Searcharxiv⌕ Search

arXiv subjects

Jingzhou Zhao

Publications and source records attributed to Jingzhou Zhao.

7 recordsLinked to original sources

A 40 Gbit/s FPGA-based RoCEv2 transport for detector readout: development and performance

Recording the complete input of a detector trigger allows trigger algorithms to be replayed and studied offline. For the BESIII main drift chamber (MDC), this requires moving tens of Gbit/s from trigger FPGAs into server memory without loss. Remote direct memory access over Converged Ethernet (RoCEv2) lets commercial network adapters write such data into host memory. Detector readout also needs record boundaries that the receiver can check, replay from a verified copy, and host buffers that are reused only after consumption. We present a 40 Gbit/s FPGA RoCEv2 transport that provides these functions. Records are aggregated into CRC32C-checked blocks, and unacknowledged data are kept in DDR memory and verified before replay. Acknowledgment-aware retention writes to DDR only the data that are not acknowledged in time. The transport runs on a ZCU102 board and on the 9U VME Trigger Core Board (TCB). With records of 128 B to 4 KiB it comes within 0.4% of the packetization limit of the link, delivering 36.9 Gbit/s of payload at a path MTU of 1024 B, and its block latency is set by the time needed to fill a block. On a direct link, acknowledgment-aware retention cuts DDR writes for large blocks from 106% to 0.03% of the payload, and injected DDR access errors stay within their queue pair. On the TCB, three 16.4 TB transfers through two switches lost at most five packets each, all recovered by replay. An installation at the MDC is under test.

physics.ins-det↗

Low-Latency Beam-Background Suppression for the BESIII Trigger System Using Machine Learning Trained on Experimental Data

Beam-induced backgrounds contribute to the trigger and data-acquisition rate at high-luminosity electron-positron colliders. Their dependence on beam and machine conditions motivates data-driven studies alongside simulation. A data-driven machine-learning method for trigger-level beam-background suppression is developed using experimental data recorded by BESIII. Compact neural-network classifiers are trained and evaluated for two trigger configurations: one based only on tracking and time-of-flight information, and one based only on electromagnetic-calorimeter information. Each classifier uses 48 binary Level-1 trigger conditions of the BESIII detector. The models distinguish hadron events from beam-background events and are evaluated against the established trigger selection at matched hadron-event efficiency. Relative to the established trigger selection, the beam-background false-positive rate is reduced by 20-60% across the studied configurations and center-of-mass energies, with stable suppression performance as tested using random-trigger data. Hardware-oriented synthesis indicates that the compact network is suitable for low-latency FPGA implementation. The proposed method can reduce the fraction of beam-background events in the trigger stream in future BESIII trigger upgrades. It also provides a reference for trigger optimization at future high-luminosity electron-positron colliders.

hep-ex↗

Design and Characteristics of a Thin-Film ThermoMesh for the Efficient Embedded Sensing of a Spatio-Temporally Sparse Heat Source

This work presents ThermoMesh, a passive thin-film thermoelectric mesh sensor designed to detect and characterize spatio-temporally sparse heat sources through conduction-based thermal imaging. The device integrates thermoelectric junctions with linear or nonlinear interlayer resistive elements to perform simultaneous sensing and in-sensor compression. We focus on the single-event (1-sparse) operation and define four performance metrics: range, efficiency, sensitivity, and accuracy. Numerical modeling shows that a linear resistive interlayer flattens the sensitivity distribution and improves minimum sensitivity by approximately tenfold for a $16\times16$ mesh. Nonlinear temperature-dependent interlayers further enhance minimum sensitivity at scale: a ceramic negative-temperature-coefficient (NTC) layer over 973-1273K yields a $\sim14{,}500\times$ higher minimum sensitivity than the linear design at a $200\times200$ mesh, while a VO$_2$ interlayer modeled across its metal-insulator transition (MIT) over 298-373K yields a $\sim24\times$ improvement. Using synthetic 1-sparse datasets with white boundary-channel noise at a signal-to-noise ratio of 40dB, the VO$_2$ case achieved $98\%$ localization accuracy, a mean absolute temperature error of $0.23$K, and a noise-equivalent temperature (NET) of $0.07$K. For the ceramic-NTC case no localization errors were observed under the tested conditions, with a mean absolute temperature error of $1.83$K and a NET of $1.49$K. These results indicate that ThermoMesh could enable energy-efficient embedded thermal sensing in scenarios where conventional infrared imaging is limited, such as molten-droplet detection or hot-spot monitoring in harsh environments.

