmission channels to carry multi-dimensional information about human postures. Instead of passively adapting to the environment, in this paper, we design an RF sensing system for posture recognition based on reconfigurable intelligent surfaces (RISs). The proposed system can actively customize the environments to provide the desirable propagation properties and diverse transmission channels. However, achieving high recognition accuracy requires the optimization of RIS configuration, which is a challenging problem. To tackle this challenge, we formulate the optimization problem, decompose it into two subproblems and propose algorithms to solve them. Based on the developed algorithms, we implement the system and carry out practical experiments. Both simulation and experimental results verify the effectiveness of the designed algorithms and system. Compared to the random configuration and non-configurable environment cases, the designed system can greatly improve the recognition accuracy.

eess.SP↗

arXiv2019

Reinforcement Learning for a Cellular Internet of UAVs: Protocol Design, Trajectory Control, and Resource Management

Unmanned aerial vehicles (UAVs) can be powerful Internet-of-Things components to execute sensing tasks over the next-generation cellular networks, which are generally referred to as the cellular Internet of UAVs. However, due to the high mobility of UAVs and the shadowing in the air-to-ground channels, UAVs operate in an environment with dynamics and uncertainties. Therefore, UAVs need to improve the quality of service (QoS) of sensing and communication without complete information, which makes reinforcement learning suitable to be employed in the cellular Internet of UAVs. In this article, we propose a distributed sense-and-send protocol to coordinate the UAVs for sensing and transmission. Then, we apply reinforcement learning in the cellular Internet of UAVs to solve key problems such as trajectory control and resource management. Finally, we point out several potential future research directions.

eess.SP↗

arXiv2019

Device-to-Device Communications Underlaying Cellular Networks: To Use Unlicensed Spectrum or Not?

In this paper, we consider device-to-device (D2D) communications as an underlay to the cellular networks over both licensed and unlicensed spectrum, where Long Term Evolution (LTE) users utilize the spectrum orthogonally while D2D users share the spectrum with LTE users. In the system, each LTE and D2D user can access the licensed or unlicensed band for communications. To maximize the total throughput of the system, we leverage stochastic geometry to derive the throughput for each kind of users by modeling the deployment of users as Poisson point processes (PPPs), and investigate the spectrum access problem for these users. Since the problem is NP-hard, we propose a sequential quadratic programming (SQP) based algorithm to obtain the corresponding suboptimal solutions. Theoretically, we evaluate the system performance by analyzing the throughput regions. Simulation results validate the accuracy of the geometric analysis and verify the effectiveness of the proposed algorithm.

eess.SP↗

arXiv2019

Hybrid Beamforming for Reconfigurable Intelligent Surface based Multi-user Communications: Achievable Rates with Limited Discrete Phase Shifts

Reconfigurable intelligent surface (RIS) has drawn considerable attention from the research society recently, which creates favorable propagation conditions by controlling the phase shifts of the reflected waves at the surface, thereby enhancing wireless transmissions. In this paper, we study a downlink multi-user system where the transmission from a multi-antenna base station (BS) to various users is achieved by the RIS reflecting the incident signals of the BS towards the users. Unlike most existing works, we consider the practical case where only a limited number of discrete phase shifts can be realized by the finite-sized RIS. Based on the reflection-dominated one-hop propagation model between the BS and users via the RIS, a hybrid beamforming scheme is proposed and the sum-rate maximization problem is formulated. Specifically, the continuous digital beamforming and discrete RIS-based analog beamforming are performed at the BS and the RIS, respectively, and an iterative algorithm is designed to solve this problem. Both theoretical analysis and numerical validations show that the RIS-based system can achieve a good sum-rate performance by setting a reasonable size of RIS and a small number of discrete phase shifts.

cs.IT↗

arXiv2019

Cooperation Techniques for A Cellular Internet of Unmanned Aerial Vehicles

Unmanned aerial vehicles (UAVs) are powerful Internet-of-Things components to provide sensing and communications in the air due to their advantages in mobility and flexibility. As aerial users, UAVs are envisioned to support various sensing applications in the next generation cellular systems, which have been studied by the Third Generation Partnership Project (3GPP). However, the Quality-of-Services (QoS) of the cellular link between the UAV and the base station may not be guaranteed when UAVs are at the cell edge or experiencing deep fading. In this article, we first introduce the non-cooperative cellular Internet of UAVs. Then we propose a cooperative sense-and-send protocol, in which a UAV can upload sensory data with the help of a UAV relay, to provide a better communication QoS for the sensing tasks. Key techniques including trajectory design and radio resource management that support the cooperative cellular Internet of UAVs are presented in detail. Finally, the extended cooperative cellular Internet of UAVs is discussed for QoS improvement with some open issues, such as massive multiple-input multiple-output systems, millimeter-wave, and cognitive communications.

cs.IT↗

arXiv2019

IoT-U: Cellular Internet-of-Things Networks over Unlicensed Spectrum

In this paper, we consider an uplink cellular Internet-of-Things (IoT) network, where a cellular user (CU) can serve as the mobile data aggregator for a cluster of IoT devices. To be specific, the IoT devices can either transmit the sensory data to the base station (BS) directly by cellular communications, or first aggregate the data to a CU through Machine-to-Machine (M2M) communications before the CU uploads the aggregated data to the BS. To support massive connections, the IoT devices can leverage the unlicensed spectrum for M2M communications, referred to as IoT Unlicensed (IoT-U). Aiming to maximize the number of scheduled IoT devices and meanwhile associate each IoT devices with the right CU or BS with the minimum transmit power, we first introduce a single-stage formulation that captures these objectives simultaneously. To tackle the NP-hard problem efficiently, we decouple the problem into two subproblems, which are solved by successive linear programming and convex optimization techniques, respectively. Simulation results show that the proposed IoT-U scheme can support more IoT devices than that only using the licensed spectrum.

cs.IT↗

arXiv2018

Ultra-dense LEO: Integrating Terrestrial-Satellite Networks into 5G and Beyond for Data Offloading

In this paper, we propose a terrestrial-satellite network (TSN) architecture to integrate the ultra-dense low earth orbit (LEO) networks and the terrestrial networks to achieve efficient data offloading. In TSN, each ground user can access the network over C-band via a macro cell, a traditional small cell, or a LEO-backhauled small cell (LSC). Each LSC is then scheduled to upload the received data via multiple satellites over Ka-band. We aim to maximize the sum data rate and the number of accessed users while satisfying the varying backhaul capacity constraints jointly determined by the LEO satellite based backhaul links. The optimization problem is then decomposed into two closely connected subproblems and solved by our proposed matching algorithms. Simulation results show that the integrated network significantly outperforms the non-integrated ones in terms of the sum data rate. The influence of the traffic load and LEO constellation on the system performance is also discussed.

cs.NI↗