arXiv subjects

Jorge Querol

Publications and source records attributed to Jorge Querol.

35 records · Page 2Linked to original sources

arXiv2024

Performance Evaluation of Neuromorphic Hardware for Onboard Satellite Communication Applications

Spiking neural networks (SNNs) implemented on neuromorphic processors (NPs) can enhance the energy efficiency of deployments of artificial intelligence (AI) for specific workloads. As such, NP represents an interesting opportunity for implementing AI tasks on board power-limited satellite communication spacecraft. In this article, we disseminate the findings of a recently completed study which targeted the comparison in terms of performance and power-consumption of different satellite communication use cases implemented on standard AI accelerators and on NPs. In particular, the article describes three prominent use cases, namely payload resource optimization, onboard interference detection and classification, and dynamic receive beamforming; and compare the performance of conventional convolutional neural networks (CNNs) implemented on Xilinx's VCK5000 Versal development card and SNNs on Intel's neuromorphic chip Loihi 2.

eess.SP↗

arXiv2023

Supervised Learning Based Real-Time Adaptive Beamforming On-board Multibeam Satellites

Satellite communications (SatCom) are crucial for global connectivity, especially in the era of emerging technologies like 6G and narrowing the digital divide. Traditional SatCom systems struggle with efficient resource management due to static multibeam configurations, hindering quality of service (QoS) amidst dynamic traffic demands. This paper introduces an innovative solution - real-time adaptive beamforming on multibeam satellites with software-defined payloads in geostationary orbit (GEO). Utilizing a Direct Radiating Array (DRA) with circular polarization in the 17.7 - 20.2 GHz band, the paper outlines DRA design and a supervised learning-based algorithm for on-board beamforming. This adaptive approach not only meets precise beam projection needs but also dynamically adjusts beamwidth, minimizes sidelobe levels (SLL), and optimizes effective isotropic radiated power (EIRP).

eess.SP↗

arXiv2023

Genetic Algorithm-based Beamforming in Subarray Architectures for GEO Satellites

The incorporation of subarrays in Direct Radiating Arrays for satellite missions is fundamental in reducing the number of Radio Frequency chains, which correspondingly diminishes cost, power consumption, space, and mass. Despite the advantages, previous beamforming schemes incur significant losses during beam scanning, particularly when hybrid beamforming is not employed. Consequently, this paper introduces an algorithm capable of compensating for these losses by increasing the power, for this, the algorithm will activate radiating elements required to address a specific Effective Isotropic Radiated Power for a beam pattern over Earth, projected from a GeoStationary satellite. In addition to the aforementioned compensation, other beam parameters have been addressed in the algorithm, such as beamwidth and Side Lobe Levels. To achieve these objectives, we propose employing the array thinning concept through the use of genetic algorithms, which enable beam shaping with the desired characteristics and power. The full array design considers an open-ended waveguide, configured to operate in circular polarization within the Ka-band frequency range of 17.7-20.2 GHz.

eess.SY↗

arXiv2023

Flexible Payload Configuration for Satellites using Machine Learning

Satellite communications, essential for modern connectivity, extend access to maritime, aeronautical, and remote areas where terrestrial networks are unfeasible. Current GEO systems distribute power and bandwidth uniformly across beams using multi-beam footprints with fractional frequency reuse. However, recent research reveals the limitations of this approach in heterogeneous traffic scenarios, leading to inefficiencies. To address this, this paper presents a machine learning (ML)-based approach to Radio Resource Management (RRM). We treat the RRM task as a regression ML problem, integrating RRM objectives and constraints into the loss function that the ML algorithm aims at minimizing. Moreover, we introduce a context-aware ML metric that evaluates the ML model's performance but also considers the impact of its resource allocation decisions on the overall performance of the communication system.

cs.LG↗

arXiv2023

ML-based PBCH symbol detection and equalization for 5G Non-Terrestrial Networks

This paper delves into the application of Machine Learning (ML) techniques in the realm of 5G Non-Terrestrial Networks (5G-NTN), particularly focusing on symbol detection and equalization for the Physical Broadcast Channel (PBCH). As 5G-NTN gains prominence within the 3GPP ecosystem, ML offers significant potential to enhance wireless communication performance. To investigate these possibilities, we present ML-based models trained with both synthetic and real data from a real 5G over-the-satellite testbed. Our analysis includes examining the performance of these models under various Signal-to-Noise Ratio (SNR) scenarios and evaluating their effectiveness in symbol enhancement and channel equalization tasks. The results highlight the ML performance in controlled settings and their adaptability to real-world challenges, shedding light on the potential benefits of the application of ML in 5G-NTN.

