arXiv subjects

J. Hure

Publications and source records attributed to J. Hure.

16 recordsLinked to original sources

arXiv2020

A micromechanical analysis of intergranular stress corrosion cracking of an irradiated austenitic stainless steel

Irradiation Assisted Stress Corrosion Cracking (IASCC) is a material degradation phenomenon affecting austenitic stainless steels used in nuclear Pressurized Water Reactors (PWR), leading to the initiation and propagation of intergranular cracks. Such phenomenon belongs to the broader class of InterGranular Stress Corrosion Cracking (IGSCC). A micromechanical analysis of IGSCC of an irradiated austenitic stainless steel is performed in this study to assess local cracking conditions. A 304L proton irradiated sample tested in PWR environment and showing intergranular cracking is investigated. Serial sectioning, Electron BackScatter Diffraction (EBSD) and a two-step misalignment procedure are performed to reconstruct the 3D microstructure over an extended volume, to assess statistically cracking criteria. A methodology is also developed to compute Grain Boundary (GB) normal orientations based on the EBSD measurements. The statistical analysis shows that cracking occurs preferentially for GB normals aligned with the mechanical loading axis, but also for low values of the Luster-Morris slip transmission parameter. Micromechanical simulations based on the reconstructed 3D microstructure, FFT-based solver and crystal plasticity constitutive equations modified to account for slip transmission at grain boundaries are finally performed. These simulations rationalize the correlation obtained experimentally into a single stress-based criterion. The actual strengths and weaknesses of such micromechanical approach are discussed.

cond-mat.mtrl-sci↗

arXiv2020

Yield criterion and finite strain behavior of random porous isotropic materials

The mechanical response of isotropic elastoplastic materials containing random distributions of initially spherical voids is investigated computationally based on Fast Fourier Transform simulations. Numerical limit-analysis simulations at constant stress triaxiality allow to determine the yield surfaces, leading in particular to the determination of a Representative Volume Element size for the onset of coalescence / inhomogeneous yielding. Moreover, two different coalescence regimes are observed that differ by the presence of shearing. The yield surfaces are found to be consistent with the combination of two models proposed in the literature, a GTN-type model calibrated for homogeneous yielding of random porous materials and an inhomogeneous yielding model accounting for both coalescence with or without shear. Finite strain simulations performed for different hardening moduli and stress triaxialities under axisymmetric loading conditions confirm the existence of a RVE up to the onset of inhomogeneous yielding. Coalescence strains are found to be significantly smaller for random porous materials than for periodic distribution of voids. A homogenized model is finally proposed that reproduces quantitatively the behavior of isotropic elastoplastic materials containing random distributions of voids under finite strains.

cond-mat.mtrl-sci↗

arXiv2019

A size-dependent ductile fracture model: Constitutive equations, Numerical implementation and Validation

Size effects have been predicted at the micro- or nano-scale for porous ductile materials from Molecular Dynamics, Discrete Dislocation Dynamics and Continuum Mechanics numerical simulations, as a consequence of Geometrically Necessary Dislocations or due to the presence of a void matrix interface. As voids size decreases, higher stresses are needed to deform the material, for a given porosity. However, the majority of the homogenized models for porous materials used in ductile fracture modeling are size-independent, even though micrometric or nanometric voids are commonly observed in structural materials. Based on yield criteria proposed in the literature for nanoporous materials, a size-dependent homogenized model for porous materials is proposed for axisymmetric loading conditions, including void growth and coalescence as well as void shape effects. Numerical implementation of the constitutive equations is detailed. The homogenized model is validated through comparisons to porous unit cells finite element simulations that consider interfacial stresses, consistently with the model used for the derivation of the yield criteria, aiming at modeling an additional hardening at the void matrix interface. Potential improvements of the model are finally discussed with respect to the theoretical derivation of refined yield criteria and evolution laws.

