Searcharxiv⌕ Search

arXiv subjects

J. Marin

Publications and source records attributed to J. Marin.

At least 19 recordsLinked to original sources
arXiv2025

Improving radial velocity precision with CARMENES-PLUS:An upgrade of the near-infrared spectrograph cooling system

CARMENES is a dual-channel high-resolution spectrograph at the 3.5 m Calar Alto telescope designed to detect low-mass planets around late-type dwarfs by measuring their radial velocities (RVs). High thermal stability in both the visible (VIS) and near infrared channels is essential to achieve the precision required for these measurements. In particular, stabilising the NIR channel to the millikelvin level, which operates at cryogenic temperatures (140 K), poses significant engineering challenges.The CARMENES-PLUS project was initiated to improve the instruments intrinsic RV precision. In this article, we focus on the thermal stability improvements made to the NIR channels cooling system. The NIR cooling system was originally conceived to operate with a discontinuous flow of cryogenic nitrogen gas. As part of CARMENES-PLUS, this was upgraded to a continuous flow configuration. Additional changes included the installation of an automatic vacuum system, a proportional control valve, and a pressure regulation system. These upgrades were designed to reduce thermal fluctuations and enhance long-term stability. The implemented upgrades significantly improved the intrinsic RV precision of the NIR channel. We quantified this improvement using Fabry Perot calibration spectra, obtaining an intrinsic RV precision of 0.67 ms after the interventions, an improvement of nearly 2 ms . We also assessed the stability of the nightly zero points, finding a reduced scatter of 3.9 ms post upgrade, compared to 6.1 ms before. For a sample of slowly rotating stars (vsin i below 2 kms), the median scatter decreased from 8.8 ms to 6.7 ms after the upgrades. These results demonstrate that the thermal control upgrades introduced in CARMENES PLUS have enhanced the NIR channels RV performance, bringing it closer to the VIS channels stability and reinforcing CARMENES capabilities for exoplanet detection around M dwarfs.

astro-ph.EP↗
arXiv2024

Development of a High-Resolution, High-Dynamic-Range Charge Detector for Ion Beam Monitoring

We present an innovative charge detector with high resolution and wide dynamic range designed to fulfill the requirements of a monitoring system for a high energy ion beam. The detector prototype, constructed using Si photodiodes and a custom readout electronics, underwent extensive testing during HERD and AMS beam tests at CERN SPS facilities. Initial testing showcased the detector's exceptional performance, emphasizing both high resolution and a dynamic range capable of measuring nuclei with atomic numbers ranging from 1 to 80. The prototype's compatibility with fast, quasi real-time data analysis qualifies it as an ideal candidate for online applications. This article presents the results from the testing phase of the prototype, highlighting its capabilities and performance. Ongoing detector development, potential applications, and future developments aimed at enhancing the detector's functionality and versatility are also discussed.

physics.ins-det↗
arXiv2024

Performance assessment of the HERD calorimeter with a photo-diode read-out system for high-energy electron beams

The measurement of cosmic rays at energies exceeding 100 TeV per nucleon is crucial for enhancing the understanding of high-energy particle propagation and acceleration models in the Galaxy. HERD is a space-borne calorimetric experiment that aims to extend the current direct measurements of cosmic rays to unexplored energies. The payload is scheduled to be installed on the Chinese Space Station in 2027. The primary peculiarity of the instrument is its capability to measure particles coming from all directions, with the main detector being a deep, homogeneous, 3D calorimeter. The active elements are read out using two independent systems: one based on wavelength shifter fibers coupled to CMOS cameras, and the other based on photo-diodes read-out with custom front-end electronics. A large calorimeter prototype was tested in 2023 during an extensive beam test campaign at CERN. In this paper, the performance of the calorimeter for high-energy electron beams, as obtained from the photo-diode system data, is presented. The prototype demonstrated excellent performance, e.g., an energy resolution better than 1% for electrons at 250 GeV. A comparison between beam test data and Monte Carlo simulation data is also presented.

