arXiv subjects

Jeanette Hussong

Publications and source records attributed to Jeanette Hussong.

13 recordsLinked to original sources

arXiv2026

Species Transport Driven by Droplet Impact in Wavy Thin Films

Droplet impact on thin liquid films is commonly studied on quiescent surfaces, although practical systems often involve residual capillary waves generated by preceding droplets. This study examines how such traveling waves modify impact dynamics and mixing. Controlled surface disturbances were produced using an acoustic excitation system that replicated droplet-induced waves, and a two-color laser-induced fluorescence method was implemented to obtain simultaneous measurements of film thickness and dye concentration. Impacts on wavy films deviated markedly from quiescent conditions. Rim evolution, cavity collapse, and jet formation became asymmetric, governed by the phase of the wave relative to the impact. These behaviors were linked to local variations in film depth, which redirected cavity retraction and the associated mixing flow. Reconstructed concentration fields confirmed that droplet liquid is displaced according to these depth gradients, producing asymmetric mixing at moderate Weber numbers. A dimensionless asymmetry index quantified the dependence on wave amplitude, phase, and distance from the acoustic wave generator. At higher Weber numbers, inertial mixing attenuated these effects, and the dynamics approached those of static films.

physics.flu-dyn↗

arXiv2026

Two-Color LIF investigation of mixing during droplet impact onto a thin liquid film

A two-color laser-induced fluorescence (2C-LIF) technique is presented for investigating droplet impact on thin liquid films, enabling simultaneous, spatially and temporally resolved measurements of film thickness and scalar concentration. The method is applied to water droplets impacting thin liquid films over a range of Reynolds numbers, Weber numbers and dimensionless film thicknesses, providing direct access to early-time mixing processes during impact. To quantify scalar transport within the liquid film, the reconstructed concentration fields are evaluated using a coefficient-of-variaton (CV) approach, providing a quantitative measure of mixture homogeneity. This enables identification of the transition from inertia-dominated convective transport to diffusion-controlled mixing. Based on this analysis, an empirical correlation describing the evolution of CV as a function of Reynolds number and film thickness is formulated. Finally, the applicability of the 2C-LIF method is demonstrated for binary ethanol-water films, where additional transport mechanisms influence and modify the mixing dynamics.

physics.flu-dyn↗

arXiv2026

Droplet impact on surfactant-laden thin liquid films: Vortex ring dynamics

Droplet impact on surfactant-laden thin liquid films is investigated experimentally with emphasis on vortex ring dynamics. Bottom- and side-view imaging reveal that increasing surfactant concentration progressively stabilize vortex rings, suppress azimuthal instabilities and promote concentric mixing patterns. A regime map is established in terms of film thickness, Reynolds number, and surface-tension ratio, yielding an empirical instability threshold. Shadowgraphy observations suggest that Marangoni stresses modify early capillary-wave dynamics, potentially altering vortex ring formation and delaying instability onset. These findings clarify the link between interfacial stresses, vortex ring dynamics, and mixing patterns in thin-film droplet impact.

physics.flu-dyn↗

arXiv2025

On the vortex ring formation and mixing in thin films upon droplet impact

When a droplet impacts a liquid film, a vortex ring form and govern momentum and species transport. We experimentally investigate vortex ring formation, propagation and instability during droplet impact onto liquid films, with particular emphasis on vortex ring-wall interactions. Particle image velocimetry and laser-induced fluorescence are used to study the effects of Reynolds number Re, Weber number We and dimensionless film thickness δover ranges Re \leq 3900, We \leq 61 and 0.09 \leq δ\leq 1.35. As film thickness decreases, a transition from a single axisymmetric vortex ring to azimuthally unstable, multi-vortex structures is observed. A regime map in Re-δspace is constructed, showing that vortex ring instabilities occur at lower Re for thinner films, while no instabilities are detected for thick films up to the highest Re studied. The azimuthal wave number increases with Re and decreases with δ. Thinner films exhibit faster decay of primary vortex ring circulation due to wall interactions, accompanied by the formation of secondary vortex ring at lower Re. An empirical model is proposed to predict the temporal evolution of total vortex ring circulation, accounting for both generation and decay.

physics.flu-dyn↗

arXiv2025

Drop impact on a heated pre-wetted wall: deposition-on-crater splash regime

The impact of a liquid drop with high Reynolds and Weber numbers on a wet solid surface typically results in the emergence, rising, and expansion of a corona-like thin jet. This phenomenon is explained by the propagation of a kinematic discontinuity within the wall film. Conventional theories suggest that the corona-forming liquid jet comprises material from the impacting drop and wall film. In this study, the impact of a drop on a wall film is observed using a high-speed video system. Simultaneously, the distribution of the contact temperature at the substrate surface is measured with a high-speed infrared system. The results reveal that heat transfer predominantly occurs within the thin thermal boundary layers in the drop and substrate. Moreover, our experiments show that under our specific conditions, the drop deposits at the base of the crater while only the wall film produces the corona and splashes. Correspondingly, the secondary drops consist only of the heated material of the wall film. This regime has not been previously reported in the literature. The validated models for the diameter of the cold spot, the characteristic time, and the contact temperature developed in this study can be potentially useful for reliable modeling of spray cooling.

