arXiv subjects

Jaume Gazquez

Publications and source records attributed to Jaume Gazquez.

13 recordsLinked to original sources

arXiv2025

Detecting Linear Dichroism with Atomic Resolution

X-ray linear dichroism has been pivotal for probing electronic anisotropies, but its inherent limited spatial resolution precludes atomic-scale investigations of orbital polarization. Here we introduce a versatile electron linear dichroism methodology in scanning transmission electron microscopy that overcomes these constraints. By exploiting momentum-transfer-dependent electron energy-loss spectroscopy with an atomic-sized probe, we directly visualize orbital occupation at individual atomic columns in real space. Using strained La0.7Sr0.3MnO3 thin films as a model system, we resolve the Mn-3d eg orbital polarization with sub-angstrom precision. We show that compressive strain stabilizes 3z2-r2 occupation while tensile strain favors x2-y2. These results validate our approach against established X-ray measurements while achieving the ultimate single atomic-column sensitivity. We further demonstrate two optimized signal extraction protocols that adapt to experimental constraints without compromising sensitivity. This generalizable platform opens unprecedented opportunities to study symmetry-breaking phenomena at individual defects, interfaces, and in quantum materials where atomic-scale electronic anisotropy governs emergent functionality.

cond-mat.mtrl-sci↗

arXiv2024

Stoichiometric control of electron mobility and 2D superconductivity at LaAlO$_3$-SrTiO$_3$ interfaces

SrTiO$_3$-based conducting interfaces, which exhibit coexistence of gate-tunable 2D superconductivity and strong Rashba spin-orbit coupling (RSOC), are candidates to host topological superconductive phases. Yet, superconductivity is usually in the dirty limit, which tends to suppress nonconventional pairing and therefore challenges these expectations. Here we report on LaAlO$_3$/SrTiO$_3$ (LAO/STO) interfaces with remarkably large mobility and mean free paths comparable to the superconducting coherence length, approaching the clean limit for superconductivity. We further show that the carrier density, mobility, and formation of the superconducting condensate are controlled by the fine-tuning of La/Al chemical ratio in the LAO film. Interestingly, we find a region in the superconducting phase diagram where the critical temperature is not suppressed below the Lifshitz transition, at odds with previous experimental investigations. These findings point out the relevance of achieving a clean-limit regime to enhance the observation of unconventional pairing mechanisms in these systems

cond-mat.supr-con↗

arXiv2023

Formation of Mn-rich interfacial phases in Co2FexMn1-xSi thin films

We report the formation of Mn-rich regions at the interface of Co2FexMn1-xSi thin films grown on GaAs substrates by molecular beam epitaxy (MBE). Scanning transmission electron microscopy (STEM) with electron energy loss (EEL) spectrum imaging reveals that each interfacial region: (1) is 1-2 nm wide, (2) occurs irrespective of the Fe/Mn composition ratio and in both Co-rich and Co-poor films, and (3) displaces both Co and Fe indiscriminately. We also observe a Mn-depleted region in each film directly above each Mn-rich interfacial layer, roughly 3 nm in width in the x = 0 and x = 0.3 films, and 1 nm in the x = 0.7 (less Mn) film. We posit that growth energetics favor Mn diffusion to the interface even when there is no significant Ga interdiffusion into the epitaxial film. Element-specific X-ray magnetic circular dichroism (XMCD) measurements show larger Co, Fe, and Mn orbital to spin magnetic moment ratios compared to bulk values across the Co2FexMn1-xSi compositional range. The values lie between reported values for pure bulk and nanostructured Co, Fe, and Mn materials, corroborating the non-uniform, layered nature of the material on the nanoscale. Finally, SQUID magnetometry demonstrates that the films deviate from the Slater-Pauling rule for uniform films of both the expected and the measured composition. The results inform a need for care and increased scrutiny when forming Mn-based magnetic thin films on III-V semiconductors like GaAs, particularly when films are on the order of 5 nm or when interface composition is critical to spin transport or other device applications.

