arXiv subjects

Joanna Aizenberg

Publications and source records attributed to Joanna Aizenberg.

At least 19 recordsLinked to original sources

arXiv2026

Rotational 3D printing of active-passive filaments and lattices with programmable shape morphing

Natural filaments, such as proteins, plant tendrils, octopus tentacles, and elephant trunks, can transform into arbitrary three-dimensional shapes that carry out vital functions. Their shape-morphing behavior arises from intricate patterning of active and passive regions, which are difficult to replicate in synthetic matter. Here, we introduce a filament-centric strategy for programmable shape morphing in which intrinsic curvature and twist are directly encoded within multimaterial elastomeric filaments during fabrication. By harnessing rotational multimaterial 3D printing (RM-3DP), we directly prescribe the filament's natural curvature--twist field $\mathbf{k}(s)$ through controlled material distribution and helical liquid crystal mesogen alignment. When heated above their nematic-to-isotropic transition temperature ($T_\mathrm{NI}$), the helically aligned LCE regions contract along their local director field, while passive regions remain essentially unchanged. This approach enables independent control of bending and torsion at every cross-section along the filament centerline: the principal natural curvatures of the filament along two orthogonal axes as well as the local twist. Next, we printed architected lattices composed of unit cells formed by sinusoidal filaments that either reversibly contract, expand, or exhibit out-of-plane deformations. Discrete elastic rod simulations of Janus filaments with different natural curvatures and twist, which are interconnected within the printed lattices, allow accurate prediction of their observed shape-morphing behavior. By integrating active-passive elastomers, additive manufacturing, and computational modeling, we have created shape-morphing matter with complex programmable responses for applications that rely on adaptive, robotic, or deployable architectures.

cond-mat.soft↗

arXiv2023

Emergent collective motion of self-propelled condensate droplets

Recently, there is much interest in droplet condensation on soft or liquid/liquid-like substrates. Droplets can deform soft and liquid interfaces resulting in a wealth of phenomena not observed on hard, solid surfaces (e.g., increased nucleation, inter-droplet attraction). Here, we describe a unique complex collective motion of condensate water droplets that emerges spontaneously when a solid substrate is covered with a thin oil film. Droplets move first in a serpentine, self-avoiding fashion before transitioning to circular motions. We show that this self-propulsion (with speeds in the 0.1-1 mm/s range) is fuelled by the interfacial energy release upon merging with newly condensed but much smaller droplets. The resultant collective motion spans multiple length scales from submillimetre to several centimetres, with potentially important heat-transfer and water-harvesting applications.

cond-mat.soft↗

arXiv2022

Self-regulating surfaces for efficient liquid collection

To achieve efficient liquid collection, a surface must regulate incoming liquid accumulation with outgoing liquid transport. Often, this can be proposed to be achieved by functionalizing surfaces with non-wetting characteristics. Yet, there remain fundamental, practical limits to which non-wetting surfaces can effectively be employed. We instead utilize filmwise wetting to achieve liquid regulation via a Laplace pressure gradient induced by solid surface curvature. The key parameters affecting this capillary flow are then introduced, namely solid properties like scale and curvature and liquid properties like surface tension and density. The liquid regulation mechanism can then be employed in condensation and aerosol processes to generate enhanced flow, while the solid geometry needed to create this capillary flow itself is capable of affecting and enhancing liquid generation. Ultimately, the surface design framework can be customized to each unique application to optimize processes in HVAC, industrial steam generation, chemical depositions, and atmospheric water harvesting.

physics.flu-dyn↗

arXiv2020

Designing angle-independent structural colors using Monte Carlo simulations of multiple scattering

Disordered nanostructures with correlations on the scale of visible wavelengths can show angle-independent structural colors. These materials could replace dyes in some applications because the color is tunable and resists photobleaching. However, designing nanostructures with a prescribed color is difficult, especially when the application -- cosmetics or displays, for example -- requires specific component materials. A general approach to solving this constrained design problem is modeling and optimization: using a model that predicts the color of a given system, one optimizes the model parameters under constraints to achieve a target color. For this approach to work, the model must make accurate predictions, which is challenging because disordered nanostructures have multiple scattering. To address this challenge, we develop a Monte Carlo model that simulates multiple scattering of light in disordered arrangements of spherical particles or voids. The model produces quantitative agreement with measurements when we account for roughness on the surface of the film, particle polydispersity, and wavelength-dependent absorption in the components. Unlike discrete numerical simulations, our model is parameterized in terms of experimental variables, simplifying the connection between simulation and fabrication. To demonstrate this approach, we reproduce the color of the male mountain bluebird (Sialia currucoides) in an experimental system, using prescribed components and a microstructure that is easy to fabricate. Finally, we use the model to find the limits of angle-independent structural colors for a given system. These results enable an engineering design approach to structural color for many different applications.

