arXiv subjects

Jeroen van Tilborg

Publications and source records attributed to Jeroen van Tilborg.

15 recordsLinked to original sources

arXiv2026

Energy-resolved measurement of individual GeV muon tracks generated by electrons from a compact Laser-Plasma Accelerator

Recently, the possibility of LPA-produced muon beams has gained significant interest within the accelerator application community. Directional, multi-GeV muons can be produced via Bethe-Heitler interactions when multi-GeV electrons hit solid targets. They are highly penetrating and, thanks to the compactness of the LPA, offer a path toward a deployable, active muon source. At the BELLA Center of the Lawrence Berkeley National Laboratory, we previously unambiguously detected muons generated during the interaction of multi-GeV electron beams with a 4 meter-thick electron beam dump. A new campaign has now extended our diagnostic capabilities to single-muon trajectory reconstruction and energy measurements. The setup allowed us to individually reconstruct each muon trajectory, defined by us as a muon passing through three detectors used for the reconstruction. For a subset of events, we extracted the muon energy from the magnetic-field bending angle, demonstrating production of GeV-scale muons. This work provides a key demonstration of track-based active-source muography, which enables non-invasive 3D density mapping of concealed or inaccessible samples, and it will accelerate the development of active LPA-based muon sources where compactness, controlled directionality, low divergence, and deep penetration are required.

physics.acc-ph↗

arXiv2026

Radiation damage to normal mammalian tissue in vivo with laser-driven protons at ultra-high instantaneous dose rate

The differential sparing of normal tissues relative to tumor control observed at ultra-high dose rates, referred to as the FLASH effect, has recently gained considerable attention. The therapeutic advantages of FLASH radiotherapy are expected to be further amplified through the use of protons and ions, which enable precise dose deposition at tumor depth while minimizing irradiation of healthy tissues proximal and distal to the target. Nevertheless, the mechanism underlying this sparing effect remains poorly understood. Laser-driven proton accelerators are capable of delivering uniquely high instantaneous dose rates in ultrashort bunches. Here, we report the first in vivo investigation of normal tissue response to laser-driven proton irradiation, with controlled exposures to 8 MeV protons, delivering total doses up to 50 Gy at 2 Gy per laser shot. Our findings reveal a reduction in tissue swelling following laser-driven proton treatment compared with X-ray irradiations at conventional dose rates. RNA sequencing identified differential gene expression associated with immune and epidermal programs following laser-driven proton irradiations at two different dose levels.

physics.med-ph↗

arXiv2025

Measurement of directional muon beams generated at the Berkeley Lab Laser Accelerator

We present the detection of directional muon beams produced using a PW laser at the Lawrence Berkeley National Laboratory. The muon source is a multi-GeV electron beam generated in a 30 cm laser plasma accelerator interacting with a high-Z converter target. The GeV photons resulting from the interaction are converted into a high-flux, directional muon beam via pair production. By employing scintillators to capture delayed events, we were able to identify the produced muons and characterize the source. Using theoretical knowledge of the muon production process combined with simulations that are in excellent agreement with the experiments, we demonstrate that the multi-GeV electron beams produce GeV-scale muons in numbers far exceeding those from cosmic background. Laser-plasma-accelerator-based muon sources can therefore enhance muon imaging applications thanks to their compactness, directionality, and high yields, which reduce the exposure time by orders of magnitude compared to cosmic ray muons. Using the Geant4-based simulation code we developed to gain insight into the experimental results, we can design future experiments and applications based on LPA-generated muons.

physics.acc-ph↗

arXiv2025

Multi-messenger dynamic imaging of laser-driven shocks in water using a plasma wakefield accelerator

