arXiv subjects

Karl K. Berggren

Publications and source records attributed to Karl K. Berggren.

At least 109 records · Page 6Linked to original sources

arXiv2015

Designs for a Quantum Electron Microscope

One of the astounding consequences of quantum mechanics is that it allows the detection of a target using an incident probe, with only a low probability of interaction of the probe and the target. This 'quantum weirdness' could be applied in the field of electron microscopy to generate images of beam-sensitive specimens with substantially reduced damage to the specimen. A reduction of beam-induced damage to specimens is especially of great importance if it can enable imaging of biological specimens with atomic resolution. Following a recent suggestion that interaction-free measurements are possible with electrons, we now analyze the difficulties of actually building an atomic resolution interaction-free electron microscope, or "quantum electron microscope". A quantum electron microscope would require a number of unique components not found in conventional transmission electron microscopes. These components include a coherent electron-beam splitter or two-state-coupler, and a resonator structure to allow each electron to interrogate the specimen multiple times, thus supporting high success probabilities for interaction-free detection of the specimen. Different system designs are presented here, which are based on four different choices of two-state-couplers: a thin crystal, a grating mirror, a standing light wave and an electro-dynamical pseudopotential. Challenges for the detailed electron optical design are identified as future directions for development. While it is concluded that it should be possible to build an atomic resolution quantum electron microscope, we have also identified a number of hurdles to the development of such a microscope and further theoretical investigations that will be required to enable a complete interpretation of the images produced by such a microscope.

physics.ins-det↗

arXiv2015

Single-molecule study on the orientation of coiled-coil proteins attached to gold nanostructures

Methods for patterning biomolecules on a substrate at the single molecule level have been studied as a route to sensors with single-molecular sensitivity or as a way to probe biological phenomena at the single-molecule level. However, the arrangement and orientation of single biomolecules on substrates has been less investigated. Here, we examined the arrangement and orientation of two rod-like coiled-coil proteins, cortexillin and tropomyosin, around patterned gold nanostructures. The high aspect ratio of the coiled coils made it possible to study their orientations and to pursue a strategy of protein orientation via two-point attachment. The proteins were anchored to the surfaces using thiol groups, and the number of cysteine residues in tropomyosin was varied to test how this variation affected the structure and arrangement of the surface-attached proteins. Molecular dynamics studies were used to interpret the observed positional distributions. Based on initial studies of protein attachment to gold post structures, two 31-nm-long tropomyosin molecules were aligned between the two sidewalls of a trench with a width of 68 nm. Because the approach presented in this study uses one of twenty natural amino acids, this method provides a convenient way to pattern biomolecules on substrates using standard chemistry.

q-bio.BM↗

arXiv2015

Infrared Transmissometer to Measure the Thickness of NbN Thin Films

We present an optical setup that can be used to characterize the thicknesses of thin NbN films to screen samples for fabrication and to better model the performance of the resulting superconducting nanowire single photon detectors. The infrared transmissometer reported here is easy to use, gives results within minutes and is non-destructive. Thus, the thickness measurement can be easily integrated into the workflow of deposition and characterization. Comparison to a similar visible-wavelength transmissometer is provided.

physics.optics↗

arXiv2014

Universal scaling of the critical temperature for thin films near the superconducting-to-insulating transition

Thin superconducting films form a unique platform for geometrically-confined, strongly-interacting electrons. They allow an inherent competition between disorder and superconductivity, which in turn enables the intriguing superconducting-to-insulator transition and believed to facilitate the comprehension of high-Tc superconductivity. Furthermore, understanding thin film superconductivity is technologically essential e.g. for photo-detectors, and quantum-computers. Consequently, the absence of an established universal relationships between critical temperature ($T_c$), film thickness ($d$) and sheet resistance ($R_s$) hinders both our understanding of the onset of the superconductivity and the development of miniaturised superconducting devices. We report that in thin films, superconductivity scales as $d^.$$T_c(R_s)$. We demonstrated this scaling by analysing the data published over the past 46 years for different materials (and facilitated this database for further analysis). Moreover, we experimentally confirmed the discovered scaling for NbN films, quantified it with a power law, explored its possible origin and demonstrated its usefulness for superconducting film-based devices.

cond-mat.supr-con↗

arXiv2014

Eight-fold signal amplification of a superconducting nanowire single-photon detector using a multiple-avalanche architecture

