arXiv subjects

Johannes Dickmann

Publications and source records attributed to Johannes Dickmann.

9 recordsLinked to original sources

arXiv2025

Guidelines for designs for ultrastable laser with $\mathbf{10^{-17}}$ fractional frequency instability

Lasers with long coherence time and narrow linewidth are an essential tool for quantum sensors and clocks. Ultrastable cavities and laser systems are now commercially available with fractional frequency instabilities in the mid $10^{-16}$ range. This document aims to provide technical guidance for researchers starting in the field of ultrastable lasers and to give an outlook toward the next generation of improved ultrastable lasers. These guidelines have arisen from the scope of the EMPIR project ``Next generation ultrastable lasers'' ( https://www.ptb.de/empir2021/nextlasers ) with contributions from the European project partners.

physics.optics↗

arXiv2024

Temperature-dependent mechanical losses of Eu$^{3+}$:Y$_{2}$SiO$_{5}$ for spectral hole burning laser stabilization

We investigate the mechanical loss characteristics of Eu$^{3+}$:Y$_2$SiO$_5$$\unicode{x2013}$a promising candidate for ultra-low-noise frequency stabilization through the spectral hole burning technique. Three different mechanical oscillators with varying surface-to-volume ratios and crystal orientations are evaluated. In this context, we perform mechanical ringdown and spectral measurements spanning temperatures from room temperature down to $15\,\mathrm{K}$. By doing so, we measure a maximum mechanical quality factor of $Q=3676$, corresponding to a loss angle of $ϕ=2.72\times 10^{-4}$. For a spectral hole burning laser stabilization experiment at $300\,\mathrm{mK}$, we can estimate the Allan deviation of the fractional frequency instability due to Brownian thermal noise to be below $σ_{δν/ν_0} = 2.5\times 10^{-18}$, a value lower than the estimated thermal-noise limit of any current cavity-referenced ultra-stable laser experiment.

physics.optics↗

arXiv2023

Using gravitational light deflection in optical cavities for laser frequency stabilization

We theoretically investigate the propagation of light in the presence of a homogeneous gravitational field. To model this, we derive the solutions of the wave equation in Rindler spacetime, which account for gravitational redshift and light deflection. The developed theoretical framework is used to explore the propagation of plane light waves in a horizontal Fabry-Perot cavity. We pay particular attention to the cavity output power. It is shown that this power depends not only on the input frequency, but also on the vertical position of a detector. We state that the height-dependent detector signal arising from the cavity internal light deflection effect (CILD-effect) also opens a new alternative way to frequency stabilization in Earth-based laser experiments and to study gravitational light deflection at laboratory scales.

gr-qc↗

arXiv2021

Impact of Earth's gravity on Gaussian beam propagation in hemispherical cavities

We theoretically investigate the influence of gravity on laser light in a hemispherical optical cavity, operating on Earth. The propagation of light in such a cavity is modeled by a Gaussian beam, affected by the Earth's gravitational field. On laboratory scale, this field is described by the spacetime of homogeneous gravity, known as Rindler spacetime. In that spacetime, the beam is bent downwards and acquires a height dependent phase shift. As a consequence the phase fronts of the laser light differ from those of a usual Gaussian beam. Assuming that the initial beam enters the cavity along its symmetry axis, these gravitational effects cause variations of the beam phase with every cavity round trip. Detailed calculations are performed to investigate how these phase variations depend on the beam parameters and the cavity setup. Moreover, we discuss the implications of our findings for cavity calibration techniques and cavity-based laser stabilization procedures.

gr-qc↗

arXiv2020

Gravitational light deflection in Earth-based laser cavity experiments

As known from Einstein's theory of general relativity, the propagation of light in the presence of a massive object is affected by gravity. In this work, we discuss whether the effect of gravitational light bending can be observed in Earth-based experiments, using high-finesse optical cavities. In order to do this, we theoretically investigate the dynamics of electromagnetic waves in the spacetime of a homogeneous gravitational field and give an analytical expression for the resulting modifications to Gaussian beam propagation. This theoretical framework is used to calculate the intensity profile at the output of a Fabry-Pérot cavity and to estimate the imprints of Earth's gravity on the cavity output signal. In particular, we found that gravity causes an asymmetry of the output intensity profile. Based on that, we discuss a measurement scheme, that could be realized in facilities like the GEO600 gravitational wave detector and the AEI 10 m detector prototype.

