arXiv subjects

Jun Ji

Publications and source records attributed to Jun Ji.

16 recordsLinked to original sources

arXiv2026

Nonlinear exceptional points in an integrated acoustic-wave oscillator for longwave infrared sensing

Exceptional points (EP) featuring enhanced responsivity and rich dynamics have attracted extensive attentions in device developments and sensing applications. However, it remains debated whether employing EP systems is beneficial in practical sensing applications. Here, we demonstrate that a nonlinear EP in our microwave-frequency acoustic-wave oscillator improves longwave infrared (LWIR) detection under practical conditions. By phase tuning the nonlinear gain, our detector can be operated at different conditions with respect to the nonlinear EP. Compared with operation away from EP, our detector at EP shows a 33-fold improvement in responsivity and an 8.75-fold extension of 3-dB bandwidth. We observe a 6-fold enhancement in signal-to-noise ratio at an input modulation frequency of 6.2 kHz. At the incident LWIR wavelength of 9.6 um, our detector at EP exhibits a noise equivalent power (NEP) of 310 pW*Hz^-1/2 at input frequency of 10 kHz, yielding a figure of merit, product of NEP and time constant, of 9.87*10^-3 pW*Hz^-3/2, a 10-fold improvement over operation away from EP. Our integrated acoustic devices offer a versatile platform for exploring noise dynamics and developing practical sensors that exploit non-Hermitian nonlinearities.

physics.optics↗

arXiv2026

Magnet-Free Nonreciprocal frequency conversion using Sequential Temporal modulation: Theory and Simulations

Nonreciprocal conversion is essential for protecting sources and enabling unidirectional signal routing in photonic, phononic, electronics, and quantum systems, yet conventional implementations rely on magnetic bias that could be challenging to integrate on chip. We propose a magnet-free scheme for frequency-domain nonreciprocity based on sequential, time-gated couplings in a three-mode system. By activating interactions in a fixed temporal order, the forward and reverse frequency conversion pathways acquire unequal dwell times in a lossy intermediate mode, producing strong nonreciprocity without requiring nonlinearities or magnetic materials. Using a harmonic-balance formulation and a Dyson-Born expansion, we derive a compact analytical expression for the isolation ratio that reveals the roles of Floquet sidebands, duty-cycle control, modulation frequency, and dissipation. The results are confirmed by direct time-domain simulations over a wide parameter range. From these results, we extract practical design rules for optimizing isolation through temporal sequencing, loss engineering, and modulation timing. The framework is general and directly applicable to integrated platforms in photonics, phononics, microwave electronics, and superconducting circuits.

physics.app-ph↗

arXiv2026

Low-loss phononic integrated circuits based on a silicon nitride-lithium niobate platform

Microwave-frequency acoustic waves in solids have emerged as a versatile platform for both classical and quantum applications. While phononic integrated devices and circuits are being developed on various material platforms, an ideal phononic integrated circuit (PnIC) platform should simultaneously support low-loss waveguide structures, high-quality-factor resonators, high-performance modulators, and efficient electromechanical transducers. Here, we establish a low-loss gigahertz-frequency PnIC platform based on patterned thin-film silicon nitride (SiN) on lithium niobate (LN) substrate. We develop low-loss PnIC building blocks including waveguides, directional couplers, and high-quality-factor (high-Q) ring resonators. As an application, we demonstrate a 1-GHz phononic oscillator based on a ring resonator, reaching a low phase noise of -159.0 dBc/Hz at a 100-kHz offset frequency. Our low-loss PnICs could meet the requirements in microwave acoustics, quantum phononics, and integrated hybrid systems combining phonons, photons, superconducting qubits, and solid-state defects.

physics.app-ph↗

arXiv2026

Resonance-enhanced integrated acousto-optic beam steering

Optical beam steering is a key technology for free-space optical communication, sensing, and imaging. Mechanical beam steering systems suffer from limited scanning speed and bulky form factors, while existing solid-state solutions rely on pixelated synthetic aperture that requires complex fabrication and control architectures. Integrated acousto-optic beam steering (AOBS) is an emerging technology that enables continuous one-dimensional beam steering using integrated acoustic transducers and fixed-wavelength laser sources. Here, we integrate AOBS with an optical ring resonator on the same thin-film lithium niobate (TFLN) platform to significantly enhance beam steering efficiency and system functionality. The resulting device achieves a resonance-enhanced beam steering efficiency of up to $26\%$ and a field of view of $18^\circ$. Moreover, by leveraging integrated electro-optic control, we dynamically lock the ring-resonator's resonance to a chirped laser frequency, enabling frequency-modulated continuous-wave (FMCW) LiDAR operation. By combining lithium niobate's piezoelectric and electro-optic properties, this work establishes a compact, efficient, and scalable beam-steering platform with co-integrated acousto-optic modulation and electro-optic control for multifunctional applications.