cond-mat.mtrl-sci↗

arXiv2019

Assessing size effects on the deformation of nanovoids in metallic materials

An experimental methodology is developed to evaluate size effects in nanovoids deformation under macroscopic uniaxial stress loading conditions. Quantitative evaluation of voids deformation as a function of voids size shows both a crystallographic effect, albeit small compared to the scatter, and no evidence of size effects for voids diameter larger than 10 nm, while a slight effect is present for smaller voids. Critical assessment of the data in light of theoretical models indicates that these results may be compatible with the presence of a hardened layer at the void/matrix interface, which is illustrated through finite element simulations accounting for surface tension.

cond-mat.mtrl-sci↗

arXiv2018

A coalescence criterion for porous single crystals

Voids can be observed at various scales in ductile materials, frequently of sizes lower than the grain size, leading to porous single crystals materials. Two local deformation modes of porous ductile (single crystals) materials have been identified and referred to as void growth and void coalescence, the latter being characterized by strong interactions between neighboring voids. A simple semi-analytical coalescence criterion for porous single crystals with periodic arrangement of voids is proposed using effective isotropic yield stresses associated with a criterion derived for isotropic materials. An extension of the coalescence criterion is also proposed to account for shear with respect to the coalescence plane. Effective yield stresses are defined using Taylor theory of single crystal deformation, and rely ultimately on the computation of average Taylor factors. Arbitrary sets of slip systems can be considered. The coalescence criterion is assessed through comparisons to numerical limit analysis results performed using a Fast-Fourier-Transform based solver. A good agreement is observed between the proposed criterion and numerical results for various configurations including different sets of slip systems (Face-Centered-Cubic, Hexagonal-Close-Packed), crystal orientations, void shapes and loading conditions. The competition between void growth and void coalescence is described for specific conditions, emphasizing the strong influence of both crystal orientation and void lattice, as well as their interactions.

cond-mat.mtrl-sci↗

arXiv2018

Intergranular normal stress distributions in untextured polycrystalline aggregates

From a general point of view, InterGranular Stress-Corrosion Cracking (IGSCC) results from the interplay between mechanical loading and grain boundaries opening. The former leads to intergranular stresses in polycrystalline aggregates, the latter being either stress-accelerated or stress-induced. This work aims at obtaining intergranular normal stress distributions in uncracked polycrystalline aggregates, which is considered as a key milestone towards IGSCC initiation predictive modelling. Based on the finite element method, numerical simulations have been performed on Voronoi polycrystalline aggregates considering a wide variety of material constitutive equations: crystal elasticity (cubic and hexagonal symmetries) with different anisotropy ratios and crystal plasticity for different sets of slip systems under the assumption of uniform critical resolved shear stress: Face-Centered Cubic (FCC), Body-Centered Cubic (BCC) and Hexagonal Close Packed (HCP) with or without hardening, and for both uniaxial and equibiaxial macroscopic loading conditions. In the elastic regime, a correlation between standard deviations of intergranular normal stress distributions and a universal elastic anisotropy index proposed recently is found and explained through a simple model. For macroscopic strain larger than the yield strain, the evolution of standard deviations with strain is rationalized by accounting only for the macroscopic elastic strain and the standard deviation of Taylor factor. These numerical results associated with physically-based simple models allow to estimate easily intergranular normal stress concentrations, constituting a tool for classifying polycrystalline aggregates according to their potential susceptibility to IGSCC.

cond-mat.mtrl-sci↗

arXiv2018

Void growth and coalescence in irradiated copper under deformation

A decrease of fracture toughness of irradiated materials is usually observed, as reported for austenitic stainless steels in Light Water Reactors (LWRs) or copper alloys for fusion applications. For a wide range of applications (e.g. structural steels irradiated at low homologous temperature), void growth and coalescence fracture mechanism has been shown to be still predominant. As a consequence, a comprehensive study of the effects of irradiation-induced hardening mechanisms on void growth and coalescence in irradiated materials is required. The effects of irradiation on ductile fracture mechanisms - void growth to coalescence - are assessed in this study based on model experiments. Pure copper thin tensile samples have been irradiated with protons up to 0.01 dpa. Micron-scale holes drilled through the thickness of these samples subjected to uniaxial loading conditions allow a detailed description of void growth and coalescence. In this study, experimental data show that physical mechanisms of micron-scale void growth and coalescence are similar between the unirradiated and irradiated copper. However, an acceleration of void growth is observed in the later case, resulting in earlier coalescence, which is consistent with the decrease of fracture toughness reported in irradiated materials. These results are qualitatively reproduced with numerical simulations accounting for irradiation macroscopic hardening and decrease of strain-hardening capability.