eess.SP↗

arXiv2023

Harnessing Supervised Learning for Adaptive Beamforming in Multibeam Satellite Systems

In today's ever-connected world, the demand for fast and widespread connectivity is insatiable, making multibeam satellite systems an indispensable pillar of modern telecommunications infrastructure. However, the evolving communication landscape necessitates a high degree of adaptability. This adaptability is particularly crucial for beamforming, as it enables the adjustment of peak throughput and beamwidth to meet fluctuating traffic demands by varying the beamwidth, side lobe level (SLL), and effective isotropic radiated power (EIRP). This paper introduces an innovative approach rooted in supervised learning to efficiently derive the requisite beamforming matrix, aligning it with system requirements. Significantly reducing computation time, this method is uniquely tailored for real-time adaptation, enhancing the agility and responsiveness of satellite multibeam systems. Exploiting the power of supervised learning, this research enables multibeam satellites to respond quickly and intelligently to changing communication needs, ultimately ensuring uninterrupted and optimized connectivity in a dynamic world.

eess.SY↗

arXiv2023

Signal Processing Based Antenna Pattern Characterization for MIMO Systems

Sophisticated antenna technologies are constantly evolving to meet the escalating data demands projected for 6G and future networks. The characterization of these emerging antenna systems poses challenges that necessitate a reevaluation of conventional techniques, which rely solely on simple measurements conducted in advanced anechoic chambers. In this study, our objective is to introduce a novel endeavour for antenna pattern characterization (APC) in next-generation multiple-input-multiple-output (MIMO) systems by utilizing the potential of signal processing tools. In contrast to traditional methods that struggle with multi-path scenarios and require specialized equipment for measurements, we endeavour to estimate the antenna pattern by exploiting information from both line-of-sight (LoS) and non-LoS contributions. This approach enables antenna pattern characterization in complex environments without the need for anechoic chambers, resulting in substantial cost savings. Furthermore, it grants a much wider research community the ability to independently perform APC for emerging complex 6G antenna systems, without relying on anechoic chambers. Simulation results demonstrate the efficacy of the proposed novel approach in accurately estimating the true antenna pattern.

eess.SP↗

arXiv2023

Adaptive Timers and Buffer Optimization for Layer-2 Protocols in 5G Non-Terrestrial Networks

Interest in the integration of Terrestrial Networks (TN) and Non-Terrestrial Networks (NTN); primarily satellites; has been rekindled due to the potential of NTN to provide ubiquitous coverage. Especially with the peculiar and flexible physical layer properties of 5G-NR, now direct access to 5G services through satellites could become possible. However, the large Round-Trip Delays (RTD) in NTNs require a re-evaluation of the design of RLC and PDCP layers timers ( and associated buffers), in particular for the regenerative payload satellites which have limited computational resources, and hence need to be optimally utilized. Our aim in this work is to initiate a new line of research for emerging NTNs with limited resources from a higher-layer perspective. To this end, we propose a novel and efficient method for optimally designing the RLC and PDCP layers' buffers and timers without the need for intensive computations. This approach is relevant for low-cost satellites, which have limited computational and energy resources. The simulation results show that the proposed methods can significantly improve the performance in terms of resource utilization and delays.

cs.NI↗

arXiv2023

IRS Assisted MIMO Full Duplex: Rate Analysis and Beamforming Under Imperfect CSI

Intelligent reflecting surfaces (IRS) have emerged as a promising technology to enhance the performance of wireless communication systems. By actively manipulating the wireless propagation environment, IRS enables efficient signal transmission and reception. In recent years, the integration of IRS with full-duplex (FD) communication has garnered significant attention due to its potential to further improve spectral and energy efficiencies. IRS-assisted FD systems combine the benefits of both IRS and FD technologies, providing a powerful solution for the next generation of cellular systems. In this manuscript, we present a novel approach to jointly optimize active and passive beamforming in a multiple-input-multiple-output (MIMO) FD system assisted by an IRS for weighted sum rate (WSR) maximization. Given the inherent difficulty in obtaining perfect channel state information (CSI) in practical scenarios, we consider imperfect CSI and propose a statistically robust beamforming strategy to maximize the ergodic WSR. Additionally, we analyze the achievable WSR for an IRS-assisted MIMO FD system under imperfect CSI by deriving both the lower and upper bounds. To tackle the problem of ergodic WSR maximization, we employ the concept of expected weighted minimum mean squared error (EWMMSE), which exploits the information of the expected error covariance matrices and ensures convergence to a local optimum. We evaluate the effectiveness of our proposed design through extensive simulations. The results demonstrate that our robust approach yields significant performance improvements compared to the simplistic beamforming approach that disregards CSI errors, while also outperforming the robust half-duplex (HD) system considerably