cs.RO↗

Performance of the Unified Readout System of Belle II

The Belle II experiment at the SuperKEKB collider at KEK, Tsukuba, Japan has successfully started taking data with the full detector in March 2019. Belle II is a luminosity frontier experiment of the new generation to search for physics beyond the Standard Model of elementary particles, from precision measurements of a huge number of B and charm mesons and tau leptons. In order to read out the events at a high rate from the seven subdetectors of Belle II, we adopt a highly unified readout system, including a unified trigger timing distribution system (TTD), a unified high speed data link system (Belle2link), and a common backend system to receive Belle2link data. Each subdetector frontend readout system has a field-programmable gate array (FPGA) in which unified firmware components of the TTD receiver and Belle2link transmitter are embedded. The system is designed for data taking at a trigger rate up to 30 kHz with a dead-time fraction of about 1% in the frontend readout system. The trigger rate is still much lower than our design. However, the background level is already high due to the initial vacuum condition and other accelerator parameters, and it is the most limiting factor of the accelerator and detector operation. Hence the occupancy and radiation effects to the frontend electronics are rather severe, and they cause various kind of instabilities. We present the performance of the system, including the achieved trigger rate, dead-time fraction, stability, and discuss the experience gained during the operation.

physics.ins-det↗

New version of high performance Compute Node for PANDA Streaming DAQ system

PANDA is one of the major experiments currently under construction at FAIR/Darmstadt. Its focus is physics with high intensity and high quality anti-proton beams with momenta up to 15 GeV/c. Event rates up to 20MHz, and a typical event size between 1.5 KB and 4.5 KB. lead to data rates as high as 200 GB/s. A trigger-less streaming DAQ system is introduced in this paper, featuring event filtering based on FPGAs and a CPU/GPU farm. The Compute Node (CN) is the central board FPGA based component in this system. A new version of the ATCA based CN is presented. Its main features include high speed data transmission, massive data buffering capabilities to support large latency for complex decion algorithms, high performance data processing and ethernet connectivity. First test results with a prototype are presented.

physics.ins-det↗

FPGA Online Tracking Algorithm for the PANDA Straw Tube Tracker

A novel FPGA based online tracking algorithm for helix track reconstruction in a solenoidal field, developed for the PANDA spectrometer, is described. Employing the Straw Tube Tracker detector with 4636 straw tubes, the algorithm includes a complex track finder, and a track fitter. Implemented in VHDL, the algorithm is tested on a Xilinx Virtex-4 FX60 FPGA chip with different types of events, at different event rates. A processing time of 7 $μ$s per event for an average of 6 charged tracks is obtained. The momentum resolution is about 3\% (4\%) for $p_t$ ($p_z$) at 1 GeV/c. Comparing to the algorithm running on a CPU chip (single core Intel Xeon E5520 at 2.26 GHz), an improvement of 3 orders of magnitude in processing time is obtained. The algorithm can handle severe overlapping of events which are typical for interaction rates above 10 MHz.

physics.ins-det↗

The ONSEN Data Reduction System for the Belle II Pixel Detector

We present an FPGA-based online data reduction system for the pixel detector of the future Belle II experiment. The occupancy of the pixel detector is estimated at 3 %. This corresponds to a data output rate of more than 20 GB/s after zero suppression, dominated by background. The Online Selection Nodes (ONSEN) system aims to reduce the background data by a factor of 30. It consists of 33 MicroTCA cards, each equipped with a Xilinx Virtex-5 FPGA and 4 GiB DDR2 RAM. These cards are hosted by 9 AdvancedTCA carrier boards. The ONSEN system buffers the entire output data from the pixel detector for up to 5 seconds. During this time, the Belle II high-level trigger PC farm performs an online event reconstruction, using data from the other Belle II subdetectors. It extrapolates reconstructed tracks to the layers of the pixel detector and defines regions of interest around the intercepts. Based on this information, the ONSEN system discards all pixels not inside a region of interest before sending the remaining hits to the event builder system. During a beam test with one layer of the pixel detector and four layers of the surrounding silicon strip detector, including a scaled-down version of the high-level trigger and data acquisition system, the pixel data reduction using regions of interest was exercised. We investigated the data produced in more than 20 million events and verified that the ONSEN system behaved correctly, forwarding all pixels inside regions of interest and discarding the rest.

physics.ins-det↗