physics.flu-dyn↗

arXiv2025

Dewetting Fingering Instability in Capillary Suspensions: Role of Particles and Liquid Bridges

This study investigates the fingering instability that forms during stretching of capillary suspensions with and without added nanoparticles. The dewetting process is observed using a transparent lifted Hele-Shaw cell. The liquid bridge is stretched under constant acceleration, and the resulting instability patterns are recorded using two high-speed cameras. Finger-like structures, characteristic of the Saffman-Taylor instability are observed. The total length of the dendrites and the intersecting number of branches are quantified. We reveal the roles of microparticles, nanoparticles, and the secondary liquid during the fingering instability. The addition of microparticles to pure liquid enhanced finger length due to increased particle interactions and nucleation sites for bubbles. The addition of secondary fluid reduces fingering length by forming a strong interparticle network. Incorporation of nanoparticles induces an early onset of cavitation and enhances fingering instability. However, nanoparticles make the capillary suspensions' overall microstructure more homogeneous, reduce the sample variation in fingering patterns, and promote the even distribution of gel on both slides during splitting. These findings highlight the complex interactions governing dewetting in capillary (nano)suspensions. This knowledge has potential applications in microfluidics, 3D printing, and thin-film coatings, where controlling dewetting is crucial.

cond-mat.soft↗

arXiv2025

Thermal Finite-Element Model of an Electric Machine Cooled by a Spray

The need for higher power density in electrical machines require better cooling strategies. Spray cooling is a very promising and relatively simple technology to apply, but involves extremely complicated physics. In this paper, a quasi-3D thermal finite-element model of a stator winding is created, by extrusion of a 2D cross-sectional finite-element model along the winding direction. The possible effects of spray cooling are simulated as a heat flux using an impedance boundary condition at the surface of the winding overhang. The results confirm the beneficial performance of spray cooling. The model indicates that spray cooling may allow a ten times larger power density than for standard air- or water-cooled machines.

cs.CE↗

arXiv2023

Studying Macro- and Mesoscopic Wetting Dynamics of a Spreading Oil Droplet Using Multiple Wavelength Interferometry

In this study we present an interferometric technique based on multiple wavelengths to capture the transient free surface contour of nanoliter drops spreading on a wettable surface, in particular close to the three-phase contact line. Various data analysis procedures are evaluated in terms of error and noise sensitivity. The technique allows an unambiguous determination of the local liquid film thickness for optical path differences up to $Δs \approx 3.19\,\mathrm{μm}$ without the need of a known reference height. Film thicknesses as low as $0.1\,\mathrm{μm}$ can be measured with the present optical configuration. The entire three-dimensional droplet shape is investigated for different capillary numbers, allowing also reliable measurements of the time-resolved contact angle.

physics.flu-dyn↗

arXiv2020

On the micro PIV accuracy and reliability utilizing suspension particles of large, non-Gaussian particle image

Optical investigations on the dynamics of dense suspensions are challenging due to reduced optical accessibility. Furthermore, the suspension particle image size can strongly deviate from the optimal particle image size for PIV measurements. Optical accessibility can be achieved by refractive index matching of surface labelled suspension particles. This results in particle images that are transparent in the particle image center, but fluoresce at the particle image rim, resulting in ring-shaped particle images. In the present study the influence of particle image size of such ring-shaped particle images is compared with Gaussian and plateau-shaped particle images. Particles of Gaussian image shape result from fully labelled particles with small image diameters and are commonly used in PIV measurements. Such particles are also utilized for the determination of the continuous phase velocities in the experimental part of the present study. Monte Carlo simulations show that ring-shaped particle images have a superior behavior, i.e. they assume a reduced displacement estimation error for noisy as well as for noise-free image data, compared to Gaussian and plateau-shaped particle images. This is also true for large particle image diameters when particle images are intersected at interrogation window borders. Measurements are performed on a suspension containing 5 Vol.-% surface labelled, refractive index matched 60$μ$m PMMA particles. Simultaneously, $μ$PIV measurements of the carrier liquid flow are performed utilizing 1.19$μ$m fluorescent PS particles. Overall, the present study demonstrates theoretically and experimentally that the usage of suspension particles with ring-shaped images is suitable for $μ$PIV measurements to gain detailed insights into suspension bulk dynamics.

physics.flu-dyn↗

arXiv2020

On the calibration of Astigmatism particle tracking velocimetryfor suspensions of different volume fractions