gr-qc↗

arXiv2019

Key signal contributions in photothermal deflection spectroscopy

We report on key signal contributions in photothermal deflection spectroscopy (PDS) of semiconductors at photon energies below the bandgap energy and show how to extract the actual absorption properties from the measurement data. To this end, we establish a rigorous computation scheme for the deflection signal including semi-analytic raytracing to analyze the underlying physical effects. The computation takes into account linear and nonlinear absorption processes affecting the refractive index and thus leading to a deflection of the probe beam. We find that beside the linear mirage effect, nonlinear absorption mechanisms make a substantial contribution to the signal for strongly focussed pump beams and sample materials with high two-photon absorption coefficients. For example, the measured quadratic absorption contribution exceeds 5% at a pump beam intensity of about ${1.3}\times{10^{5}}\;{W}/{cm^{2}}$ in Si and at ${5}\times{10^{4}}\;{W}/{cm^{2}}$ in GaAs. In addition, our method also includes thermal expansion effects as well as spatial gradients of the attenuation properties. We demonstrate that these effects result in an additional deflection contribution which substantially depends on the distance of the photodetector from the readout point. This distance dependent contribution enhances the surface related PDS signal up to two orders of magnitude and may be misinterpreted as surface absorption if not corrected in the analysis of the measurement data. We verify these findings by PDS measurements on crystalline silicon at a wavelength of 1550 nm and provide guidelines how to extract the actual attenuation coefficient from the PDS signal.

cond-mat.mtrl-sci↗

arXiv2018

Thermal noise of beam splitters in laser gravitational wave detectors

We present the calculation of thermal noise in interferometric gravitational-wave detectors due to the thermal fluctuations of the beam splitter (BS). This work makes use of a recently developed method of the analysis of thermal noise in mirrors from first principles, based on the fluctuation dissipation theorem. The evaluation of BS thermal noise is carried out for the two different grav- itational wave observatories, GEO600 and the Advanced Laser Interferometer Gravitational Wave Observatory (aLIGO). The analysis evaluates thermal noise from both the substrate and the optical reflective and antireflective stacks located on the BS surface. We demonstrate that the fluctuations of both reflecting and anti-reflecting surfaces significantly contribute to the total thermal noise of the BS. The oscillating intensity pattern couples small-scale distortions of the surface to the overall phase readout, and therefore increases the overall thermal noise. In the case of aLIGO, the BS contribution is with $0.3\%$ negligibly small. At a frequency of 500Hz, the BS causes about $10\%$ of GEO600's sensitivity limit. BS noise impairs the feasible sensitivity of the GEO-HF design proposal by about $50\%$.

astro-ph.IM↗

arXiv2018

Highly reflective low-noise etalon-based meta-mirror

We present a concept of a mirror for the application in high-reflectivity low-noise instruments such as interferometers. The concept is based on an etalon with a metasurface (meta-etalon) on the front and a conventional multilayer stack on the rear surface. The etalon in combination with the metasurface enables a dedicated spatial weighing of the relevant thermal noise processes and by this a substantial reduction of the overall read out thermal noise. We exemplary illustrate the benefit of the proposed etalon for thermal noise in two applications: The test masses of the Einstein Telescope gravitational wave detector and a single-crystalline cavity for laser frequency stabilization. In the Einstein Telescope the thermal noise of the etalon even at room temperature outperforms existing concepts for operation temperatures at 10K. For the laser stabilization cavity, a reduction of the modified Allan deviation of an order of magnitude is predicted.

physics.ins-det↗

arXiv2018

Thermal noise in complex systems

We present a method to calculate the power spectral density of Brownian noise in complex optomechanical systems using Levin's approach of virtual pressure and present first mechanical loss measurements for high-purity GaAs over a wide temperature range from 7 K to 250 K. The loss reveals three Debye loss peaks. Each peak corresponds to an Arrhenius-like relaxation process with activation energies of 17.9 meV, 65.4 meV and 123 meV respectively. Additional light induced damping was observed for photon energies below and above the fundamental gap of GaAs in contrast to observations by Okamoto et al.

physics.app-ph↗