Understanding dense matter hydrodynamics is critical for predicting plasma behavior in environments relevant to laser-driven inertial confinement fusion. Traditional diagnostic sources face limitations in brightness, spatiotemporal resolution, and inability to detect relevant electromagnetic fields. In this work, we present a dual-probe, multi-messenger laser wakefield accelerator platform combining ultrafast X-rays and relativistic electron beams at 1 Hz, to interrogate a free-flowing water target in vacuum, heated by an intense 200 ps laser pulse. This scheme enables high-repetition-rate tracking of the interaction evolution using both particle types. Betatron X-rays reveal a cylindrically symmetric shock compression morphology assisted by low-density vapor, resembling foam-layer-assisted fusion targets. The synchronized electron beam detects time-evolving electromagnetic fields, uncovering charge separation and ion species differentiation during plasma expansion - phenomena not captured by photons or hydrodynamic simulations. We show that combining both probes provides complementary insights spanning kinetic to hydrodynamic regimes, highlighting the need for hybrid physics models to accurately predict fusion-relevant plasma behavior

physics.plasm-ph↗

arXiv2025

Design Initiative for a 10 TeV pCM Wakefield Collider

This document outlines a community-driven Design Study for a 10 TeV pCM Wakefield Accelerator Collider. The 2020 ESPP Report emphasized the need for Advanced Accelerator R\&D, and the 2023 P5 Report calls for the ``delivery of an end-to-end design concept, including cost scales, with self-consistent parameters throughout." This Design Study leverages recent experimental and theoretical progress resulting from a global R\&D program in order to deliver a unified, 10 TeV Wakefield Collider concept. Wakefield Accelerators provide ultra-high accelerating gradients which enables an upgrade path that will extend the reach of Linear Colliders beyond the electroweak scale. Here, we describe the organization of the Design Study including timeline and deliverables, and we detail the requirements and challenges on the path to a 10 TeV Wakefield Collider.

physics.acc-ph↗

arXiv2024

Dephasing of ion beams as Magnetic Vortex Acceleration regime transitions into a bubble-like field structure

The interaction of an ultra-intense laser pulse with a near critical density target results in the formation of a plasma channel, a strong azimuthal magnetic field and moving vortices. An application of this is the generation of energetic and collimated ion beams via Magnetic Vortex Acceleration. The optimized regime of Magnetic Vortex Acceleration is becoming experimentally accessible with new high intensity laser beamlines coming online and advances made in near critical density target fabrication. The robustness of the acceleration mechanism with realistic experimental conditions is examined with three-dimensional simulations. Of particular interest is the acceleration performance with different laser temporal contrast conditions, in some cases leading to pre-expanded target profiles prior to the arrival of the main pulse. Preplasma effects on the structure of the accelerating fields is explored, including a detailed analysis of the ion beam properties and the efficiency of the process. Improved scaling laws for the MVA mechanism, including the laser focal spot size effects, are presented.

physics.plasm-ph↗

arXiv2024

Design Optimization of Permanent-Magnet Based Compact Transport Systems for Laser-Driven Proton Beams

Laser-driven (LD) ion acceleration has been explored in a newly constructed short focal length beamline at the BELLA petawatt facility (interaction point 2, iP2). For applications utilizing such LD ion beams, a beam transport system is required, which for reasons of compactness be ideally contained within 3 m. The large divergence and energy spread of LD ion beams present a unique challenge to transporting them compared to beams from conventional accelerators. This work gives an overview of proposed compact transport designs that can satisfy different requirements depending on the application for the iP2 proton beamline such as radiation biology, material science, and high energy density science. These designs are optimized for different parameters such as energy spread and peak proton density according to an application's need. The various designs consist solely of permanent magnet elements, which can provide high magnetic field gradients on a small footprint. While the field strengths are fixed, we have shown that the beam size and energy can be tuned effectively by varying the placement of the magnets. The performance of each design was evaluated based on high order particle tracking simulations of typical LD proton beams. A more detailed investigation was carried out for a design to deliver 10 MeV LD accelerated ions for radiation biology applications. With these transport system designs, the iP2 beamline is ready to house various application experiments.

physics.acc-ph↗

arXiv2023

Beam Delivery and Beamstrahlung Considerations for Ultra-High Energy Linear Colliders

As part of the Snowmass'21 community planning excercise, the Advanced Accelerator Concepts (AAC) community proposed future linear colliders with center-of-mass energies up to 15 TeV and luminosities up to 50$\times10^{34}$ cm$^{-2}$s$^{-1}$ in a compact footprint. In addition to being compact, these machines must also be energy efficient. We identify two challenges that must be addressed in the design of these machines. First, the Beam Delivery System (BDS) must not add significant length to the accelerator complex. Second, beam parameters must be chosen to mitigate beamstrahlung effects and maximize the luminosity-per-power of the machine. In this paper, we review advances in plasma lens technology that will help to reduce the length of the BDS system and we detail new Particle-in-Cell simulation studies that will provide insight into beamstrahlung mitigation techniques. We apply our analysis to both $e^+e^-$ and $γγ$ colliders.