eess.SP↗

arXiv2023

Robust Beamforming for IRS Aided MIMO Full Duplex Systems

In this paper, a novel robust beamforming for an intelligent reflecting surface (IRS) assisted FD system is presented. Since perfect channel state information (CSI) is often challenging to acquire in practice, we consider the case of imperfect CSI and adopt a statistically robust beamforming approach to maximize the ergodic weighted sum rate (WSR). We also analyze the achievable WSR of an IRS-assisted FD with imperfect CSI, for which the lower and the upper bounds are derived. The ergodic WSR maximization problem is tackled based on the expected Weighted Minimum Mean Squared Error (WMMSE), which is guaranteed to converge to a local optimum. The effectiveness of the proposed design is investigated with extensive simulation results. It is shown that our robust design achieves significant performance gain compared to the naive beamforming approaches and considerably outperforms the robust Half-Duplex (HD) system.

eess.SP↗

arXiv2023

Full-Duplex-Enabled Joint Communications and Sensing with Reconfigurable Intelligent Surfaces

The full-duplex (FD) technology has the potential to radically evolve wireless systems, facilitating the integration of both communications and radar functionalities into a single device, thus, enabling joint communication and sensing (JCAS). In this paper, we present a novel approach for JCAS that incorporates a reconfigurable intelligent surface (RIS) in the near-field of an FD multiple-input multiple-output (MIMO) node, which is jointly optimized with the digital beamformers to enable JSAC and efficiently handle self-interference (SI). We propose a novel problem formulation for FD MIMO JCAS systems to jointly minimize the total received power at the FD node's radar receiver while maximizing the sum rate of downlink communications subject to a Cramér-Rao bound (CRB) constraint. In contrast to the typically used CRB in the relevant literature, we derive a novel, more accurate, target estimation bound that fully takes into account the RIS deployment. The considered problem is solved using alternating optimization, which is guaranteed to converge to a local optimum. The simulation results demonstrate that the proposed scheme achieves significant performance improvement both for communications and sensing. It is showcased that, jointly designing the FD MIMO beamformers and the RIS phase configuration to be SI aware can significantly loosen the requirement for additional SI cancellation.

cs.IT↗

arXiv2023

Parallel and Distributed Hybrid Beamforming for Multicell Millimeter Wave MIMO Full Duplex

Full duplex (FD) is an auspicious wireless technology that holds the potential to double data rates through simultaneous transmission and reception. This paper proposes two innovative designs of hybrid beamforming (HYBF) for a multicell massive multiple-input-multiple-output (mMIMO) millimeter wave (mmWave) FD system. Initially, we introduce a novel centralized HYBF (C-HYBF) scheme, which employs the minorization-maximization (MM) method. However, while centralized beamforming designs offer superior performance, they suffer from high computational complexity, substantial communication overhead, and demand expensive computational resources. To surmount these challenges, we present a framework that facilitates per-link parallel and distributed HYBF (P&D- HYBF) in the mmWave frequency band. This cooperative approach enables each base station (BS) to independently solve its local, low-complexity sub-problems in parallel, resulting in a substantial reduction in communication overhead and computational complexity. Simulation results demonstrate that P&D-HYBF achieves comparable performance to C-HYBF, and with only a few radio-frequency (RF) chains, both designs surpass the capabilities of fully digital half duplex (HD) systems.

cs.IT↗

arXiv2022

Non-Coherent Massive MIMO Integration in Satellite Communication

Massive Multiple Input-Multiple Output (mMIMO) technique has been considered an efficient standard to improve the transmission rate significantly for the following wireless communication systems, such as 5G and beyond. However, implementing this technology has been facing a critical issue of acquiring much channel state information. Primarily, this problem becomes more criticising in the integrated satellite and terrestrial networks (3GPP-Release 15) due to the countable high transmission delay. To deal with this challenging problem, the mMIMO-empowered non-coherent technique can be a promising solution. To our best knowledge, this paper is the first work considering employing the non-coherent mMIMO in satellite communication systems. This work aims to analyse the challenges and opportunities emerging with this integration. Moreover, we identified the issues in this conjunction. The preliminary results presented in this work show that the performance measured in bit error rate (BER) and the number of antennas are not far from that required for terrestrial links. Furthermore, thanks to mMIMO in conjunction with the non-coherent approach, we can work in a low signal-to-noise ratio (SNR) regime, which is an excellent advantage for satellite links.