Superconducting nanowire avalanche single-photon detectors (SNAPs) with n parallel nanowires are advantageous over single-nanowire detectors because their output signal amplitude scales linearly with n. However, the SNAP architecture has not been viably demonstrated for n > 4. To increase n for larger signal amplification, we designed a multi-stage, successive-avalanche architecture which used nanowires, connected via choke inductors in a binary-tree layout. We demonstrated an avalanche detector with n = 8 parallel nanowires and achieved eight-fold signal amplification, with a timing jitter of 54 ps.

physics.ins-det↗

arXiv2014

On-Chip Detection of Entangled Photons by Scalable Integration of Single-Photon Detectors

Photonic integrated circuits (PICs) have emerged as a scalable platform for complex quantum technologies using photonic and atomic systems. A central goal has been to integrate photon-resolving detectors to reduce optical losses, latency, and wiring complexity associated with off-chip detectors. Superconducting nanowire single-photon detectors (SNSPDs) are particularly attractive because of high detection efficiency, sub-50-ps timing jitter, nanosecond-scale reset time, and sensitivity from the visible to the mid-infrared spectrum. However, while single SNSPDs have been incorporated into individual waveguides, the system efficiency of multiple SNSPDs in one photonic circuit has been limited below 0.2% due to low device yield. Here we introduce a micrometer-scale flip-chip process that enables scalable integration of SNSPDs on a range of PICs. Ten low-jitter detectors were integrated on one PIC with 100% device yield. With an average system efficiency beyond 10% for multiple SNSPDs on one PIC, we demonstrate high-fidelity on-chip photon correlation measurements of non-classical light.

physics.optics↗

arXiv2014

A superconducting-nanowire 3-terminal electronic device

In existing superconducting electronic systems, Josephson junctions play a central role in processing and transmitting small-amplitude electrical signals. However, Josephson-junction-based devices have a number of limitations including: (1) sensitivity to magnetic fields, (2) limited gain, (3) inability to drive large impedances, and (4) difficulty in controlling the junction critical current (which depends sensitively on sub-Angstrom-scale thickness variation of the tunneling barrier). Here we present a nanowire-based superconducting electronic device, which we call the nanocryotron (nTron), that does not rely on Josephson junctions and can be patterned from a single thin film of superconducting material with conventional electron-beam lithography. The nTron is a 3-terminal, T-shaped planar device with a gain of ~20 that is capable of driving impedances of more than 100 kΩ, and operates in typical ambient magnetic fields at temperatures of 4.2K. The device uses a localized, Joule-heated hotspot formed in the gate to modulate current flow in a perpendicular superconducting channel. We have characterized the nTron, matched it to a theoretical framework, and applied it both as a digital logic element in a half-adder circuit, and as a digital amplifier for superconducting nanowire single-photon detectors pulses. The nTron has immediate applications in classical and quantum communications, photon sensing and astronomy, and its performance characteristics make it compatible with existing superconducting technologies. Furthermore, because the hotspot effect occurs in all known superconductors, we expect the design to be extensible to other materials, providing a path to digital logic, switching, and amplification in high-temperature superconductors.

cond-mat.supr-con↗

arXiv2012

Optimized polar-azimuthal orientations for polarized light illumination of different Superconducting Nanowire Single-Photon Detector designs

The optimal orientations are determined for polarized substrate side illumination of three superconducting nanowire single-photon detector (SNSPD) designs: (1) periodic niobium-nitride (NbN) stripes standing in air with dimensions according to conventional SNSPDs, (2) same NbN patterns below ~quarter-wavelength hydrogensilsesquioxane-filled nano-cavity, (3) analogous NbN patterns in HSQ nano-cavity closed by a thin gold reflector. Numerical computation results have shown that the optical response and near-field distribution vary significantly with polar-angle, fi, and these variations are analogous across all azimuthal-angles, gamma, but are fundamentally different in various device designs. Larger absorptance is available due to p-polarized illumination of NbN patterns in P-structure configuration, while s-polarized illumination results in higher absorptance in S-structure arrangement. As a result of p-polarized illumination a global maximum appears on absorptance of bare NbN pattern at polar angle corresponding to NbN-related ATIR; integration with HSQ nano-cavity results in a global absorptance maximum at polar angle corresponding to TIR at sapphire-air interface; while the highest absorptance is observable at perpendicular incidence on P-structures aligned below gold reflector covered HSQ nano-cavity. S-polarized light illumination results in a global absorptance maximum at TIR on bare NbN patterns; the highest absorptance is available below HSQ nano-cavity at polar angle corresponding to ATIR phenomenon; while the benefit of gold reflector is large and polar angle independent absorptance.