physics.acc-ph↗

arXiv2022

Online Charge Measurement for Petawatt Laser-Driven Ion Acceleration

Laser-driven ion beams have gained considerable attention for their potential use in multidisciplinary research and technology. Pre-clinical studies into their radiobiological effectiveness have established the prospect of using laser-driven ion beams for radiotherapy. In particular, research into the beneficial effects of ultra-high instantaneous dose rates is enabled by the high ion bunch charge and uniquely short bunch lengths present for laser-driven ion beams. Such studies require reliable, online dosimetry methods to monitor the bunch charge for every laser shot to ensure that the prescribed dose is accurately applied to the biological sample. In this paper we present the first successful use of an Integrating Current Transformer (ICT) for laser-driven ion accelerators. This is a non-invasive diagnostic to measure the charge of the accelerated ion bunch. It enables online dose measurements in radiobiological experiments and facilitates ion beam tuning, in particular, optimization of the laser ion source and alignment of the proton transport beamline. We present the ICT implementation and the correlation with other diagnostics such as radiochromic films, a Thomson parabola spectrometer and a scintillator.

physics.acc-ph↗

arXiv2022

High average power ultrafast laser technologies for driving future advanced accelerators

Large scale laser facilities are needed to advance the energy frontier in high energy physics and accelerator physics. Laser plasma accelerators are core to advanced accelerator concepts aimed at reaching TeV electron electron colliders. In these facilities, intense laser pulses drive plasmas and are used to accelerate electrons to high energies in remarkably short distances. A laser plasma accelerator could in principle reach high energies with an accelerating length that is 1000 times shorter than in conventional RF based accelerators. Notionally, laser driven particle beam energies could scale beyond state of the art conventional accelerators. LPAs have produced multi GeV electron beams in about 20 cm with relative energy spread of about 2 percent, supported by highly developed laser technology. This validates key elements of the US DOE strategy for such accelerators to enable future colliders but extending best results to date to a TeV collider will require lasers with higher average power. While the per pulse energies envisioned for laser driven colliders are achievable with current lasers, low laser repetition rates limit potential collider luminosity. Applications will require rates of kHz to tens of kHz at Joules of energy and high efficiency, and a collider would require about 100 such stages, a leap from current Hz class LPAs. This represents a challenging 1000 fold increase in laser repetition rates beyond current state of the art. This whitepaper describes current research and outlook for candidate laser systems as well as the accompanying broadband and high damage threshold optics needed for driving future advanced accelerators.

physics.acc-ph↗

arXiv2022

Transformative Technology for FLASH Radiation Therapy: A Snowmass 2021 White Paper

Conventional cancer therapies include surgery, radiation therapy, chemotherapy, and, more recently, immunotherapy. These modalities are often combined to improve the therapeutic index. The general concept of radiation therapy is to increase the therapeutic index by creating a physical dose differential between tumors and normal tissues through precision dose targeting, image guidance, and high radiation beams that deliver radiation dose with high conformality, e.g., protons and ions. However, treatment and cure are still limited by normal tissue radiation toxicity, with many patients experiencing acute and long-term side effects. Recently, however, a fundamentally different paradigm for increasing the therapeutic index of radiation therapy has emerged, supported by preclinical research, and based on the FLASH radiation effect. FLASH radiation therapy (FLASH-RT) is an ultra-high dose-rate delivery of a therapeutic radiation dose within a fraction of a second. Experimental studies have shown that normal tissues seem to be universally spared at these high dose rates, whereas tumors are not. The dose delivery conditions are not yet fully characterized. Still, it is currently estimated that large doses of 10 Gy or more delivered in 200 ms or less produce normal tissue sparing effects yet effectively kill tumor cells. There is a great opportunity, but also many technical challenges, for the accelerator community to create the required dose rates with novel and compact accelerators to ensure the safe delivery of FLASH radiation beams.

physics.med-ph↗

arXiv2022

Snowmass 2021 Accelerator Frontier White Paper: Near Term Applications driven by Advanced Accelerator Concepts