cs.IT↗

arXiv2022

Architectures and Synchronization Techniques for Distributed Satellite Systems: A Survey

Cohesive Distributed Satellite Systems (CDSS) is a key enabling technology for the future of remote sensing and communication missions. However, they have to meet strict synchronization requirements before their use is generalized. When clock or local oscillator signals are generated locally at each of the distributed nodes, achieving exact synchronization in absolute phase, frequency, and time is a complex problem. In addition, satellite systems have significant resource constraints, especially for small satellites, which are envisioned to be part of the future CDSS. Thus, the development of precise, robust, and resource-efficient synchronization techniques is essential for the advancement of future CDSS. In this context, this survey aims to summarize and categorize the most relevant results on synchronization techniques for DSS. First, some important architecture and system concepts are defined. Then, the synchronization methods reported in the literature are reviewed and categorized. This article also provides an extensive list of applications and examples of synchronization techniques for DSS in addition to the most significant advances in other operations closely related to synchronization, such as inter-satellite ranging and relative position. The survey also provides a discussion on emerging data-driven synchronization techniques based on ML. Finally, a compilation of current research activities and potential research topics is proposed, identifying problems and open challenges that can be useful for researchers in the field.

eess.SY↗

arXiv2021

End-to-end Precoding Validation over a Live GEO Satellite Forward Link

In this paper we demonstrate end-to-end precoded multi-user multiple-input single-output (MU-MISO) communications over a live GEO satellite link. Precoded communications enable full frequency reuse (FFR) schemes in satellite communications (SATCOM) to achieve broader service availability and higher spectrum efficiency than with the conventional four-color (4CR) and two-color (2CR) reuse approaches. In this scope, we develop an over-the-air test-bed for end-to-end precoding validations. We use an actual multi-beam satellite to transmit and receive precoded signals using the DVB-S2X standard based gateway and user terminals. The developed system is capable of end-to-end real-time communications over the satellite link including channel measurements and precompensation. It is shown, that by successfully canceling inter-user interference in the actual satellite FFR link precoding brings gains in terms of enhanced SINR and increased system goodput.

cs.IT↗

arXiv2020

A Remote Carrier Synchronization Technique for Coherent Distributed Remote Sensing Systems

Phase, frequency, and time synchronization are crucial requirements for many applications, such as multi-static remote sensing and communication systems. Moreover, the synchronization solution becomes even more challenging when the nodes are orbiting or flying on airborne or spaceborne platforms. This paper compares the available technologies used for the synchronization and coordination of nodes in distributed remote sensing applications. Additionally, this paper proposes a general system model and identifies preliminary guidelines and critical elements for implementing the synchronization mechanisms exploiting the inter-satellite communication link. The distributed phase synchronization loop introduced in this work deals with the self-interference in a full-duplex point to point scenario by transmitting two carriers at each node. All carriers appear with different frequency offsets around a central frequency, called the application central-frequency or the beamforming frequency. This work includes a detailed analysis of the proposed algorithm and the required simulations to verify its performance for different phase noise, AWGN, and Doppler shift scenarios.

eess.SP↗

arXiv2020

System Modelling and Design Aspects of Next Generation High Throughput Satellites

Future generation wireless networks are targeting the convergence of fixed, mobile and broadcasting systems with the integration of satellite and terrestrial systems towards utilizing their mutual benefits. Satellite Communications (Sat- Com) is envisioned to play a vital role to provide integrated services seamlessly over heterogeneous networks. As compared to terrestrial systems, the design of SatCom systems require a different approach due to differences in terms of wave propagation, operating frequency, antenna structures, interfering sources, limitations of onboard processing, power limitations and transceiver impairments. In this regard, this letter aims to identify and discuss important modeling and design aspects of the next generation High Throughput Satellite (HTS) systems. First, communication models of HTSs including the ones for multibeam and multicarrier satellites, multiple antenna techniques, and for SatCom payloads and antennas are highlighted and discussed. Subsequently, various design aspects of SatCom transceivers including impairments related to the transceiver, payload and channel, and traffic-based coverage adaptation are presented. Finally, some open topics for the design of next generation HTSs are identified and discussed.

eess.SP↗