cond-mat.mtrl-sci↗

arXiv2021

Polarization and resistive switching in epitaxial 2 nm Hf$_{0.5}$Zr$_{0.5}$O$_2$ tunnel junctions

In the quest for reliable and power-efficient memristive devices, ferroelectric tunnel junctions are being investigated as potential candidates. CMOS-compatible ferroelectric hafnium oxides are at the forefront. However, in epitaxial tunnel devices with thicknesses around ${\approx}$ 4 - 6 nm, the relatively high tunnel energy barrier produces a large resistance that challenges their implementation. Here, we show that ferroelectric and electroresistive switching can be observed in ultrathin 2 nm epitaxial Hf$_{0.5}$Zr$_{0.5}$O$_2$ (HZO) tunnel junctions in large area capacitors (${\approx} 300μm^2$). We observe that the resistance area product is reduced to about 160 $Ω{\cdot}$cm$^2$ and 65 $Ω{\cdot}$cm$^2$ for OFF and ON resistance states, respectively. These values are two orders of magnitude smaller than those obtained in equivalent 5 nm HZO tunnel devices while preserving a similar OFF/ON resistance ratio (210 ${\%}$). The devices show memristive and spike-timing-dependent plasticity (STDP) behavior and good retention. Electroresistance and ferroelectric loops closely coincide, signaling ferroelectric switching as a driving mechanism for resistance change.

physics.app-ph↗

arXiv2021

Critical Effect of Bottom Electrode on Ferroelectricity of Epitaxial Hf0.5Zr0.5O2 Thin Films

Epitaxial orthorhombic Hf0.5Zr0.5O2 (HZO) films on La0.67Sr0.33MnO3 (LSMO) electrodes show robust ferroelectricity, with high polarization, endurance and retention. However, no similar results have been achieved using other perovskite electrodes so far. Here, LSMO and other perovskite electrodes are compared. A small amount of orthorhombic phase and low polarization is found in HZO films grown on La-doped BaSnO3 and Nb-doped SrTiO3, while null amounts of orthorhombic phase and polarization are detected in films on LaNiO3 and SrRuO3. The critical effect of the electrode on the stabilized phases is not consequence of differences in the electrode lattice parameter. The interface is critical, and engineering the HZO bottom interface on just a few monolayers of LSMO permits the stabilization of the orthorhombic phase. Furthermore, while the specific divalent ion (Sr or Ca) in the manganite is not relevant, reducing the La content causes a severe reduction of the amount of orthorhombic phase and the ferroelectric polarization in the HZO film.

cond-mat.mtrl-sci↗

arXiv2020

Crystal Engineering and Ferroelectricity at the Nanoscale in Epitaxial 1D Manganese Oxide on Silicon

Ferroelectric oxides have attracted much attention due to their wide range of applications, especially in electronic devices such as nonvolatile memories and tunnel junctions. As a result, the monolithic integration of these materials into silicon technology and its nanostructuration to develop alternative cost-effective processes are among the central points in current technology. In this work, we used a chemical route to obtain nanowire thin films of a novel Sr1+δMn8O16 (SMO) hollandite-type manganese oxide on silicon. Scanning transmission electron microscopy combined with crystallographic computing reveals a crystal structure comprising hollandite and pyrolusite units sharing the edges of their MnO6 octahedra, resulting in three types of tunnels arranged along the c axis, where ordering of the Sr atoms produces a natural symmetry breaking. The novel structure gives rise to a ferroelectricity and piezoelectricity, as revealed by local Direct Piezoelectric Force Microscopy measurements, which confirmed the ferroelectric nature of SMO nanowire thin films at room temperature and showed a piezoelectric coefficient d33 value of 22,6 pC/N. Moreover, we proved that flexible vertical SMO nanowires can be harvested and converted into electric output energy through the piezoelectric effect, showing an excellent deformability and high interface recombination. This work indicates the possibility of engineering the integration of 1D manganese oxides on silicon, a step which precedes the production of microelectronic devices.

