arXiv subjects

Jan Stake

Publications and source records attributed to Jan Stake.

15 recordsLinked to original sources

arXiv2026

Compact Dual-Polarization Schottky Barrier Diode Receivers for Submillimeter Wave Remote Sensing

Dual-polarization heterodyne receivers operating at 325 GHz, 424 GHz, and 650 GHz at room temperature are presented. Polarimetric measurements are enabled by two orthogonal open-ended E-field probes, co-optimized and integrated with two subharmonic GaAs Schottky-barrier diode mixers. The down-converted signals (IF) are amplified using low-noise InP HEMT amplifiers integrated into the receiver module, along with IF matching networks, dc-bias boards, a shared local oscillator (LO) distribution network, and a single smooth-walled, conical, spline-horn antenna. Maximum cross-polarization isolation of 25 dB, 34 dB, and 25 dB was achieved at 315 GHz, 421 GHz, and 650 GHz, respectively. The measured double-sideband (DSB) receiver noise temperatures are 833 K, 835 K, and 1623 K at 315 GHz, 421 GHz, and 630 GHz, respectively. Stability measurements, with an integration Allan time of more than 10 s, were obtained for all receivers. Overall, the integrated dualpolarization receiver topology achieves excellent sensitivity in a highly compact package, offering an efficient and scalable solution for polarimetric applications in submillimeter-wave remote sensing

physics.ins-det↗

arXiv2024

Impact of E-plane Misalignment on THz Diagonal Horn Antennas

A key challenge in developing terahertz front-ends is achieving high coupling efficiency between the waveguide feed horn and the optical beam. In this paper, we have quantified the alignment requirements for the widely used E-plane split diagonal horn antenna through theoretical analysis, electromagnetic simulation, and experimental validation within the 325-500 GHz frequency range. The results from our analytical models, simulations, and measurements are consistent and shows good agreement. They reveal that even minor geometric asymmetries can cause significant increases in fractional power radiated to the cross-polar component due to amplitude and phase imbalances in the TE10 and TE01 modes. Furthermore, a misalignment of approximately 8% of the wavelength was observed to result in a 3-dB degradation in the optical coupling to a Gaussian beam (Gaussicity) in middle of the waveguide band. These findings highlight the critical importance of precise alignment and feed horn machining for the successful implementation of terahertz front-end systems.

physics.optics↗

arXiv2024

A Broadband Conversion Loss Measurement Technique for Terahertz Harmonic Mixers

This letter presents an experimental characterization technique for assessing the performance of terahertz harmonic mixers across a wide frequency range. The total signal transfer loss of three mixers was measured in both up- and down-conversion configurations, and the conversion loss was determined through the solution of a linear system of equations. The proposed method uses LO signals with a frequency offset to ensure single sideband measurements, thereby eliminating the need for image-reject filters. The three-mixer method was verified by measurements of millimeter-wave mixers, which matched the traditional characterization method using a calibrated source and power meter. Given this successful millimeter-wave demonstration, we characterized three WM-86 Schottky diode x4-harmonic mixers from 2.2 to 3 THz. This technique presents a notable advantage for conducting broadband mixer characterizations, particularly in the terahertz frequency regime which lacks tunable, wide-band sources.

physics.ins-det↗

arXiv2023

A Submillimeter-Wave FMCW Pulse-Doppler Radar to Characterize the Dynamics of Particle Clouds

This work presents a 340-GHz frequency-modulated continuous-wave (FMCW) pulse-Doppler radar. The radar system is based on a transceiver module with about one milli-Watt output power and more than 30-GHz bandwidth. The front-end optics consists of an off-axis parabola fed by a horn antenna from the transceiver unit, resulting in a collimated radar beam. The digital radar waveform generation allows for coherent and arbitrary FMCW pulse waveforms. The performance in terms of sensitivity and resolution (range/cross-range/velocity) is demonstrated, and the system's ability to detect and map single particles (0.1-10 mm diameter), as well as clouds of particles, at a 5-m distance, is presented. A range resolution of 1 cm and a cross-range resolution of a few centimeters (3-dB beam-width) allow for the characterization of the dynamics of particle clouds with a measurement voxel size of a few cubic centimeters. The monitoring of particle dynamics is of interest in several industrial applications, such as in the manufacturing of pharmaceuticals and the control/analysis of fluidized bed combustion reactors.