cond-mat.soft↗

arXiv2019

Effect of surface chemistry on incorporation of nanoparticles within calcite single crystals

Inclusion of additives into calcite crystals allows one to embed non-native proprieties into the inorganic matrix and obtain new functional materials. Up to now, few parameters have been taken into account to evaluate the efficiency of inclusion of an additive. Taking inspiration from Nature, we grew calcite crystals in the presence of fluorescent silica nanoparticles carrying different functional groups (PluS-X) to investigate the effect of surface chemistry on the inclusion of the additives. PluS-X allowed us to keep constant all the particle characteristics, including size, while changing exposed functional groups and thus Zeta-potential. The effect on crystal morphology, the loading and distribution of PluS-X within the crystals have been evaluated with different microscopy techniques. Our data indicate that hydroxyl functionalized particles are entrapped more efficiently inside calcite single crystals without distortion of the crystal structure and inhibition of the growth.

cond-mat.mtrl-sci↗

arXiv2019

Liquid Collection on Welwitschia-Inspired Wavy Surfaces

Hydrophobic (HPo) surfaces for atmospheric water harvesting applications require sophisticated wettability and microstructure patterns, which suffer from high cost and low durability against severe mechanical and environmental degradations. Inspired by the leaves of Welwitschia mirabilis, a long lifespan desert-living plant, we present a robust superhydrophilic (SHPi) surface design which is capable of enhancing both dew condensation and fog capture. The surface consists of a parallel-aligned millimetric wavy topography on top of which random nanostructures are grown. By studying the liquid dynamics, we have shown a unique mechanism of water transport on the SHPi wavy surface by droplet splitting and Laplace pressure gradient. It has been revealed that the efficient water transport on the SHPi wavy surface synergistically interacts with the enhanced diffusion flux of water vapor on the convex regions and significantly improves the efficiency of filmwise condensation. We have further demonstrated that wavy features enhance the probability of fog droplet collisions by disturbing the air flow and increasing the mean free path of fog droplets.

physics.app-ph↗

arXiv2019

Wide-angle spectrally selective absorbers and thermal emitters based on inverse opals

Engineered optical absorbers are of substantial interest for applications ranging from stray light reduction to energy conversion. We demonstrate a large-area (centimeter-scale) metamaterial that features near-unity frequency-selective absorption in the mid-infrared wavelength range. The metamaterial comprises a self-assembled porous structure known as an inverse opal, here made of silica. The structure's large volume fraction of voids, together with the vibrational resonances of silica in the mid-infrared spectral range, reduce the metamaterial's refractive index to close to that of air and introduce considerable optical absorption. As a result, the frequency-selective structure efficiently absorbs incident light of both polarizations even at very oblique incidence angles. The absorber remains stable at high temperatures (measured up to ~900 degrees C), enabling its operation as a frequency-selective thermal emitter. The excellent performance of this absorber/emitter and ease of fabrication make it a promising surface coating for passive radiative cooling, laser safety, and other large-area applications.

physics.optics↗

arXiv2018

Film dynamics and lubricant depletion by droplets moving on lubricated surfaces

Lubricated surfaces have shown promise in numerous applications where impinging foreign droplets must be removed easily; however, before they can be widely adopted, the problem of lubricant depletion, which eventually leads to decreased performance, must be solved. Despite recent progress, a quantitative mechanistic explanation for lubricant depletion is still lacking. Here, we first explained the shape of a droplet on a lubricated surface by balancing the Laplace pressures across interfaces. We then showed that the lubricant film thicknesses beneath, behind, and wrapping around a moving droplet change dynamically with droplet's speed---analogous to the classical Landau-Levich-Derjaguin problem. The interconnected lubricant dynamics results in the growth of the wetting ridge around the droplet, which is the dominant source of lubricant depletion. We then developed an analytic expression for the maximum amount of lubricant that can be depleted by a single droplet. Counter-intuitively, faster moving droplets subjected to higher driving forces deplete less lubricant than their slower moving counterparts. The insights developed in this work will inform future work and the design of longer-lasting lubricated surfaces.

physics.flu-dyn↗

arXiv2018

Origins of liquid-repellency on structured, flat, and lubricated surfaces

There are currently three main classes of high-performance liquid-repellent surfaces: micro-/nano-structured lotus-effect superhydrophobic surfaces, flat surfaces grafted with 'liquid-like' polymer brushes, and various lubricated surfaces. Despite recent progress, the mechanistic understanding of the differences in droplet behavior on such surfaces is still under debate. We measured the dissipative force acting on a droplet moving on representatives of these classes at different velocities U = 0.01-1 mm/s using a cantilever force sensor with sub-uN accuracy, and correlated it to the contact line dynamics observed using optical interferometry at high spatial (micron) and temporal (< 0.1s) resolutions. We find that the dissipative force, due to very different physical mechanisms at the contact line, is independent of velocity on superhydrophobic surfaces, but depends non-linearly on velocity for flat and lubricated surfaces. The techniques and insights presented here will inform future work on liquid-repellent surfaces and enable their rational design.