physics.ins-det↗
arXiv2024

The UK Submillimetre and Millimetre Astronomy Roadmap 2024

In this Roadmap, we present a vision for the future of submillimetre and millimetre astronomy in the United Kingdom over the next decade and beyond. This Roadmap has been developed in response to the recommendation of the Astronomy Advisory Panel (AAP) of the STFC in the AAP Astronomy Roadmap 2022. In order to develop our stragetic priorities and recommendations, we surveyed the UK submillimetre and millimetre community to determine their key priorities for both the near-term and long-term future of the field. We further performed detailed reviews of UK leadership in submillimetre/millimetre science and instrumentation. Our key strategic priorities are as follows: 1. The UK must be a key partner in the forthcoming AtLAST telescope, for which it is essential that the UK remains a key partner in the JCMT in the intermediate term. 2. The UK must maintain, and if possible enhance, access to ALMA and aim to lead parts of instrument development for ALMA2040. Our strategic priorities complement one another: AtLAST (a 50m single-dish telescope) and an upgraded ALMA (a large configurable interferometric array) would be in synergy, not competition, with one another. Both have identified and are working towards the same overarching science goals, and both are required in order to fully address these goals.

astro-ph.IM↗
arXiv2024

On the relation between magnetic field strength and gas density in the interstellar medium: A multiscale analysis

The magnetic field strength to gas density relation in the interstellar medium is of fundamental importance. We present and compare Bayesian analyses of the B-n relation for two comprehensive observational data sets: a Zeeman data set and 700 observations using the Davis-Chandrasekhar-Fermi (DCF) method. Using a hierarchical Bayesian analysis we present a general, multi-scale broken power-law relation, $B=B_0(n/n_0)^{\alpha}$ , with $\alpha=\alpha_1$ for $n n_0$, and with $B_0$ the field strength at $n_0$. For the Zeeman data we find: $\alpha_1={0.15^{+0.06}_{-0.09}}$ for diffuse gas and $\alpha_2 = {0.53^{+0.09}_{-0.07}}$ for dense gas with $n_0 = 4.00^{+12.7}_{-2.90} \times 10^3$ cm$^{-3}$. For the DCF data we find: $\alpha_1={0.26^{+0.15}_{-0.15}}$ and $\alpha_2={0.77_{-0.15}^{+0.14}}$, with $n_0=13.9^{+10.1}_{-7.30} \times 10^4$ cm$^{-3}$, where the uncertainties give 68\% credible intervals. We perform a similar analysis on nineteen numerical magnetohydrodynamic simulations covering a wide range of physical conditions from protostellar disks to dwarf and Milky Way-like galaxies, completed with the AREPO, Flash, Pencil, and Ramses codes. The resulting exponents depend on several physical factors such as dynamo effects and their time scales, turbulence, and initial seed field strength. \textcolor{red}{We find that the dwarf and Milky Way-like galaxy simulations produce results closest to the observations.

astro-ph.GA↗
arXiv2023

Description and stability of a RPC-based calorimeter in electromagnetic and hadronic shower environments

The CALICE Semi-Digital Hadron Calorimeter technological prototype completed in 2011 is a sampling calorimeter using Glass Resistive Plate Chamber (GRPC) detectors as the active medium. This technology is one of the two options proposed for the hadron calorimeter of the International Large Detector for the International Linear Collider. The prototype was exposed in 2015 to beams of muons, electrons, and pions of different energies at the CERN Super Proton Synchrotron. The use of this technology for future experiments requires a reliable simulation of its response that can predict its performance. GEANT4 combined with a digitization algorithm was used to simulate the prototype. It describes the full path of the signal: showering, gas avalanches, charge induction, and hit triggering. The simulation was tuned using muon tracks and electromagnetic showers for accounting for detector inhomogeneity and tested on hadronic showers collected in the test beam. This publication describes developments of the digitization algorithm. It is used to predict the stability of the detector performance against various changes in the data-taking conditions, including temperature, pressure, magnetic field, GRPC width variations, and gas mixture variations. These predictions are confronted with test beam data and provide an attempt to explain the detector properties. The data-taking conditions such as temperature and potential detector inhomogeneities affect energy density measurements but have a small impact on detector efficiency.

