arXiv subjects

Jorge Angeles

Publications and source records attributed to Jorge Angeles.

14 recordsLinked to original sources

arXiv2011

The Design of a Novel Prismatic Drive for a Three-DOF Parallel-Kinematics Machine

The design of a novel prismatic drive is reported in this paper. This transmission is based on Slide-o-Cam, a cam mechanism with multiple rollers mounted on a common translating follower. The design of Slide-o-Cam was reported elsewhere. This drive thus provides pure-rolling motion, thereby reducing the friction of rack-and-pinions and linear drives. Such properties can be used to design new transmissions for parallel-kinematics machines. In this paper, this transmission is intended to replace the ball-screws in Orthoglide, a three-dof parallel robot intended for machining applications.

cs.RO↗

arXiv2007

The Isoconditioning Loci of Planar Three-DOF Parallel Manipulators

The subject of this paper is a special class of three-degree-of-freedom parallel manipulators. The singular configurations of the two Jacobian matrices are first studied. The isotropic configurations are then found based on the characteristic length of this manipulator. The isoconditioning loci for the Jacobian matrices are plotted to define a global performance index allowing the comparison of the different working modes. The index thus resulting is compared with the Cartesian workspace surface and the average of the condition number.

cs.RO↗

arXiv2007

The Computation of All 4R Serial Spherical Wrists With an Isotropic Architecture

A spherical wrist of the serial type is said to be isotropic if it can attain a posture whereby the singular values of its Jacobian matrix are all identical and nonzero. What isotropy brings about is robustness to manufacturing, assembly, and measurement errors, thereby guaranteeing a maximum orientation accuracy. In this paper we investigate the existence of redundant isotropic architectures, which should add to the dexterity of the wrist under design by virtue of its extra degree of freedom. The problem formulation leads to a system of eight quadratic equations with eight unknowns. The Bezout number of this system is thus 2^8 = 256, its BKK bound being 192. However, the actual number of solutions is shown to be 32. We list all solutions of the foregoing algebraic problem. All these solutions are real, but distinct solutions do not necessarily lead to distinct manipulators. Upon discarding those algebraic solutions that yield no new wrists, we end up with exactly eight distinct architectures, the eight corresponding manipulators being displayed at their isotropic posture.

cs.RO↗

arXiv2007

The Computation of All 4R Serial Spherical Wrists With an Isotropic Architecture

A spherical wrist of the serial type with n revolute (R) joints is said to be isotropic if it can attain a posture whereby the singular values of its Jacobian matrix are all equal to sqrt(n/3). What isotropy brings about is robustness to manufacturing, assembly, and measurement errors, thereby guaranteeing a maximum orientation accuracy. In this paper we investigate the existence of redundant isotropic architectures, which should add to the dexterity of the wrist under design by virtue of its extra degree of freedom. The problem formulation, for, leads to a system of eight quadratic equations with eight unknowns. The Bezout number of this system is thus 2^8=256, its BKK bound being 192. However, the actual number of solutions is shown to be 32. We list all solutions of the foregoing algebraic problem. All these solutions are real, but distinct solutions do not necessarily lead to distinct manipulators. Upon discarding those algebraic solutions that yield no new wrists, we end up with exactly eight distinct architectures, the eight corresponding manipulators being displayed at their isotropic postures.

cs.RO↗

arXiv2007

The Isoconditioning Loci of A Class of Closed-Chain Manipulators

The subject of this paper is a special class of closed-chain manipulators. First, we analyze a family of two-degree-of-freedom (dof) five-bar planar linkages. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the ``inverse kinematics" and the "direct kinematics" matrices. It is shown that the loci of points of the workspace where the condition number of the direct-kinematics matrix remains constant, i.e., the isoconditioning loci, are the coupler points of the four-bar linkage obtained upon locking the middle joint of the linkage. Furthermore, if the line of centers of the two actuated revolutes is used as the axis of a third actuated revolute, then a three-dof hybrid manipulator is obtained. The isoconditioning loci of this manipulator are surfaces of revolution generated by the isoconditioning curves of the two-dof manipulator, whose axis of symmetry is that of the third actuated revolute.

cs.RO↗

arXiv2007

Conception Isotropique D'Une Morphologie ParallÈle : Application à L'Usinage

The aim of this paper is the isotropic design of a hybrid morphology dedicated to 3-axis machining applications. It is necessary to ensure the feasibility of continuous, singularity-free trajectories, as well as a good manipulability in position and velocity. We want to propose an alternative design to conventional serial machine-tools. We compare a serial PPP machine-tool (three prismatic orthogonal axes) with a hybrid architecture which we optimize only the first two axes. The critrerion used for the optimization is the conditioning of the Jacobian matrices. The optimum, namely isotropy, can be obtained which provides our architecture with excellent manipulability properties.

cs.RO↗

arXiv2007

The Kinematics of Manipulators Built From Closed Planar Mechanisms

The paper discusses the kinematics of manipulators builts of planar closed kinematic chains. A special kinematic scheme is extracted from the array of these mechanisms that looks the most promising for the creation of different types of robotic manipulators. The structural features of this manipulator determine a number of its original properties that essentially simplify its control. These features allow the main control problems to be effectively overcome by application of the simple kinematic problems. The workspace and singular configurations of a basic planar manipulator are studied. By using a graphic simulation method, motions of the designed mechanism are examined. A prototype of this mechanism was implemented to verify the proposed approach.