physics.flu-dyn↗

arXiv2017

Liquid jet rebound upon impact on a soft gel

A liquid jet can stably bounce off a sufficiently soft gel, by following the contour of the dimple created upon impact. This new phenomenon is insensitive to the wetting properties of the gels and was observed for different liquids over a wide range of surface tensions, $γ$ = 24--72 mN/m. In contrast, other jet rebound phenomena are typically sensitive to $γ$: jet rebounds off a hard solid (e.g. superhydrophobic surface) or another liquid are possible only for high and low $γ$ liquids, respectively. This is because an air layer must be stabilized between the two interfaces. For a soft gel, no air layer is necessary and jet rebound remains stable even when there is direct liquid-gel contact.

physics.flu-dyn↗

arXiv2017

Oleoplaning droplets on lubricated surfaces

Recently, there has been much interest in using lubricated flat and nano-/micro-structured surfaces to achieve extreme liquid-repellency: any foreign droplet immiscible with the underlying lubricant layer was shown to slide off at a small tilt angle $<$ 5$^{\circ}$. This behavior was hypothesized to arise from a thin lubricant overlayer film sandwiched between the droplet and solid substrate, but this has not been observed experimentally. Here, using confocal optical interferometry, we are able to visualize the intercalated film under both static and dynamic conditions. We further demonstrate that the lubricant flow entrained by droplet motion can transform a partially dewetted film into a continuous layer, by generating a sufficient hydrodynamic force to lift the droplet over the solid substrate. The droplet is therefore oleoplaning, akin to tires hydroplaning on a wet road, with minimal dissipative force (down to 0.1 $μ$N for 1 $μ$l droplet when measured using a cantilever force sensor) and no contact line pinning. The techniques and insights presented in this study will inform future work on the fundamentals of wetting for lubricated surfaces and enable their rational design.

physics.flu-dyn↗

arXiv2016

Dropwise Condensation on Hydrophobic Cylinders

In this work, we studied the effect of the diameter of horizontal hydrophobic cylinders on droplet growth. We postulate that the concentration gradient created by natural convection around a horizontal circular cylinder is related to the droplet growth on the cylinder by condensation. We derive a simple scaling law of droplet growth and compare it with experimental results. The predicted negative exponent of drop diameter (d) as a function of cylinder diameter (D) at different time points is similar to the general trend of experimental data. Further, this effect of cylinder diameter on droplet growth is observed to be stronger than the supersaturation conditions created by different surface temperatures.

physics.flu-dyn↗

arXiv2015

Percolation lithography: Tuning and freezing disorder in 3D photonic crystals using partial wetting and drying

Although complex, hierarchical nanoscale geometries with tailored degrees of disorder are commonly found in biological systems, few simple self-assembly routes to fabricating synthetic analogues have been identified. We present two techniques that exploit basic capillary phenomena to finely control disorder in porous 3D photonic crystals, leading to complex and hierarchical geometries. In the first, we exposed the structures to mixtures of ethanol and water that partially wet their pores, where small adjustments to the ethanol content controlled the degree of partial wetting. In the second, we infiltrated the structures with thin films of volatile alkanes and observed a sequence of partial infiltration patterns as the liquid evaporated. In both cases, macroscopic symmetry breaking was driven by subtle sub-wavelength variations in the pore geometry that directed site-selective infiltration of liquids. The resulting patterns, well described by percolation theory, had significant effects on the photonic structures' optical properties, including the wavelength-dependence and angular dependence of scattering. Incorporating cross-linkable resins into our liquids, we were able create permanent photonic structures with these properties by freezing in place the filling patterns at arbitrary degrees of partial wetting and intermediate stages of drying. These techniques illustrate the versatility of interfacial phenomena in directing and tuning self-assembly of aperiodic structures.

physics.optics↗

arXiv2015

Condensation on Slippery Asymmetric Bumps

Bumps are omnipresent from human skin to the geological structures on planets, which offer distinct advantages in numerous phenomena including structural color, drag reduction, and extreme wettability. Although the topographical parameters of bumps such as radius of curvature of convex regions significantly influence various phenomena including anti-reflective structures and contact time of impacting droplets, the effect of the detailed bump topography on growth and transport of condensates have not been clearly understood. Inspired by the millimetric bumps of the Namib Desert beetle, here we report the identified role of radius of curvature and width of bumps with homogeneous surface wettability in growth rate, coalescence and transport of water droplets. Further rational design of asymmetric convex topography and synergetic combination with slippery coating simultaneously enable self-transport, leading to unseen five-fold higher growth rate and an order of magnitude faster shedding time of droplets compared to superhydrophobic surfaces. We envision that our fundamental understanding and innovative design of bumps can be applied to lead enhanced performance in various phase change applications including water harvesting.