physics.ins-det↗
arXiv2022

Development of the photo-diode subsystem for the HERD calorimeter double-readout

The measurement of cosmic-ray individual spectra provides unique information regarding the origin and propagation of astro-particles. Due to the limited acceptance of current space experiments, protons and nuclei around the "knee" region ($\sim1\ PeV$) can only be observed by ground based experiments. Thanks to an innovative design, the High Energy cosmic-Radiation Detection (HERD) facility will allow direct observation up to this energy region: the instrument is mainly based on a 3D segmented, isotropic and homogeneous calorimeter which properly measures the energy of particles coming from each direction and it will be made of about 7500 LYSO cubic crystals. The read-out of the scintillation light is done with two independent systems: the first one based on wave-length shifting fibers coupled to Intensified scientific CMOS cameras, the second one is made of two photo-diodes with different active areas connected to a custom front-end electronics. This photo-diode system is designed to achieve a huge dynamic range, larger than $10^7$, while having a small power consumption, few mW per channel. Thanks to a good signal-to-noise ratio, the capability of a proper calibration, by using signals of both non-interacting and showering particles, is also guaranteed. In this paper, the current design and the performance obtained by several tests of the photo-diode read-out system are discussed.

physics.ins-det↗
arXiv2022

Energy reconstruction of hadronic showers at the CERN PS and SPS using the Semi-Digital Hadronic Calorimeter

The CALICE Semi-Digital Hadronic CALorimeter (SDHCAL) is the first technological prototype in a family of high-granularity calorimeters developed by the CALICE Collaboration to equip the experiments of future lepton colliders. The SDHCAL is a sampling calorimeter using stainless steel for absorber and Glass Resistive Plate Chambers (GRPC) as a sensitive medium. The GRPC are read out by 1~cm $\times$ 1~cm pickup pads combined to a multi-threshold electronics. The prototype was exposed to hadron beams in both the CERN PS and the SPS beamlines in 2015 allowing the test of the SDHCAL in a large energy range from 3~GeV to 80~GeV. After introducing the method used to select the hadrons of our data and reject the muon and electron contamination, we present the energy reconstruction approach that we apply to the data collected from both beamlines and we discuss the response linearity and the energy resolution of the SDHCAL. The results obtained in the two beamlines confirm the excellent SDHCAL performance observed with the data collected with the same prototype in the SPS beamline in 2012. They also show the stability of the SDHCAL in different beam conditions and different time periods.

hep-ex↗
arXiv2020

Particle Identification Using Boosted Decision Trees in the Semi-Digital Hadronic Calorimeter Prototype

The CALICE Semi-Digital Hadronic CALorimeter (SDHCAL) prototype using Glass Resistive Plate Chambers as a sensitive medium is the first technological prototype of a family of high-granularity calorimeters developed by the CALICE collaboration to equip the experiments of future leptonic colliders. It was exposed to beams of hadrons, electrons and muons several times in the CERN PS and SPS beamlines between 2012 and 2018. We present here a new method of particle identification within the SDHCAL using the Boosted Decision Trees (BDT) method applied to the data collected in 2015. The performance of the method is tested first with Geant4-based simulated events and then on the data collected by the SDHCAL in the energy range between 10 and 80~GeV with 10~GeV energy steps. The BDT method is then used to reject the electrons and muons that contaminate the SPS hadron beams.

physics.ins-det↗
arXiv2018

Hadronic Energy Resolution of a Combined High Granularity Scintillator Calorimeter System

This paper presents results obtained with the combined CALICE Scintillator Electromagnetic Calorimeter, Analogue Hadronic Calorimeter and Tail Catcher & Muon Tracker, three high granularity scintillator-SiPM calorimeter prototypes. The response of the system to pions with momenta between 4 GeV/c and 32 GeV/c is analysed, including the energy response, resolution, and longitudinal shower profiles. The results of a software compensation technique based on weighting according to hit energy are compared to those of a standard linear energy reconstruction. The results are compared to predictions of the GEANT4 physics lists QGSP_BERT_HP and FTFP_BERT_HP.

physics.ins-det↗
arXiv2016

Resistive Plate Chamber Digitization in a Hadronic Shower Environment

The CALICE Semi-Digital Hadron Calorimeter (SDHCAL) technological prototype is a sampling calorimeter using Glass Resistive Plate Chamber detectors with a three-threshold readout as the active medium. This technology is one of the two options proposed for the hadron calorimeter of the International Large Detector for the International Linear Collider. The prototype was exposed to beams of muons, electrons and pions of different energies at the CERN Super Proton Synchrotron. To be able to study the performance of such a calorimeter in future experiments it is important to ensure reliable simulation of its response. In this paper we present our prototype simulation performed with GEANT4 and the digitization procedure achieved with an algorithm called SimDigital. A detailed description of this algorithm is given and the methods to determinate its parameters using muon tracks and electromagnetic showers are explained. The comparison with hadronic shower data shows a good agreement up to 50 GeV. Discrepancies are observed at higher energies. The reasons for these differences are investigated.