physics.app-ph↗

arXiv2025

Microwave-acoustic-based isolated gate driver for power electronics

Electrical isolation is critical to ensure safety and minimize electromagnetic interference (EMI), yet existing methods struggle to simultaneously transmit power and signals through a unified channel. Here we demonstrate a mechanically-isolated gate driver based on microwave-frequency surface acoustic wave (SAW) device on lithium niobate that achieves galvanic isolation of 2.75 kV with ultralow isolation capacitance (0.032 pF) over 1.25 mm mechanical propagation length, delivering 13.4 V open-circuit voltage and 44.4 mA short-circuit current. We demonstrate isolated gate driving for a gallium nitride (GaN) high-electron-mobility transistor, achieving a turn-on time of 108.8 ns comparable to commercial drivers and validate its operation in a buck converter. In addition, our SAW device operates over an ultrawide temperature range from 0.5 K (-272.6 {\deg}C) to 544 K (271 {\deg}C). The microwave-frequency SAW devices offer inherent EMI immunity and potential for heterogeneous integration on multiple semiconductor platforms, enabling compact, high-performance isolated power and signal transmission in advanced power electronics.

eess.SY↗

arXiv2025

On-chip cavity electro-acoustics using lithium niobate phononic crystal resonators

Mechanical systems are pivotal in quantum technologies because of their long coherent time and versatile coupling to qubit systems. So far, the coherent and dynamic control of gigahertz-frequency mechanical modes mostly relies on optomechanical coupling and piezoelectric coupling to superconducting qubits. Here, we demonstrate on-chip cavity electro-acoustic dynamics using our microwave-frequency electrically-modulated phononic-crystal (PnC) resonators on lithium niobate (LN). Leveraging the high dispersion of PnC, our phononic modes space unevenly in the frequency spectrum, emulating atomic energy levels. Atomic-like transitions between different phononic modes are achieved by applying electrical fields to modulate phononic modes via nonlinear piezoelectricity of LN. Among two modes, we demonstrate Autler-Townes splitting (ATS), alternating current (a.c.) Stark shift, and Rabi oscillation with a maximum cooperativity of 4.18. Extending to three modes, we achieve non-reciprocal frequency conversions with an isolation up to 20 dB. Nonreciprocity can be tuned by the time delay between the two modulating pulses. Our cavity electro-acoustic platform could find broad applications in sensing, microwave signal processing, phononic computing, and quantum acoustics.

cond-mat.mes-hall↗

arXiv2025

Injection locking of GHz-frequency surface acoustic wave phononic crystal oscillator

Low-noise gigahertz (GHz) frequencies sources are essential for applications in signal processing, sensing, and telecommunications. Surface acoustic wave (SAW) resonator-based oscillators offer compact form factors and low phase noise due to their short mechanical wavelengths and high quality (Q) factors. However, their small footprint makes them vulnerable to environmental variation, resulting in their poor long-term frequency stability. Injection locking is widely used to suppress frequency drift of lasers and oscillators by synchronizing to an ultra-stable reference. Here, we demonstrate injection locking of a 1-GHz SAW phononic crystal oscillator, achieving 40-dB phase noise reduction at low offset frequencies and unperturbed low noise at large offset frequencies. Compared to a free-running SAW oscillator, which typically exhibits frequency drifts of several hundred hertz over minutes, the injection-locked oscillator reduces the frequency deviation to below 0.35 Hz. We also investigate the locking range and oscillator dynamics in the injection pulling region. The demonstrated injection-locked SAW oscillator could find applications in high-performance portable telecommunications and sensing systems.

physics.app-ph↗

arXiv2025

Room-temperature mid-infrared detection using metasurface-absorber-integrated phononic crystal oscillator

Mid-infrared (MIR) detectors find extensive applications in chemical sensing, spectroscopy, communications, biomedical diagnosis and space explorations. Alternative to semiconductor MIR photodiodes and bolometers, mechanical-resonator-based MIR detectors show advantages in higher sensitivity and lower noise at room temperature, especially towards longer wavelength infrared. Here, we demonstrate uncooled room-temperature MIR detectors based on lithium niobate surface acoustic wave phononic crystal (PnC) resonators integrated with wavelength-and-polarization-selective metasurface absorber arrays. The detection is based on the resonant frequency shift induced by the local temperature change due to MIR absorptions. The PnC resonator is configured in an oscillating mode, enabling active readout and low frequency noise. Compared with detectors based on tethered thin-film mechanical resonators, our non-suspended, fully supported PnC resonators offer lower noise, faster thermal response, and robustness in both fabrication and practical applications. Our 1-GHz oscillator-based MIR detector shows a relative frequency deviation of $5.24 \times 10^{-10}$ Hz$^{-1/2}$ at an integration time of 50 ${\mu}$s, leading to an incident noise equivalent power of 197 pW/$\sqrt{\mathrm{Hz}}$ when input 6-${\mu}$m MIR light is modulated at 1.8 kHz, and a large dynamic range of 107 in incident MIR power. Our device architecture is compatible with the scalable manufacturing process and can be readily extended to a broader spectral range by tailoring the absorbing wavelengths of metasurface absorbers.