physics.ins-det↗

arXiv2022

Terahertz Frequency-Domain Sensing Combined with Quantitative Multivariate Analysis for Pharmaceutical Tablet Inspection

Near infrared (NIR) and Raman spectroscopy combined with multivariate analysis are established techniques for the identification and quantification of chemical properties of pharmaceutical tablets like the concentration of active pharmaceutical ingredients (API). However, these techniques suffer from a high sensitivity to particle size variations and are not ideal for the characterization of physical properties of tablets such as tablet density. In this work, we have explored the feasibility of terahertz frequency-domain spectroscopy, with the advantage of low scattering effects, combined with multivariate analysis to quantify API concentration and tablet density. We studied 33 tablets, consisting of Ibuprofen, Mannitol, and a lubricant with API concentration and filler particle size as the design factors. The terahertz signal was measured in transmission mode across the frequency range 750 GHz to 1.5 THz using a vector network analyzer, frequency extenders, horn antennas, and four off-axis parabolic mirrors. The attenuation spectral data were pre-processed and orthogonal partial least square (OPLS) regression was applied to the spectral data to obtain quantitative prediction models for API concentration and tablet density. The performance of the models was assessed using test sets. While a fair model was obtained for API concentration, a high-quality model was demonstrated for tablet density. The coefficient of determination for the calibration set was 0.97 for tablet density and 0.98 for API concentration, while the relative prediction errors for the test set were 0.7% and 6%for tablet density and API concentration models, respectively.

physics.app-ph↗

arXiv2022

A corrugated planar-Goubau-line termination for terahertz waves

The planar Goubau line is a promising low-loss metal waveguide for terahertz interconnects. To enable advanced system architectures and multi-port measurements based on planar Goubau lines, there is a strong need for broadband impedance-matched loads, which can be used to absorb the energy and minimize standing waves in a system. In this work, we propose a matched load for planar Goubau lines based on an exponentially-tapered corrugated line, gradually increasing conductor losses while maintaining small reflections. The corrugation density is high enough to increase conductor losses without requiring an auxiliary low-conductivity material, simplifying the fabrication process. A 400-$\mu$m long planar Goubau line load was fabricated on a 10-$\mu$m thick silicon substrate suspended in the air. Electromagnetic simulations of the load show excellent agreement with calibrated reflection measurements in the frequency range 0.5 THz - 1.1 THz. Above the cut-off frequency of around 580 GHz, the measured reflections are much less than -19 dB, below the noise floor of the characterization setup.

physics.app-ph↗

arXiv2022

Sub-millimetre wave range-Doppler radar as a diagnostic tool for gas-solids systems -- solids concentration measurements

Current non-intrusive measurement techniques for characterising the solids flow in gas-solids suspensions are limited by the low temporal or low spatial resolution of the sample volume, or in the case of optical methods, by a short range of sight. In this work, a sub-millimetre wave range-Doppler radar is developed and validated for non-intrusive sensing of solids concentrations in a gas-solids particle system with known characteristics. The radar system combines favourable features, such as the ability to see through at optical frequencies opaque materials, to measure the local solids velocity and the reflected radar power with a spatial resolution of a few cubic centimetres over distances of a few metres. This paper introduces a method to relate the received radar signal power to the solids volumetric concentrations (cv) of different particulate materials. The experimental set-up provides a steady stream of free-falling solids that consist of glass spheres, bronze spheres or natural sand grains with known particle size distributions and with particle diameters in the range of 50-300 $\mu$m. Thus, the values of cv found using the radar measurements are validated using the values of cv retrieved from closure of the mass balance derived from the measured mass flow rate of the solids stream and the solids velocity. The results show that the radar system provides reliable measurements of cv, with a mean relative error of approximately 25% for all the tested materials, particle sizes and mass flow rates, yielding values of cv ranging from 0.2x10$^{-4}$ m$^{3}$/ m$^{3}$ up to 40x10$^{-4}$ m$^{3}$/ m$^{3}$ and solids velocities within the range of 0-4.5 m/s. This demonstrates the ability of the radar technology to diagnose the solids flow in gas-solids suspensions using a unique combination of penetration length, accuracy, and spatial and velocity resolution.