physics.optics↗

arXiv2011

Geometry-dependent critical currents in superconducting nanocircuits

In this paper we calculate the critical currents in thin superconducting strips with sharp right-angle turns, 180-degree turnarounds, and more complicated geometries, where all the line widths are much smaller than the Pearl length $Λ= 2 λ^2/d$. We define the critical current as the current that reduces the Gibbs free-energy barrier to zero. We show that current crowding, which occurs whenever the current rounds a sharp turn, tends to reduce the critical current, but we also show that when the radius of curvature is less than the coherence length this effect is partially compensated by a radius-of-curvature effect. We propose several patterns with rounded corners to avoid critical-current reduction due to current crowding. These results are relevant to superconducting nanowire single-photon detectors, where they suggest a means of improving the bias conditions and reducing dark counts. These results also have relevance to normal-metal nanocircuits, as these patterns can reduce the electrical resistance, electromigration, and hot spots caused by nonuniform heating.

cond-mat.supr-con↗

arXiv2011

Numerical method to optimize the Polar-Azimuthal Orientation of Infrared Superconducting Nanowire Single-Photon Detectors

A novel finite-element method for calculating the illumination-dependence of absorption in three-dimensional nanostructures is presented based on the RF module of the COMSOL software package. This method is capable of numerically determining the optical response and near-field distribution of sub-wavelength periodic structures as a function of illumination orientations specified by polar angle, fi, and azimuthal angle, gamma. The method was applied to determine the illumination-angle-dependent absorptance in cavity-based superconducting-nanowire single-photon detector (SNSPD) designs. Niobium-nitride stripes based on dimensions of conventional SNSPDs and integrated with ~ quarter-wavelength hydrogensilsesquioxane-filled nano-optical cavities and covered by a thin gold film acting as a reflector were illuminated from below by p-polarized light in this study. The numerical results were compared to results from complementary transfer-matrix-method calculations on composite layers made of analogous film-stacks. This comparison helped to uncover the optical phenomena contributing to the appearance of extrema in the optical response. This paper presents an approach to optimizing the absorptance of different sensing and detecting devices via simultaneous numerical optimization of the polar and azimuthal illumination angles.

physics.optics↗

arXiv2010

Electro thermal simulation of superconducting nanowire avalanche photodetectors

We developed an electro thermal model of NbN superconducting nanowire avalanche photodetectors (SNAPs) on sapphire substrates. SNAPs are single photon detectors consisting of the parallel connection of N superconducting nanowires. We extrapolated the physical constants of the model from experimental data and we simulated the time evolution of the device resistance, temperature and current by solving two coupled electrical and thermal differential equations describing the nanowires. The predictions of the model were in good quantitative agreement with the experimental results.

cond-mat.mtrl-sci↗

arXiv2008

Pulse calibration and non-adiabatic control of solid-state artificial atoms

Transitions in an artificial atom, driven non-adiabatically through an energy-level avoided crossing, can be controlled by carefully engineering the driving protocol. We have driven a superconducting persistent-current qubit with a large-amplitude, radio-frequency field. By applying a bi-harmonic waveform generated by a digital source, we demonstrate a mapping between the amplitude and phase of the harmonics produced at the source and those received by the device. This allows us to image the actual waveform at the device. This information is used to engineer a desired time dependence, as confirmed by detailed comparison with simulation.

cond-mat.supr-con↗

arXiv2008

Electrothermal feedback in superconducting nanowire single-photon detectors

We investigate the role of electrothermal feedback in the operation of superconducting nanowire single-photon detectors (SNSPDs). It is found that the desired mode of operation for SNSPDs is only achieved if this feedback is unstable, which happens naturally through the slow electrical response associated with their relatively large kinetic inductance. If this response is sped up in an effort to increase the device count rate, the electrothermal feedback becomes stable and results in an effect known as latching, where the device is locked in a resistive state and can no longer detect photons. We present a set of experiments which elucidate this effect, and a simple model which quantitatively explains the results.