physics.optics↗

arXiv2024

Low-phase-noise surface-acoustic-wave oscillator using an edge mode of a phononic band gap

Low-phase-noise microwave-frequency integrated oscillators provide compact solutions for various applications in signal processing, communications, and sensing. Surface acoustic waves (SAW), featuring orders-of-magnitude shorter wavelength than electromagnetic waves at the same frequency, enable integrated microwave-frequency systems with much smaller footprint on chip. SAW devices also allow higher quality (Q) factors than electronic components at room temperature. Here, we demonstrate a low-phase-noise gigahertz-frequency SAW oscillator on 128{\deg}Y-cut lithium niobate, where the SAW resonator occupies a footprint of 0.05 mm$^2$. Leveraging phononic crystal bandgap-edge modes to balance between Q factors and insertion losses, our 1-GHz SAW oscillator features a low phase noise of -132.5 dBc/Hz at a 10 kHz offset frequency and an overlapping Hadamard deviation of $6.5\times10^{-10}$ at an analysis time of 64 ms. The SAW resonator-based oscillator holds high potential in developing low-noise sensors and acousto-optic integrated circuits.

physics.app-ph↗

arXiv2024

Frequency-domain Parallel Computing Using Single On-Chip Nonlinear Acoustic-wave Device

Multiply-accumulation (MAC) is a crucial computing operation in signal processing, numerical simulations, and machine learning. This work presents a scalable, programmable, frequency-domain parallel computing leveraging gigahertz (GHz)-frequency acoustic-wave nonlinearities. By encoding data in the frequency domain, a single nonlinear acoustic-wave device can perform a billion arithmetic operations simultaneously. A single device with a footprint of 0.03 mm$^2$ on lithium niobate (LN) achieves 0.0144 tera floating-point operations per second (TFLOPS), leading to a computing area density of 0.48 TFLOPS/mm$^2$ and a core power efficiency of 0.14 TFLOPS/Watt. As applications, we demonstrate multiplications of two 16-by-16 matrices and convolutional imaging processing of 128-by-128-pixel photos. Our technology could find versatile applications in near-sensor signal processing and edge computing.

physics.app-ph↗

arXiv2024

Higher-order Skin Effect through a Hermitian-non-Hermitian Correspondence and Its Observation in an Acoustic Kagome Lattice

The non-Hermitian skin effect (NHSE) is a distinctive topological phenomenon observed in nonHermitian systems. Recently, there has been considerable interest in exploring higher-order NHSE occurrences in two and three dimensions. In such systems, topological edge states collapse into a corner while bulk states remain delocalized. Through a Hermitian-non-Hermitian correspondence, this study predicts and experimentally observes the higher-order NHSE in an acoustic Kagome lattice possessing nonreciprocal hoppings. By rotating the frequency spectrum and employing complexfrequency excitation techniques, we observe the localization of acoustic energy towards a corner of the lattice in the topologically nontrivial phase, even when the source is located far from that corner. In contrast, the acoustic energy spreads out when excited at the frequencies hosting the bulk states. These observations are unequivocal evidence of the higher-order NHSE.

cond-mat.mes-hall↗

arXiv2020

Magic-angle Bilayer Phononic Graphene

Thanks to the recent discovery on the magic-angle bilayer graphene, twistronics is quickly becom11 ing a burgeoning field in condensed matter physics. This letter expands the realm of twistronics to acoustics by introducing twisted bilayer phononic graphene, which remarkably also harbors the magic angle, evidenced by the associated ultra-flat bands. Beyond mimicking quantum mechanical behaviors of twisted bilayer graphene, we show that their acoustic counterpart offers a considerably more straightforward and robust way to alter the interlayer hopping strength, enabling us to unlock magic angles (> 3 degrees) inaccessible in classical twisted bilayer graphene. This study, not only establishes the acoustical analog of twisted (magic-angle) bilayer graphene, providing a testbed more easily accessible to probe the interaction and misalignment between stacked 2D materials, but also points out the direction to a new phononic crystal design paradigm that could benefit applications such as enhanced acoustic emission and sensing.

