arXiv subjects

Igor Bykov

Publications and source records attributed to Igor Bykov.

7 recordsLinked to original sources

arXiv2026

Spacecraft heat shield study in the DIII-D tokamak

We report a new experimental platform developed at the DIII-D National Fusion Facility to investigate carbon ablation and spallation under extreme heat fluxes relevant to fusion plasma-facing components and high-enthalpy atmospheric entry. Carbon samples were exposed to parallel heat fluxes of $30$--$40~\mathrm{MW\,m^{-2}}$ in the scrape-off layer using two complementary approaches: stationary carbon rods inserted near the divertor strike point and slow-launch carbon pellets injected vertically into the edge and core plasma. Pellets penetrating the core experienced heat fluxes approximately an order of magnitude higher. The conditions reproduce key aspects of the shock-layer environment encountered by the Galileo probe during entry into Jupiter's atmosphere. Fast visible imaging, divertor spectroscopy, infrared thermography, CO$_2$ interferometry, and post-exposure profilometry provided measurements of ablation rates, surface recession, and temperature evolution. Measured mass-loss rates of $(1$--$3)\times10^{-2}~\mathrm{g\,cm^{-2}\,s^{-1}}$ agree with semi-empirical aerospace ablation models, while wedge-shaped rods exhibited greater ablation than cylindrical and concave samples. UEDGE-DUSTT simulations incorporating parallel plasma flows, ${\bf j}\times{\bf B}$ forces, and ablation-cloud shielding reproduce the measured pellet trajectories and ablation timescales. These results establish tokamak plasma as a high-heat-flux environment for validating carbon ablation models and studying material response and impurity dynamics in reactor-relevant divertor plasmas.

physics.plasm-ph↗

arXiv2026

First divertor exposure experiments of a renewable boron pebble aggregate in DIII-D

Boron pebble aggregate was tested for the first time as a high-heat-flux granular plasma-facing material in a tokamak divertor. Exposures of up to $q_{\parallel} = \SI{80}{\MW\per\m\squared}$ incident heat flux were conducted in the DIII-D tokamak. Single protruding rods of pebble aggregate composed of sintered amorphous boron pebbles bound with carbon binder were mounted in the Divertor Material Evaluation System (DiMES) sample holders and exposed to L-mode lower single null (LSN) plasmas. Under these heat loads, significant boron dust emission from the boron spheres was observed, and this dust dominates the divertor boron ionization source. Only about half of the released boron was recovered locally as mm-sized particles; with the rest presumably lost mainly as dust into the plasma and vacuum chamber. Preliminary estimates suggest that the rate of surface recession of $\sim$1 cm/s in the pebble conglomerate within the plasma divertor is consistent with the recession rates observed in laser bench tests subjected to normal-incidence heat loads. Although core performance was not adversely affected by the high boron dust emission, future work will need to improve the boron pebble aggregate design to reduce boron dust emission at high heat loads.

physics.plasm-ph↗

arXiv2023

Investigation of W-SiC compositionally graded films as a divertor material

W-SiC composite material is a promising plasma-facing material candidate alternative to pure W due to the low neutron activation, low impurity radiation, and low tritium diffusivity of SiC while leveraging the high erosion resistance of the W armor. Additionally, W and SiC have high thermomechanical compatibility given their similar thermal expansion rates. The present study addresses the synthesis and performance of compositionally graded W-SiC films fabricated by pulsed-DC magnetron sputtering. Compositional gradients were characterized using transmission electron microscopy (TEM) and energy-dispersive X-ray spectroscopy (EDS), and crystallographic information was obtained using electron diffraction and X-ray diffraction (XRD). Samples were exposed to L-mode deuterium plasma discharges in the DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Post-mortem characterizations were performed using scanning electron microscopy (SEM) and XRD. Electron diffraction and XRD showed that the compositionally graded W-SiC films were composed of polycrystalline W and amorphous SiC with amorphous W+SiC interlayers. No macroscopic delamination or microstructural changes were observed under mild exposure conditions. This study serves as a preliminary examination of W-SiC compositionally graded composites as a potential candidate divertor material in future tokamak devices.

physics.plasm-ph↗

arXiv2023

In-situ coating of silicon-rich films on tokamak plasma-facing components with real-time Si material injection