physics.app-ph↗

arXiv2022

Capacitively-coupled resonators for terahertz planar-Goubau-line filters

Low-loss planar Goubau lines show promising potential for terahertz applications. However, a single-wire waveguide exhibits less design freedom than standard multi-conductor lines, which is a significant constraint for realizing standard components. Existing filters for planar Goubau line lack clear design procedures preventing the synthesis of an arbitrary filter response. In this work, we present a design for a bandpass/bandstop filter for planar Goubau line by periodically loading the line with capacitively coupled {\lambda}/2 resonators, which can be easily tuned by changing their electrical length. The filter's working principle is explained by a proposed transmission-line model. We designed and fabricated a passband filter centered at 0.9 THz on a 10-{\mu}m silicon-membrane substrate and compared measurement results between 0.5 THz and 1.1 THz to electromagnetic simulations, showing excellent agreement in both S11 and S21. The measured passband has an insertion loss of 7 dB and a 3-dB bandwidth of 31 %. Overall, the proposed filter design has good performance while having a simple design procedure.

physics.app-ph↗

arXiv2021

Terahertz Frequency Domain Sensing for Fast Porosity Measurement of Pharmaceutical Tablets

Porosity is an important property of pharmaceutical tablets since it may affect tablet disintegration, dissolution, and bio-availability. It is, therefore, essential to establish non-destructive, fast, and compact techniques to assess porosity, in-situ, during the manufacturing process. In this paper, the terahertz frequency-domain (THz-FD) technique was explored as a fast, non-destructive, and sensitive technique for porosity measurement of pharmaceutical tablets. We studied a sample set of 69 tablets with different design factors, such as particle size of the active pharmaceutical ingredient (API), Ibuprofen, particle size of the filler, Mannitol, API concentration, and compaction force. The signal transmitted through each tablet was measured across the frequency range 500-750 GHz using a vector network analyzer combined with a quasi-optical set-up consisting of four off-axis parabolic mirrors to guide and focus the beam. We first extracted the effective refractive index of each tablet from the measured complex transmission coefficients and then translated it to porosity, using an empirical linear relation between effective refractive index and tablet density. The results show that the THz-FD technique was highly sensitive to the variations of the design factors, showing that filler particle size and compaction force had a significant impact on the effective refractive index of the tablets and, consequently, porosity. Moreover, the fragmentation behaviour of particles was observed by THz porosity measurements and was verified with scanning electron microscopy of the cross-section of tablets. In conclusion, the THz-FD technique, based on electronic solutions, allows for fast, sensitive, and non-destructive porosity measurement that opens for compact instrument systems capable of in-situ sensing in tablet manufacturing.

physics.app-ph↗

arXiv2021

Terahertz rectennas on flexible substrates based on one-dimensional metal-insulator-graphene diodes

Flexible energy harvesting devices fabricated in scalable thin-film processes are important components in the field of wearable electronics and the Internet of Things. We present a flexible rectenna based on a one-dimensional junction metal-insulator-graphene diode, which offers low-noise power detection at terahertz (THz) frequencies. The rectennas are fabricated on a flexible polyimide film in a scalable process by photolithography using graphene grown by chemical vapor deposition. A one-dimensional junction area reduces the junction capacitance and enables operation in the D-band (110 - 170 GHz). The rectenna on polyimide shows a maximum voltage responsivity of 80 V/W at 167 GHz in free space measurements and minimum noise equivalent power of 80 pW/$\sqrt{\text{Hz}}$.

physics.app-ph↗

arXiv2021

Graphene FET on diamond for high-frequency electronics

Transistors operating at high frequencies are the basic building blocks of millimeter-wave communication and sensor systems. The high velocity and mobility of carriers in graphene can open way for ultra-fast group IV transistors with similar or even better performance than can be achieved with III-V based semiconductors. However, the progress of high-speed graphene transistors has been hampered due to fabrication issues, influence of adjacent materials, and self-heating effects. Here, we report a graphene field-effect transistor (FET) on a diamond substrate, with a $f_{max}$ up to 54 GHz for a gate length of 500 nm. The high thermal conductivity of diamond provides an efficient heat-sink, and its relatively high optical-phonon energy improves saturation velocity of carriers in the graphene channel. Moreover, we show that graphene FETs on diamond, with different gate lengths, exhibit excellent scaling behavior. These results indicate that graphene FETs on diamond technology can reach sub-terahertz frequency performance.

cond-mat.mes-hall↗

arXiv2021

A 3.5-THz, x6-Harmonic, Single-Ended Schottky Diode Mixer for Frequency Stabilization of Quantum-Cascade Lasers