physics.flu-dyn↗

arXiv2014

Dynamics of evaporative colloidal patterning

Drying suspensions often leave behind complex patterns of particulates, as might be seen in the coffee stains on a table. Here we consider the dynamics of periodic band or uniform solid film formation on a vertical plate suspended partially in a drying colloidal solution. Direct observations allow us to visualize the dynamics of the band and film deposition, and the transition in between when the colloidal concentration is varied. A minimal theory of the liquid meniscus motion along the plate reveals the dynamics of the banding and its transition to the filming as a function of the ratio of deposition and evaporation rates. We also provide a complementary multiphase model of colloids dissolved in the liquid, which couples the inhomogeneous evaporation at the evolving meniscus to the fluid and particulate flows and the transition from a dilute suspension to a porous plug. This allows us to determine the concentration dependence of the bandwidth and the deposition rate. Together, our findings allow for the control of drying-induced patterning as a function of the colloidal concentration and evaporation rate.

cond-mat.soft↗

arXiv2014

Elastocapillary coalescence of plates and pillars

When a fluid-immersed array of lamellae or filaments that is attached to a substrate is dried, evaporation leads to the formation of menisci on the tips of the plates or pillars that bring them together. Similarly, when hair dries it clumps together due to capillary forces induced by the liquid menisci between the flexible hairs. Building on prior experimental observations, we use a combination of theory and computation to understand the nature of this instability and its evolution in both the two-dimensional and three-dimensional setting of the problem. For the case of lamellae, we explicitly derive the interaction torques based on the relevant physical parameters. A Bloch-wave analysis for our periodic mechanical system captures the critical volume of the liquid and the 2-plate-collapse eigenmode at the onset of instability. We study the evolution of clusters and their arrest using numerical simulations to explain the hierarchical cluster formation and characterize the sensitive dependence of the final structures on the initial perturbations. We then generalize our analysis to treat the problem of pillar collapse in 3D, where the fluid domain is completely connected and the interface is a surface with the uniform mean curvature. Our theory and simulations capture the salient features of both previous experimental observations and our own in terms of the key parameters that can be used to control the kinetics of the process.

cond-mat.soft↗

arXiv2014

Hierarchical structural control of visual properties in self-assembled photonic-plasmonic pigments

We present a simple one-pot co-assembly method for the synthesis of hierarchically structured pigment particles consisting of silica inverse-opal bricks that are doped with plasmonic absorbers. We study the interplay between the plasmonic and photonic resonances and their effect on the visual appearance of macroscopic collections of photonic bricks that are distributed in randomized orientations. Manipulating the pore geometry tunes the wavelength- and angle-dependence of the scattering profile, which can be engineered to produce angle-dependent Bragg resonances that can either enhance or contrast with the color produced by the plasmonic absorber. By controlling the overall dimensions of the photonic bricks and their aspect ratios, their preferential alignment can either be encouraged or suppressed. This causes the Bragg resonance to appear either as uniform color travel in the former case or as sparse iridescent sparkle in the later case. By manipulating the surface chemistry of these photonic bricks, which introduces a fourth length-scale of independent tuning into our design, we can further engineer interactions between liquids and the pores. This allows the structural color to be maintained in oil-based formulations, and enables the creation of dynamic liquid-responsive images from the pigment.

physics.optics↗

arXiv2012

Creating bio-inspired hierarchical 3D-2D photonic stacks via planar lithography on self-assembled inverse opals

Structural hierarchy and complex 3D architecture are characteristics of biological photonic designs that are challenging to reproduce in synthetic materials. Top-down lithography allows for designer patterning of arbitrary shapes, but is largely restricted to planar 2D structures. Self-assembly techniques facilitate easy fabrication of 3D photonic crystals, but controllable defect-integration is difficult. In this paper we combine the advantages of top-down and bottom-up fabrication, developing two techniques to deposit 2D-lithographically-patterned planar layers on top of or in between inverse-opal 3D photonic crystals and creating hierarchical structures that resemble the architecture of the bright green wing scales of the butterfly, Parides sesostris. These fabrication procedures, combining advantages of both top-down and bottom-up fabrication, may prove useful in the development of omnidirectional coloration elements and 3D-2D photonic crystal devices.

physics.optics↗