cond-mat.mes-hall↗

arXiv2020

Low-frequency broadband acoustic metasurface absorbing panels

A broadband sound absorption attained by a deep-subwavelength structure is of great interest to the noise control community especially for extremely low frequencies (20-100 Hz) in room acoustics. Coupling multiple different resonant unit cells has been an effective strategy to achieve a broadband sound absorption. In this paper, we report on an analytical, numerical and experimental study of a low-frequency broadband (50-63 Hz, one third octave band), high absorption (average absorption coefficient around 93%), near-omnidirectional (0{\deg}-75{\deg}) acoustic metasurface absorber composed of 4 coupled unit cells at a thickness of 15.4 cm (1/45 of the wavelength at 50 Hz). The absorption by such a deep-subwavelength structure occurs due to a strong coupling between unit cells, which is realized by carefully engineering geometric parameters of each unit cell, especially the judicious assignment of lateral size to each unit cell. To further broaden the bandwidth (50-100 Hz, one octave band), a design with 19 unit cells coupled in a supercell is analytically studied to achieve an average absorption coefficient of 85% for a wide angle range (0{\deg}-75{\deg}) at a thickness of 20 cm (1/34 of wavelength at 50 Hz). Two additional degrees of freedom, the lateral size of supercell and the number of unit cells in the supercell, are demonstrated to facilitate such a causally optimal design which is close to the ideally causal optimality. The proposed design methodology may solve the long-standing issue for low frequency absorption in room acoustics.

physics.app-ph↗

arXiv2015

Binary Frequencies in Globular Clusters

Binary stars are predicted to have an important role in the evolution of globular clusters, so we obtained binary fractions for 35 globular clusters that were imaged in the F606W and F814W with the ACS on the Hubble Space Telescope. When compared to the values of prior efforts (Sollima et al. 2007; Milone et al. 2012), we find significant discrepancies, despite each group correcting for contamination effects and having performed the appropriate reliability tests. The most reliable binary fractions are obtained when restricting the binary fraction to q > 0.5. Our analysis indicates that the range of the binary fractions is nearly an order of magnitude for the lowest dynamical ages, suggesting that there is a broad distribution in the binary fraction at globular cluster formation. Dynamical effects also appears to decrease the core binary fractions by a factor of two over a Hubble time, but this is a weak relationship. We confirm a correlation from previous work that the binary fraction within the core radius decreases with cluster age, indicating that younger clusters formed with higher binary fractions. The strong radial gradient in the binary fraction with cluster radius appears to be a consequence of dynamical interactions. It is often not present in dynamically young clusters but nearly always present in dynamically old clusters.

astro-ph.GA↗

arXiv2013

Binary Frequencies in a Sample of Globular Clusters. I. Methodology and Initial Results

Binary stars are thought to be a controlling factor in globular cluster evolution, since they can heat the environmental stars by converting their binding energy to kinetic energy during dynamical interactions. Through such interaction, the binaries determine the time until core collapse. To test predictions of this model, we have determined binary fractions for 35 clusters. Here we present our methodology with a representative globular cluster NGC 4590. We use HST archival ACS data in the F606W and F814W bands and apply PSF-fitting photometry to obtain high quality color-magnitude diagrams. We formulate the star superposition effect as a Poisson probability distribution function, with parameters optimized through Monte-Carlo simulations. A model-independent binary fraction of (6.2 +- 0.3)% is obtained by counting stars that extend to the red side of the residual color distribution after accounting for the photometric errors and the star superposition effect. A model-dependent binary fraction is obtained by constructing models with a known binary fraction and an assumed binary mass-ratio distribution function. This leads to a binary fraction range of 6.8% to 10.8%, depending on the assumed shape to the binary mass ratio distribution, with the best fit occurring for a binary distribution that favors low mass ratios (and higher binary fractions). We also represent the method for radial analysis of the binary fraction in the representative case of NGC 6981, which shows a decreasing trend for the binary fraction towards the outside, consistent with theoretical predictions for the dynamical effect on the binary fraction.

astro-ph.GA↗

arXiv2009

Elemental Abundances in the X-Ray Gas of Early-Type Galaxies with XMM and Chandra Observations

The source of hot gas in elliptical galaxies is thought to be due to stellar mass loss, with contributions from supernova events and possibly from infall from a surrounding environment. This picture predicts supersolar values for the metallicity of the gas toward the inner part of the galaxy, which can be tested by measuring the gas phase abundances. We use high-quality data for 10 nearby early-type galaxy from XMM-Newton, featuring both the EPIC and the Reflection Grating Spectrometer, where the strongest emission lines are detected with little blending; some Chandra data are also used. We find excellent consistency in the elemental abundances between the different XMM instruments and good consistency with Chandra. Differences in abundances with aperture size and model complexity are examined, but large differences rarely occur. For a two-temperature thermal model plus a point source contribution, the median Fe and O abundances are 0.86 and 0.44 of the Solar value, while Si and Mg abundances are similar to that for Fe. This is similar to stellar abundances for these galaxies but supernovae were expected to enhance the gas phase abundances considerably, which is not observed.

astro-ph.HE↗