In the present study we demonstrate for the first time how Astigmatism Particle Tracking Velocimetry (APTV) can be utilized to measure suspensions dynamics. Measurements were successfully performed in monodisperse, refractive index matched suspensions of up to a volume fraction of $Φ=19.9\%$. For this, a small percentage of the particles is labeled with fluorescent dye acting as tracers for the particle tracking procedure. Calibration results show, that a slight deviation of the refractive index of liquid and particles leads to a strong shape change of the calibration curve with respect to the unladen case. This effect becomes more severe along the channel height. To compensate the shape change of the calibration curves the interpolation technique developed by Brockmann et al. (Experiments in Fluids, 61(2), 67, \citeyear{brockmann2020utilizing}) is adapted. Using this technique, the interpolation procedure is applied to suspensions with 6 different volume fractions ranging from $Φ<0.01\%$ to $Φ=19.9\%$. To determine the effect of volume fraction on the perfomance of the method, the depth reconstruction error $σ_z$ and the measurement volume depth $Δz$, obtained in different calibration measurements, are estimated. Here, a relative position reconstruction accuracy of $σ_z$/$Δz$=0.90\% and $σ_z$/$Δz$=2.53\% is achieved for labeled calibration particles in dilute ($Φ<0.01\%$) and semi-dilute ($Φ\approx19.9\%$) suspensions, respectively. The measurement technique is validated for a laminar flow in a straight rectangular channel with a cross-sectional area of 2.55$\times$30\,mm$^2$. Uncertainties of 1.39\% and 3.34\% for the in-plane and 9.04\% and 22.57\% for the out-of-plane velocity with respect to the maximum streamwise velocity are achieved, at solid volume fractions of $Φ<0.01\%$ and $Φ=19.9\%$, respectively.

physics.flu-dyn↗

arXiv2020

Insights into Leading Edge Vortex Formation and Detachment on a Pitching and Plunging Flat Plate

The present study is a prelude to applying different flow control devices on pitching and plunging airfoils with the intention of controlling the growth of the leading edge vortex (LEV); hence, the lift under unsteady stall conditions. As a pre-requisite, the parameters influencing the development of the LEV topology must be fully understood, and this constitutes the main motivation of the present experimental investigation. The aims of this study are twofold. First, an approach is introduced to validate the comparability between flow fields and LEV characteristics of two different facilities using water and air as working media by making use of a common baseline case. The motivation behind this comparison is that with two facilities the overall parameter range can be greatly expanded. This comparison includes an overview of the respective parameter ranges, control of the airfoil kinematics and careful scrutiny of how post-processing procedures of velocity data from time-resolved particle image velocimetry (PIV) influence the integral properties and topological features used to characterise the LEV development. Second, and based on results coming from both facilities, the appearance of secondary structures and their effect on LEV detachment over an extended parameter range is studied. A Lagrangian flow field analysis, based on finite-time Lyapunov Exponent (FTLE) ridges, allows precise identification of secondary structures and reveals that their emergence is closely correlated to a vortex Reynolds number threshold computed from the LEV circulation. This threshold is used to model the temporal onset of secondary structures. Further analysis indicates that the emergence of secondary structures causes the LEV to stop accumulating circulation if the shear layer angle at the leading edge of the flat plate has ceased to increase.

physics.flu-dyn↗

arXiv2020

Delaying Leading Edge Vortex Detachment by Plasma Flow Control at Topologically Critical Locations

Flapping wing propulsion offers unrivalled manoeuvrability and efficiency at low flight speeds and in hover. These advantages are attributed to the leading edge vortex developing on an unsteady wing, which induces additional lift. We propose and validate a manipulation hypothesis that allows prolongation of the leading edge vortex growth phase, by delaying its detachment with the aid of flow control. This approach targets an overall lift increase on unsteady airfoils. A dielectric barrier discharge plasma actuator is successfully used to compress secondary structures upstream of the main vortex on a pitching and plunging flat plate. To determine flow control timing and location, the tangential velocity on the airfoil surface is used, which is also used to quantify topological effects of flow control. This flow control is then tested for different motion kinematics and on a NACA 0012 airfoil. Significant increase of the peak circulation of the leading edge vortex of about 20% for all cases with flow control indicates that this approach is applicable for various kinematics, dynamics and airfoil types.

physics.flu-dyn↗

arXiv2017

Suspensions of finite-size neutrally-buoyant spheres in turbulent duct flow

We study the turbulent square duct flow of dense suspensions of neutrally-buoyant spherical particles. Direct numerical simulations (DNS) are performed in the range of volume fractions $ϕ=0-0.2$, using the immersed boundary method (IBM) to account for the dispersed phase. Based on the hydraulic diameter a Reynolds number of $5600$ is considered. We report flow features and particle statistics specific to this geometry, and compare the results to the case of two-dimensional channel flows. In particular, we observe that for $ϕ=0.05$ and $0.1$, particles preferentially accumulate on the corner bisectors, close to the duct corners as also observed for laminar square duct flows of same duct-to-particle size ratios. At the highest volume fraction, particles preferentially accumulate in the core region. For channel flows, in the absence of lateral confinement particles are found instead to be uniformily distributed across the channel. We also observe that the intensity of the cross-stream secondary flows increases (with respect to the unladen case) with the volume fraction up to $ϕ=0.1$, as a consequence of the high concentration of particles along the corner bisector. For $ϕ=0.2$ the turbulence activity is strongly reduced and the intensity of the secondary flows reduces below that of the unladen case. The friction Reynolds number increases with $ϕ$ in dilute conditions, as observed for channel flows. However, for $ϕ=0.2$ the mean friction Reynolds number decreases below the value for $ϕ=0.1$.

physics.flu-dyn↗