arXiv subjects

Jaw-Shen Tsai

Publications and source records attributed to Jaw-Shen Tsai.

34 records · Page 2Linked to original sources

arXiv2021

Quasiparticle tunneling and 1/f charge noise in ultrastrongly coupled superconducting qubit and resonator

We report an experimentally observed anomalous doubly split spectrum and its split-width fluctuation in an ultrastrongly coupled superconducting qubit and resonator. From an analysis of Rabimodel and circuit model Hamiltonians, we found that the doubly split spectrum and split-width fluctuation are caused by discrete charge hops due to quasiparticle tunnelings and a continuous background charge fluctuation in islands of a flux qubit. During 70 hours in the spectrum measurement, split width fluctuates but the middle frequency of the split is constant. This result indicates that quasiparticles in our device seem mainly tunnel one particular junction. The background offsetcharge obtained from split width has the 1/f noise characteristic.

quant-ph↗

arXiv2021

Ultrastrong tunable coupler between superconducting LC resonators

We investigate the ultrastrong tunable coupler for coupling of superconducting resonators. Obtained coupling constant exceeds 1 GHz, and the wide range tunability is achieved both antiferromagnetics and ferromagnetics from $-1086$ MHz to 604 MHz. The ultrastrong coupler is composed of rf-SQUID and dc-SQUID as tunable junctions, which connected to resonators via shared aluminum thin film meander lines enabling such a huge coupling constant. The spectrum of the coupler obviously shows the breaking of the rotating wave approximation, and our circuit model treating the Josephson junction as a tunable inductance reproduces the experimental results well. The ultrastrong coupler is expected to be utilized in quantum annealing circuits and/or NISQ devices with dense connections between qubits.

quant-ph↗

arXiv2021

Magnetic-free traveling-wave nonreciprocal superconducting microwave components

We propose a design to realize integrated broadband nonreciprocal microwave isolators and circulators using superconducting circuit elements without any magnetic materials. To obtain a broadband response, we develop a waveguide-based design by temporal modulations. The corresponding compact traveling-wave structure is implemented with integrated superconducting composite right-/left-handed transmission lines. The calculations show that the bandwidth of 580 MHz can be realized over a nonreciprocal isolation of 20 dB in reflections. Such on-chip isolators and circulators are useful for cryogenic integrated microwave connections and measurements, such as protecting qubits from the amplified reflected signal in multiplexed readout.

quant-ph↗

arXiv2019

Superconducting Quantum Annealing Architecture with LC Resonators

We propose a novel architecture for superconducting circuits to improve the efficiency of a quantum annealing system. To increase the capability of a circuit, it is desirable for a qubit to be coupled not only with adjacent qubits but also with other qubits located far away. We introduce a circuit that uses a lumped element resonator coupled each with one qubit. The resonator-qubit pairs are coupled by rf-superconducting quantum interference device (SQUID) based couplers. These pairs make a large quantum system for quantum annealer. This system could prepare the problem Hamiltonian and tune the parameters for quantum annealing procedure.

quant-ph↗

arXiv2016

Interplay of the inverse proximity effect and magnetic field in out-of-equilibrium single-electron devices

The magnetic field is shown to affect significantly non-equilibrium quasiparticle (QP) distributions under conditions of inverse proximity effect on the remarkable example of a single-electron hybrid turnstile. This effect suppresses the gap in the superconducting leads in the vicinity of turnstile junctions with a Coulomb blockaded island, thus, trapping hot QPs in this region. Applied magnetic field creates additional QP traps in the form of vortices or regions with reduced superconducting gap in the leads resulting in release of QPs away from junctions. We present clear experimental evidence of such interplay of the inverse proximity effect and a magnetic field revealing itself in the superconducting gap enhancement in a magnetic field as well as in significant improvement of the turnstile characteristics. The observed interplay of the inverse proximity effect and external magnetic field, and its theoretical explanation in the context of QP overheating are important for various superconducting and hybrid nanoelectronic devices, which find applications in quantum computation, photon detection and quantum metrology.

cond-mat.mes-hall↗

arXiv2016

Doping-Induced Alterations in Electronic Structure of Copper Oxide Superconductors and a New Horizon for Higher Tc materials

By paying special attention to the fact that the doped holes induce deformation of CuO6 octahedrons (or CuO5 pyramids) in cuprate superconductors, we develop a non-rigid band theory treating doping-induced alterations of energy-band structures in copper oxide superconductors. Thanks to this theory, we obtain a complete picture of the doping-induced alteration in the electronic structure of La2CuO4, from the spin-disordered insulating phase to the metallic phase. We conclude that the Fermi surface structure of this cuprate in the underdoped region consists of Fermi pockets in the antinodal region and Fermi arcs in the nodal region, and thus that the origin of a so-called pseudogap is closely related to the existence of Fermi pockets. Moreover, we show that the carriers on the Fermi pockets contribute to the phonon mechanism in d-wave superconductivity. Finally, we discuss how one will be able to find higher Tc materials, based on the conclusions mentioned above.