cond-mat.mtrl-sci↗

arXiv2019

Rotational polarization nanotopologies in BaTiO3/SrTiO3 superlattices

Ferroelectrics are characterized by domain structures as are other ferroics. At the nanoscale though, ferroelectrics may exhibit non-trivial or exotic polarization configurations under proper electrostatic and elastic conditions. These polar states may possess emerging properties not present in the bulk compounds and are promising for technological applications. Here, the observation of rotational polarization topologies at the nanoscale by means of aberration-corrected scanning transmission electron microscopy is reported in BaTiO3/SrTiO3 superlattices grown on cubic SrTiO3(001). The transition from a highly homogeneous polarization state to the formation of rotational nanodomains has been achieved by controlling the superlattice period while maintaining compressive clamping of the superlattice to the cubic SrTiO3 substrate. The nanodomains revealed in BaTiO3 prove that its nominal tetragonal structure also allows rotational polar textures.

cond-mat.mtrl-sci↗

arXiv2019

Engineering Ferroelectric Hf0.5Zr0.5O2 Thin Films by Epitaxial Stress

The critical impact of epitaxial stress on the stabilization of the ferroelectric orthorhombic phase of hafnia is proved. Epitaxial bilayers of Hf0.5Zr0.5O2 and La0.67Sr0.33MnO3 electrodes were grown on a set of single crystalline oxide 001-oriented, cubic or pseudocubic setting, substrates with lattice parameter in the 3.71 - 4.21 A range. The lattice strain of the La0.67Sr0.33MnO3 electrode, determined by the lattice mismatch with the substrate, is critical in the stabilization of the orthorhombic phase of Hf0.5Zr0.5O2. On La0.67Sr0.33MnO3 electrodes tensile strained most of the Hf0.5Zr0.5O2 film is orthorhombic, whereas the monoclinic phase is favored when La0.67Sr0.33MnO3 is relaxed or compressively strained. Therefore, the Hf0.5Zr0.5O2 films on TbScO3 and GdScO3 substrates present substantially enhanced ferroelectric polarization in comparison to films on other substrates, including the commonly used SrTiO3. The capability of having epitaxial doped HfO2 films with controlled phase and polarization is of major interest for a better understanding of the ferroelectric properties and paves the way for fabrication of ferroelectric devices based on nanometric HfO2 films.

cond-mat.mtrl-sci↗

arXiv2018

Magnetoresistance in Hybrid Pt/CoFe2O4 Bilayers Controlled by Competing Spin Accumulation and Interfacial Chemical Reconstruction

Pure spin currents hold promises for an energy-friendlier spintronics. They can be generated by a flow of charge along a non-magnetic metal having a large spin-orbit coupling. It produces a spin accumulation at its surfaces, controllable by the magnetization of an adjacent ferromagnetic layer. Paramagnetic metals typically used are close to a ferromagnetic instability and thus magnetic proximity effects can contribute to the observed angular-dependent magnetoresistance (ADMR). As interface phenomena govern the spin conductance across the metal/ferromagnetic-insulator heterostructures, unraveling these distinct contributions is pivotal to full understanding of spin current conductance. We report here x-ray absorption and magnetic circular dichroism (XMCD) at Pt-M and (Co,Fe)-L absorption edges and atomically-resolved energy loss electron spectroscopy (EELS) data of Pt/CoFe2O4 bilayers where CoFe2O4 layers have been capped by Pt grown at different temperatures. It turns out that the ADMR differs dramatically, being either dominated by spin Hall magnetoresistance (SMR) associated to spin Hall effect or anisotropic magnetoresistance (AMR). The XMCD and EELS data indicate that the Pt layer grown at room temperature does not display any magnetic moment, whereas when grown at higher temperature it is magnetic due to interfacial Pt-(Co,Fe) alloying. These results allow disentangling spin accumulation from interfacial chemical reconstructions and for tailoring the angular dependent magnetoresistance.

cond-mat.mtrl-sci↗

arXiv2017

Evaluation of microstructure and mechanical property variations in AlxCoCrFeNi high entropy alloys produced by a high-throughput laser deposition method

