arXiv subjects

Jinxin Liu

Publications and source records attributed to Jinxin Liu.

60 records · Page 4Linked to original sources

arXiv2019

Readout Electronics of T0 Detector in the External Target Experiment of CSR in HIRFL

T0 detector, based on Multi-gap Resistive Plate Chambers (MRPC) technology, is one of the key components in the External Target Experiment. Through precision measurements of the MRPC signals, timing of the beam impact on target can be obtained and used as the start time for other detectors. A readout electronics system was designed for the T0 detector. Based on the NINO ASIC, front-end-electronics (FEE) circuits which can achieve high precision leading-edge discrimination and Charge-to-Time Conversion (QTC) were designed for the internal and external MRPCs of the T0 detector. The output pulse of the FEE is then digitized by high precision time digitization modules with Time-to-Digital Converters (TDCs), trigger matching and other control logic integrated within Field Programmable Gate Array (FPGA) devices. To evaluate the functionality and performance, we also conducted a series of tests of the electronics. Results indicate that the system functions well and the time precision of the electronics is better than 21 ps, which satisfies the application requirement.

physics.ins-det↗

arXiv2019

Bunch-by-bunch Beam Transverse Feedback Electronics Designed for SSRF

Shanghai Synchrotron Radiation Facility (SSRF), is one of the third-generation high-beam current (3.5 GeV) synchrotron light sources. In the storage ring of SSRF, multi-bunch instabilities would increase beam emittance and energy spread, which degrade beam quality and even cause beam loss. To address the above issues, a Transverse Feedback System is indispensable for SSRF, in which the key component is the bunch-by-bunch transverse feedback electronics. The whole feedback system consists of five main parts: Beam Position Monitor (BPM), RF front-end, signal processor, RF amplifier, and vertical/horizontal transverse kickers. The dissertation focuses on the signal processor we design, which is the main part of the feedback electronics. We conducted initial testing on the signal processor to evaluate its performance and function. Test results indicate that ENOB of the Analog-to-Digital Conversion circuit is better than 10 bit with 100 MHz input signal, and remains better than 9.5 bit up to 300 MHz, which is good enough for the required 7.9 bit; the frequency response of the whole system also concords well with the simulation results, and the suppression in amplitude response at the critical frequency points is better 35 dB while the uncertainty of phase response is better than 2 degree, all meeting the application requirement.

physics.ins-det↗

arXiv2019

Design and testing of a bunch-by-bunch beam position transverse feedback processor

Shanghai Synchrotron Radiation Facility (SSRF) is a 3.5 GeV storage ring with a bunch rate of 499.654 MHz, harmonic number of 720, and circumference of 432 meters. SSRF injection works at 3.5 GeV, where the multi-bunch instabilities limit the maximum stored current. In order to suppress multi-bunch instabilities caused by transverse impedance, a bunch-by-bunch transverse feedback system is indispensable for SSRF. The key component of that system is the bunch-by-bunch transverse feedback electronics. An important task in the electronics is precise time synchronization. In this paper, a novel clock synchronization and precise delay adjustment method based on the PLLs and delay lines are proposed. Test results indicate that the ENOB (Effective Number Of Bits) of the analog-to-digital conversion circuit is better than 9 bits in the input signal frequency range from 100 kHz to 700 MHz, and the closed loop attenuation at the critical frequency points is better than 40 dB. The initial commissioning tests with the beam in SSRF are also conducted, and the results are consistent with the expectations.

physics.ins-det↗

arXiv2018

Mismatch error correction for time interleaved analog-to-digital converter over a wide frequency range

High-speed high-resolution Analog-to-Digital Conversion is the key part for waveform digitization in physics experiments and many other domains. This paper presents a new fully digital correction of mismatch errors among the channels in Time Interleaved Analog-to-Digital Converter (TIADC) systems. We focus on correction with wide-band input signal, which means that we can correct the mismatch errors for any frequency point in a broad band with only one set of filter coefficients. Studies were also made to show how to apply the correction algorithm beyond the base band, i.e. other Nyquist zones in the under-sampling situation. Structure of the correction algorithm is presented in this paper, as well as simulation results. To evaluate the correction performance, we actually conducted a series of tests with two TIADC systems. The results indicate that the performance of both two TIADC systems can be greatly improved by correction, and the Effective Number Of Bits (ENOB) is successfully improved to be better than 9.5 bits and 5.5 bits for an input signal up to the bandwidth (-3dB) range in the 1.6-Gsps 14-bit and the 10-Gsps 8-bit TIADC systems, respectively. Tests were also conducted for input signal frequencies in the second Nyquist zone, which shows that the correction algorithms also work well as expected.

eess.SP↗

arXiv2018

High-speed RF Switch Electronics for picking up of Electron-Positron Beam Bunches

Beam diagnostics is important to guarantee good quality of beam in particle accelerator. Both the electron and positron run in the tunnel in some modern electron positron colliders such as Circular Electron Positron Collider (CEPC) to be built and Beijing Electron Positron Collider II (BEPC II). To measure the electron and positron beams, picking up of these two different bunches in real time is of notable concern. Because the time interval between adjacent electron and positron bunches is quite small, for example, 6 ns in CEPC, high-speed switch electronics is required. This paper presents the prototype design of a high-speed radio frequency (RF) electronics that can pick up nanosecond positron-electron beam bunches with a switching time of less than 6 ns. Fast separation of electron and positron is achieved based on RF switches and precise delay adjustment of the controlling signals (~10 ps). Initial tests have been conducted in the laboratory to evaluate the performance of electronics, the results indicate that this circuit can successfully pick up the bunch signal within a time interval of 6 ns, which makes it possible to further measure the electron and position beams simultaneously.

physics.acc-ph↗

arXiv2016

Micro-reflectance and transmittance spectroscopy: a versatile and powerful tool to characterize 2D materials

Optical spectroscopy techniques such as differential reflectance and transmittance have proven to be very powerful techniques to study 2D materials. However, a thorough description of the experimental setups needed to carry out these measurements is lacking in the literature. We describe a versatile optical microscope setup to carry out differential reflectance and transmittance spectroscopy in 2D materials with a lateral resolution of ~1 micron in the visible and near-infrared part of the spectrum. We demonstrate the potential of the presented setup to determine the number of layers of 2D materials and to characterize their fundamental optical properties such as excitonic resonances. We illustrate its performance by studying mechanically exfoliated and chemical vapor-deposited transition metal dichalcogenide samples.

cond-mat.mes-hall↗