cond-mat.supr-con↗

arXiv2016

Single microwave-photon detector using an artificial $Λ$-type three-level system

Single photon detection is a requisite technique in quantum-optics experiments in both the optical and the microwave domains. However, the energy of microwave quanta are four to five orders of magnitude less than their optical counterpart, making the efficient detection of single microwave photons extremely challenging. Here, we demonstrate the detection of a single microwave photon propagating through a waveguide. The detector is implemented with an "impedance-matched" artificial $Λ$ system comprising the dressed states of a driven superconducting qubit coupled to a microwave resonator. We attain a single-photon detection efficiency of $0.66 \pm 0.06$ with a reset time of $\sim 400$~ns. This detector can be exploited for various applications in quantum sensing, quantum communication and quantum information processing.

quant-ph↗

arXiv2014

Flux qubit noise spectroscopy using Rabi oscillations under strong driving conditions

We infer the high-frequency flux noise spectrum in a superconducting flux qubit by studying the decay of Rabi oscillations under strong driving conditions. The large anharmonicity of the qubit and its strong inductive coupling to a microwave line enabled high-amplitude driving without causing significant additional decoherence. Rabi frequencies up to 1.7 GHz were achieved, approaching the qubit's level splitting of 4.8 GHz, a regime where the rotating-wave approximation breaks down as a model for the driven dynamics. The spectral density of flux noise observed in the wide frequency range decreases with increasing frequency up to 300 MHz, where the spectral density is not very far from the extrapolation of the 1/f spectrum obtained from the free-induction-decay measurements. We discuss a possible origin of the flux noise due to surface electron spins.

cond-mat.supr-con↗

arXiv2012

Spectral Analysis and Identification of Noises in Quantum Systems

In quantum information processing, knowledge of the noise in the system is crucial for high-precision manipulation and tomography of coherent quantum operations. Existing strategies for identifying this noise require the use of additional quantum devices or control pulses. We present a noise-identification method directly based on the system's non-Markovian response of an ensemble measurement to the noise. The noise spectrum is identified by reversing the response relationship in the frequency domain. For illustration, the method is applied to superconducting charge qubits, but it is equally applicable to any type of qubits. We find that the identification strategy recovers the well-known Fermi's golden rule under the lowest-order perturbation approximation, which corresponds to the Markovian limit when the measurement time is much longer than the noise correlation time. Beyond such approximation, it is possible to further improve the precision at the so-called optimal point by incorporating the transient response data in the non-Markovian regime. This method is verified with experimental data from coherent oscillations in a superconducting charge qubit.

quant-ph↗

arXiv2012

Spectroscopy of low-frequency noise and its temperature dependence in a superconducting qubit

We report a direct measurement of the low-frequency noise spectrum in a superconducting flux qubit. Our method uses the noise sensitivity of a free-induction Ramsey interference experiment, comprising free evolution in the presence of noise for a fixed period of time followed by single-shot qubit-state measurement. Repeating this procedure enables Fourier-transform noise spectroscopy with access to frequencies up to the achievable repetition rate, a regime relevant to dephasing in ensemble-averaged time-domain measurements such as Ramsey interferometry. Rotating the qubit's quantization axis allows us to measure two types of noise: effective flux noise and effective critical-current or charge noise. For both noise sources, we observe that the very same 1/f-type power laws measured at considerably higher frequencies (0.2-20 MHz) are consistent with the noise in the 0.01-100-Hz range measured here. We find no evidence of temperature dependence of the noises over 65-200 mK, and also no evidence of time-domain correlations between the two noises. These methods and results are pertinent to the dephasing of all superconducting qubits.

cond-mat.supr-con↗

arXiv2011

Dynamical decoupling and noise spectroscopy with a superconducting flux qubit

The characterization and mitigation of decoherence in natural and artificial two-level systems (qubits) is fundamental to quantum information science and its applications. Decoherence of a quantum superposition state arises from the interaction between the constituent system and the uncontrolled degrees of freedom in its environment. Within the standard Bloch-Redfield picture of two-level system dynamics, qubit decoherence is characterized by two rates: a longitudinal relaxation rate Gamma1 due to the exchange of energy with the environment, and a transverse relaxation rate Gamma2 = Gamma1/2 + Gamma_phi which contains the pure dephasing rate Gamma_phi. Irreversible energy relaxation can only be mitigated by reducing the amount of environmental noise, reducing the qubit's internal sensitivity to that noise, or through multi-qubit encoding and error correction protocols (which already presume ultra-low error rates). In contrast, dephasing is in principle reversible and can be refocused dynamically through the application of coherent control pulse methods. In this work we demonstrate how dynamical-decoupling techniques can moderate the dephasing effects of low-frequency noise on a superconducting qubit with energy-relaxation time T1 = 1/Gamma1 = 12 us. Using the CPMG sequence with up to 200 pi-pulses, we demonstrate a 50-fold improvement in the transverse relaxation time T2 over its baseline value. We observe relaxation-limited times T2(CPMG) = 23 us = 2 T1 resulting from CPMG-mediated Gaussian pure-dephasing times in apparent excess of 100 us. We leverage the filtering property of this sequence in conjunction with Rabi and energy relaxation measurements to facilitate the spectroscopy and reconstruction of the environmental noise power spectral density.