Twenty-one distinct AlxCoCrFeNi alloys were rapidly prepared by laser alloying an equiatomic CoCrFeNi substrate with Al powder to create an alloy library ranging x=0.15-1.32. Variations in crystal structure, microstructure and mechanical properties were investigated using X-ray diffraction, scanning electron microscopy, scanning transmission electron microscopy and nanoindentation. With increasing Al content, the crystal structure transitioned from a disordered FCC to a mixture of disordered BCC and ordered B2 structures. While the onset of BCC/B2 formation was consistent with previously reported cast alloys, the FCC structure was observed at larger Al contents in the laser processed materials, resulting in a wider two phase regime. The FCC phase was primarily confined to the BCC/B2 grain boundaries at these high Al contents. The nanoindentation modulus and hardness of the FCC phase increased with Al content, while the properties of the BCC/B2 structure were insensitive to composition. The structure and mechanical properties of the laser-processed alloys were surprisingly consistent with reported results for cast alloys, demonstrating the feasibility of applying this high-throughput methodology to multicomponent alloy design.

cond-mat.mtrl-sci↗

arXiv2015

Conducting interfaces between amorphous oxide layers and SrTiO3(110) and SrTiO3(111)

Interfaces between (110) and (111)SrTiO3 (STO) single crystalline substrates and amorphous oxide layers, LaAlO3 (a-LAO), Y:ZrO2 (a-YSZ), and SrTiO3 (a-STO) become conducting above a critical thickness tc. Here we show that tc for a-LAO is not depending on the substrate orientation, i.e. tc (a-LAO/(110)STO) ~ tc(a-LAO/(111)STO) interfaces, whereas it strongly depends on the composition of the amorphous oxide: tc(a-LAO/(110)STO) < tc(a-YSZ/(110)STO) < tc(a-STO/(110)STO). It is concluded that the formation of oxygen vacancies in amorphous-type interfaces is mainly determined by the oxygen affinity of the deposited metal ions, rather than orientational-dependent enthalpy vacancy formation and diffusion. Scanning transmission microscopy characterization of amorphous and crystalline LAO/STO(110) interfaces shows much higher amount of oxygen vacancies in the former, providing experimental evidence of the distinct mechanism of conduction in these interfaces.

cond-mat.mtrl-sci↗

arXiv2014

Multiferroic Iron Oxide Thin Films at Room-Temperature

In spite of being highly relevant for the development of a new generation of information storage devices, not many single-phase materials displaying magnetic and ferroelectric orders above room temperature are known. Moreover, these uncommon materials typically display insignificant values of the remanent moment in one of the ferroic orders or are complex multicomponent oxides which will be very challenging to integrate in devices. Here we report on the strategy to stabilize the metastable epsilon-Fe2O3 in thin film form, and we show that besides its already known ferrimagnetic nature, the films are also ferroelectric at 300 K with a remanent polarization of 1 microC/cm2. The film polarization shows long retention times and can be switched under small applied voltages. These characteristics make of epsilon-Fe2O3 the first single-ion transition-metal oxide which is ferro(ferri)magnetic and ferroelectric at room temperature. The simple composition of this new multiferroic oxide and the discovery of a robust path for its thin film growth may boost the exploitation of epsilon-Fe2O3 in novel devices.

cond-mat.mtrl-sci↗

arXiv2010

Conducting interfaces between band insulating oxides: the LaGaO3/SrTiO3

We show that the growth of the heterostructure LaGaO3/SrTiO3 yields the formation of a highly conductive interface. Our samples were carefully analyzed by high resolution electron microscopy, in order to assess their crystal perfection and to evaluate the abruptness of the interface. Their carrier density and sheet resistance are compared to the case of LaAlO3/SrTiO3 and a superconducting transition is found. The results open the route to widening the field of polar-non polar interfaces, pose some phenomenological constrains to their underlying physics and highlight the chance of tailoring their properties for future applications by adopting suitable polar materials.

cond-mat.mtrl-sci↗