physics.ins-det↗
arXiv2016

First results of the CALICE SDHCAL technological prototype

The CALICE Semi-Digital Hadronic Calorimeter (SDHCAL) prototype, built in 2011, was exposed to beams of hadrons, electrons and muons in two short periods in 2012 on two different beam lines of the CERN SPS. The prototype with its 48 active layers, made of Glass Resistive Plate Chambers and their embedded readout electronics, was run in triggerless and power-pulsing mode. The performance of the SDHCAL during the test beam was found to be very satisfactory with an efficiency exceeding 90% for almost all of the 48 active layers. A linear response (within 5%) and a good energy resolution are obtained for a large range of hadronic energies (5-80GeV) by applying appropriate calibration coefficients to the collected data for both the Digital (Binary) and the Semi-Digital (Multi-threshold) modes of the SDHCAL prototype. The Semi-Digital mode shows better performance at energies exceeding 30GeV

physics.ins-det↗
arXiv2016

Hadron shower decomposition in the highly granular CALICE analogue hadron calorimeter

The spatial development of hadronic showers in the CALICE scintillator-steel analogue hadron calorimeter is studied using test beam data collected at CERN and FNAL for single positive pions and protons with initial momenta in the range from 10 to 80 GeV/c. Both longitudinal and radial development of hadron showers are parametrised with two-component functions. The parametrisation is fit to test beam data and simulations using the QGSP_BERT and FTFP_BERT physics lists from Geant4 version 9.6. The parameters extracted from data and simulated samples are compared for the two types of hadrons. The response to pions and the ratio of the non-electromagnetic to the electromagnetic calorimeter response, h/e, are estimated using the extrapolation and decomposition of the longitudinal profiles.

physics.ins-det↗
arXiv2016

DHCAL with Minimal Absorber: Measurements with Positrons

In special tests, the active layers of the CALICE Digital Hadron Calorimeter prototype, the DHCAL, were exposed to low energy particle beams, without being interleaved by absorber plates. The thickness of each layer corresponded approximately to 0.29 radiation lengths or 0.034 nuclear interaction lengths, defined mostly by the copper and steel skins of the detector cassettes. This paper reports on measurements performed with this device in the Fermilab test beam with positrons in the energy range of 1 to 10 GeV. The measurements are compared to simulations based on GEANT4 and a standalone program to emulate the detailed response of the active elements.

physics.ins-det↗
arXiv2015

Shower development of particles with momenta from 15 GeV to 150 GeV in the CALICE scintillator-tungsten hadronic calorimeter

We present a study of showers initiated by electrons, pions, kaons, and protons with momenta from 15 GeV to 150 GeV in the highly granular CALICE scintillator-tungsten analogue hadronic calorimeter. The data were recorded at the CERN Super Proton Synchrotron in 2011. The analysis includes measurements of the calorimeter response to each particle type as well as measurements of the energy resolution and studies of the longitudinal and radial shower development for selected particles. The results are compared to Geant4 simulations (version 9.6.p02). In the study of the energy resolution we include previously published data with beam momenta from 1 GeV to 10 GeV recorded at the CERN Proton Synchrotron in 2010.

physics.ins-det↗
arXiv2015

Pion and proton showers in the CALICE scintillator-steel analogue hadron calorimeter

Showers produced by positive hadrons in the highly granular CALICE scintillator-steel analogue hadron calorimeter were studied. The experimental data were collected at CERN and FNAL for single particles with initial momenta from 10 to 80 GeV/c. The calorimeter response and resolution and spatial characteristics of shower development for proton- and pion-induced showers for test beam data and simulations using Geant4 version 9.6 are compared.

physics.ins-det↗
arXiv2011

Determination of $ππ$ scattering lengths from measurement of $π^+π^-$ atom lifetime

The DIRAC experiment at CERN has achieved a sizeable production of $π^+π^-$ atoms and has significantly improved the precision on its lifetime determination. From a sample of 21227 atomic pairs, a 4% measurement of the S-wave $ππ$ scattering length difference $|a_0-a_2| = (.0.2533^{+0.0080}_{-0.0078}|_\mathrm{stat}.{}^{+0.0078}_{-0.0073}|_\mathrm{syst})M_{π^+}^{-1}$ has been attained, providing an important test of Chiral Perturbation Theory.

hep-ex↗