While the long-term vision of the advanced accelerator community is aimed at addressing the challenges of future collider technology, it is critical that the community takes advantage of the opportunity to make large societal impact through its near-term applications. In turn, enabling robust applications strengthens the quality, control, and reliability of the underlying accelerator infrastructure. The white paper contributions that are solicited here will summarize the near-term applications ideas presented by the advanced accelerator community, assessing their potential impact, discussing scientific and technical readiness of concepts, and providing a timeline for implementation.

physics.acc-ph↗

arXiv2021

Effect of Nozzle Curvature on Supersonic Gas Jets Used in Laser-Plasma Acceleration

Supersonic gas jets produced by converging-diverging (C-D) nozzles are commonly used as targets for laser-plasma acceleration (LPA) experiments. A major point of interest for these targets is the gas density at the region of interaction where the laser ionizes the gas plume to create a plasma, providing the acceleration structure. Tuning the density profiles at this interaction region is crucial to LPA optimization. A "flat-top" density profile is desired at this line of interaction to control laser propagation and high energy electron acceleration, while a short high-density profile is often preferred for acceleration of lower-energy tightly-focused laser-plasma interactions. A particular design parameter of interest is the curvature of the nozzle's diverging section. We examine three nozzle designs with different curvatures: the concave "bell", straight conical and convex "trumpet" nozzles. We demonstrate that, at mm-scale distances from the nozzle exit, the trumpet and straight nozzles, if optimized, produce "flat-top" density profiles whereas the bell nozzle creates focused regions of gas with higher densities. An optimization procedure for the trumpet nozzle is derived and compared to the straight nozzle optimization process. We find that the trumpet nozzle, by providing an extra parameter of control through its curvature, is more versatile for creating flat-top profiles and its optimization procedure is more refined compared to the straight nozzle and the straight nozzle optimization process. We present results for different nozzle designs from computational fluid dynamics (CFD) simulations performed with the program ANSYS Fluent and verify them experimentally using neutral density interferometry.

physics.plasm-ph↗

arXiv2017

Plasma Equilibrium inside Various Cross-Section Capillary Discharges

Plasma properties inside a hydrogen-filled capillary discharge waveguide were modeled with dissipative magnetohydrodynamic simulations to enable analysis of capillaries of circular and square cross-sections implying that square capillaries can be used to guide circularly-symmetric laser beams. When the quasistationary stage of the discharge is reached, the plasma and temperature in the vicinity of the capillary axis has almost the same profile for both the circular and square capillaries. The effect of cross-section on the electron beam focusing properties were studied using the simulation-derived magnetic field map. Particle tracking simulations showed only slight effects on the electron beam symmetry in the horizontal and diagonal directions for square capillary.

physics.plasm-ph↗

arXiv2017

Laser beam coupling with capillary discharge plasma for laser wakefield acceleration applications

One of the most robust methods, demonstrated up to date, of accelerating electron beams by laser-plasma sources is the utilization of plasma channels generated by the capillary discharges. These channels, i.e., plasma columns with a minimum density along the laser pulse propagation axis, may optically guide short laser pulses, thereby increasing the acceleration length, leading to a more efficient electron acceleration. Although the spatial structure of the installation is simple in principle, there may be some important effects caused by the open ends of the capillary, by the supplying channels etc., which require a detailed 3D modeling of the processes taking place in order to get a detailed understanding and improve the operation. However, the discharge plasma, being one of the most crucial components of the laser-plasma accelerator, is not simulated with the accuracy and resolution required to advance this promising technology. In the present work, such simulations are performed using the code MARPLE. First, the process of the capillary filling with a cold hydrogen before the discharge is fired, through the side supply channels is simulated. The main goal of this simulation is to get a spatial distribution of the filling gas in the region near the open ends of the capillary. A realistic geometry is used for this and the next stage simulations, including the insulators, the supplying channels as well as the electrodes. Second, the simulation of the capillary discharge is performed with the goal to obtain a time-dependent spatial distribution of the electron density near the open ends of the capillary as well as inside the capillary. Finally, to evaluate effectiveness of the beam coupling with the channeling plasma wave guide and electron acceleration, modeling of laser-plasma interaction was performed with the code INF&RNO

physics.plasm-ph↗