cond-mat.mtrl-sci↗

arXiv2017

Anisotropic coalescence criterion for nanoporous materials

Ductile fracture through void growth and coalescence depends significantly on the plastic anisotropy of the material and on void size, as shown by experiments and/or numerical simulations through several studies. Macroscopic (homogenized) yield criteria aiming at modeling nanoporous materials have been proposed only for the growth regime, i.e. non-interacting voids. The aim of this study is thus to provide a yield criterion for nanoporous materials relevant for the coalescence regime, i.e. when plastic flow is localized between voids. Through homogenization and limit analysis, and accounting for interface stresses at the void-matrix interface, analytical coalescence criterion is derived under the following conditions: axisymmetric loading, orthotropic material obeying Hill's plasticity, cylindrical voids in cylindrical unit-cell. Incidentally, an orthotropic extension of the existing isotropic modeling of interface stresses through limit analysis is described and used. The proposed coalescence criterion is then extended to account for combined tension and shear loading conditions. Numerical limit analyses have been performed under specific conditions / materials parameters to get supposedly exact (up to numerical errors) results of coalescence stress. A good agreement between the analytical coalescence criteria derived in this study and numerical results is found for elongated spheroidal voids, making them usable to predict the onset of void coalescence in ductile fracture modeling of nanoporous materials.

cond-mat.mtrl-sci↗

arXiv2016

Theoretical estimates for flat voids coalescence by internal necking

Coalescence of voids by internal necking is in most cases the last microscopic event related to ductile fracture and corresponds to a localized plastic flow between adjacent voids. Macroscopic load associated to the onset of coalescence is classically estimated based on limit analysis. However, a rigorous upper-bound mathematical expression for the limitload required for flat voids coalescence that remains finite for penny-shaped voids/cracks is still unavailable. Therefore, based on limit analysis, theoretical upper-bound estimates - both integral expression and closed-form formula - are obtained for the limit-load of cylindrical flat voids in cylindrical unit-cell subjected to boundary conditions allowing the assessment of coalescence, for axisymmetric stress state. These estimates, leading to finite limit-loads for pennyshaped cracks, are shown to be in very good agreement with numerical limit analysis, for both cylindrical and spheroidal voids. Approximate formula is also given for coalescence under combined tension and shear loading. These coalescence criteria can thus be used to predict onset of coalescence of voids by internal necking in ductile fracture modelling.

cond-mat.mtrl-sci↗

arXiv2016

Intergranular stress distributions in polycrystalline aggregates of irradiated stainless steel

In order to predict InterGranular Stress Corrosion Cracking (IGSCC) of post-irradiated austenitic stainless steel in Light Water Reactor (LWR) environment, reliable predictions of intergranular stresses are required. Finite elements simulations have been performed on realistic polycrystalline aggregate with a recently proposed physically-based crystal plasticity constitutive equations validated for neutron-irradiated austenitic stainless steel. Intergranular normal stress probability density functions are found with respect to plastic strain and irradiation level, for uniaxial loading conditions. In addition, plastic slip activity jumps at grain boundaries are also presented. Intergranular normal stress distributions describe, from a statistical point of view, the potential increase of intergranular stress with respect to the macroscopic stress due to grain-grain interactions. The distributions are shown to be well described by a master curve once rescaled by the macroscopic stress, in the range of irradiation level and strain considered in this study. The upper tail of this master curve is shown to be insensitive to free surface effect, which is relevant for IGSCC