cond-mat.supr-con↗

arXiv2010

Correlated flux noise and decoherence in two inductively coupled flux qubits

We have studied decoherence in a system where two Josephson-junction flux qubits share a part of their superconducting loops and are inductively coupled. By tuning the flux bias condition, we control the sensitivities of the energy levels to flux noises in each qubit. The dephasing rate of the first excited state is enhanced or suppressed depending on the amplitudes and the signs of the sensitivities. We have quantified the $1/f$ flux noises and their correlations and found that the dominant contribution is by local fluctuations.

cond-mat.supr-con↗

arXiv2009

Film-thickness dependence of 10 GHz Nb coplanar-waveguide resonators

We have studied Nb lambda/2 coplanar-waveguide (CPW) resonators whose resonant frequencies are 10-11 GHz. The resonators have different film thicknesses, t=0.05, 0.1, 0.2, and 0.3 um. We measured at low temperatures, T=0.02-5 K, one of the scattering-matrix element, S_21, which is the transmission coefficient from one port to the other. At the base temperatures, T=0.02-0.03 K, the resonators are overcoupled to the input/output microwave lines, and the loaded quality factors are on the order of 10^3. The resonant frequency has a considerably larger film-thickness dependence compared to the predictions by circuit simulators which calculate the inductance of CPW taking into account L_g only, where L_g is the usual magnetic inductance determined by the CPW geometry. By fitting a theoretical S_21 vs. frequency curve to the experimental data, we determined for each film thickness, the phase velocity of the CPW with an accuracy better than 0.1%. The large film-thickness dependence must be due to the kinetic inductance L_k of the CPW center conductor. We also measured S_21 as a function of temperature up to T=4-5 K, and confirmed that both thickness and temperature dependence are consistent with the theoretical prediction for L_k.

cond-mat.supr-con↗

arXiv2009

Power-dependent internal loss in Josephson bifurcation amplifiers

We have studied nonlinear superconducting resonators: lambda/2 coplanar-waveguide (CPW) resonators with Josephson junctions (JJs) placed in the middle and lambda/4 CPW resonators terminated by JJs, which can be used for the qubit readout as "bifurcation amplifiers." The nonlinearity of the resonators arises from the Josephson junctions, and because of the nonlinearity, the resonators with appropriate parameters are expected to show a hysteretic response to the frequency sweep, or "bifurcation," when they are driven with a sufficiently large power. We designed and fabricated resonators whose resonant frequencies were around 10 GHz. We characterized the resonators at low temperatures, T<0.05 K, and confirmed that they indeed exhibited hysteresis. The sizes of the hysteresis, however, are sometimes considerably smaller than the predictions based on the loaded quality factor in the weak drive regime. When the discrepancy appears, it is mostly explained by taking into account the internal loss, which often increases in our resonators with increasing drive power in the relevant power range. As a possible origin of the power-dependent loss, the quasiparticle channel of conductance of the JJs is discussed.

cond-mat.supr-con↗

arXiv2006

Tunable coupling scheme for flux qubits at the optimal point

We discuss a practical design for tunably coupling a pair of flux qubits via the quantum inductance of a third high-frequency qubit. The design is particularly well suited for realizing a recently proposed microwave-induced parametric coupling scheme. This is attractive because the qubits can always remain at their optimal points. Furthermore, we will show that the resulting coupling also has an optimal point where it is insensitive to low-frequency flux noise. This is an important feature for the coherence of coupled qubits. The presented scheme is an experimentally realistic way of carrying out two-qubit gates and should be easily extended to multiqubit systems.

cond-mat.mes-hall↗

arXiv2004

Circuit with small-capacitance high-quality Nb Josephson junctions

We have developed a fabrication process for nanoscale tunnel junctions which includes focused-ion-beam etching from different directions. By applying the process to a Nb/(Al-)Al_2O_3/Nb trilayer, we have fabricated a Nb single-electron transistor (SET), and characterized the SET at low temperatures, T=0.04-40 K. The superconducting gap energy and the transition temperature of the Nb SET agree with the bulk values, which suggests high quality Nb junctions. The single-electron charging energy of the SET is estimated to be larger than 1 K.

cond-mat.mes-hall↗