Experiments have been conducted in the DIII-D tokamak to explore the in-situ growth of silicon-rich layers as a potential technique for real-time replenishment of surface coatings on plasma-facing components (PFCs) during steady-state long-pulse reactor operation. Silicon (Si) pellets of 1 mm diameter were injected into low- and high-confinement (L-mode and H-mode) plasma discharges with densities ranging from $3.9-7.5\times10^{19}$ m$^{-3}$ and input powers ranging from $5.5-9$ MW. The small Si pellets were delivered with the impurity granule injector (IGI) at frequencies ranging from 4-16 Hz corresponding to mass flow rates of $5-19$ mg/s ($1-4.2\times10^{20}$ Si/s) at cumulative amounts of up to 34 mg of Si per five-second discharge. Graphite samples were exposed to the scrape-off layer and private flux region plasmas through the divertor material evaluation system (DiMES) to evaluate the Si deposition on the divertor targets. The Si II emission at the sample correlates with silicon injection and suggests net surface Si-deposition in measurable amounts. Post-mortem analysis showed Si-rich coatings containing silicon oxides, of which SiO$_2$ is the dominant component. No evidence of SiC was found, which is attributed to low divertor surface temperatures. The in-situ and ex-situ analysis found that Si-rich coatings of at least $0.4-1.2$ nm thickness have been deposited at $0.4-0.7$ nm/s. The technique is estimated to coat a surface area of at least 0.94 m$^2$ on the outer divertor. These results demonstrate the potential of using real-time material injection to form Si-enriched layers on divertor PFCs during reactor operation.

physics.plasm-ph↗

arXiv2022

Mitigation of plasma-wall interactions with low-Z powders in DIII-D high confinement plasmas

Experiments with low-Z powder injection in DIII-D high confinement discharges demonstrated increased divertor dissipation and detachment while maintaining good core energy confinement. Lithium (Li), boron (B), and boron nitride (BN) powders were injected in high-confinement mode plasmas ($I_p=$1 MA, $B_t=$2 T, $P_{NB}=$6 MW, $\langle n_e\rangle=3.6-5.0\cdot10^{19}$ m$^{-3}$) into the upper small-angle slot (SAS) divertor for 2-s intervals at constant rates of 3-204 mg/s. The multi-species BN powders at a rate of 54 mg/s showed the most substantial increase in divertor neutral compression by more than an order of magnitude and lasting detachment with minor degradation of the stored magnetic energy $W_{mhd}$ by 5%. Rates of 204 mg/s of boron nitride powder further reduce ELM-fluxes on the divertor but also cause a drop in confinement performance by 24% due to the onset of an $n=2$ tearing mode. The application of powders also showed a substantial improvement of wall conditions manifesting in reduced wall fueling source and intrinsic carbon and oxygen content in response to the cumulative injection of non-recycling materials. The results suggest that low-Z powder injection, including mixed element compounds, is a promising new core-edge compatible technique that simultaneously enables divertor detachment and improves wall conditions during high confinement operation.

physics.plasm-ph↗

arXiv2021

Plasmon localization and giant fields in holographic metasurface for SERS sensors

We present SERS-active metal holographic metasurfaces fabricated from metal periodical nanograting deposited on a dielectric substrate. The metasurface consists of a modulated dielectric, which is covered by a thin silver layer. The metasurface operates as an open plasmon resonator. The theory of plasmons excited in the open resonator formed by a metal nanograting is presented. The large local electromagnetic field is predicted for optical frequencies. The excitation of plasmons is experimentally demonstrated in the metasurface designed on a 4-inch Si wafer. The enhancement of the local electric field results in surface-enhanced Raman scattering (SERS). To investigate the SERS effect, the metasurfaces are covered by molecules of 4-mercaptophenylboronic acid, which form covalent bonds with the silver nanolayer and serve as a proof-of-concept. Finally, we obtain a detection limit of 230 nM for molecules of 4-mercaptophenylboronic acid.

physics.optics↗

arXiv2021

Design and Testing of Dimes Carbon Ablation Rods in the DIII-D Tokamak

We present the design of ATJ graphite rods developed for ablation experiments under high heat flux (up to 50 MW/m2) in the lower divertor of the DIII-D tokamak [1], a magnetic plasma confinement device. This work is motivated by the need to test ablation models relevant to carbon-based thermal shields used in high-speed spacecraft atmospheric entries, where the heat fluxes encountered can be comparable to those achieved in the DIII-D divertor plasma. Several different designs for the flow-facing side of the rod are analyzed, including "sharp nose," "blunt," and "concave". The last shape is studied for its potential to lower heat fluxes at the rod surface by increased radiation from trapped neutrals and reduced parallel plasma pressure. We also analyze the possibility of applying a thin (approximately 30 microns) layer of silicon carbide (SiC) to the exposed part of several carbon ablation rods to benchmark its erosion calculations and lifetime predictions. Such calculations are of interest as SiC represents a promising material for both thermal protection systems (TPS) and a fusion plasma-facing material (PFM). Preliminary results from the DIII-D rod ablation experiments are also discussed.

physics.plasm-ph↗