cond-mat.mtrl-sci↗

arXiv2013

Local stresses in the Janssen granular column

We study experimentally the distribution of local stresses in a granular material confined inside a vertical cylinder. We use an image correlation technique to measure the displacement field of the container induced by the forces exerted by the grains on the inner wall. We describe an optimization procedure based on the linear theory of elastic shells to deduce the distribution of these forces from the measured displacement field. They correspond to the stress field of the granular material close to the container's inner wall. We first confirm the validity of Janssen's description for various experiments, including the influence of the bead diameter and the effect of an additional mass on top of the granular column. We then apply this method to determine the stress field during the gravity-driven discharge of a silo through an aperture.

cond-mat.soft↗

arXiv2012

Grabbing water

We introduce a novel technique for grabbing water with a flexible solid. This new passive pipetting mechanism was inspired by floating flowers and relies purely on the coupling of the elasticity of thin plates and the hydrodynamic forces at the liquid interface. Developing a theoretical model has enabled us to design petal-shaped objects with maximum grabbing capacity.

cond-mat.soft↗

arXiv2012

Random blisters on stickers: metrology through defects

Blisters are commonly observed when an adhesive sheet is carelessly deposited on a plate. Although such blisters are usually not desired for practical applications, we show through model experiments on angular blisters how material properties can be deduced from height profile measurements. In particular the typical curvature of the crests is found proportional to an elasto-capillary length that compares the bending stiffness of the sheet with adhesion energy. In addition, the radius of the tip allows to estimate the product of this length with the thickness of the sheet. The relevance of these results to realistic random configurations is finally confirmed.

cond-mat.soft↗

arXiv2012

Capillary buckling of a thin film adhering to a sphere

We present a combined theoretical and experimental study of the buckling of a thin film wrapped around a sphere under the action of capillary forces. A rigid sphere is coated with a wetting liquid, and then wrapped by a thin film into an initially cylindrical shape. The equilibrium of this cylindrical shape is governed by the antagonistic effects of elasticity and capillarity: elasticity tends to keep the film developable while capillarity tends to curve it in both directions so as to maximize the area of contact with the sphere. In the experiments, the contact area between the film and the sphere has cylindrical symmetry when the sphere radius is small, but destabilises to a non-symmetric, wrinkled configuration when the radius is larger than a critical value. We combine the Donnell equations for near-cylindrical shells to include a unilateral constraint with the impenetrable sphere, and the capillary forces acting along a moving edge. A non-linear solution describing the axisymmetric configuration of the film is derived. A linear stability analysis is then presented, which successfully captures the wrinkling instability, the symmetry of the unstable mode, the instability threshold and the critical wavelength. The motion of the free boundary at the edge of the region of contact, which has an effect on the instability, is treated without any approximation.

cond-mat.soft↗

arXiv2012

Stamping and wrinkling of elastic plates

We study the peculiar wrinkling pattern of an elastic plate stamped into a spherical mold. We show that the wavelength of the wrinkles decreases with their amplitude, but reaches a maximum when the amplitude is of the order of the thickness of the plate. The force required for compressing the wrinkled plate presents a maximum independent of the thickness. A model is derived and verified experimentally for a simple one-dimensional case. This model is extended to the initial situation through an effective Young modulus representing the mechanical behavior of wrinkled state. The theoretical predictions are shown to be in good agreement with the experiments. This approach provides a complement to the "tension field theory" developed for wrinkles with unconstrained amplitude.

cond-mat.soft↗

arXiv2011

Wrapping an adhesive sphere with a sheet

We study the adhesion of an elastic sheet on a rigid spherical substrate. Gauss'Theorema Egregium shows that this operation necessarily generates metric distortions (i.e. stretching) as well as bending. As a result, a large variety of contact patterns ranging from simple disks to complex branched shapes are observed as a function of both geometrical and material properties. We describe these different morphologies as a function of two non-dimensional parameters comparing respectively bending and stretching energies to adhesion. A complete configuration diagram is finally proposed.

cond-mat.soft↗