cond-mat.supr-con↗

arXiv2008

Optical Properties of Superconducting Nanowire Single-Photon Detectors

We measured the optical absorptance of superconducting nanowire single photon detectors. We found that 200-nm-pitch, 50%-fill-factor devices had an average absorptance of 21% for normally-incident front-illumination of 1.55-um-wavelength light polarized parallel to the nanowires, and only 10% for perpendicularly-polarized light. We also measured devices with lower fill-factors and narrower wires that were five times more sensitive to parallel-polarized photons than perpendicular-polarized photons. We developed a numerical model that predicts the absorptance of our structures. We also used our measurements, coupled with measurements of device detection efficiencies, to determine the probability of photon detection after an absorption event. We found that, remarkably, absorbed parallel-polarized photons were more likely to result in detection events than perpendicular-polarized photons, and we present a hypothesis that qualitatively explains this result. Finally, we also determined the enhancement of device detection efficiency and absorptance due to the inclusion of an integrated optical cavity over a range of wavelengths (700-1700 nm) on a number of devices, and found good agreement with our numerical model.

physics.optics↗

arXiv2008

Photon-number-resolution with sub-30-ps timing using multi-element superconducting nanowire single photon detectors

A photon-number-resolving detector based on a four-element superconducting nanowire single photon detector is demonstrated to have sub-30-ps resolution in measuring the arrival time of individual photons. This detector can be used to characterize the photon statistics of non-pulsed light sources and to mitigate dead-time effects in high-speed photon counting applications. Furthermore, a 25% system detection efficiency at 1550 nm was demonstrated, making the detector useful for both low-flux source characterization and high-speed photon-counting and quantum communication applications. The design, fabrication and testing of this detector are described, and a comparison between the measured and theoretical performance is presented.

physics.ins-det↗

arXiv2008

Amplitude Spectroscopy of a Solid-State Artificial Atom

The energy-level structure of a quantum system plays a fundamental role in determining its behavior and manifests itself in a discrete absorption and emission spectrum. Conventionally, spectra are probed via frequency spectroscopy whereby the frequency νof a harmonic driving field is varied to fulfill the conditions ΔE = h ν, where the driving field is resonant with the level separation ΔE (h is Planck's constant). Although this technique has been successfully employed in a variety of physical systems, including natural and artificial atoms and molecules, its application is not universally straightforward, and becomes extremely challenging for frequencies in the range of 10's and 100's of gigahertz. Here we demonstrate an alternative approach, whereby a harmonic driving field sweeps the atom through its energy-level avoided crossings at a fixed frequency, surmounting many of the limitations of the conventional approach. Spectroscopic information is obtained from the amplitude dependence of the system response. The resulting ``spectroscopy diamonds'' contain interference patterns and population inversion that serve as a fingerprint of the atom's spectrum. By analyzing these features, we determine the energy spectrum of a manifold of states with energies from 0.01 to 120 GHz \times h in a superconducting artificial atom, using a driving frequency near 0.1 GHz. This approach provides a means to manipulate and characterize systems over a broad bandwidth, using only a single driving frequency that may be orders of magnitude smaller than the energy scales being probed.

cond-mat.supr-con↗

arXiv2007

Controlling the optical properties of transparent media by mixing active and passive resonances

Novel optical phenomena, including electromagnetically induced transparency, slow light, superluminal light propagation, have recently been demonstrated in diverse physical implementations. These phenomena are challenging to realize in practical systems because they require quantum coherence as well as careful preparation and control of prescribed quantum states. Here we present a unified approach to engineering optical materials that exhibit these phenomena by using mixtures of active and passive optical materials at frequencies near their resonances. Our approach does not depend on quantum coherence and can realize large and small (much less than 1) indices of refraction and negative permittivity ($ε<0$), normal and anomalous dispersion, all while maintaining transparency.

physics.optics↗

arXiv2007

Constriction-limited detection efficiency of superconducting nanowire single-photon detectors

We investigate the source of large variations in the observed detection effiiencies of superconducting nanowire single-photon detectors between many nominally identical devices. Through both electrical and optical measurements, we infer that these variations arise from "constrictions:" highly localized regions of the nanowires where the effective cross-sectional area for superconducting current is reduced. These constrictions limit the DC bias current density to well below its critical value over the remainder of the wire, and thus prevent the detection efficiency from reaching the high values that occur in these devices only when they are biased near the critical current density.

physics.ins-det↗