Efficient and compact frequency converters are essential for frequency stabilization of terahertz sources. In this paper, we present a 3.5-THz, x6-harmonic, integrated Schottky diode mixer operating at room temperature. The designed frequency converter is based on a single-ended, planar Schottky diode with a sub-micron anode contact area defined on a suspended 2-$\mu$m ultra-thin GaAs substrate. The dc-grounded anode pad was combined with the radio frequency E-plane probe, which resulted in an electrically compact circuit. At 200 MHz intermediate frequency, a mixer conversion loss of about 59 dB is measured and resulting in a 40 dB signal-to-noise ratio for phase locking 3.5-THz quantum-cascade laser. Using a quasi-static diode model combined with electromagnetic simulations, good agreement with the measured results was obtained. Harmonic frequency converters without the need of cryogenic cooling will help in the realization of highly sensitive space and air-borne heterodyne receivers.

physics.ins-det↗

arXiv2020

On-Chip Characterization of High-Loss Liquids between 750 GHz and 1100 GHz

Terahertz spectroscopy is a promising tool for analyzing the picosecond dynamics of biomolecules, which is influenced by surrounding water molecules. However, water causes extreme losses to terahertz signals, preventing sensitive measurements at this frequency range. Here, we present sensitive on-chip terahertz spectroscopy of highly lossy aqueous solutions using a vector network analyzer, contact probes, and a coplanar waveguide with a 0.1 mm wide microfluidic channel. The complex permittivities of various deionized water/isopropyl alcohol concentration are extracted from a known reference measurement across the frequency range 750-1100 GHz and agrees well with literature data. The results prove the presented method as a high-sensitive approach for on-chip terahertz spectroscopy of high-loss liquids, capable of resolving the permittivity of water.

physics.app-ph↗

arXiv2020

Thermoelectric graphene photodetectors with sub-nanosecond response times at Terahertz frequencies

Ultrafast and sensitive (noise equivalent power <1 nWHz-1/2) light-detection in the Terahertz (THz) frequency range (0.1-10 THz) and at room-temperature is key for applications such as time-resolved THz spectroscopy of gases, complex molecules and cold samples, imaging, metrology, ultra-high-speed data communications, coherent control of quantum systems, quantum optics and for capturing snapshots of ultrafast dynamics, in materials and devices, at the nanoscale. Here, we report room-temperature THz nano-receivers exploiting antenna-coupled graphene field effect transistors integrated with lithographically-patterned high-bandwidth (~100 GHz) chips, operating with a combination of high speed (hundreds ps response time) and high sensitivity (noise equivalent power <120 pWHz-1/2) at 3.4 THz. Remarkably, this is achieved with various antenna and transistor architectures (single-gate, dual-gate), whose operation frequency can be extended over the whole 0.1-10 THz range, thus paving the way for the design of ultrafast graphene arrays in the far infrared, opening concrete perspective for targeting the aforementioned applications.

physics.app-ph↗

arXiv2019

Does carrier velocity saturation help to enhance fmax in graphene field-effect transistors?

It has been argued that current saturation in graphene field-effect transistors (GFETs) is needed to get the highest possible maximum oscillation frequency (fmax). This paper numerically investigates whether velocity saturation can help to get better current saturation and if that correlates with enhanced fmax. For such a purpose, we used a drift-diffusion simulator that includes several factors that influence output conductance, especially at short channel lengths and-or large drain bias: short-channel electrostatics, saturation velocity, graphene-dielectric interface traps, and self-heating effects. As a testbed for our investigation, we analyzed fabricated GFETs with high extrinsin cutoff frequency fT,x (34 GHz) and fmax (37 GHz). Our simulations allow for a microscopic (local) analysis of the channel parameteres such as carrier concentration, drift and saturation velocities. For biases far away from the Dirac voltage, where the channel behaves as unipolar, we confirmed that the higher is the drift velocity, as close as possible to the saturation velocity, the greater fmax is. However, the largest fmax is recorded at biases near the crossover between unipolar and bipolar behavior, where it does not hold that the highest drift velocity maximizes fmax. In fact, the position and magnitude of the largest fmax depend on the complex interplay between the carrier concentration and total velocity which, in turn, are impacted by the self-heating. Importantly, this effect was found to severely limit radio-frequency performance, reducing the maximum fmax from around 60 to 40 GHz.

physics.app-ph↗