cs.RO↗

arXiv2007

The Design of a Novel Prismatic Drive for a Three-DOF Parallel-Kinematics Machine

The design of a novel prismatic drive is reported in this paper. This transmission is based on Slide-O-Cam, a cam mechanism with multiple rollers mounted on a common translating follower. The design of Slide-O-Cam was reported elsewhere. This drive thus provides pure-rolling motion, thereby reducing the friction of rack-and-pinions and linear drives. Such properties can be used to design new transmissions for parallel-kinematics machines. In this paper, this transmission is optimized to replace ball-screws in Orthoglide, a three-DOF parallel robot optimized for machining applications.

cs.RO↗

arXiv2007

The Isoconditioning Loci of Planar Three-DOF Parallel Manipulators

The subject of this paper is a special class of parallel manipulators. First, we analyze a family of three-degree-of-freedom manipulators. Two Jacobian matrices appear in the kinematic relations between the joint-rate and the Cartesian-velocity vectors, which are called the "inverse kinematics" and the "direct kinematics" matrices. The singular configurations of these matrices are studied. The isotropic configurations are then studied based on the characteristic length of this manipulator. The isoconditioning loci of all Jacobian matrices are computed to define a global performance index to compare the different working modes.

cs.RO↗

arXiv2007

Strategies for the Design of a Slide-o-Cam Transmission

The optimization of the pressure angle in a cam-follower transmission is reported in this paper. This transmission is based on Slide-o-Cam, a cam mechanism with multiple rollers mounted on a common translating follower. The design of Slide-o-Cam, a transmission intended to produce a sliding motion from a turning drive, or vice versa, was reported elsewhere. This transmission provides pure-rolling motion, thereby reducing the friction of rack-and-pinions and linear drives. The pressure angle is a suitable performance index for this transmission because it determines the amount of force transmitted to the load vs. that transmitted to the machine frame. Two alternative design strategies are studied, namely, (i) increase the number of lobes on each cam or (ii) increase the number of cams. This device is intended to replace the current ball-screws in Orthoglide, a three-DOF parallel robot for the production of translational motions, currently under development at Ecole Centrale de Nantes for machining applications.

cs.RO↗

arXiv2007

On the Kinetostatic Optimization of Revolute-Coupled Planar Manipulators

Proposed in this paper is a kinetostatic performance index for the optimum dimensioning of planar manipulators of the serial type. The index is based on the concept of distance of the underlying Jacobian matrix to a given isotropic matrix that is used as a reference model for purposes of performance evaluation. Applications of the index fall in the realm of design, but control applications are outlined. The paper focuses on planar manipulators, the basic concepts being currently extended to their three-dimensional counterparts.

cs.RO↗

arXiv2007

The Multiobjective Optimization of a Prismatic Drive

The multiobjective optimization of Slide-o-Cam is reported in this paper. Slide-o-Cam is a cam mechanism with multiple rollers mounted on a common translating follower. This transmission provides pure-rolling motion, thereby reducing the friction of rack-and-pinions and linear drives. A Pareto frontier is obtained by means of multiobjective optimization. This optimization is based on three objective functions: (i) the pressure angle, which is a suitable performance index for the transmission because it determines the amount of force transmitted to the load vs. that transmitted to the machine frame; (ii) the Hertz pressure used to evaluate the stresses produced on the contact surface between cam and roller; and (iii) the size of the mechanism, characterized by the number of cams and their width.

cs.RO↗

arXiv2007

On Isotropic Sets of Points in the Plane. Application to the Design of Robot Archirectures

Various performance indices are used for the design of serial manipulators. One method of optimization relies on the condition number of the Jacobian matrix. The minimization of the condition number leads, under certain conditions, to isotropic configurations, for which the roundoff-error amplification is lowest. In this paper, the isotropy conditions, introduced elsewhere, are the motivation behind the introduction of isotropic sets of points. By connecting together these points, we define families of isotropic manipulators. This paper is devoted to planar manipulators, the concepts being currently extended to their spatial counterparts. Furthermore, only manipulators with revolute joints are considered here.

cs.RO↗

arXiv2007

The Kinematic design of a 3-dof Hybrid Manipulator

This paper focuses on the kinematic properties of a new three-degree-of-freedom hybrid manipulator. This manipulator is obtained by adding in series to a five-bar planar mechanism (similar to the one studied by Bajpai and Roth) a third revolute passing through the line of centers of the two actuated revolute joints of the above linkage. The resulting architecture is hybrid in that it has both serial and parallel links. Fully-parallel manipulators are known for the existence of particularly undesirable singularities (referred to as parallel singularities) where control is lost [4] and [6]. On the other hand, due to their cantilever type of kinematic arrangement, fully serial manipulators suffer from a lack of stiffness and from relatively large positioning errors. The hybrid manipulator studied is intrinsically stiffer and more accurate. Furthermore, since all actuators are located on the first axis, the inertial effects are considerably reduced. In addition, it is shown that the special kinematic structure of our manipulator has the potential of avoiding parallel singularities by a suitable choice of the "working mode", thus leading to larger workspaces. The influence of the different structural dimensions (e.g. the link lengths) on the kinematic and mechanical properties are analysed in view of the optimal design of such hybrid manipulators.

cs.RO↗